苦味酸在聚酰胺树脂上的吸附热力学及动力学

在静态下,考察了温度对聚酰胺树脂吸附水溶液中苦味酸的影响,探讨了吸附的热力学、动力学规律.结果表明:温度对吸附的影响较小,等温吸附规律可用Freundlich或Langmuir方程表示;吸附过程为熵驱动的吸热、熵增的自发过程;属物理吸附范畴;吸附动力学规律可用q=aeb/t吸附速率方程表示,属颗粒内扩散控制.     

硅胶自水溶液中吸附丙酸和丁酸的计量置换吸附模型

实验研究了硅胶在293、303和313 K下,从水溶液中对丙酸和丁酸的吸附.发现该吸附服从液 固吸附中的计量置换吸附模型（SDM A）.根据吸附模型的线性参数研究了吸附热力学和吸附机理.该吸附是一个自发的、放热的熵减少过程.丁酸的标准吸附自由能比丙酸大,而标准吸附焓比丙酸小.推导出了实验条件下吸附自由能变化的计算公式.     

活性炭吸附CO2与其微孔体积的关系

对五种活性炭样品进行液氮温度下的N2吸附、碘吸附测定和冰点下的CO2吸附表征。结果表明,碘吸附值测定法和基于N2吸附等温线的BET方程、D-R方程,孔结构参数都不能正确反映活性炭对CO2的吸附特性;由CO2吸附等温线得到的D A模型参数也不适合分析活性炭吸附CO2特性;CO2吸附等温线的密度泛函理论（DFT）分析结果表明,CO2在活性炭上的吸附发生在极微孔内,DFT分析的微孔孔容与吸附等温线反映的吸附性能完全一致。因此,根据CO2吸附等温线的DFT模型是准确反映活性炭吸附CO2特性的表征分析方法。     

Adsorption volume and absolute adsorption: 2. Adsorption from liquid phase

A critical analysis of the isotherms of excess and absolute adsorption, as well as the adsorption space performed in the first part [1] is continued; however, as applied to the equilibrium physical adsorption from the liquid phase. The correct method is proposed for evaluating the adsorption volume of solid adsorbents with an arbitrary structure by the isotherm of excess adsorption of binary mixture of liquids. This method is successfully tested for nine different adsorption systems.     

Adsorption volume and absolute adsorption: 1. Adsorption from a gaseous phase

Important concepts of adsorption science, such as excess and absolute adsorption isotherms and adsorption space volume, are critically analyzed and their status is discussed. An adequate method is proposed for evaluating the adsorption volume of solid adsorbents having arbitrary structures from excess adsorption isotherms. The method is tested by the example of five adsorption systems examined at a wide range of equilibrium pressures.     

Dynamic measurements of adsorption of hydrolyzed polyacrylamide (HPAM) onto hematite

The adsorption measurements of hydrolyzed polyacrylamide (HPAM) onto hematite suspension are carried out to study the dynamics of the polymer adsorption onto the suspension particles and to investigate the mode of the polymer adsorption. The polymer is found to show much affinity for the adsorption because of the opposite charges possessed by the polymeric flocculant and the suspension particles. Various adsorption parameters such as adsorption coefficient, the rate constants for the adsorption and desorption, are evaluated with the help of a recently proposed kinetic scheme. It is found that the extent of adsorption and the adsorption rate are adequately affected by increasing the pH of the suspension while, unexpectedly, the adsorption is found to show only a marginal increase on addition of Na₂SO₄. Both the amount of the adsorbed polymer and the adsorption rate are also found to increase with the degree of hydrolysis of the polyelectrolyte.     

