Mg-Al-CO_3与Zn-Al-CO_3水滑石热稳定性差异的研究

层状双金属氢氧化物（ Layered double hydroxides,简称 LDHs）是一类近年来发展迅速的阴离子型粘土,又称水滑石,其组成通式为： [M? 1-xM? x(OH)2]x＋ Ax/nn-mH2O,其中 M?是二价金属离子, M?是三价金属离子, An－是阴离子。这种材料是由相互平行的层板组成,层板带有永久正电荷;层间具有可交换的阴离子以维持电荷平衡。通过离子交换可在层间嵌入不同的基团,制备许多功能材料,被广泛用作催化剂、吸附剂及油田化学品等,已引起人们的关 注 [1～ 4]。有关 Mg-Al-CO3与 Zn-Al-CO3水滑石的合成及性能研究国内外已有大量报道 [1…     

Mg/Zn/Al类水滑石的热分解和水化性能研究

采用共沉淀法制备了Mg2Al1、Zn2Al1和Mg1Zn1Al1LDHs,利用XRD和SEM表征手段,对它们的热分解及焙烧物在Na2CO3溶液中恢复层状结构的能力进行了对比研究。结果表明,在400～700℃温度范围内,Zn2Al1LDH和Mg2Al1LDH的焙烧物中均出现氧化物相(ZnO和MgO)和尖晶石相(ZnAl2O4和MgAl2O4相);而Mg1Zn1Al1LDH的焙烧物中始终以ZnO相为主,仅在700℃时出现微弱的MgAl2O4相。三种焙烧物恢复层状结构的能力为:Mg1Zn1Al1LDO>Mg2Al1LDO>Zn2Al1LDO,其与焙烧物组成有关。原始LDHs和水化LDHs均呈片状。     

均分散类水滑石纳米粒子的合成

类水滑石;平均粒径;粒径分布;均分散胶体;层状双金属氢氧化物     

MgAl-水滑石热分解过程动力学研究

类水滑石化合物Hydrotalcite-like Compounds(简称HTLcs)又称阴离子粘土,是由带正电荷的氢氧化物层和层间阴离子构成[1]。由于在类水滑石结构中含有大量的结构羟基和层间可分解的阴离子,所以其热稳定性较差,易于分解形成具有一定酸碱性及大比表面的复合氧化物,该复合氧化物由于具有晶粒小、活性元素分布均匀、比表面积大等特点,表现出了优异的催化性能[2~5]。近年来,以HTLcs为前体经高温焙烧制备双金属复合氧化物备受关注[6]。揭示类水滑石热解机理、选择焙烧条件是催化剂制备的关键所在。本文利用TG-DTA技术详细研究了不同镁铝比HTL…     

含铈类水滑石的制备及其衍生物催化研究

采用共沉淀水热法制备了镍铝铈三元复合层状氢氧化物.详细探讨了合成体系pH值、Ce/Al比及陈化条件对合成产物物相的影响;通过XRD,ICP,TG-DTA手段研究了合成物物相、组成及热行为.考察了以合成物为前驱体经焙烧后转化为镍铝铈复合金属氧化物在催化消除NO反应中的应用.实验结果表明,合成镍铝铈三元复合层状氢氧化物的适宜条件是:M2 /M3 =2,Ce/Al=0.07～0.75,pH=5.5～6.9,水热处理条件为110℃,5 h;在pH=5.5～6.9条件下,合成原料配比不同,产物物相相同,但组成不同;合成物热稳定性较差,在T=100～400℃之间,层间吸附水及层间平衡阴离子NO3-脱去,转化为复合氧化物,将此氧化物应用于NO消除反应中,表现出高的低温活性,400℃进行反应,NO转化率达95%,N2选择性几乎100%.     

