Effects of deposition temperature on the structural and morphological properties of thin ZnO films fabricated by pulsed laser deposition

ZnO thin films were grown on Si(1 0 0) substrates using pulsed laser deposition in O₂ gas ambient (10 Pa) and at different substrate temperatures (25, 150, 300 and 400 °C). The influence of the substrate temperature on the structural and morphological properties of the films was investigated using XRD, AFM and SEM. At substrate temperature of T=150 °C, a good quality ZnO film was fabricated that exhibits an average grain size of 15.1 nm with an average RMS roughness of 3.4 nm. The refractive index and the thickness of the thin films determined by the ellipsometry data are also presented and discussed.     

Structural and optical properties of SrCu2O2 films deposited on sapphire substrates by pulsed laser deposition

We deposited SrCu₂O₂ (SCO) films on sapphire (Al₂O₃) (0 0 0 1) substrates by pulsed laser deposition. The crystallographic orientation of the SCO thin film showed clear dependence on the growth temperature. X-ray diffraction (XRD) and transmission electron microscopy (TEM) analysis showed that the film deposited at 400 °C was mainly oriented in the SCO [2 0 0] direction, whereas when the growth temperature was increased to 600 °C, the SCO film showed a dominant orientation of SCO [1 1 2]. The SCO film deposited at 500 °C was obvious polycrystalline, showing multi peaks from (2 0 0), (1 1 2), and (2 1 1) diffraction in the XRD spectrum. The SCO film deposited at 600 °C showed a band gap energy of 3.3 eV and transparency up to 80% around 500 nm. The photoluminescence (PL) spectra of the SCO films grown at 500 °C and 600 °C mainly showed blue-green emission, which was attributed to the intra-band transition of the isolated Cu⁺ and Cu⁺–Cu⁺ pairs according to the temperature dependent-PL analysis.     

High temperature thermoelectric properties of highly c-axis oriented Bi2Sr2Co2Oy thin films fabricated by pulsed laser deposition

High-temperature thermoelectric transport property measurements have been performed on the highly c-axis oriented Bi2Sr2Co20v thin films prepared by pulsed laser deposition on LaA1Oa （001）. Both the electric resistivity p and the seebeck coefficient S of the film exhibit an increasing trend with the temperature from 300 K-1000 K and reach up to 4.8 m. cm and 202 V/K at 980 K, resulting in a power factor of 0.85 mW/mK which are comparable to those of the single crystalline samples. A small polaron hopping conduction can be responsible for the conduction mechanism of the film at high temperature. The results demonstrate that the Bi2Sr2Co2Oy thin film has potential application has high temperature thin film thermoelectric devices,     

利用脉冲激光沉积技术在双轴织构的Ni基带上外延CeO2薄膜

利用脉冲激光沉积技术在氢还原气氛下成功地在双轴织构的Ni基带上外延了高质量的CeO₂薄膜. x射线衍射θ—２θ扫描和ω扫描结果表明，CeO₂薄膜在Ni基带上呈c轴方向生长，存在很强的平面外织构；极图和φ扫描显示它具有良好的平面内织构. Ni基片上织构的CeO₂薄膜为进一步在其上外延高质量的YBa₂Cu₃O_7-x超导薄膜提供了很好的模板. 关键词： 双轴织构的Ni基带 2薄膜')" href="#">CeO₂薄膜 脉冲激光沉积     

VO2-WO3 nanocomposite thin films synthesized by pulsed laser deposition technique

Pure VO₂ and VO₂-WO₃ composite thin films were grown on quartz substrate by pulsed laser deposition (PLD) technique. The influence of varying WO₃ molar concentration in the range from x = 0.0 to x = 0.4 on structural, electrical and optical properties of VO₂-WO₃ nanocomposite thin films has been systematically investigated. X-ray diffraction studies reveal the single crystalline monoclinic VO₂ phase (m-VO₂) up to 10% of WO₃ content whereas both m-VO₂ as well as h-WO₃ (hexagonal WO₃) phases were present at higher WO₃ content (0.2 ≤ x ≤ 0.4). Optical transmittance spectra of the films showed blue shift in the absorption edge with increase in WO₃ content. Temperature dependence of resistivity (R-T) measurements indicates significant variation in metal-insulator transition temperature, width of the hysteresis, and shape of the hysteresis curve. Cyclic Voltammetry measurements were performed on VO₂-WO₃ thin films. A direct correlation between V/W ratio and structure-property relationship was established. The present investigations reveal that doping of WO₃ in VO₂ is effective to increase the optical transmittance and to reduce the semiconductor to metal phase transition temperature close to room temperature.     