Probing the mechanism of water adsorption in carbon micropores with multitemperature isotherms and water preadsorption experiments

The phenomenon of water adsorption in carbon micropores is examined through the study of water adsorption equilibrium in molecular sieving carbon. Adsorption and desorption isotherms are obtained over a wide range of concentrations from less than 0.1% to beyond 80% of the vapor pressure. Evidence is provided in support of a proposed bimodal water adsorption mechanism that involves the interaction of water molecules with functional groups at low relative pressures and the adsorption of water molecules between graphene layers at higher pressures. Decomposition of the equilibrium isotherm data through application of the extended cooperative multimolecular sorption theory, together with favorable quantitative comparison, provides support for the proposed adsorption mechanism. Additional support is obtained from a multitemperature study of water equilibrium. Temperatures of 20, 50, and 60 degrees C were probed in this investigation in order to provide isosteric heat of adsorption data for water interaction with the carbon molecular sieve. At low loading, the derived isosteric heat of adsorption is estimated to be 69 kJ/mol. This value is indicative of the adsorption of water to functional groups. At higher loading, the isosteric heat of adsorption decreases with increasing loading and approaches the heat of condensation, indicative of adsorption between graphene layers. Further support for the proposed adsorption mechanism is derived from carbon dioxide adsorption experiments on carbon molecular sieve that is preadsorbed with various amounts of water. Significant exclusion of carbon dioxide occurs, and a quantitative analysis that is based on the proposed bimodal water adsorption mechanism is employed in this investigation.     

大孔网状树脂对三丁基氯化锡的吸附特性研究

从热力学，动力学及柱上吸附三方面讨论了Ｘ－５大网树脂对三丁基氯化锡的吸附特性。结果表明，吸附剂的吸附过程以物理吸附为主，外表面，内表面的吸附率分别为３８％，６２％装柱动态吸附率主要取决于柱长及流速，而溶液盐度及ｐＨ值影响不大。     

Ca2＋交换的几种分子筛的氮氩分离性能

采用水溶液离子交换法制备了Ca2＋交换的4A、13X和LSX分子筛，并在25 ℃下测定了它们的静态吸附等温线和动态穿透曲线.研究发现， Ca2＋交换的4A、13X和LSX分子筛对氮的吸附性能都明显优于其相应的钠型分子筛，而它们对氩的吸附量变化不大，说明Ca2＋交换的这三种分子筛是较好的氮氩分离吸附剂.从动态吸附的结果来看，所研究的各种分子筛都有一个最优的吸附分离压力，在本论文研究的压力范围内，这个最优压力在0.6 MPa附近.由穿透曲线可推算出混合气体的吸附量，通过氮和氩在混合气体中的吸附量和相应纯气体吸附量的对比可以得出，对于氮氩吸附选择性较高的分子筛，氮的存在对氩的吸附量有较大的影响.     

腐植酸对砷的吸附作用研究

腐植酸中含有大量的极性基团,对金属离子有较强的吸附性能。运用氢化物-原子荧光光谱法,以泥炭腐植酸为原料,研究了腐植酸对砷(V)离子的吸附作用和腐植酸吸附剂中砷的回收,并得出了最佳的吸附和脱附条件。实验考察了酸度、时间分别对吸附和脱附的影响。结果表明,泥炭腐植酸对砷吸附的最佳模型为Freundlich吸附方程,当溶液成中性时腐植酸对砷的吸附量较大且趋于平稳。砷的浓度为1μg/mL,溶液的pH值为7,吸附时间控制在55min时,吸附效果最佳,最大吸附率为85.49%。脱附的最佳条件为:pH值14,脱附时间20min。     

Adsorption of aqueous Cu(II) and Ag(I) by silica anchored Schiff base decorated polyamidoamine dendrimers: Behavior and mechanism

A class of silica anchored Schiff base decorated polyamidoamine (PAMAM) dendrimers were synthesized for removing aqueous Cu(II) and Ag(I). The adsorption performance was investigated synthetically and the adsorption mechanism was revealed. Results indicate the adsorption capacity depends on dendrimer generation, solution pH, contact time, temperature and initial metal ion concentration. The optimum adsorption pH is 6 for both metal ion. Adsorption kinetic suggests the adsorption can achieve equilibrium at 180 and 150 min for Cu(II) and Ag(I). The kinetic process is found to be in good agreement with pseudo-second-order model and film diffusion is the rate-controlling step. The adsorption isotherm indicates the adsorption is proceeded by monolayer behavior with chemical mechanism. These adsorbents exhibit competitive adsorption capacity as compared with other reported adsorbents. Theoretical calculation demonstrates the participation of hydroxyl, carbonyl, and amide groups during the adsorption of Cu(II), while hydroxyl and amide groups are mainly responsible for capturing Ag(I).     

