木质纤维素酶解糖化*

纤维素水解转化为可发酵糖工艺是纤维素乙醇炼制过程中至关重要的环节。酶法水解工艺具有条件温和、副产物少、环境友好等特点,因而受到广泛重视。目前许多学者已针对如何提高木质纤维素酶解效率、降低纤维素酶成本等问题,开展了多种化学、生物技术及工艺耦合的研究。本文综述了近几年木质纤维素酶解领域取得的最新工艺进展和理论研究成果,对原料预处理、多酶复配优化、酶脱附与重复利用、工艺耦合、高固液比反应等方面的研究情况进行了总结,同时展望了木质纤维素酶解工艺的未来发展方向。     

The structural changes in crystalline cellulose and effects on enzymatic digestibility

The enzymatic hydrolysis of cellulose I achieves almost complete digestion when sufficient enzyme loading as much as 20 mg/g-substrate is applied. However, the yield of digestion reaches the limit when the enzyme dosage is decreased to 2 mg/g-substrate. Therefore, we have performed three pretreatments such as mercerization, dissolution into phosphoric acid and EDA treatment. Transformation into cellulose II hydrate by mercerization and dissolution into phosphoric acid were not sufficient because substrate changed to highly crystalline structure during saccharification. On the other hand, in the case of crystalline conversion of cellulose I to III_I by EDA, almost perfect digestion was achieved even in enzyme loading as small as 0.5 mg/g-substrate, furthermore, hydrolyzed residue was typical cellulose I. The structural analysis of substrate after saccharification provides an insight into relationships between cellulose crystalline property and cellulase toward better enzymatic digestion.     

Nonisothermal simultaneous saccharification and fermentation for direct conversion of lignocellulosic biomass to ethanol

The enzymatic reaction in the simultaneous saccharification and fermentation (SSF) is operated at a temperature much lower than its optimum level. This forces the enzyme activity to be far below its potential, consequently raising the enzyme requirement. To alleviate this problem, a nonisothermal simultaneous saccharification and fermentation process (NSSF) was investigated. The NSSF is devised so that saccharification and fermentation occur simultaneously, yet in two separate reactors that are maintained at different temperatures. Lignocellulosic biomass is retained inside a column reactor and hydrolyzed at the optimum temperature for the enzymatic reaction (50°C). The effluent from the column reactor is recirculated through a fermenter, which runs at its optimum temperature (20-30°C). The cellulase enzyme activity is increased by a factor of 2-3 when the hydrolysis temperature is raised from 30 to 50°C. The NSSF process has improved the enzymatic reaction in the SSF to the extent that it reduces the overall enzyme requirement by 30-40%. The effect of temperature on β-glucosidase activity was the most significant among the individual cellulase compounds. Both ethanol yield and productivity in the NSSF are substantially higher than those in the SSF at the enzyme loading of 5 IFPU/g glucan. With 10 IFPU/g glucan, improvement in productivity was more discernible for the NSSF. The terminal yield attainable in 4 d with the SSF was reachable in 40 h with the NSSF.     

Empirical Evaluation of Inhibitory Product, Substrate, and Enzyme Effects During the Enzymatic Saccharification of Lignocellulosic Biomass

The cellulose hydrolysis kinetics during batch enzymatic saccharification are typified by a rapid initial rate that subsequently decays, resulting in incomplete conversion. Previous studies suggest that changes associated with the solution, substrate, or enzymes may be responsible. In this work, kinetic experiments were conducted to determine the relative magnitude of these effects. Pretreated corn stover (PCS) was used as a lignocellulosic substrate likely to be found in a commercial saccharification process, while Avicel and Kraft lignin were used to create model substrates. Glucose inhibition was observed by spiking the reaction slurry with glucose during initial-rate experiments. Increasing the glucose concentration from 7 to 48 g/L reduced the cellulose conversion rate by 94%. When product sugars were removed using ultrafiltration with a 10 kDa membrane, the glucose-based conversion increased by 9.5%. Reductions in substrate reactivity with conversion were compared directly by saccharifying PCS and Avicel substrates that had been pre-reacted to different conversions. Reaction of substrate with a pre-conversion of 40% resulted in about 40% reduction in the initial rate of saccharification, relative to fresh substrate with identical cellulose concentration. Overall, glucose inhibition and reduced substrate reactivity appear to be dominant factors, whereas minimal reductions of enzyme activity were observed.     

