Barrier and Mechanical Properties of Poly(caprolactone)/organoclay Nanocomposites

In this study, biodegradable poly(caprolactone) (PCL) hybrids with two types of organoclays: Cloisite 30B (30B) and Cloisite 93A (93A) have been prepared by melt mixing and their barrier performance to air permeation and mechanical properties were investigated. The hybrids of PCL/30B were found to be nanocomposites resulted from the strong interaction between organic modifier of 30B and PCL and those of PCL/93A were microcomposites. The barrier performance of PCL/30B nanocomposite film to air permeation was much more improved than pure PCL and PCL/93A microcomposites at low organoclay concentration. With the increase of organoclay content the permeability coefficient was also increased that could attributed to the extra tortuous pathway for gas permeation caused by organoclay exfoliation. The barrier behaviour of PCL/30B nanocomposites could be approximately described by a theoretical model developed for composites. The mechanical properties measurements showed that the reinforcement of organoclay 30B in nanocomposites is more significant than 93A in microcomposites. Both tensile modulus and tensile strength were increased in PCL/30B nanocomposites even at at low amount of organoclay without much loss of strain at break as compared to pure PCL. The significant improvements in both barrier and mechanical properties in PCL nanocomposites could be attributed to the fine dispersion state of organoclay 30B platelets in PCL matrix and the strong interaction between organic modifier of 30B and matrix molecules.     

Morphology, crystallization and mechanical properties of poly(ɛ-caprolactone)/graphene oxide nanocomposites

A series of nanocomposites based on poly(ε-caprolactone) (PCL) and graphene oxide (GO) were prepared by in situ polymerization. Scanning electron microscopy observation revealed not only a well dispersion of GO but also a strong interfacial interaction between GO and the PCL matrix, as evidenced by the presence of some GO nanosheets embedded in the matrix. Effects of GO nanofillers on the crystal structure, crystallization behavior and spherulitic morphology of the PCL matrix were investigated in detail. The results showed that the crystallization temperature of PCL enhanced significantly due to the presence of GO in the nanocomposites, however, the addition of GO did not affect the crystal structure greatly. Thermal stability of PCL remarkably increased with the addition of GO nanosheets, compared with that of pure PCL. Incorporation of GO greatly improved the tensile strength and Young’s modulus of PCL without a significant loss of the elongation at break.     

Click coupled graphene for fabrication of high‐performance polymer nanocomposites

An effective technique of using click coupled graphene to obtain high‐performance polymer nanocomposites is presented. Poly(ε‐caprolactone) (PCL)‐click coupled graphene sheet (GS) reinforcing fillers are synthesized by the covalent functionalization of graphene oxide with PCL, and subsequently the PCL‐GS as a reinforcing filler was incorporated into a shape memory polyurethane matrix by solution casting. The PCL‐click coupled GS has shown excellent interaction with the polyurethane matrix, and as a consequence, the mechanical properties, thermal stability, thermal conductivity, and thermo‐responsive shape memory properties of the resulting nanocomposite films could be enhanced remarkably. In particular, for polyurethane nanocomposites incorporated with 2% PCL‐GS, the breaking stress, Young's modulus, elongation‐at‐break, and thermal stability have been improved by 109%, 158%, 28%, and 71 °C, respectively. This click coupling protocol offers the possibility to fully combine the extraordinary performance of GSs with the properties of polyurethane. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2013     

Bio-Based Nanocomposites of Cellulose Acetate and Nano-Clay with Superior Mechanical Properties

