Sorbitan tristearate layers at the air/water interface studied by shear and dilatational interfacial rheology

The shear and dilatational rheology of condensed interfacial layers of the water-insoluble surfactant sorbitan tristearate at the air/water interface is investigated. A new interfacial shear rheometer allows measurements in both stress- and strain-controlled modes, providing comprehensive interfacial rheological information such as the interfacial dynamic shear moduli, the creep response to a stress pulse, the stress relaxation response to a strain step, or steady shear curves. Our experiments show that the interfacial films are both viscoelastic and brittle in nature and subject to fracture at small deformations, as was supported by in-situ Brewster angle microscopy performed during the rheological experiments. Although any large-deformation test is destructive to the sample, it is still possible to study the linear viscoelastic regime if the deformations involved are controlled carefully. Complementary results for the dilatational rheology in area step compression/expansion experiments are reported. The dilatational behavior is predominantly elastic throughout the frequency spectrum measured, whereas the layers exhibit generalized Maxwell behavior in shear mode within a deformation frequency regime as narrow as two decades, indicating the presence of additional relaxation mechanisms in shear as opposed to expansion/compression. If the transient rheological response from stress relaxation experiments is considered, then the data can be described well with a stretched exponential model both in the shear and dilatational deformations.     

Transient interfacial tension and dilatational rheology of diffuse polymer-polymer interfaces

We demonstrate the influence of molecular weight and molecular weight asymmetry across an interface on the transient behavior of the interfacial tension. The interfacial tension was measured as a function of time for a range of polymer combinations with a broad range of interfacial properties using a pendant/sessile drop apparatus. The results show that neglecting mutual solubility, assumed to be a reasonable approximation in many cases, very often does not sustain. Instead, a diffuse interface layer develops in time with a corresponding transient interfacial tension. Depending on the specific combination of polymers, the transient interfacial tension is found to increase or decrease with time. The results are interpreted in terms of a recently proposed model [Shi et al., Macromolecules 37, 1591 (2004)], giving relative characteristic diffusion time scales in terms of molecular weight, molecular weight distribution, and viscosities. However, the time scales obtained from this theoretical approach do not give a conclusive trend. Using oscillatory dilatational interfacial experiments the viscoelastic behavior of these diffusive interfaces is demonstrated. The time evolution of the interfacial tension and the dilatational elasticity show the same trend as predicted by the theory of diffuse interfaces, supporting the idea that the polymer combinations under consideration indeed form diffuse interfaces. The dilatational elasticity and the dilatational viscosity show a frequency dependency that is described qualitatively by a simple Fickian diffusion model and quantitatively by a Maxwell model. The characteristic diffusion times provided by the latter show that the systems with thick interfaces (tens of microseconds and more) can be considered as slower diffusive systems compared to the systems with thinner interfaces (a few micrometers in thickness and less) can be considered as fast diffusive systems.     

Chemical destabilization of crude oil based emulsions and asphaltene stabilized emulsions

A comparison of low and high molecular weight demulsifiers and their effect on both crude oil and asphaltene based water-in-oil emulsions is performed. Physical characteristics are given for crudes and for the chemicals. These parameters were then correlated with the demulsifier performance. Results indicate that a significant lowering of interfacial tension is required, but not sufficient for an efficient demulsification. Addition of the chemicals directly to the oil phase prior to emulsification, i.e., as inhibitors, increased the performance of the chemicals significantly. Received: 3 May 2000 Accepted: 10 July 2000     

Influence of interfacial rheology on the viscosity of concentrated emulsions

New models are developed for the viscosity of concentrated emulsions taking into consideration the effects of interfacial rheology and Marangoni phenomenon. The interface is assumed to be viscous with non-zero surface-shear and surface-dilational viscosities. The Marangoni effect is accounted for through non-zero Gibbs elasticity of the interface. The experimental viscosity data for a number of emulsion systems are interpreted in terms of the proposed models.     

Experimental study on high-pressure rheology of water/crude oil emulsion in the presence of methane

The crude oil is in most cases accompanied with water and natural gas. For this reason, it is important to understand the rheology of the oil emulsion. There are already many works relating to rheology of the oil/water emulsion. However, studies on high-pressure rheology of water/crude oil emulsion in the presence of CH₄ are rare. In this work, light crude oil with characteristics of high wax content, which is typical in Northwest China, was studied. The rheology of water/crude oil emulsion in the presence of CH₄ under various conditions were fully studied. The results show that the crude oil emulsion showed obvious characteristics of non-Newtonian fluid at a lower temperature. Before water fraction reached a certain limit, the viscosity increases with the increase of water fraction, when water fraction reaches and exceeds the limit the emulsion viscosity drops with the increase of water fraction. The shear stress–shear rate curves become similar as the increase of temperature, indicating the decreasing effect of temperature on the relation between shear stress and shear rate. When the pressure reaches 8 MPa, the shear stress measured with CH₄ in the system surpasses that measured without CH₄. At higher pressure, CH₄ shows obvious influence on the rheology.     