Effects of hemicellulose and lignin on enzymatic hydrolysis of cellulose from dairy manure

This study focused on the effect of hemicellulose and lignin on enzymatic hydrolysis of dairy manure and hydrolysis process optimization to improve sugar yield. It was found that hemicellulose and lignin in dairy manure, similar to their role in other lignocellulosic material, were major resistive factors to enzymatic hydrolysis and that the removal of either of them, or for best performance, both of them, improved the enzymatic hydrolysis of manure cellulose. This result combined with scanning electron microscope (SEM) pictures further proved that the accessibility of cellulose to cellulase was the most important feature to the hydrolysis. Quantitatively, fed-batch enzymatic hydrolysis of fiber without lignin and hemicellulose had a high glucose yield of 52% with respect to the glucose concentration of 17 g/L at a total enzyme loading of 1300 FPU/L and reaction time of 160 h, which was better than corresponding batch enzymatic hydrolysis.     

Ball Milling Pretreatment of Corn Stover for Enhancing the Efficiency of Enzymatic Hydrolysis

Ethanol can be produced from lignocellulosic biomass with the usage of ball milling pretreatment followed by enzymatic hydrolysis and fermentation. The sugar yields from lignocellulosic feed stocks are critical parameters for ethanol production process. The research results from this paper indicated that the yields of glucose and xylose were improved by adding any of the following dilute chemical reagents: H₂SO₄, HCl, HNO₃, CH₃COOH, HCOOH, H₃PO₄, and NaOH, KOH, Ca(OH)₂, NH₃·H₂O in the ball milling pretreatment of corn stover. The optimal enzymatic hydrolysis efficiencies were obtained under the conditions of ball milling in the alkali medium that was due to delignification. The data also demonstrated that ball milling pretreatment was a robust process. From the microscope image of ball milling-pretreated corn stover, it could be observed that the particle size of material was decreased and the fiber structure was more loosely organized. Meanwhile, the results indicate that the treatment effect of wet milling is better than that of dry milling. The optimum parameters for the milling process were ball speed of 350 r/min, solid/liquid ratio of 1:10, raw material particle size with 0.5 mm, and number of balls of 20 (steel ball, Φ = 10 mm), grinding for 30 min. In comparison with water milling process, alkaline milling treatment could increase the enzymatic hydrolysis efficiency of corn stover by 110%; and through the digestion process with the combination of xylanase and cellulase mixture, the hydrolysis efficiency could increase by 160%.     

Effects of Substrate Loading on Enzymatic Hydrolysis and Viscosity of Pretreated Barley Straw

In this study, the applicability of a “fed-batch” strategy, that is, sequential loading of substrate or substrate plus enzymes during enzymatic hydrolysis was evaluated for hydrolysis of steam-pretreated barley straw. The specific aims were to achieve hydrolysis of high substrate levels, low viscosity during hydrolysis, and high glucose concentrations. An enzyme system comprising Celluclast and Novozyme 188, a commercial cellulase product derived from Trichoderma reesei and a β-glucosidase derived from Aspergillus niger, respectively, was used for the enzymatic hydrolysis. The highest final glucose concentration, 78 g/l, after 72 h of reaction, was obtained with an initial, full substrate loading of 15% dry matter weight/weight (w/w DM). Conversely, the glucose yields, in grams per gram of DM, were highest at lower substrate concentrations, with the highest glucose yield being 0.53 g/g DM for the reaction with a substrate loading of 5% w/w DM after 72 h. The reactions subjected to gradual loading of substrate or substrate plus enzymes to increase the substrate levels from 5 to 15% w/w DM, consistently provided lower concentrations of glucose after 72 h of reaction; however, the initial rates of conversion varied in the different reactions. Rapid cellulose degradation was accompanied by rapid decreases in viscosity before addition of extra substrate, but when extra substrate or substrate plus enzymes were added, the viscosities of the slurries increased and the hydrolytic efficiencies decreased temporarily.     