Synthesis and properties of silicon dioxide films prepared by pulsed laser deposition using ceramic SiO2 target

Silicon dioxide (SiO₂) thin films were deposited on BK7 substrates by pulsed laser deposition (PLD) method using ceramic SiO₂ targets (C-SiO₂-Ts), which was sintered by solid state sintering. The reason for using C-SiO₂-T instead of the silicon target is to reduce the oxygen-deficiency phenomenon in deposited SiO₂ thin films. The influence of substrate-temperatures, oxygen-pressures and oxygen-plasma-assistance on the properties of synthesized films was studied. X-ray diffraction, atomic force microscopy, ultraviolet–visible–near-infrared scanning spectrophotometry were used to characterize the crystallinity, morphology and optical properties of deposited films. Results show that the root-mean-square roughness of films increased with the increase of oxygen-pressure, substrate-temperature and with the employment of oxygen-plasma. The transmittance of films increased with the increase of oxygen-pressure and decreased with the increase of substrate-temperature and with the employment of oxygen-plasma. Stoichiometric SiO₂ thin film with high optical quality was synthesized at room-temperature and 20 Pa oxygen-pressure using C-SiO₂-T.     

Pulsed laser deposition of Bi2Te3 thermoelectric films

Bi₂Te₃ is one of the most used materials for thermoelectric applications at ambient temperature. An improvement of thermoelectric performances through a suitable modification of electron and phonon transport mechanisms is predicted for low dimensional or nanostructured systems, but this requires a control of the material structure down to the nanoscale. We show that pulsed laser deposition provides control on film composition, phase and structure, necessary for a comprehension of the relationship between structure and thermoelectric properties. We have explored the role of deposition temperature, background inert gas type and pressure, laser fluence and target-to-substrate distance and we found the experimental condition ranges to obtain crystalline films containing the Bi₂Te₃ phase only, by comparing energy dispersive X-ray spectroscopy, Raman spectroscopy and X-ray diffraction analysis. Variations of substrate temperature and deposition gas pressure prove to be crucial also for the control of film morphology and crystallinity. Substrate type has no influence on film stoichiometry and crystallinity, but highly oriented growth can be achieved on mica due to van der Waals epitaxy.     

脉冲激光沉积温度及氧压对Bi2Sr2Co2Oy热电薄膜晶体结构与电输运性能的影响

利用脉冲激光沉积技术在c-Al₂O₃单晶基片上制备了Bi₂Sr₂Co₂O_y热电薄膜并研究了沉积温度和氧压对薄膜晶体结构及电输运性能的影响.在最佳沉积条件下制备的单相、c轴取向的Bi₂Sr₂Co₂O_y薄膜的室温电阻率ρ和塞贝克系数S分别为2.9mΩ/cm和110μupV/K,其功率因子S²/ρ好于在单晶样品上得到的值.此外,该薄膜在低温下表现出较强的负磁阻效应,在2K,9T时达到了40%.     

Structural and electrical properties of lithium manganese oxide thin films grown by pulsed laser deposition

LiMn₂O₄ thin films were deposited by reactive pulsed laser deposition technique and studied the microstructural and electrical properties of the films. The LiMn₂O₄ thin films deposited in an oxygen partial pressure of 100 mTorr and at a substrate temperature of 573 K from a lithium rich target were found to be nearly stoichiometric. The films exhibited predominantly (111) orientation representing the cubic spinel structure with Fd3m symmetry. The intensity of (111) peak increased and a slight shift in the peak position was observed with the increase of substrate temperature. The lattice parameter increased from 8.117 to 8.2417 Å with the increase of substrate temperature from 573 to 873 K. The electrical conductivity of the films is observed to be a strong function of temperature. The evaluated activation energy for the films deposited at 873 K is 0.64 eV.     

Visible-light photocatalytic activity of nitrogen-doped TiO2 thin film prepared by pulsed laser deposition

Nitrogen-doped titanium dioxide (TiO_2−xN_x) thin films have been prepared by pulse laser deposition on quartz glass substrates by ablated titanium dioxide (rutile) target in nitrogen atmosphere. The x value (nitrogen concentration) is 0.567 as determined by X-ray photoelectron spectroscopy measurements. UV-vis spectroscopy measurements revealed two characteristic deep levels located at 1.0 and 2.5 eV below the conduction band. The 1.0 eV level is attributable to the O vacancy state and the 2.5 eV level is introduced by N doping, which contributes to narrowing the band-gap by mixing with the O2p valence band. The enhanced degradation efficiency in a broad visible-light range was observed from the degradation of methylene blue and methylene orange by the TiO_2−xN_x film.     