Summary: Bio-based nanocomposites were manufactured by melt intercalation of nanoclays and cellulose acetate (CA) with and without plasticizer. Glycerol triacetate (triacetin) as plasticizer up to 30 mass%, and different types of organo-modified and unmodified montmorillonites (MMTs) as filler were used. X-ray diffraction (XRD), transmission electron microscopy (TEM), and scanning electron microscopy (SEM), were used to study clay dispersion, intercalation/exfoliation, and structure of the composites. XRD and TEM revealed very good dispersion and exfoliation of modified clay throughout the CA matrix. While for unmodified clay agglomeration and poor dispersion but an intercalated structure was observed. The mechanical properties of injection moulded test bars were determined by a tensile experiment giving tensile strength, Young's modulus and elongation at break. Adding plasticizer facilitated the processing and up to 20 mass%, increased the tensile strength, Young's modulus and elongation at break as well. Higher amount of plasticizer diminished the tensile properties except elongation showing a slight increase. In all plasticized composites, organo-modified clay improved the tensile strength and at the same time, young's modulus and elongation almost remained constant. On the other hand, plasticized CA compounded with unmodified clay revealed lower properties. In a particular case, compounding of unplasticized CA with unmodified clay resulted in superior mechanical properties with a novel structure. So that, in optimum percentage –5 mass%- of unmodified clay, tensile strength and young's modulus increased significantly by 335% and 100%, to 178 MPa and 8.4 GPa, respectively. This is a dramatic improvement in strength and stiffness of CA. Adding organo-modified clay resulted in a little improvement in tensile properties. SEM pictures of the optimum composite showed a core/shell structure with high orientation in the shell part. It is supposed that this behaviour is caused by the interaction between CA hydroxyl groups and free cations existing in the galleries of unmodified clay.     

Nanocomposites by melt intercalation based on polycaprolactone and organoclay

Nanocomposites based on biodegradable polycaprolactone (PCL) and organically modified layered silicates (organoclay) were prepared by melt mixing. Their structures and properties were characterized by wide‐angle X‐ray diffraction, thermal analysis, and rheological measurements. The exfoliation of the organoclay was achieved via a melt mixing process in an internal mixer and showed a dependence on the type of organic modifier, the organoclay contents, and the processing temperature. The addition of the organoclay to PCL increased the crystallization temperature of PCL, but a high content of the organoclay could show an inverse effect. The PCL/organoclay nanocomposites showed a significant enhancement in their mechanical properties and thermal stability due to the exfoliation of the organoclay. The nanocomposites showed a much higher complex viscosity than the neat PCL and significant shear‐thinning behavior in the low frequency range. The shear storage modulus and loss modulus of the nanocomposites also exhibited less frequency dependence than the pure PCL in the low frequency range, and this was caused by the strong interactions between the organoclay layers and PCL molecules and by the good dispersion of exfoliated organoclay platelets in the PCL. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 670–678, 2003     

Structure and mechanical properties of poly(l-lactide)/layered silicate nanocomposites

Poly(ε-caprolactone) (PCL) masterbatches with the intercalated and the exfoliated morphology were prepared by ring opening polymerization of ε-caprolactone in the presence of organomodified montmorillonite (MMT) Cloisite 30B. Poly(l-lactide) (PLLA) nanocomposites with Cloisite 30B or PCL masterbatches were prepared by melt blending. The effects of the silicate type, MMT content and the nanocomposite morphology on thermal and mechanical properties of PLLA nanocomposites were examined. The montmorillonite particles in PLLA/Cloisite 30B and PLLA/intercalated masterbatch nanocomposites were intercalated. In contrary to expectations, the exfoliated silicate layers of exfoliated masterbatch were not transferred into the PLLA matrix. Due to a low miscibility of PCL and PLLA, MMT remained in the phase-separated masterbatch domains. The stress-strain characteristics of PLLA nanocomposites, Young modulus E, yield stress σ_y and yield strain ε_y, decreased with increasing MMT concentration, which is associated with the increase in PCL content. The expected stiffening effect of MMT was low due to a low aspect ratio of its particles and was obscured by both plastifying effects of PCL and low PLLA crystallinity. Interestingly, in contrast to the neat PLLA, ductility was enhanced in all PLLA/Cloisite 30B materials and in PLLA/masterbatch nanocomposites with low MMT concentrations.     

Biodegradable polyester nanocomposites: The effect of structure on mechanical and degradation behavior

The study describes the effect of the layered silicate content and its dispersion on the mechanical behavior of poly(ε-caprolactone) (PCL) nanocomposites and their corresponding changes during the degradation in a phosphate buffer at 37 °C. Two nanocomposite systems were compared: intercalated and exfoliated nanocomposites. They were prepared by melt-compounding of a high-molecular-weight PCL with in situ polymerized silicate masterbatches or an organophilized montmorillonite. It has been shown that Young modulus increases with the increasing silicate content and at the same time, the highest increase in the modulus is observed for the exfoliated system. The stiffness enhancement is predominantly caused by the dispersed inorganic phase but also supported by the contribution of the low-molecular-weight PCL fraction, which comes from the masterbatch, to the total degree of crystallinity. In contrast, the increase in the yield stress is driven mainly by the present low-molecular-weight PCL fraction with higher crystallinity. The degradation behavior reflects both the presence of the layered silicate as well as the low-molecular-weight PCL fraction. Their presence accelerates the degradation in the phosphate buffer at 37 °C.     