Mathematical modeling of cellulose conversion to ethanol by the simultaneous saccharification and fermentation process

Ethanol, a promising alternative fuel, can be produced by the simultaneous saccharification and fermentation (SSF) of lignocellulosic biomass, which combines the enzymatic hydrolysis of cellulose to glucose and the fermentation of glucose to ethanol by yeast in a single step.

A mathematical model that depicts the kinetics of SSF has been developed based on considerations of the quality of the substrate and enzyme, and the substrate-enzyme-microorganism interactions. Critical experimentation has been performed in conjunction with multiresponse nonlinear regression analysis to determine key model parameters regarding cell growth and ethanol production. The model will be used for rational SSF optimization and scale-up.

     

Enhancement of enzymatic cellulose hydrolysis using a novel type of bioreactor with intensive stirring induced by electromagnetic field

The use of the intensive mass transfer reactor (IMTR) for enzymatic saccharification of cellulose, where the reaction mixture is intensively stirred by ferromagnetic particles (FMP), enhances the process rate and productivity drastically. The most significant enhancement of the process was observed when microcrystalline cellulose was used as a substrate. A concentration of sugars up to 5% was obtained after 1 h of cellulose hydrolysis using a cellulase activity level of 2 filter paper units (FPU)/mL (20 FPU/g substrate). In the hydrolysis of two types of industrial cellulosic wastes, the enhancement effects were less pronounced. Parameters related to the IMTR design, such as the shape, dimensions, and mass of FMP, as well as the magnetic field strength, strongly affected the process of hydrolysis. Among various kinds of FMP tested, the most efficient were found to be cylindrical particles (0.25 x 4 mm). In general, the hydrolysis rate enhanced when the magnetic field strength increased from 26,000 to 64,000 A/m. An optimal FMP loading existed at each level of the field strength. Hydrolyzates obtained in the IMTR under the action ofTrichoderma reesei andPenicillium verruculosum cellulases contained glucose and cellobiose as soluble products, cellobiose being predominant (> 50%). Only when a high level of extra Β-glucosidase was added to the IMTR (10 CBU/mL), did glucose made up more than 90% of the products. Owing to extreme shear conditions in the IMTR, significant enzyme inactivation took place.     

Enhancement of the enzymatic digestibility of waste newspaper using tween

Methods of increasing the enzymatic digestibility of waste newspaper by adding Tween (TW)-20 and 80 surfactants were investigated. Tween-series surfactants were selected because these surfactants increase cellulase activity during enzymatic hydrolysis and do not inhibit cell growth in downstream fermentation processes. When surfactant was used in a pretreatment, a benefic effect was expected in the enzymatic hydrolysis stage owing to surfactant carry-over from the pretreatment stage immediately upstream of the hydrolysis. However, because it was necessary to wash the pretreated substrate with water to remove inhibitors produced during pretreatment, no added benefit was obtained. When surfactant was used in the pretreatment only, it was found that it had a marked effect on digestibility and that this effect was higher at lower enzyme loadings. Also, TW-80 was found to be more effective than TW-20, and the addition of enzyme and TW-80 to substrate at the beginning of enzyme reaction was found to most effectively increase digestibility. When TW-80 was added into either the pretreatment stage or the hydrolysis stage the digestibilities of untreated sample increased by approx 40%, whereas an increase of only 45% was observed when TW-80 was added to both stages. These results show that the addition of surfactant to either the pretreatment or the enzymatic hydrolysis stage is sufficient to increase digestibility.     