水滑石晶体长厚比及晶粒尺寸控制方法研究

层状双金属氢氧化物（LayeredDoubleHydrox－ides，简称LDH）是一类重要的无机晶体材料，因其具有层状结构以及层板元素的可调控性和层间阴离子的可交换性，在催化、离子交换、吸附、医药犤１～８犦等方面具有广泛的用途，已受到人们越来越广泛的关注。近年来，随该类材料应用领域的不断拓展，在许多情况下要求LDH晶体具有小的粒径尺寸，以便最大限度地发挥其功能性。例如将LDH作为阻燃剂犤９犦使用，小粒径粉体可增强与聚合物基材的相容性，提高材料的阻燃、抑烟和力学性能。另一方面，因LDH具有层状结构，在复合材料中其层板能有效…     

钴铁和镁铁水滑石的合成及热稳定性差异的研究

采用低过饱和共沉淀法合成了n(Co或Mg)：n(Fe)=2：1,3：1,4：1的钴铁和镁铁水滑石。XRD分析表明两者晶体结构相似,但TG—DTA分析表明两者热稳定性存在显著差异,钴铁水滑石只在180℃附近有一个吸热峰,而镁铁水滑石在200℃和365℃附近有两个吸热峰,分别对应于层间水和层板羟基及层间碳酸根离子的脱除,这说明后者的层间水分子和碳酸根离子与层板上的羟基及金属原子之间的相互作用力强于前者,镁铁水滑石的热稳定性强于钴铁水滑石。     

Zn-Al-Ce三元类水滑石的制备及性质研究

采用共沉淀法，水热合成层状化合物一硝酸根柱撑锌铝铈三元类水滑石，分别测定了各种单一金属盐溶液及M^2 ／M^3 摩尔比为2，Ce^3 ／Al^3 摩尔比为0．25的混合金属盐的NaOH滴定曲线，并利用XRD对不同条件下合成产物进行物相分析。实验结果表明：在M^2 ／M^2 =2，Ce^3 ／Al^3 =0．07～0．50，pH=5．8～6．5条件下进行多种离子共沉淀，并经120℃、6h水热处理后，均能合成结构单一的ZnAlCe—HTLLcs，利用TG—DTlA、FT—IR、ICP对合成物进行了表征，筛选出适宜的合成条件，并对HTLcs层状结构的热行为进行初步研究，结果表明ZnAlCe—HTLcs热稳定性较差，层间结合水、层板羟基及层间客体物种(NO3^-)失去温度在240℃左右，易于转化为复合氧化物，将此复合氧化物应用于NO的催化?肖除反应，680℃下NO的转化率高达近100％。     

基于水滑石衍生钌催化剂光驱动合成氨的研究

通过在还原性气氛中煅烧钌基水滑石前驱体,制备了高度分散于金属氧化物纳米片上的钌纳米颗粒(Mg Al Ru-500R).利用X射线衍射(XRD)、高分辨透射电子显微镜(HRTEM)、X射线光电子能谱(XPS)和紫外-可见-近红外漫反射光谱(UV-Vis-NIR DRS)对Mg Al Ru-500R的晶体结构、形貌、元素组成和光学特性进行分析表征.基于流动相反应体系研究了Mg Al Ru-500R催化剂在常压条件下的光热催化合成氨性能.结果表明,Mg Al Ru-500R可以仅依靠光照升温至300℃以上,并驱动光热催化合成氨反应.在380℃下,Mg Al Ru-500R光热催化合成氨速率高达3.0 mmol·g^?1·h^?1,显著高于相同温度下的热催化合成氨速率(1.5 mmol·g^?1·h^?1).动力学分析(包括表观活化能和动力学反应级数的测定)结果表明,优异的光热催化合成氨活性是因为光激发加速了N₂解离,进而降低了反应活化能.     

含铜类水滑石催化材料热分解过程的研究

共沉淀法合成了Cu0.13Mg0 6Al0.27(OH)2(CO3)0.135·xH2O类水滑石物质 (CuHTlc) ,采用XRD、DTA TG、BET、TEM和27AlMASNMR技术对其热分解过程进行了表征。结果表明 ,在较低焙烧温度时 (低于300℃ ),氢氧根和层间水部分脱除 ,但水滑石仍保持其层状结构 ;500℃时 ,其层状结构被完全破坏 ,出现氧化镁晶相结构 ,随着焙烧温度的进一步升高 ,尖晶石晶相生成。500℃时的焙烧产物具有最大比表面 (193m2·g-1)。当温度高于500℃ ,焙烧产物组成可表示为Cu0.13Mg0.6Al0.27O0.135,CuHTlc的热分解过程可表示为 :Cu0.13Mg0.6Al0.27(OH)2(CO3)0.135·xH2O→Cu0.13Mg0.6Al0.27O0.135 (1 x)H2O 0.135CO2。     