Chlorinated polyethylene nanocomposites using PCL/clay nanohybrid masterbatches

Exfoliated nanocomposites were prepared by dispersion of poly(ε-caprolactone) (PCL) grafted montmorillonite nanohybrids used as masterbatches in chlorinated polyethylene (CPE). The PCL-grafted clay nanohybrids with high inorganic content were synthesized by in situ intercalative polymerization of ε-caprolactone between silicate layers organo-modified by alkylammonium cations bearing two hydroxyl functions. The polymerization was initiated by tin alcoholate species derived from the exchange reaction of tin(II) bis(2-ethylhexanoate) with the hydroxyl groups borne by the ammonium cations that organomodified the clay. These highly filled PCL nanocomposites (25 wt% in inorganics) were dispersed as masterbatches in commercial chlorinated polyethylene by melt blending. CPE-based nanocomposites containing 3-5 wt% of inorganics have been prepared. The formation of exfoliated nanocomposites was assessed both by wide-angle X-ray diffraction and transmission electron microscopy. The thermal and thermo-mechanical properties were studied as a function of the filler content, by differential scanning calorimetry and dynamic mechanical analysis, respectively. The mechanical properties were also assessed by tensile tests. The Young’s modulus of CPE is increased by a decade when a PCL-grafted clay masterbatch is exfoliated to reach 5 wt% of clay in the resulting nanocomposite. The influence of PCL-grafting on the properties of these nanocomposites was investigated by comparison with materials obtained with ungrafted-PCL.     

Polymer-layered silicate nanocomposites based on poly(ε-caprolactone)

Poly(ε-caprolactone) nanocomposites based on montmorillonite modified with hexadecyltrimethylammonium bromide (M-HTAB) were prepared by the in situ polymerization technique. As a result, nano-structured PCL/M-HTAB systems were obtained. It was found that the molecular weight of PCL decreased with an increase in silicate content in the system. Within the investigated range of molecular weight, crystallization behavior of poly(ε-caprolactone) was affected only by the presence of M-HTAB. A silicate loading of higher than 10 wt.% reduced both crystallinity degree and the crystallization rate of PCL. The structure of obtained intercalated nanocomposites depended on the amount of montmorillonite in the systems. The periodicity of clay layers, estimated by X-ray diffraction, was found to be high at increased silicate loading in the nanocomposite. Since PCL and SAN are miscible, an attempt was made to use PCL/M-HTAB systems as a modifier for SAN matrix. Apparently, a quantity as small as 0.66 wt.% of M-HTAB in such blends induced a clear increase in material stiffness. An increase of Young's modulus of more than 40% in comparison to neat SAN was observed at 5.65 wt.% silicate loading.     

Thermal and mechanical properties of PE/organoclay nanocomposites

Polyethylene/montmorillonite clay nanocomposites were obtained via direct melt intercalation. The clay was organically modified with four different types of quaternary ammonium salts. The objective of this work is to study the use of montmorillonite clay in the production of nanocomposites by means on rheological, mechanical and crystallization properties of nanocomposites and to compare to the properties of the matrix and PE/unmodified clay nanocomposites. In general, the tensile test showed that the yield strength and modulus of the nanocomposites are close to the pure PE. Apparently, the mixture with Dodigen salt seems to be more stable than the pure PE and PE/unmodified clay.     

Exfoliated high-impact polystyrene/MMT nanocomposites prepared using anchored cationic radical initiator-MMT hybrid

High-impact polystyrene (HIPS)/montmorillonite (MMT) nanocomposites were prepared via in-situ polymerization of styrene in the presence of polybutadiene, using intercalated cationic radical initiator-MMT hybrid. Incomplete exfoliation of the silicate layers in the HIPS nanocomposites was observed when a bulk polymerization was employed. On the other hand, the silicate layers were efficiently exfoliated in the PS matrix during a solution polymerization, due to the low extra-gallery viscosity, which can facilitate the diffusion of styrene monomers into the clay layers. The resulting exfoliated HIPS/MMT nanocomposites were characterized by X-ray diffraction, transmission electron microscopy, thermogravimetric analysis, particle size analysis, gel permeation chromatography, and dynamic mechanical analysis. The nanocomposites exhibited significant improvement in thermal and mechanical properties. For example, about 50% improvement in Young’s modulus was achieved with 5 wt% of clay, compared to the unmodified polymer counterpart.     