一种基于R语言的大孔吸附树脂预测模型的构建

针对精准筛选高选择性分离中药多糖的大孔吸附树脂时间冗长、操作繁琐的现状,该文构建了一种快速筛选大孔吸附树脂的预测模型.采用R语言建立大孔吸附树脂参数、葡聚糖分子量与吸附量之间的多源信息模型,利用多源信息模型快速预测和筛选对中药多糖具有最佳吸附效果的大孔吸附树脂类型.所建多源信息模型的相关系数(r2)为0.901 2,P...     

交联羧甲基壳聚糖吸附痕量汞研究

研究了交联羧甲基壳聚糖对Hg2 的吸附作用,探讨了溶液的pH值、反应时间、温度、样品体积、共存组分等因素对其吸附性能的影响.实验表明,在pH=5时,羧甲基壳聚糖对Hg2 的吸附性能很好,吸附率可迭95%以上,并且具有良好的重复使用性能,其吸附行为满足Langmuir等温式,饱和吸附容量为125.1mg/g,方法的相对标准偏差为7.8%.用于分析实际水样时,回收率达96～以上.     

水杨酸型螯合树脂对Fe(III)离子的螯合吸附行为

以5-氨基水杨酸(ASA)为胺化试剂, 使氯甲基化的交联聚苯乙烯(CMCPS)微球表面的苄氯基团发生亲核取代反应, 制得了水杨酸型螯合树脂ASA-CPS. 研究了该螯合树脂对金属离子的螯合吸附行为, 探讨了其吸附热力学与吸附机理, 考察了介质pH值对树脂螯合吸附性能的影响以及树脂对不同金属离子的螯合吸附能力. 实验结果表明, 水杨酸型螯合树脂ASA-CPS 对重金属离子具有强螯合吸附性能, 尤其对Fe3+离子表现出很强的螯合吸附能力, 常温下吸附容量可达21 g/100 g. 吸附过程属熵驱动的化学吸附过程, 升高温度, 吸附容量增高; 在可抑制金属离子水解的pH范围内, 介质的pH值越高, 螯合吸附能力越强; 对于性质不同的金属离子, ASA-CPS的吸附性能是有差别的, 吸附容量的顺序为Fe3+>Ni2+>Cu2+>Zn2+.     

Temperature Influence of Benzene Adsorption by a Microporous Silica

The theory for volume filling of micropores is used to describe benzene adsorption isotherms measured over a 25 K temperature range. The adsorption potential or molar work of adsorption for the isotherm at 298 K is derived and compared with Weibull, Gaussian, and gamma potential distribution functions. The Weibull function is fitted via a two-term Dubinin-Radushkevich (D-R) equation. The closest data fit occurs for the gamma distribution. The two-term D-R potentials are interpreted as indicating adsorption by primary micropores followed sequentially by secondary micropores. Analysis of the distribution of adsorption enthalpy for the porous solid compared with a nonporous standard suggests that the predominant pore width is 1.2 nm. The interpretation of the differential molar adsorption entropy at 298 K suggests that strongly localized adsorption occurs in the primary micropores and two-dimensional translational motion with rotation in the plane of the ring occurs in the secondary micropores. Copyright 2000 Academic Press.     