Optimization of Saccharification and Fermentation Process in Bioethanol Production from Oil Palm Fronds

Oil Palm Frond (OPF) is one of lignocellulosic biomass, which can be utilized as raw material for bioethanol production. Bioethanol is produced as alternative energy to substitute gasoline. There are four steps in bioethanol production from OPF, i.e pretreatement, saccharification, fermentation and purification process. In this study, optimization of saccharification and fermentation process for OPF was investigated. Two methods and the variations of enzyme concentration were carried out in the saccharification and fermentation process. Separate hydrolysis and fermentation process (SHF) and simultaneous saccharification and fermentation process (SSF) were conducted to produce ethanol optimally. Variations of enzyme concentration used in this process were 10, 20, 30 and 40 FPU/g substrate. The result shows that the highest ethanol concentration can be obtained in SSF process with 30 FPU/g substrate of enzyme concentration. The process produced 59.20 g/L ethanol (95.95% yield ethanol) at 96 h of SSF process.     

Cascade Enzymatic Hydrolysis Coupling with Ultra ne Grinding Pretreatment for Sugarcane Bagasse Sacchari cation

The biorefinery process for sugarcane bagasse saccharification generally requires significant accessibility of cellulose. We reported a novel method of cascade cellulase enzymatic hydrolysis coupling with ultrafine grinding pretreatment for sugarcane bagasse saccharification. Three enzymatic hydrolysis modes including single cellulase enzymatic hydrolysis, mixed cellulase enzymatic hydrolysis, and cascade cellulase enzymatic hydrolysis were compared. The changes on the functional group and surface morphology of bagasse during cascade cellulase enzymatic hydrolysis were also examined by FT-IR and SEM respectively. The results showed that cascade enzymatic hydrolysis was the most efficient way to enhance the sugarcane bagasse sacchari cation. More than 65% of reducing sugar yield with 90.1% of glucose selectivity was achieved at 50 oC, pH=4.8 for 72 h (1200 r/min) with cellulase I of 7.5 FPU/g substrate and cellulase II of 5 FPU/g substrate.     

Statistical Optimization of Recycled-Paper Enzymatic Hydrolysis for Simultaneous Saccharification and Fermentation Via Central Composite Design

A central composite design of the response surface methodology (RSM) was employed to study the effects of temperature, enzyme concentration, and stirring rate on recycled-paper enzymatic hydrolysis. Among the three variables, temperature and enzyme concentration significantly affected the conversion efficiency of substrate, whereas stirring rate was not effective. A quadratic polynomial equation was obtained for enzymatic hydrolysis by multiple regression analysis using RSM. The results of validation experiments were coincident with the predicted model. The optimum conditions for enzymatic hydrolysis were temperature, enzyme concentration, and stirring rate of 43.1 °C, 20 FPU g⁻¹ substrate, and 145 rpm, respectively. In the subsequent simultaneous saccharification and fermentation (SSF) experiment under the optimum conditions, the highest 28.7 g ethanol l⁻¹ was reached in the fed-batch SSF when 5% (w/v) substrate concentration was used initially, and another 5% added after 12 h fermentation. This ethanol output corresponded to 77.7% of the theoretical yield based on the glucose content in the raw material.     

Use of a new membrane-reactor saccharification assay to evaluate the performance of celluloses under simulated ssf conditions

A new saccharification assay has been devised, in which a continuously buffer-swept membrane reactor is used to remove the solubilized saccharification products, thus allowing high extents of substrate conversion without significant inhibitory effects from the buildup of either cellobiose or glucose. This diafiltration saccharification assay (DSA) can, therefore, be used to obtain direct measurements of the performance of combinations of cellulase and substrate under simulated SSF conditions, without the saccharification results being complicated by factors that may influence the subsequent fermentation step. This assay has been used to compare the effectiveness of commercial and special in-house-producedTrichoderma reeSci. cellulase preparations in the saccharification of a standardized microcrystalline (Sigmacell) substrate and a dilute-acid pretreated lignocellulosic substrate. Initial results strongly suggest that enzyme preparations produced in the presence of the targeted lignocellulosic substrate will saccharify that substrate more effectively. These results call into question the widespread use of the “filter paper assay” as a reliable predictor of enzyme performance in the extensive hydrolysis of substrates that are quite different from filter paper in both physical properties and chemical composition.

