Fabrication of NiC/MoC/NiMoO4 Heterostructured Nanorod Arrays as Stable Bifunctional Electrocatalysts for Efficient Overall Water Splitting

Developing noble‐metal‐free, earth‐abundant, highly active, and stable electrocatalysts with high efficiency for both hydrogen and oxygen evolution reactions is of great importance for the development of overall water‐splitting devices, but still remains a challenging issue. Herein, a 3D heterostructured NiC/MoC/NiMoO₄ electrocatalyst was prepared through a facile synthetic procedure. The electrocatalyst shows a superior catalytic activity and stability toward the hydrogen and oxygen evolution reactions. The optimized NiC/MoC/NiMoO₄ catalyst presents low overpotentials of 68 and 280 mV to reach a current density of 10 mA cm^?2 in 1.0 m KOH for the hydrogen and oxygen evolution reactions, respectively. Assembled as an electrolyzer for overall water splitting, such a heterostructure shows quite a low cell voltage of 1.52 V at 10 mA cm^?2 and remarkable stability for more than 20 h. This work provides a facile but efficient approach for the design and preparation of highly efficient bifunctional and self‐supported heterostructured electrocatalysts that can serve as promising candidates in electrochemical energy storage and conversion.     

Efficient and Stable MoS2/CdSe/NiO Photocathode for Photoelectrochemical Hydrogen Generation from Water

A novel CdSe/NiO heteroarchitecture was designed, prepared, and used as a photocathode for hydrogen generation from water. The composite films were structurally, optically, and photoelectrochemically characterized. The deposition of CdSe on the NiO film enhanced light harvesting in the visible‐light region and photoelectrochemical properties. Moreover, the CdSe/NiO photoelectrode showed superior stability both in nitrogen‐saturated and air‐saturated neutral environments. The CdSe/NiO photoelectrode after MoS₂ modification retained the stability of the CdSe/NiO electrode and exhibited higher photocatalytic and photoelectrochemical performances than the unmodified CdSe/NiO electrode. In pH 6 buffer solution, an average hydrogen‐evolution rate of 0.52 μmol h^?1 cm^?2 at ?0.131 V (versus reversible hydrogen electrode, RHE) was achieved on a MoS₂/CdSe/NiO photocathode, with almost 100 % faradaic efficiency.     

NixCo3‐xO4 Nanoneedle Arrays Grown on Ni Foam as an Efficient Bifunctional Electrocatalyst for Full Water Splitting

Developing highly active, stable and robust electrocatalysts based on earth‐abundant elements for oxygen evolution reaction (OER) and hydrogen evolution reaction (HER) is important for many renewable energy conversion processes. Herein, Ni_xCo_3‐xO₄ nanoneedle arrays grown on 3D porous nickel foam (NF) was synthesized as a bifunctional electrocatalyst with OER and HER activity for full water splitting. Benefiting from the advantageous structure, the composite exhibits superior OER activity with an overpotential of 320 mV achieving the current density of 10 mA cm^?2. An exceptional HER activity is also acquired with an overpotential of 170 mV at the current density of 10 mA cm^?2. Furthermore, the catalyst also shows the superior activity and stability for 20 h when used in the overall water splitting cell. Thus, the hierarchical 3D structure composed of the 1D nanoneedle structure in Ni_xCo_3‐xO₄/NF represents an avenue to design and develop highly active and bifunctional electrocatalysts for promising energy conversion.     

Selenium‐Enriched Nickel Selenide Nanosheets as a Robust Electrocatalyst for Hydrogen Generation

To address the urgent need for clean and sustainable energy, the rapid development of hydrogen‐based technologies has started to revolutionize the use of earth‐abundant noble‐metal‐free catalysts for the hydrogen evolution reaction (HER). Like the active sites of hydrogenases, the cation sites of pyrite‐type transition‐metal dichalcogenides have been suggested to be active in the HER. Herein, we synthesized electrodes based on a Se‐enriched NiSe₂ nanosheet array and explored the relationship between the anion sites and the improved hydrogen evolution activity through theoretical and experimental studies. The free energy for atomic hydrogen adsorption is much lower on the Se sites (0.13 eV) than on the Ni sites (0.87 eV). Notably, this electrode benefits from remarkable kinetic properties, with a small overpotential of 117 mV at 10 mA cm^?2, a low Tafel slope of 32 mV per decade, and excellent stability. Control experiments showed that the efficient conversion of H⁺ into H₂ is due to the presence of an excess of selenium in the NiSe₂ nanosheet surface.     