Stability of oil/water (ethanol,lysozyme or lysine) emulsions

Emulsions of n-tetradecane in water (0.1%^v/_^V) homogenized by ultrasounds (1 5 min) were stabilized by 0.5 or 1.0 M ethanol and in the presence of lysozyme (4 mg 100 ml⁻¹) or 1 mM lysine monohydrochloride (14.6 mg 100 ml⁻¹). The zeta potentials and multimodal size distributions of the droplets after 5, 15, 30, 60, 120 min, and 1 and 2 days were determined by dynamic light scattering technique using ZetaPlus apparatus (Brookhaven Instr., USA). Both parameters were determined on the same sample subsequently without any mixing. The effect of pH [4, 6.8 (natural), and 11] was also investigated. The most stable emulsions in 1 M ethanol solutions alone were at pH 6.8 and 11 (the effective diameter D_eff and 350 nm, respectively), while in 0.5 M at pH 4 (D_eff nm). The most stable emulsions with lysozyme were obtained at pH 4 and 1 M ethanol (D_eff nm), and with lysine at pH 6.8 and 0.5 M ethanol (D_eff nm). Except for the emulsions with lysozyme at pH 4 and 6.8, in the rest systems the zeta potentials were negative and ranged between −5 and −85 mV as a function of time and pH. The changes of zeta potential indicate that H⁺ ions are not much potential determining, while OH⁻ ions increase the negative zeta potentials. However, H⁺ ions affect functional groups of lysozyme molecules adsorbed on the alkane droplet, what appears in essential changes of zeta potential and even reversed sign of it in some systems. The results point that stability of these emulsions may also be determined by hydrogen bonding.     

Wettability of Freon hydrates in crude oil/brine emulsions

The surface energy of petroleum hydrates is believed to be a key parameter with regard to hydrate morphology and plugging tendency in petroleum production. As of today, the surface energy of natural gas hydrates is unknown, but will depend on the fluids in which they grow. In this work, the wettability of Freon hydrates is evaluated from their behavior in crude oil emulsions. For emulsions stabilized by colloidal particles, the particle wettability is a governing parameter for the emulsion behavior. The transition between continuous and dispersed phases as a function of brine volume in crude oil-brine emulsions containing Freon hydrates has been determined for 12 crude oils. Silica particles are used for comparison. The results show that phase inversion is highly dependent on crude oil properties. Based on the measured points of phase inversion, the wettability of the Freon hydrates generated in each system is evaluated as being oil-wet, intermediate-wet, or water-wet. Generation of oil-wet hydrates correlates with low hydrate plugging tendency. The formation of oil-wet hydrates will prevent agglomeration into large hydrate aggregates and plugs. Hence, it is believed that the method is applicable for differentiating oils with regard to hydrate morphology.     

Dewatering of crude oil emulsions 1. Rheological behaviour of the crude oil—water interface

Rheological properties of Buchan crude oil—water interfaces have been determined using a biconical bob rheometer. The effects of temperature and the presence of surface-active demulsifiers on film characteristics have been evaluated. Free oscillation and creep modes have been used, depending on the relative viscoelastic behaviour of the films. Film ageing is particularly significant, whilst temperature and the nature and concentration of any demulsification chemicals also contribute significantly. Further detailed understanding of interfacial film rheology is considered to be desirable for a complete appreciation of the stability of water-in-crude oil emulsions.     

Dewatering of crude oil emulsions 2. Interfacial properties of the asphaltic constituents of crude oil

The importance of the interfacial rheology in determining the stability of water-in-Buchan crude oil emulsions has been demonstrated in part 1 of this series of papers (R.A. Mohammed, A.I. Bailey, P.F. Luckham and S.E. Taylor, Colloids Surfaces A: Physicochem. Eng. Aspects, 80(1993)223). In part 2, interfacial tensions of crude oil, and solutions of asphaltenes and resins in a model oil have been investigated. Surface pressure vs. area (Π—A) curves of monolayers of asphaltenes, resins and their mixtures have been established. In its dependence on the ratio of resins to asphaltenes, the pseudostatic dilatational modulus has high values for low resin-to-asphaltene ratios and low values for high resin-to-asphaltene ratios. This is expected to throw light on the cause of the enhanced stability of water-in-crude oil emulsions.     