     

Modeling the enzymatic hydrolysis of dilute-acid pretreated Douglas Fir

Glucose yield from the enzymatic hydrolysis of cellulose was investigated as a function of cellulase enzyme loading (7–36 filter paper units [FPU]/g cellulose) and solids concentration (7–18% total solids) for up to 72 h on dilute sulfuric-acid pretreated Douglas Fir. The saccharification was performed on whole hydrolysate with no separation or washing of the solids. Enzyme loading had a significant effect on glucose yield; solids concentration had a much smaller effect even at higher glucose concentrations. The data were used to generate an empirical model for glucose yield, and to fit parameters of a cellulose hydrolysis kinetic model. Both models could be used for economic evaluation of a separate hydrolysis and fermentation process.     

Simultaneous saccharification and fermentation of cellulosic biomass to acetic acid

Astrain of Clostridium thermoaceticum (ATCC 49707) was evaluated for its homoacetate potential. This thermophilic anaerobe best produces acetate from glucose at pH 6.0 and 59°C with a yield of 83% of theoretical. Enzyme hydrolysis of two substrates, a-cellulose and a pulp mill sludge, yielded 68% and 70% digestion, respectively. The optimum conditions for the simultaneous saccharification and fermentation (SSF) were substrate dependent: 55°C, pH 6.0 for α-cellulose, and 55°C, pH 5.5 for the pulp mill sludge. In the SSF with α-cellulose, the overall yield of acetate was strongly influenced by the enzyme loading. In a fed-batch operation of SSF with α-cellulose, an overall acetic acid yield of 60 wt% was obtained. Among the factors limiting the yields were incomplete digestion by the enzyme and the end-product inhibition. In the SSF of pulp mill sludge, inhibitors present in the sludge severely limited bacterial action. A large accumulation of glucose developed over the entire process, changing the intended SSF operation into a separate hydrolysis and fermentation operation. Despite a long lag phase of microbial growth, a terminal yield of 85% was obtained with this substrate.     

Cellulase adsorption and an evaluation of enzyme recycle during hydrolysis of steam-exploded softwood residues

The sugar yield and enzyme adsorption profile obtained during the hydrolysis of SO₂-catalyzed steam-exploded Douglas-fir and posttreated steamexploded Douglas-fir substrates were determined. After hot alkali peroxide posttreatment, the rates and yield of hydrolysis attained from the posttreated Douglas-fir were significantly higher, even at lower enzyme loadings, than those obtained with the corresponding steam-exploded Douglas-fir. The enzymatic adsorption profiles observed during hydrolysis of the two substrates were significantly different. Ultrafiltration was employed to recover enzyme in solution (supernatant) and reused in subsequent hydrolysis reactions with added, fresh substrate. These recycle findings suggested that the enzyme remained relatively active for three rounds of recycle. It is likely that enzyme recovery and reuse during the hydrolysis of posttreated softwood substrates could lead to reductions in the need for the addition of fresh enzyme during softwood-based bioconversion processes.     