Cr2(WO4)3和Cr2(MoO4)3的负热膨胀特性研究

用液相反应-前驱物烧结法制备了Cr₂(WO₄)₃和Cr₂(MoO₄)₃粉体。298～1 073 K的原位粉末X射线衍射数据表明Cr₂(WO₄)₃和Cr₂(MoO₄)₃的晶胞体积随温度的升高而增大, 本征线热膨胀系数分别为(1.274±0.003)×10^-6 K^-1和(1.612±0.003)×10^-6 K^-1。用热膨胀仪研究了Cr₂(WO₄)₃和Cr₂(MoO₄)₃在静态空气中298～1 073 K范围内热膨胀行为，即开始表现为正热膨胀，随后在相转变点达到最大值，最后表现为负热膨胀，其负热膨胀系数分别为(-7.033±0.014)×10^-6 K^-1和(-9.282±0.019)×10^-6 K^-1。     

Thermal Stability of Pt/Al2O3 Catalysts Prepared by Sol-Gel

A series of Pt/Al₂O₃ catalysts were prepared using a sol-gel method. The influence of several parameters used in the synthesis including: metal content, identity of the metal precursor, and the water/alkoxide ratio on the structural properties of the fresh (dried) and calcined samples were studied. It was found that the BET surface area decreased with an increase in the platinum content. A surface area of 500 m²/g was obtained following calcination at 773 K. The structure of fresh samples as determined by FTIR corresponded to that of a pseudoboehmite structure. Samples prepared using a water/alkoxide ratio (H₂O/ATB) of 9 showed a well-defined, uniform pore size distribution following calcination at 773 K. Metal dispersions comparable to those obtained using impregnation methods were obtained. Aging studies (calcination at 873 K for 24 h) performed on these catalysts, exhibited sintering behavior which were similar to Pt/Al₂O₃ catalysts prepared by other methods. The sample prepared using a H₂O/ATB ratio of 9 had the highest surface area and was more thermally resistant towards metal sintering. A bimodal metal particle size distribution was observed: some particles exhibited sintering while others of similar size showed a greater thermal stability to sintering. The sample having the largest surface area and the highest thermal stability following thermal treatment was a consequence of a more condensed structure and a higher pore roughness obtained after drying the gel. This enabled the formation of an alumina structure which was more amorphous and limited aggregation of platinum particles due to surface diffusion within the pore structure.     

Non-centrosymmetric Ba3Ti3O6(BO3)2

The compound previously reported as Ba₂Ti₂B₂O₉ has been reformulated as Ba₃Ti₃B₂O₁₂, or Ba₃Ti₃O₆(BO₃)₂, a new barium titanium oxoborate. Small single crystals have been recovered from a melt with a composition of BaTiO₃:BaTiB₂O₆ (molar ratio) cooled between 1100°C and 850°C. The crystal structure has been determined by X-ray diffraction: hexagonal system, non-centrosymmetric space group, a=8.7377(11) Å, c=3.9147(8) Å, Z=1, wR(F²)=0.039 for 504 unique reflections. Ba₃Ti₃O₆(BO₃)₂ is isostructural with K₃Ta₃O₆(BO₃)₂. Preliminary measurements of nonlinear optical properties on microcrystalline samples show that the second harmonic generation efficiency of Ba₃Ti₃O₆(BO₃)₂ is equal to 95% of that of LiNbO₃.     