Molecular motion,morphology, and thermal properties of multiwall carbon nanotube/polysilsesquioxane composite

Diglycidyl ether of bisphenol A (DGEBA)‐bridged polyorganosiloxane precursors have been prepared successfully by reacting diglycidyl ether of bisphenol A epoxy resin with 3‐aminopropyltriethoxysilane. Acid‐modified and unmodified multiwalled carbon nanotube (MWCNT) were dispersed in the diglycidyl ether of bisphenol A‐bridged polyorganosiloxane precursors and cured to prepare the carbon nanotube/diglycidyl ether of bisphenol A‐bridged polysilsesquioxane (MWCNT/DGEBA‐PSSQ) composites. The molecular motion of MWCNT/DGEBA‐PSSQ nanocomposites was studied by high‐resolution solid‐state ¹³C NMR. Acid‐modification can improve the affinity between MWCNT and the polymer matrix. The molecular motion of the DGEBA‐PSSQ decreased with acid‐modified MWCNT content. However, when unmodified MWCNT was used, the molecular motion of the DGEBA‐PSSQ was increased. SEM and TEM microphotographs confirm that acid‐modified MWCNT exhibits better dispersion than unmodified MWCNT in DGBEA‐PSSQ. The dynamic mechanical properties of acid‐modified MWCNT/DGBEA‐PSSQ composites are more favorable than those of unmodified MWCNT. T_g of the DGEBA‐PSSQ decreased from 174.0 °C (neat DGEBA‐PSSQ) to 159.0 °C (1 wt % unmodified MWCNT) and 156.0 °C (1 wt % acid‐modified MWCNT). The storage modulus (at 30 °C) of the DGEBA‐PSSQ increased from 1.23 × 10⁹ Pa (neat DGEBA‐PSSQ) to 1.65 × 10⁹ Pa (1 wt % acid‐modified MWCNT). However, when unmodified MWCNT was used, the storage modulus of the DGEBA‐PSSQ decreased to 6.88 × 10⁸ Pa (1 wt % unmodified MWCNT). At high temperature, above 150 °C, storage modulus of nanocomposites was higher than that of neat polymer system. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 472–482, 2008     

Polyester/organo‐graphite oxide composite: Effect of organically surface modified layered graphite on structure and physical properties of poly(ε‐caprolactone)

Silylated graphite oxide (sGO) was selected as suitable filler to improve the mechanical and electrical conductive properties of poly(ε‐caprolactone) (PCL). The composites of PCL and sGO were prepared by solution blending method. By modifying the surface of GO with silylation reagent (octyltrichlorosilane), the interlayer space of graphite oxide (GO) was increased and an excellent dispersion of the modified GO in the organic solvent and into the PCL matrix was achieved. The structures and physical properties of the sGO/PCL composites were characterized by the fourier transform infrared (FTIR), thermogravimetric analysis (TGA), wide angle X‐ray diffraction (WAXD) analysis, differential scanning calorimeter (DSC), tensile tests, dynamic mechanical analysis (DMA), and volume resistivity measurements. It indicated that the PCL/sGO composites formed an exfoliated structure from the WAXD study. The tensile strength and Young′s modulus of PCL increased with the addition of sGO. It was also found that a small amount of the sGO platelets in the composite could act as a nucleating agent and accelerated the crystallization of PCL. Further, the addition of the sGO platelets into the PCL matrix increased the volume electrical conductivity of PCL. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 294–301, 2010     

Preparation of polymer nanocomposites with enhanced mechanical properties using hybrid of graphene and partially wrapped multi-wall carbon nanotube as nanofiller