Addition of Surfactants and Non-Hydrolytic Proteins and Their Influence on Enzymatic Hydrolysis of Pretreated Sugarcane Bagasse

Poly(ethylene glycol) (PEG 4000) and bovine serum albumin (BSA) were investigated with the purpose of evaluating their influence on enzymatic hydrolysis of sugarcane bagasse. Effects of these supplements were assayed for different enzymatic cocktails (Trichoderma harzianum and Penicillium funiculosum) that acted on lignocellulosic material submitted to different pretreatment methods with varying solid (25 and 100 g/L) and protein (7.5 and 20 mg/g cellulose) loadings. The highest levels of glucose release were achieved using partially delignified cellulignin as substrate, along with the T. harzianum cocktail: increases of 14 and 18 % for 25 g/L solid loadings and of 33 and 43 % for 100 g/L solid loadings were reached for BSA and PEG supplementation, respectively. Addition of these supplements could maintain hydrolysis yield even for higher solid loadings, but for higher enzymatic cocktail protein loadings, increases in glucose release were not observed. Results indicate that synergism might occur among these additives and cellulase and xylanases. The use of these supplements, besides depending on factors such as pretreatment method of sugarcane bagasse, enzymatic cocktails composition, and solid and protein loadings, may not always lead to positive effects on the hydrolysis of lignocellulosic material, making it necessary further statistical studies, according to process conditions.     

Stagewise Dilute-Acid Pretreatment and Enzyme Hydrolysis of Distillers’ Grains and Corn Fiber

Distillers’ grains and corn fiber are the coproducts of the corn dry grind and wet milling industries, respectively. Availability of distillers’ grains and corn fiber at the ethanol plant and their high levels of lignocellulosic material make these coproducts attractive feedstocks for conversion to ethanol. In this study, dilute sulfuric acid hydrolysis of these coproducts was investigated in a multistage scheme. After the completion of each pretreatment stage, the liquid substrate was separated and reused in the succeeding pretreatment stage with a fresh substrate. The substrate from each stage was also subjected to enzyme hydrolysis in a separate experiment. The sulfuric acid concentration and the substrate loading were maintained at 1.0 vol% and 15.0 wt.%, respectively, and the temperature was maintained at 120 °C in all the experiments. Experiments were also performed to study the effect of removing oil from the samples prior to the pretreatment. The highest concentration of monomeric sugars (MS) was observed when three stages of pretreatment were followed by the enzyme reaction. The enzyme hydrolysis of the three-stage pretreated dried distillers’ grains and corn fiber yielded 122.6 ± 5.8 and 184.5 ± 4.1 mg/mL of MS, respectively. The formation of inhibitory products was also monitored.     

Relatively High-Substrate Consistency Hydrolysis of Steam-Pretreated Sweet Sorghum Bagasse at Relatively Low Cellulase Loading

Sweet sorghum bagasse (SSB) was steam pretreated in the conditions of 190 °C for 5 min to assess its amenability to the pretreatment and enzymatic hydrolysis. Results showed that pretreatment conditions were robust enough to pretreat SSB with maximum of 87% glucan and 72% xylan recovery. Subsequent enzymatic hydrolysis showed that the pretreated SSB at 2% substrate consistency resulted in maximum of 70% glucan-glucose conversion. Increasing substrate consistency from 2% to 16% led to a significant reduction in glucan conversion. However, the decrease ratio of glucan-glucose conversion was the minimum when the consistency increased from 2% to 12%. When the pretreated SSB consistency of 12% was applied for hydrolysis, increase in cellulase loading from 7.5 up to 20 filter paper units (FPU)/g glucan resulted only in 14% increase in glucan-glucose conversion compared to 20% increase with cellulase loading varying from 2.5 to 7.5 FPU/g glucan. More than 10 cellobiase units (CBU)/g glucan β-glucosidase supplementation had no noticeable improvement on glucan-glucose conversion. Additionally, supplementation of xylanase was found to significantly increase glucan-glucose conversion from 50% to 80% with the substrate consistency of 12%, when the cellulase and β-glucosidase loadings were at relatively low enzyme loadings (7.5 FPU/g and 10 CBU/g glucan). It appeared that residual xylan played a critical role in hindering the ease of hydrolysis of SSB. A proper xylanase addition was suggested to achieve a high hydrolysis yield at relatively high substrate consistency with relatively low enzyme loadings.