Determining partition constants of polar organic molecules between the oil/interfacial and water/interfacial regions in emulsions: a combined electrochemical and spectrometric method

We have developed a new approach for estimating distributions of polar additives in opaque, surfactant based, macroemulsions based on the pseudophase model for homogeneous micellar and microemulsion solutions. The distribution of a polar additive, such as an antioxidant, AO, within emulsions is expressed in terms of two partition constants, one between the oil and interfacial regions, P(O)I, and the other between the water and interfacial regions, P(W)I. To estimate values for P(O)I and P(W)I requires fitting two independent data sets with two independent mathematical relations and solving equations simultaneously for the two parameters. The experimental protocols were developed for determining the partition constants of tertbutylhydroquinone, TBHQ, in a stirred emulsion composed of octane, dilute aqueous acid, and hexaethyleneglycol monododecyl ether, C12E6. One data set was obtained by electrochemical determination of the observed rate constant, k(obs), for reaction of TBHQ with an arenediazonium ion probe as a function of C12E6 volume fraction. The second data set was obtained by determining the partition constant, P(O)W, of TBHQ between octane and water in the absence of surfactant by UV-visible spectrometry. TBHQ is almost 30 times more soluble in water than octane: P(O)W = 27.5. The values of the partition constants in the emulsion are P(O)I = 1.84 x 10(4) and P(W)I = 6.73 x 10(2). The partition constants were used to estimate the fraction of TBHQ in each region; for example, 96% of the TBHQ is located in the interfacial region at 0.02 volume fraction of C12E6. Our approach is quite general and should be applicable to any polar organic compound that reacts with the arenediazonium ion probe in emulsions composed of virtually any type of oil and surfactant. Comparisons of the rate constants for reaction of the antioxidant in the interfacial region of the emulsion, which can be obtained from the electrochemical results, may lead to a scale of antioxidant efficiency that is independent of the distribution of the antioxidant in the emulsion.     

Droplet surface properties and rheology of concentrated oil in water emulsions stabilized by heat-modified beta-lactoglobulin B

Effects of substituting native beta-lactoglobulin B (beta-lactoglobulin) with heat-treated beta-lactoglobulin as emulsifier in oil in water emulsions were investigated. The emulsions were prepared with a dispersed phase volume fraction of Phi=0.6, and accordingly, oil droplets rather closely packed. Native beta-lactoglobulin and beta-lactoglobulin heated at 69 degrees C for 30 and 45 min, respectively, in aqueous solution at pH 7.0 were compared. Molar mass determination of the species formed upon heating as well as measurements of surface hydrophobicity and adsorption to a planar air/water interface were made. The microstructure of the emulsions was characterized using confocal laser scanning microscopy, light scattering measurements of oil droplet sizes, and assessment of the amount of protein adsorbed to surfaces of oil droplets. Furthermore, oil droplet interactions in the emulsions were quantified rheologically by steady shear and small and large amplitude oscillatory shear measurements. Adsorption of heated and native beta-lactoglobulin to oil droplet surfaces was found to be rather similar while the rheological properties of the emulsions stabilized by heated beta-lactoglobulin and the emulsions stabilized by native beta-lactoglobulin were remarkably different. A 200-fold increase in the zero-shear viscosity and elastic modulus and a 10-fold increase in yield stress were observed when emulsions were stabilized by heat-modified beta-lactoglobulin instead of native beta-lactoglobulin. Aggregates with a radius of gyration in the range from 25 to 40 nm, formed by heating of beta-lactoglobulin, seem to increase oil droplet interactions. Small quantities of emulsifier substituted with aggregates have a major impact on the rheology of oil in water emulsions that consist of rather closely packed oil droplets.     

Interfacial cross-linking polymerisation process in oil/water emulsions

Summary We have studied the effect on the water-oil interfacial tension of a series of diacrylate molecules solubilized in the oil phase. Due to the weak tensio-active behaviour of these compounds, we have verified that the oil in water emulsions of this system were unstable. We have shown that these emulsions can be stabilized by polymerisation of the diacrylic molecules and that this process is essentially a surface cross-linking polymerisation.

---

Zusammenfassung Es wurde der Einfluß einer Reihe von Diacrylaten, die in der Ölphase solubilisiert waren, auf die WasserÖl-Grenzflächenspannung untersucht. Es konnte nachgewiesen werden, daß die Öl-in-Wasser-Emulsionen instabil sind, was der geringen Grenzflächenaktivität dieser Systeme entspricht. Es wurde weiter gezeigt, daß diese Emulsionen stabilisiert werden können durch Polymerisation der Diacrylate. Dieser Prozeß ist eine Oberflächen-Vernetzungs-Polymerisation.

---

---

Work partially supported by D. R. M. E. under contract number 73.34.099.