Triblock copolymer of poly(p-dioxanone) and polyethylene glycol end-capped with pyrene moieties ((Py-PPDO)₂-b-PEG) was synthesized and used as modifier for multi-wall carbon nanotubes (MWCNTs). Nano-aggregates ((Py-PPDO)₂-b-PEG@MWCNTs) with shish-kebab like partially wrapped morphology and very good stability were obtained by incorporating the copolymer with MWCNTs. The bare MWCNT sections of (Py-PPDO)₂-b-PEG@MWCNTs were able to induce π-π interactions with graphene (GE) and resulted in a novel GE/(Py-PPDO)₂-b-PEG@MWCNTs hybrid. The dispersity of GE in solution or polymer matrix was therefore greatly improved. The PCL nanocomposite films using GE/(Py-PPDO)₂-bPEG@MWCNTs as hybrid nanofiller exhibited obviously improved mechanical properties especially at very low hybrid nanofiller content. The influence of the nanofiller content and feed ratio of GE/MWCNTs on the mechanical properties of composites films was evaluated. When the feed ratio of GE to MWCNTs is 2:8 and the total loading of nanofiller is only 0.01 wt%, the tensile strength of the composite film increased by 163% and the elongation at break increased by 17% compared to those of neat PCL. These results can be attributed to fine dispersion of the nanofillers in PCL matrix and the hybrid interactions between GE and MWCNTs. Therefore, this work provides a novel method for preparing polymer nanocomposites with high mechanical performance and low nanofiller loading.     

Fabrication of Bioactive Polyoxymethylene Nanocomposites for Bone Tissue Replacement

Summary: Stearic acid modified nano hydroxyapatite (n-SHA) filled polyoxymethylene (POM) nanocomposites were prepared by melt mixing method for bone tissue replacement and regeneration applications. Contact angle measurements of POM nanocomposites were carried out to understand the effect of n-SHA addition on the hydrophobicity of nanocomposites. The mechanical properties like tensile strength, Young's modulus and elongation at break were found to be increased significantly by the incorporation of n-SHA into the POM matrix. The bone-bonding ability of the nanocomposites was evaluated by examining the apatite formation on their surface after soaking in simulated body fluid (SBF) and apatite formation was studied by atomic force microscopy (AFM). The protein adhesion studies revealed the enhanced biocompatibility of the nanocomposites due to the presence of n-SHA nanofillers on the surface and it provides favorable binding sites for protein adsorption. The significant improvement in the biocompatibility as well as mechanical, thermal and hydrophobic properties of the POM nanocomposites makes it a potential future material for bone implantation.     

The effect of surface-modified nano-hydroxyapatite on biocompatibility of poly(ε-caprolactone)/hydroxyapatite nanocomposites

We describe the effect of surface-modified hydroxyapatite (HAp) nano-crystals on biocompatibility of a new-type nanocomposite consisting of poly(ε-caprolactone) (PCL) and HAp. Surface-modified hydroxyapatite (HAp) nano-crystals were prepared by chemically grafting PCL on HAp surfaces. Time-dependent phase monitoring indicated that PCL surface-grafting contributed to the enhanced dispersion of HAp at nano-level in the PCL solution. The protein adhesion and cell experiments showed that the presence of PCL-grafted HAp nano-crystals in nanocomposites contributed to the enhanced biocompatibility. PCL-grafted HAp in nanocomposites provided more favorable environments for protein adsorption, compared with unmodified HAp. Nanocomposites containing PCL-grafted nanophase HAp showed positive effects on adhesion and proliferation of NIH3T3 fibroblasts.     

Physical properties of poly(ε‐caprolactone) layered silicate nanocomposites prepared by controlled grafting polymerization

Poly(ε‐caprolactone) (PCL) chains grafted onto montmorillonite modified by a mixture of nonfunctional ammonium salts and ammonium‐bearing hydroxyl groups were prepared. The clay content was fixed to 3 wt %, whereas the hydroxyl functionality was 25, 50, 75, and 100%, obtaining an intercalated or exfoliated system. The transport properties of water and dichloromethane vapors and the mechanical properties were investigated. The mechanical and dynamic mechanical analyses showed improvement of the nanocomposite elastic modulus in a wide temperature range. Interestingly, for the higher hydroxyl contents (50, 75, and 100%), the decrease of modulus at higher temperature, due to the PCL crystalline melting, did not lead to the loss of mechanical consistence of the samples. Consequently, they revealed a measurable modulus up to 120 °C, a much higher temperature with respect to pure PCL. Water sorption was investigated in the entire activity range, and a lower sorption was observed on increasing the hydroxyl content, up to the sample with 100% hydroxyl content, which turned to be completely impermeable, even in liquid water. The sample with 75% hydroxyl content showed a threshold activity (a = 0.4) below which it was impermeable to water vapor. Also, the diffusion parameters decreased when the hydroxyl content increased, up to the 100% sample, which showed zero diffusion. The diffusion parameters of an organic vapor, dichloromethane, also exhibited a decreasing value on increasing the hydroxyl content in the nanocomposites. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1466–1475, 2004     