In Situ Growth of Ultrafine Pt Nanoparticles onto Hierarchical Co3O4 Nanosheet-Assembled Microflowers for Efficient Electrocatalytic Hydrogen Evolution

The development of Pt-based electrocatalysts with high Pt utilization efficiency toward the hydrogen evolution reaction (HER) is of great significance for the future sustainable hydrogen economy. For rational design of high-performance HER electrocatalyst, the simultaneous consideration of both thermodynamic and kinetic aspects remains greatly challenging. Herein, a simple template-derived strategy is demonstrated for the in situ growth of ultrafine Pt nanoparticles onto Co₃O₄ nanosheet-assembled microflowers (abbreviated as Pt/Co₃O₄ microflowers hereafter) by using the pre-fabricated PtCo-based Hofmann coordination polymer as reactive templates. The elaborate preparation of such intriguing hierarchical architecture with well-dispersed tiny Pt nanoparticles, abundant metal/oxide heterointerfaces and open configuration endows the formed Pt/Co₃O₄ microflowers with high Pt utilization efficiency, rich active sites, lowered energy barrier for water dissociation and expedited reaction kinetics. Consequently, the Pt/Co₃O₄ microflowers exhibit superior HER activity with a relatively low overpotential of 34 mV to deliver a current density of 10 mA cm⁻², small Tafel slope (34 mV dec⁻¹) and outstanding electrochemical stability, representing an attractive electrocatalyst for practical water splitting. What's more, our concept of in situ construction of metal/oxide heterointerfaces may provide a new opportunity to design high-performance electrocatalysts for a variety of applications.     

Quercetin 2,4‐Dioxygenase Activates Dioxygen in a Side‐On O2–Ni Complex

Quercetin 2,4‐dioxygenase (quercetinase) from Streptomyces uses nickel as the active‐site cofactor to catalyze oxidative cleavage of the flavonol quercetin. How this unusual active‐site metal supports catalysis and O₂ activation is under debate. We present crystal structures of Ni‐quercetinase in three different states, thus providing direct insight into how quercetin and O₂ are activated at the Ni²⁺ ion. The Ni²⁺ ion is coordinated by three histidine residues and a glutamate residue (E⁷⁶) in all three states. Upon binding, quercetin replaces one water ligand at Ni and is stabilized by a short hydrogen bond through E⁷⁶, the carboxylate group of which rotates by 90°. This conformational change weakens the interaction between Ni and the remaining water ligand, thereby preparing a coordination site at Ni to bind O₂. O₂ binds side‐on to the Ni²⁺ ion and is perpendicular to the C2?C3 and C3?C4 bonds of quercetin, which are cleaved in the following reaction steps.     

Formation of the Ni–CrOx/MgO and Ni/MgO Catalysts for Carbon Dioxide Reforming of Methane

Temperature-programmed reduction by hydrogen, temperature-programmed desorption of O₂, local X-ray spectral analysis, and scanning electron microscopy are used to study redox processes occurring on the Ni–Cr₂O₃/MgO and Ni/MgO catalysts for carbon dioxide reforming of methane. The reduction of Ni/MgO leads to the formation of nickel clusters distributed over the surface of MgO. During the reduction of NiO–Cr₂O₃/MgO, chromates are transformed into chromites, and then nickel is formed by the reduction of spinel NiCr₂O₄. Reoxidation leads to the oxidized structures NiO, NiCr₂O₄, and NiCrO₄.     