Modeling of gas adsorption equilibrium over a wide range of pressure: a thermodynamic approach based on equation of state

A thermodynamic approach based on the Bender equation of state is suggested for the analysis of supercritical gas adsorption on activated carbons at high pressure. The approach accounts for the equality of the chemical potential in the adsorbed phase and that in the corresponding bulk phase and the distribution of elements of the adsorption volume (EAV) over the potential energy for gas-solid interaction. This scheme is extended to subcritical fluid adsorption and takes into account the phase transition in EAV. The method is adapted to gravimetric measurements of mass excess adsorption and has been applied to the adsorption of argon, nitrogen, methane, ethane, carbon dioxide, and helium on activated carbon Norit R1 in the temperature range from 25 to 70 degrees C. The distribution function of adsorption volume elements over potentials exhibits overlapping peaks and is consistently reproduced for different gases. It was found that the distribution function changes weakly with temperature, which was confirmed by its comparison with the distribution function obtained by the same method using nitrogen adsorption isotherm at 77 K. It was shown that parameters such as pore volume and skeleton density can be determined directly from adsorption measurements, while the conventional approach of helium expansion at room temperature can lead to erroneous results due to the adsorption of helium in small pores of activated carbon. The approach is a convenient tool for analysis and correlation of excess adsorption isotherms over a wide range of pressure and temperature. This approach can be readily extended to the analysis of multicomponent adsorption systems.     

D301树脂对活性深蓝K-R的吸附性能

用D301树脂对活性深蓝K-R的吸附特征进行了研究.在所研究的温度和浓度范围内,用Freund lich方程能够很好地对吸附等温线进行拟合,吸附是吸热的优惠吸附过程.吸附焓、吸附自由能、吸附熵变的计算结果显示:△H>0,表明吸附是吸热过程;△G<0,表明吸附的自发性;△S>0,表明固/液界面上分子运动更为混乱.动力学研究表明,吸附过程受颗粒内扩散及其它扩散过程的共同控制.     

乙二胺硅胶复合材料对Zn2+的吸附特性

以γ-氯丙基三氯硅烷为偶联剂,将乙二胺偶合接枝在硅胶表面,合成对锌离子具有吸附作用的乙二胺硅胶复合材料（EDA/SiO2）,考察了Zn2+溶液pH值、初始浓度、吸附温度和吸附时间等因素对复合材料吸附性能的影响。 结果表明,在研究的溶液浓度及温度范围内,Zn2+溶液pH值对EDA/SiO2的吸附量影响显著,吸附的最佳pH值范围在3.0~5.5;Zn2+的吸附平衡数据符合Langmuir吸附模型,热力学数据显示,EDA/SiO2对Zn2+的吸附行为为一吸热且自发进行的过程,升高温度有利于吸附,并对此吸附行为作了解释;吸附动力学数据可用拟二级吸附动力学方程描述,得到的吸附速率常数与溶液初始浓度有关。     

Study of the State of Benzene Molecules Adsorbed on the Surfaces of Organic Derivatives of Kaolinite and Silica

Values and heats of benzene adsorption on modified kaolinite and silica samples are measured by adsorption calorimetry. Entropy diagrams are calculated for benzene adsorbed on these samples. Obtained results are compared to entropy losses theoretically calculated for benzene molecules using the models of ideal localized and nonlocalized adsorption. It is demonstrated that, depending on the type of an inorganic matrix, the nature of a modifier, and the degree of modification, the adsorption of benzene molecules on studied sorbents is described by the models of a supermobile nonlocalized adsorption or a nonlocalized adsorption accompanied by the loss of some rotational degrees of freedom. For a rare case of the supermobile adsorption of benzene on the modified silica, the vibration frequency of its molecules with respect to the surface is calculated.     

不同分子筛的氮氩分离性能

采用水溶液离子交换法制备了不同离子交换的13X和4A分子筛,并在25℃下测 定了它们的静态吸附等温线和动态穿透曲线。研究发现,Ca~(2+)离子和Li~+离子 交换的13X和4A分子筛对氮的吸附性能都明显优于其相应的钠型分子筛,而它们对 氩的吸附量变化不大,说明这两种离子交换的分子筛是较好的氮氩分离吸附剂。从 动态吸附的结果来看,所研究的各种分子筛都有一个最优的吸附分离压力,在本论 文研究的压力范围内,这个最优压力在0.6MPa附近。通过穿透曲线推算出的混合气 体吸附量和纯气体吸附量的对比可以得出,对于氮氩吸附选择性较高的分子筛,氮 的存在对氩的吸附量有较大的影响。