反式2-甲基-2-丁烯酸甲酯与臭氧反应机理的计算研究

采用G3B3方法构建反式2-甲基-2-丁烯酸甲酯与O3反应体系以及后续Criegee自由基有、无水分子参与下异构化反应的势能面剖面.结果表明,反式2-甲基-2-丁烯酸甲酯与O3反应首先生成一个稳定的五元环中间体,此中间体按断键位置不同后续裂解反应存在两条路径,分别生成产物P1(CH3CHOO+CH3OC(O)C(CH3)O)和P2(CH3CHO+CH3OC(O)C(CH3)OO).利用经典过渡态理论(TST)并结合Wigner矫正模型计算了200-1200 K温度区间内标题反应的速率常数kTST/W.计算结果显示,294 K时,该反应速率常数为7.55×10-18cm3molecule-1s-1,与Bernard等对类似反应所测实验值非常接近.生成的Criegee自由基(CH3CHOO和CH3OC(O)C(CH3)OO)可分别与水分子发生α-加成及β-氢迁移反应,其中Criegee自由基与水的α-加成反应较其与水的β-氢迁移反应具有优势.另外与无水分子参与CH3CHOO和CH3OC(O)C(CH3)OO异构化反应相比,水分子的参与使得异构化反应较为容易进行.     

Fe3O4磁液的悬浮率测定及稳定性研究

The paper first reported the preparation of ultrafine Fe₃O₄ powder about 8～10nm by improved chemical pre-cipitation method， then turned it into magnetic fluid. The phase analysis， morphology， ultrafine powder size and magnetic property were measured by XRD， TEM and vibrating sample magnetometer(VSM)，respectively. In ad-dition， a new method ， by analyzed the suspending percentage of Fe₃O₄ powder， was introduced to study the effects of concentration， pH value， centrifugal rate and time on the stability of the magnetic fluid.     

Thermal decomposition of the layered double hydroxides of formula Cu6Al2(OH)16CO3 and Zn6Al2(OH)16CO3

Zn-Al hydrotalcites and Cu-Al hydrotalcites were synthesised by coprecipitation method and analysed by X-ray diffraction (XRD) and thermal analysis coupled with mass spectroscopy. These methods provide a measure of the thermal stability of the hydrotalcite. The XRD patterns demonstrate similar patterns to that of the reference patterns but present impurities attributed to Zn(OH)₂ and Cu(OH)₂. The analysis shows that the d003 peak for the Zn-Al hydrotalcite gives a spacing in the interlayer of 7.59 ? and the estimation of the particle size by using the Debye-Scherrer equation and the width of the d003 peak is 590 ?. In the case of the Cu-Al hydrotalcite, the d003 spacing is 7.57 ? and the size of the diffracting particles was determined to be 225 ?. The thermal decomposition steps can be broken down into 4 sections for both of these hydrotalcites. The first step decomposition below 100°C is caused by the dehydration of some water absorbed. The second stage shows two major steps attributed to the dehydroxylation of the hydrotalcite. In the next stage, the gas CO₂ is liberated over a temperature range of 150°C. The last reactions occur over 400°C and involved CO₂ evolution in the decomposition of the compounds produced during the dehydroxylation of the hydrotalcite.     

硝酸镁在γ-Al2O3上的热分解及MgO/γ-Al2O3

研究了不同载量时Mg(NO     

BaPbO3与BaTiO3多晶态陶瓷缺陷结构对比

BaPbO，是具有类金属导电特性的钙钛矿结构导电陶瓷，其晶体结构由Ba2＋和O^2-离子紧密堆积形成，pb^4＋离子占据由O^2-离子形成的八面体空隙。BaTiO3同为钙钛矿结构的陶瓷材料，由Ba^2＋和O^2-离子紧密堆积形成，Ti^4＋离子占据由O^2-离子形成的八面体空隙。BaPbO3和BaTiO3的A位离子相同,B位离子都为可变价离子。     

Thermal stability and crystal structure of β-Ba3YB3O9

A new compound, β-Ba₃YB₃O₉, has been attained through solid phase transition from α-Ba₃YB₃O₉ at high temperatures. Differential thermal analysis (DTA) revealed the phase transition at about 1120°C, the melting temperature at about 1253°C. Its crystal structure has been determined from powder X-ray diffraction data. The refinement was carried out using the Rietveld method and the final refinement converged with R_p=10.5% and R_wp=13.7%. This compound belongs to the hexagonal space group R-3, with lattice parameters a=13.0441(1) Å and c=9.5291(1) Å. There are 6 formulas per unit cell and 7 atoms in the asymmetric unit. The structure of β-Ba₃YB₃O₉ is built up from Ba(Y)O₈, BaO₆ and YB₆O₁₈ units formed by one YO₆ octahedron and six BO₃ triangles with shared O atoms.