Towards Long‐Term Photostability of Nickel Hydroxide/BiVO4 Photoanodes for Oxygen Evolution Catalysts via In Situ Catalyst Tuning

Increasing long‐term photostability of BiVO₄ photoelectrode is an important issue for solar water splitting. The NiOOH oxygen evolution catalyst (OEC) has fast water oxidation kinetics compared to the FeOOH OEC. However, it generally shows a lower photoresponse and poor stability because of the more substantial interface recombination at the NiOOH/BiVO₄ junction. Herein, we utilize a plasma etching approach to reduce both interface/surface recombination at NiOOH/BiVO₄ and NiOOH/electrolyte junctions. Further, adding Fe²⁺ into the borate buffer electrolyte alleviates the active but unstable character of etched‐NiOOH/BiVO₄, leading to an outstanding oxygen evolution over 200 h. The improved charge transfer and photostability can be attributed to the active defects and a mixture of NiOOH/NiO/Ni in OEC induced by plasma etching. Metallic Ni acts as the ion source for the in situ generation of the NiFe OEC over long‐term durability.     

Evaluation of cation influence on the formation of M(II)Cr2O4 during the thermal decomposition of mixed carboxylate type precursors

This paper reports an investigation regarding the influence of the cation M(II) (M = Zn, Ni, Mg) on the formation of MCr₂O₄ by thermal decomposition of the corresponding M(II),Cr(III)-carboxylates (precursors) obtained by redox reaction between the corresponding metal nitrates and 1,3-propanediol. The decomposition products at different temperatures have been characterized by FT-IR spectroscopy and thermal analysis. Thus, we have evidenced that by thermal decomposition of the studied precursors in the range 250–300 °C, different amorphous oxidic phases mixtures form depending on the nature of metalic cation: (Cr₂O_3+x + ZnO) (Cr₂O_3+x + Ni/NiO) and (Cr₂O_3+x+MgO). In case of M = Zn, around 400 °C when the transition Cr₂O_3+x to Cr₂O₃ takes place, zinc chromite nuclei form by the interaction ZnO with Cr₂O₃. In case of M = Ni, due to the partial reduction of Ni(II) at Ni(0) during the thermal decomposition of the precursor the formation of nickel chromite by the reaction NiO + Cr₂O₃ is shifted toward 500 °C, when Ni is oxidized at NiO. The thermal evolution of the mixture (MgO + CrO₃) is different due to the formation as intermediary phase of MgCrO₄, which decomposes to MgCr₂O₄ around 560 °C. In order to investigate the chromites formation mechanism, we have studied the mechanical mixtures of single oxides obtained from the corresponding carboxylates. These mixtures (MO + Cr₂O₃) have been annealed at 400, 500, and 600 °C to study the evolution of the crystalline phases. It results in the prepared mixture behaving different from the mixtures obtained by thermal decomposition of the binary M(II),Cr(III)-carboxylates, recommending our synthesis method for obtaining binary oxides.     

Heteroatom‐doped MoSe2 Nanosheets with Enhanced Hydrogen Evolution Kinetics for Alkaline Water Splitting

Electrochemical water splitting for hydrogen generation is a vital part for the prospect of future energy systems, however, the practical utilization relies on the development of highly active and earth‐abundant catalysts to boost the energy conversion efficiency as well as reduce the cost. Molybdenum diselenide (MoSe₂) is a promising nonprecious metal‐based electrocatalyst for hydrogen evolution reaction (HER) in acidic media, but it exhibits inferior alkaline HER kinetics in great part due to the sluggish water adsorption/dissociation process. Herein, the alkaline HER kinetics of MoSe₂ is substantially accelerated by heteroatom doping with transition metal ions. Specifically, the Ni‐doped MoSe₂ nanosheets exhibit the most impressive catalytic activity in terms of lower overpotential and larger exchange current density. The density functional theory (DFT) calculation results reveal that Ni/Co doping plays a key role in facilitating water adsorption as well as optimizing hydrogen adsorption. The present work paves a new way to the development of low‐cost and efficient electrocatalysts towards alkaline HER.     