Influence of deposition temperature on the structural and morphological properties of Be3N2 thin films grown by reactive laser ablation

Be₃N₂ thin films have been grown on Si(1 1 1) substrates using the pulsed laser deposition method at different substrate temperatures: room temperature (RT), 200 °C, 400 °C, 600 °C and 700 °C. Additionally, two samples were deposited at RT and were annealed after deposition in situ at 600 °C and 700 °C. In order to obtain the stoichiometry of the samples, they have been characterized in situ by X-ray photoelectron (XPS) and reflection electron energy loss spectroscopy (REELS). The influence of the substrate temperature on the morphological and structural properties of the films was investigated using scanning electron microscopy (SEM), atomic force microscopy (AFM) and X-ray diffraction (XRD). The results show that all prepared films presented the Be₃N₂ stoichiometry. Formation of whiskers with diameters of 100-200 nm appears at the surface of the films prepared with a substrate temperature of 600 °C or 700 °C. However, the samples grown at RT and annealed at 600 °C or 700 °C do not show whiskers on the surface. The average root mean square (RMS) roughness and the average grain size of the samples grown with respect the substrate temperature is presented. The films grown with a substrate temperature between the room temperature to 400 °C, and the sample annealed in situ at 600 °C were amorphous; while the αBe₃N₂ phase was presented on the samples with a substrate temperature of 600 °C, 700 °C and that deposited with the substrate at RT and annealed in situ at 700 °C.     

蓝宝石衬底SnO2:Sb薄膜的制备及结构和光致发光性质

用射频磁控溅射法在蓝宝石(0001)衬底上制备出锑掺杂的氧化锡(SnO₂:Sb)薄膜.对制备薄膜的结构和发光性质进行了研究.制备样品为多晶薄膜，具有纯SnO₂的四方金红石结构.室温条件下对样品进行光致发光测量，在334 nm附近观测到紫外发射峰，并对SnO₂:Sb的光致发光机制进行了研究.     

Structural and optical properties of pulsed laser deposited SrBi2Nb2O9 thin films

SrBi₂Nb₂O₉ (SBN) thin films were prepared on fused quartz substrates at room temperature by pulsed laser deposition. The influence of deposition parameters such as target-to-substrate distance, oxygen pressure and annealing temperature on film crystallization behavior was investigated by X-ray diffraction. Results indicated that the films grown at the optimum processing conditions have polycrystalline structure with a single layered perovskite phase. The optical transmittance of the films prepared at various oxygen pressures was measured in the wavelength range 200–900 nm using UV–vis spectrophotometer. The results showed that there is a red shift in the optical absorption edge with a rise in the oxygen pressure. Refractive index as a function of wavelength and optical band gap of the films were determined from the optical transmittance spectra. The results indicated that the refractive index increases with increasing oxygen pressure at the same incident light wavelength, while the band gap reduces from 4.13 to 3.88 eV. It may be attributed to an increase in packing density and grain size, and decrease in oxygen defects.     

Femtosecond pulsed laser deposition of nanostructured TiO2 films

Nanostructured deposits of TiO₂ were grown on Si (1 0 0) substrates by laser ablating a TiO₂ sintered target in vacuum or in oxygen using a Ti:sapphire laser delivering 80 fs pulses. The effect of the laser irradiation wavelength on the obtained nanostructures, was investigated using 800, 400 and 266 nm at different substrate temperatures and pressures of oxygen. The composition of the deposits was characterized using X-ray photoelectron spectroscopy (XPS) and the surface morphology was studied by environmental scanning electron microscopy (ESEM) and atomic force microscopy (AFM). Deposits are absent of microscopic droplets in all conditions explored. The best deposits, constituted by nanoparticles of an average diameter of 30 nm with a narrow size distribution, were obtained at the shorter laser wavelength of 266 nm under vacuum at substrate room temperature.     

Substrate effects on the oxygen gas sensing properties of SnO2/TiO2 thin films

In this study, SnO₂/TiO₂ thin films are fabricated on SiO₂/Si and Corning glass 1737 substrates using a R.F. magnetron sputtering process. The gas sensing properties of these films under an oxygen atmosphere with and without UV irradiation are carefully examined. The surface structure, morphology, optical transmission characteristics, and chemical compositions of the films are analyzed by atomic force microscopy, scanning electron microscopy and PL spectrometry. It is found that the oxygen sensitivity of the films deposited on Corning glass 1737 substrates is significantly lower than that of the films grown on SiO₂/Si substrates. Therefore, the results suggest that SiO₂/Si is an appropriate substrate material for oxygen gas sensors fabricated using thin SnO₂/TiO₂ films.     