---

With 1 figure and 4 tables     

Selective membrane test for crude oil based model emulsions by use of video-enhanced microscopy

 A method for testing water/oil emulsion droplet membranes selectively has been demonstrated. The method uses electric fields to induce attraction, membrane thinning and coalescence between aqueous droplets deposited in an oil continuum. The coalescence process is monitored visually by the use of videomicroscopy. A set of model oils containing indigenous surfactants (asphaltenes) from a crude oil has been studied, and the effects of asphaltene concentration, oil phase aromaticity, aging of oils and interfacial exposure time have been investigated. The strength of the field at the point of coalescence is defined as the critical parameter describing membrane strength. In the current experiments a.c. fields were used and droplet sizes were of the order of 500–600 μm. Received: 8 October 1998 Accepted in revised form: 11 January 1999     

Stability and rheology of three types of W/O/W multiple emulsions emulsified with lecithin

Three types of multiple emulsions were prepared with lecithin. The morphology, stability, and rheological properties of the three types of W/O/W multiple emulsions were evaluated. The formulation factors, including salts and aliphatic alcohol, were further examined. The three types of multiple emulsions were formed by different emulsifiers. An excellent multiple emulsion occurred with 2?wt% lecithin concentration, stabilized by 0.05?wt% NaCl. All multiple emulsions showed shear-thinning behavior, i.e., the apparent viscosity decreased with the increase of the shear rate. With the high concentration of lecithin, the multiple emulsions exhibited the highest viscosity at low shear rate and had higher storage modulus (G′) and the loss modulus (G″). This study was conducted to reveal that different types of multiple emulsions can be formed with lecithin, and that the stability and rheological properties were different with different types of multiple emulsions.     

Novel thermo-responsive coloring phenomena in water/surfactant/oil emulsions

Emulsions comprising a dual-surfactant system of a long-chain amidoamine derivative and a quaternary ammonium salt developed an iridescent color at a specific temperature region. The emulsions underwent phase inversion on heating from an O/W emulsion to a W/O emulsion, passing through a periodical lamellar structure which developed a characteristic interference color. Interestingly, the color and the coloring temperature can be independently controlled by adjusting the concentration of surfactants, respectively.     

Properties of oil1/water/oil2 double emulsions containing lipophilic acrylic polymer

Stable oil₁/water/oil₂ (o₁/w/o₂) double emulsions (DEs) containing glyceryl monooleate as a promoter of skin permeability in internal ultradispersed phase o1 (heptane) and an acrylic polymer as a pressuresensitive adhesive in external dispersion medium o₂ (ethyl acetate) are obtained. The aqueous interlayer of the DEs contains Tween 80, hydroxypropyl cellulose, and sometimes lysozyme. The phase ratio in the emulsions is constant. The effect of polyacrylate concentration on the stability, microstructure, and rheological properties of DEs is studied. Factors of DE stability, with the viscoelastic properties of the external dispersion medium being of the most importance, are analyzed. The DEs are used to produce ultradisperse films, which exhibit long-term release of lysozyme at a constant rate with its enzymatic activity retained preserved. The diffusion coefficient of the protein in the polymer matrix is determined.     

Interfacial rheology of natural silk fibroin at air/water and oil/water interfaces

The interfacial viscoelastic behavior of natural silk fibroin at both the air/water and oil/water interfaces is reported. This natural multiblock copolymer is found to be strongly amphiphilic and forms stable films at these interfaces. The result is an interfacial layer that is rheologically complex with strong surface elastic moduli that are only slightly frequency-dependent. The kinetics of surface viscoelastic evolution are reported as functions of time for various concentrations of the spread films. Films deposited by Langmuir-Blodgett deposition were studied by scanning electron microscopy (SEM) to reveal a fibrous structure at the interface. The production of stable O/W emulsions by silk fibroin further confirms the generation of the elastic films at the oil/water interfaces.     

Effects of additional salts on the interfacial tension of crude oil/zwitterionic gemini surfactant solutions

Zwitterionic gemini surfactants, which have the advantages of both zwitterionic and gemini surfactants, have been widely used in various disciplines. Sulfobetaine-type zwitterionic gemini surfactants consisting of 1,2-bis[N-methyl-N-(3-sulfopropyl)-alkylammonium]ethane (2C_nSb with 6, 8 and 10 carbon atoms) were evaluated for their interfacial activities at the water/crude oil interface. The 2C₁₀Sb molecules showed a remarkable ability to decrease the interface tension (IFT) of water/crude oil, and the degree of decrease was much greater than those in either zwitterionic or gemini surfactant systems by at least two orders of magnitude. Furthermore, the effects of salts (NaCl, CaCl₂, and MgCl₂) on the IFT of the 2C₁₀Sb system were thoroughly investigated. Interestingly, the delicate balance between the effects of additional cations and the intramolecular interactions of 2C₁₀Sb molecules played crucial roles in the interfacial arrangements of 2C₁₀Sb molecules, which were mainly dependent on the bonding abilities of the cations. Moreover, a zwitterionic surfactant and a cationic gemini surfactant were employed in control experiments to verify the proposed mechanisms.