乙烷氧化脱氢用Ni/Al2O3催化剂中活性镍物种前驱体（英文）

Ni/Al2O3 catalysts for oxidative dehydrogenation(ODH) of ethane were prepared by impregnation of Al2O3 with nickel acetate or nickel nitrate,and by mechanical mixing of NiO and Al2O3.The Ni-based catalysts were characterized by N2 adsorption-desorption,X-ray diffraction,diffuse reflectance UV-visible diffuse reflectance spectroscopy,and temperature-programmed reduction of hydrogen.The results showed that formation of crystalline NiO particles with a size of < 8 nm and/or non-stoichiometric NiO species in the Ni/Al2O3 catalysts led to more active species in ODH of ethane under the investigated reaction conditions.In contrast,tetrahedral Ni species present in the catalysts led to higher selectivity for ethene.Formation of large crystalline NiO particles(22-32 nm) over Ni/Al2O3 catalysts decreased the selectivity for ethene.     

A Noble‐Metal‐Free Nickel(II) Polypyridyl Catalyst for Visible‐Light‐Driven Hydrogen Production from Water

The complex [Ni(bpy)₃]²⁺ (bpy=2,2′‐bipyridine) is an active catalyst for visible‐light‐driven H₂ production from water when employed with [Ir(dfppy)₂(Hdcbpy)] [dfppy=2‐(3,4‐difluorophenyl)pyridine, Hdcbpy=4‐carboxy‐2,2′‐bipyridine‐4′‐carboxylate] as the photosensitizer and triethanolamine as the sacrificial electron donor. The highest turnover number of 520 with respect to the nickel(II) catalyst is obtained in a 8:2 acetonitrile/water solution at pH 9. The H₂‐evolution system is more stable after the addition of an extra free bpy ligand, owing to faster catalyst regeneration. The photocatalytic results demonstrate that the nickel(II) polypyridyl catalyst can act as a more effective catalyst than the commonly utilized [Co(bpy)₃]²⁺. This study may offer a new paradigm for constructing simple and noble‐metal‐free catalysts for photocatalytic hydrogen production.     

高效析氧电催化剂Co3O4@NiMn-LDH异质结构阵列的制备

我们合理设计和制备了一种新型的高性能析氧电催化剂——泡沫镍负载Co_3O_4@NiMn-LDH(层状双金属氢氧化物)三维异质结构阵列(Co_3O_4@NiMn-LDH/NF)。这种基于泡沫镍基底的三维异质结构催化剂经简单的两步水热反应即可制得。对比Co_3O_4、NiMn-LDH及传统RuO2催化剂,所制备的Co_3O_4@NiMn-LDH/NF催化剂展示出更优异的电催化析氧性能。在1 mol·L~(-1)KOH溶液中,电流密度为50 mA·cm~(-2)时的过电势仅为282 mV,塔菲尔斜率为64 mV·dec~(-1)。通过有效的界面工程设计,使异质结构陈列Co_3O_4@NiMn-LDH发挥出Co_3O_4和NiMn-LDH各自优异的电催化性能。其中,基于泡沫镍基底生长的活性组分Co_3O_4纳米线阵列作为中间核支撑结构,保持了良好的空隙率,不仅有利于暴露更多的活性位点,而且有利于电解液的扩散和气体产物的释放;而依附于Co_3O_4纳米线阵列上的NiMn-LDH异质结构纳米片层则富有更多的亲水性基团,使得活性位点更易与水结合,从而促进氧析出反应的进行。     

Metal-Organic Framework Glass Catalysts from Melting Glass-Forming Cobalt-Based Zeolitic Imidazolate Framework for Boosting Photoelectrochemical Water Oxidation