Structural, optical and magnetic properties of Nd-doped BiFeO3 thin films prepared by pulsed laser deposition

Nd-doped BiFeO₃ thin films were grown by pulsed laser deposition on quartz substrate and their structural, optical and magnetic properties have been studied. X-ray diffraction analysis revealed that Nd addition caused structural distortion even with 5% of Nd concentration, additional secondary phase appeared in all samples but its intensity was greatly reduced with Nd addition. Doping-induced variations in texture and structure modifying both magnetic and optical properties of BiFeO₃ thin films. The energy band gap decreases while the refractive index increases with addition of Nd³⁺ in BiFeO₃ for Bi³⁺. These variations in energy band gap and refractive index have been explained on the basis of density of states and increase in disorders in the system. All the samples were found to exhibit ferromagnetism at room temperature and the saturation magnetization increases with the increase in structural distortion with addition of Nd. Finally, Nd-doping modifies the physical properties of BiFeO₃ in comparison to undoped BiFeO₃ thin films.     

Influence of substrate temperature on structures and dielectric properties of pyrochlore Bi1.5Zn1.0Nb1.5O7 thin films prepared by pulsed laser deposition

The influence of substrate temperature on structural and dielectric properties of cubic pyrochlore Bi_1.5Zn_1.0Nb_1.5O₇ (BZN) thin films prepared by pulsed laser deposition process has been investigated. BZN thin films were deposited on Pt/Ti/SiO₂/Si(1 0 0) substrate and in situ annealed at 700 °C. The results indicate that the substrate temperature has a significant effect on the structural and dielectric properties of BZN thin films. The films exhibit a cubic pyrochlore structure in the substrate temperature range from 550 °C to 700 °C and at the annealing temperature of 700 °C. With further increase of substrate temperature to 750 °C, the phases of Bi₂O₃, BiNbO₄ and Bi₅Nb₃O₁₅ can be detected in the XRD pattern due to the Zn loss. The dielectric constant and loss tangent of the films deposited at 650 °C are 192 and 6 × 10⁻⁴ at 10 kHz, respectively. The tunability is 10% at a dc bias field of 0.9 MV/cm.     

LiFePO4 thin films grown by pulsed laser deposition: Effect of the substrate on the film structure and morphology

Well crystallized and homogeneous LiFePO₄/C (LFPO) thin films have been grown by pulsed laser deposition (PLD). The targets were prepared by the sol-gel process at 600 °C. The structure of the polycrystalline powders was analyzed with X-ray powder diffraction (XRD) data. The XRD patterns were indexed having a single phase olivine structure (Pnma). LFPO thin films have been deposited on three different substrates: aluminum (Al), stainless steel (SS) and silicon (Si) by pulsed laser deposition (PLD). The structure of the films was analyzed by X-ray diffraction (XRD), Raman spectroscopy, scanning electron microscopy (SEM), transmission electron microscopy (TEM) and atomic force microscopy (AFM). It is found that the crystallinity of the thin films depends on the substrate temperature which was set at 500 °C. When annealed treatments were used, secondary phases were found, so, one step depositions at 500 °C were made.Stainless steel is demonstrated to be the best choice to act as substrate for phosphate deposition. LiFePO₄ thin films grown on stainless steel plates exhibited the presence of carbon, inducing a slight conductivity enhancement that makes these films promising candidates as one step produced cathodes in Li-ion microbatteries.     

Effect of deposition temperature on orientation and electrical properties of (K0.5Na0.5)NbO3 thin films by pulsed laser deposition

Lead-free ferroelectric K_0.5Na_0.5NbO₃ (KNN) thin films have been prepared on Pt/TiO₂/SiO₂/Si substrates by pulsed laser deposition process. The structures, crystal orientations and electrical properties of thin films have been investigated as a function of deposition temperature from 680 °C to 760 °C. It is found that the deposition temperature plays an important role in the structures, crystal orientations and electrical properties of thin films. The crystallization of thin films improves with increasing deposition temperature. The thin film deposited at 760 °C exhibits strong (0 0 1) preferential orientation, large dielectric constant of 930 and the remnant polarization of 8.54 μC/cm².     

Investigation of transmittance property of Palladium thin films fabricated by pulsed laser deposition with polarization using single layer model

In this paper the structure, morphology and optical properties of Pd thin films deposited on glass substrate by pulse laser deposition technique at two different substrate temperatures have been investigated. The fabricated films were characterized by various methods such as XRD, AFM, and UV-vis-NIR spectroscopy. The influence of surface roughness and angle of incidence with p polarization was investigated experimentally by optical property of palladium (Pd) thin films of two different thicknesses and rms roughness from transmission measurement in the visible spectral range. It has been shown that the experimental transmittance spectra agree well with their theoretical values for absorbing Pd thin film. The transmittance of thin film increases with increase in incident angle for the same sample.