Transesterification catalysts to improve clay exfoliation in synthetic biodegradable polyester nanocomposites

We report here on the melt intercalation preparation of polymer/clay nanocomposites based on three commercial synthetic biodegradable polyesters: EastarBio Ultra, Ecoflex, and Bionolle, respectively. The montmorillonite clay addition is performed either by direct dispersion of Cloisite 30B in the polyester matrix or by dispersing a “PCL-grafted Cloisite 30B” masterbatch in the biodegradable polyesters. All obtained nanocomposites display an intercalated morphology as attested by X-ray diffraction measurements. The various analyses clearly show that the Bionolle (BIO) matrix gives the best results. Morphological characterization and mechanical properties of these nanocomposites also show that the “masterbatch route” leads to poor results as a consequence of the very low compatibility between the poly(ε-caprolactone) (PCL) of the masterbatch and the three other polyester matrices. In a second part, nanocomposites based on the BIO matrix are prepared by direct dispersion of the organo-clay in the presence of three different metal-based catalysts with the aim to promote transesterification reactions between the nanocomposite constituents. The mechanical properties and morphological characterization of these nanocomposites show that the tin-based catalyst (Sn) is the more efficient. Indeed, the effectiveness of transesterification reactions taking place between the ester functions of the BIO matrix and the hydroxyl groups of the organo-clay and the resulting “grafting” of BIO chains on the organo-clay surface are confirmed by thermogravimetric analyses performed after the extraction procedure. TEM observations show that this catalyst enhances the clay platelets exfoliation within the BIO matrix as a consequence of the transesterification reactions. Nanocomposites prepared in presence of Sn show better clay dispersion and enhanced stiffness with a 60% increase in Young’s modulus.     

Preparation of the polymer–clay nanocomposites in exfoliated state by interface stabilization

To suppress the repulsive interfacial energy between hydrophilic clay and a hydrophobic polymer matrix for polymer–clay nanocomposites, a third component of amphiphilic nature such as poly(?‐caprolactone) (PCL) was introduced into the styrene–acrylonitrile copolymers (SAN)/Na‐montmorillonite system. Once ?‐caprolactone was polymerized in the presence of Na‐montmorillonite, the successful ring‐opening polymerization of ?‐caprolactone and the well‐developed exfoliated structure of PCL/Na‐montmorillonite mixture were confirmed. Thereafter, SAN was melt‐mixed with PCL/Na‐montmorillonite nanocomposite, and the SAN matrix and PCL fraction were completely miscible to form a homogeneous mixture with retention of the exfoliated state of Na‐montmorillonite, exhibiting that PCL effectively stabilizes the repulsive polymer–clay interface and contributes to the improvement of the mechanical properties of nanocomposites. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 246–252, 2004     

聚吡咯改性层状黏土/聚己内酯抗菌纳米复合材料的制备与性能

利用Fe³⁺引发吡咯（Py）在层状双羟基金属氧化物（LDHs）表面发生氧化反应,形成聚吡咯（PPy）包覆LDHs（LDHs@PPy）;以LDHs@PPy和聚己内酯（PCL）为原料,采用溶液浇筑方法制备LDHs@PPy/PCL纳米复合薄膜.研究结果表明,LDHs@PPy对大肠杆菌和金黄色葡萄球菌的抗菌率均达到99.7%,其与基材PCL界面相容性良好,而且在基材中还具有异相成核作用.当LDHs@PPy的质量分数仅为1%时,LDHs@PPy/PCL纳米复合材料的拉伸强度和断裂伸长率分别增加35%和23%,氧气渗透性降低幅度达到56%,对大肠杆菌和金黄色葡萄球菌的抗菌率均超过99.99%,表现出良好的抗菌活性,拓展了层状黏土/生物基高分子复合材料在活性包装领域的应用.