Sluggish oxygen evolution kinetics and serious charge recombination restrict the development of photoelectrochemical (PEC) water splitting. The advancement of novel metal–organic frameworks (MOFs) catalysts bears practical significance for improving PEC water splitting performance. Herein, a MOF glass catalyst through melting glass-forming cobalt-based zeolitic imidazolate framework (Co-a_gZIF-62) was introduced on various metal oxide (MO: Fe₂O₃, WO₃ and BiVO₄) semiconductor substrates coupled with NiO hole transport layer, constructing the integrated Co-a_gZIF-62/NiO/MO photoanodes. Owing to the excellent conductivity, stability and open active sites of MOF glass, Co-a_gZIF-62/NiO/MO photoanodes exhibit a significantly enhanced photoelectrochemical water oxidation activity and stability in comparison to pristine MO photoanodes. From experimental analyses and density functional theory calculations, Co-a_gZIF-62 can effectively promote charge transfer and separation, improve carrier mobility, accelerate the kinetics of oxygen evolution reaction (OER), and thus improve PEC performance. This MOF glass not only serves as an excellent OER cocatalyst on tunable photoelectrodes, but also enables promising opportunities for PEC devices for solar energy conversion.     

Hydrogen Storage and Selective,Reversible O2 Adsorption in a Metal–Organic Framework with Open Chromium(II) Sites

A chromium(II)‐based metal–organic framework Cr₃[(Cr₄Cl)₃(BTT)₈]₂ (Cr‐BTT; BTT³⁻=1,3,5‐benzenetristetrazolate), featuring coordinatively unsaturated, redox‐active Cr²⁺ cation sites, was synthesized and investigated for potential applications in H₂ storage and O₂ production. Low‐pressure H₂ adsorption and neutron powder diffraction experiments reveal moderately strong Cr–H₂ interactions, in line with results from previously reported M‐BTT frameworks. Notably, gas adsorption measurements also reveal excellent O₂/N₂ selectivity with substantial O₂ reversibility at room temperature, based on selective electron transfer to form Cr^III superoxide moieties. Infrared spectroscopy and powder neutron diffraction experiments were used to confirm this mechanism of selective O₂ binding.     

Hydrogen Storage and Selective,Reversible O2 Adsorption in a Metal–Organic Framework with Open Chromium(II) Sites

A chromium(II)‐based metal–organic framework Cr₃[(Cr₄Cl)₃(BTT)₈]₂ (Cr‐BTT; BTT^3?=1,3,5‐benzenetristetrazolate), featuring coordinatively unsaturated, redox‐active Cr²⁺ cation sites, was synthesized and investigated for potential applications in H₂ storage and O₂ production. Low‐pressure H₂ adsorption and neutron powder diffraction experiments reveal moderately strong Cr–H₂ interactions, in line with results from previously reported M‐BTT frameworks. Notably, gas adsorption measurements also reveal excellent O₂/N₂ selectivity with substantial O₂ reversibility at room temperature, based on selective electron transfer to form Cr^III superoxide moieties. Infrared spectroscopy and powder neutron diffraction experiments were used to confirm this mechanism of selective O₂ binding.     

Thermodynamic possibilities and constraints of pure hydrogen production by a chromium,nickel, and manganese-based chemical looping process at lower temperatures

The reduction of chromium, nickel, and manganese oxides by hydrogen, CO, CH₄, and model syngas (mixtures of CO + H₂ or H₂ + CO + CO₂) and oxidation by water vapor has been studied from the thermodynamic and chemical equilibrium point of view. Attention was concentrated not only on the convenient conditions for reduction of the relevant oxides to metals or lower oxides at temperatures in the range 400–1000 K, but also on the possible formation of soot, carbides, and carbonates as precursors for the carbon monoxide and carbon dioxide formation in the steam oxidation step. Reduction of very stable Cr₂O₃ to metallic Cr by hydrogen or CO at temperatures of 400–1000 K is thermodynamically excluded. Reduction of nickel oxide (NiO) and manganese oxide (Mn₃O₄) by hydrogen or CO at such temperatures is feasible. The oxidation of MnO and Ni by steam and simultaneous production of hydrogen at temperatures between 400 and 1000 K is a difficult step from the thermodynamics viewpoint. Assuming the Ni—NiO system, the formation of nickel aluminum spinel could be used to increase the equilibrium hydrogen yield, thus, enabling the hydrogen production via looping redox process. The equilibrium hydrogen yield under the conditions of steam oxidation of the Ni—NiO system is, however, substantially lower than that for the Fe—Fe₃O₄ system. The system comprising nickel ferrite seems to be unsuitable for cyclic redox processes. Under strongly reducing conditions, at high CO concentrations/partial pressures, formation of nickel carbide (Ni₃C) is thermodynamically favored. Pressurized conditions during the reduction step with CO/CO₂ containing gases enhance the formation of soot and carbon-containing compounds such as carbides and/or carbonates.     

Surface Functionalization of g‐C3N4: Molecular‐Level Design of Noble‐Metal‐Free Hydrogen Evolution Photocatalysts

A stable noble‐metal‐free hydrogen evolution photocatalyst based on graphite carbon nitride (g‐C₃N₄) was developed by a molecular‐level design strategy. Surface functionalization was successfully conducted to introduce a single nickel active site onto the surface of the semiconducting g‐C₃N₄. This catalyst family (with less than 0.1 wt % of Ni) has been found to produce hydrogen with a rate near to the value obtained by using 3 wt % platinum as co‐catalyst. This new catalyst also exhibits very good stability under hydrogen evolution conditions, without any evidence of deactivation after 24 h.     

Ni3N as an Active Hydrogen Oxidation Reaction Catalyst in Alkaline Medium

Hydroxide‐exchange membrane fuel cells can potentially utilize platinum‐group‐metal (PGM)‐free electrocatalysts, offering cost and scalability advantages over more developed proton‐exchange membrane fuel cells. However, there is a lack of non‐precious electrocatalysts that are active and stable for the hydrogen oxidation reaction (HOR) relevant to hydroxide‐exchange membrane fuel cells. Here we report the discovery and development of Ni₃N as an active and robust HOR catalyst in alkaline medium. A supported version of the catalyst, Ni₃N/C, exhibits by far the highest mass activity and break‐down potential for a PGM‐free catalyst. The catalyst also exhibits Pt‐like activity for hydrogen evolution reaction (HER) in alkaline medium. Spectroscopy data reveal a downshift of the Ni d band going from Ni to Ni₃N and interfacial charge transfer from Ni₃N to the carbon support. These properties weaken the binding energy of hydrogen and oxygen species, resulting in remarkable HOR activity and stability.     

Ni-based overall water splitting electrocatalysts prepared via laser-ablation-in-liquids combined with electrophoretic deposition

Synthesis of fine nanoparticles (NPs) with surface-active sites free from undesired chemical residues is the key to drive chemical kinetics. However, active sites of chemically produced NPs are limited because of the adsorption of chemical residues. Therefore, the development of a physical approach to produce NPs having surfaces free from chemical contamination is imperative to electrochemical water splitting. Here, we present a physical top-down approach where suspended NPs generated via pulsed laser ablation in liquids are electrophoretic deposited on a substrate to fabricate ready-to-use electrocatalysts for overall water splitting. Three different laser pulse energies were used to ablate Ni plate in pure water or aqueous media of 1M polyethylene glycol (PEG) to produce six different colloidal solutions of NPs. The samples produced in the water at higher laser pulse energies have Ni/NiO phase in abundance, while those produced in PEG dominate Ni/Ni(OH)₂ phase. Among all the electrophoretically fabricated electrocatalysts, Ni-Di-70 is the best performer in overall water splitting, while Ni-P-30 is the worse. We believe that the selective adsorption of H1, responsible for hydrogen evolution reaction, at Ni sites, and OH^? ions, oxygen evolution intermediate, at NiO sites of Ni/NiO interface increase hydrogen and oxygen generation performances of Ni-Di-70 sample. The poor performance of PEG produced electrocatalysts is attributed to the combined effects of the formation of a larger assembly of NPs and adsorption of PEG molecules on the active sites.