层状类钙钛矿结构有机-无机杂合物的制备

综述了近年来层状类钙钛矿结构有机-无机杂合物的制备方法,包括有机元、无机元的选择及其合成.     

层状结构杂合物(C_nH_(2n+1)NH_3)_2NiCl_4(n=4,8,12)的合成与表征（英文）

采用低温固相合成法制备了3种有机/无机杂合物(CnH2n+1NH3)2NiCl4(n=4,8,12),通过元素分析、X射线粉末衍射、红外光谱和紫外-可见吸收光谱对杂合物进行了表征.实验结果表明,利用低温固相合成法可成功制备杂合物(CnH2n+1NH3)2NiCl4(n=4,8,12),3种产物均具有明显的层状结构且分别属于单斜晶系、六方晶系和正交晶系.     

层状结构杂合物（CnH2n＋1 NH3）2 NiCl4（n ＝4，8，12）的合成与表征

采用低温固相合成法制备了3种有机／无机杂合物（ Cn H2n ＋1 NH3）2 NiCl4（ n ＝4,8,12）,通过元素分析、X 射线粉末衍射、红外光谱和紫外‐可见吸收光谱对杂合物进行了表征。实验结果表明,利用低温固相合成法可成功制备杂合物（Cn H2n ＋1 NH3）2 NiCl4（ n ＝4,8,12）,3种产物均具有明显的层状结构且分别属于单斜晶系、六方晶系和正交晶系。     

第二结构导向剂诱导形成的二维有机模板稀土硫酸盐（英文）

水热条件下合成了具有超大孔道和层状结构的有机模板稀土硫酸盐。超大孔道的稀土硫酸盐(1)的分子式为[(CH3)2NH2]9[Pr5(SO4)12]·2H2O,它展现出有趣的交叉二十元环孔道结构。层状的稀土硫酸盐的分子式为[H3O]3[(CH3)2NH2]3[Ln2(SO4)6](Ln=Pr,2;Nd,3),它可以被看作是由双链和八元环结合而成。这3种化合物的合成揭示了大的有机胺(三聚氰胺)可能用作为第二结构导向剂,阻止形成高维数的无机骨架,从而诱导了二维层状结构稀土硫酸盐晶体的生长。对化合物1和3的磁性进行了研究,测试的温度范围在2~300 K。     

含Fe(Ⅲ)离子有机-无机层状类钙钛矿杂合物修饰电极对对苯二酚的电催化作用及测定

以酚藏花红为有机层、含三价铁的K3Fe(CN)6为无机层在空气中合成了有机-无机层状类钙钛矿杂合物修饰碳糊电极。利用扫描电镜(SEM)和X-射线衍射(XRD)对其表面形貌和微观结构进行表征,并用循环伏安法研究了杂合物修饰电极的电化学性质,发现该电极对对苯二酚具有良好的电催化作用。结果表明,在pH5.0的PBS缓冲溶液中,对苯二酚在空白碳糊电极上为二步还原过程而在修饰电极上只有一步还原过程,修饰电极更有利于检测对苯二酚。采用微分脉冲伏安法在-0.4～0V电位范围内进行扫描,在-240.2mV处的还原峰电流与对苯二酚浓度在1.0×10-6～1.0×10-3mol/L范围呈良好的线性关系,相关系数为0.9951,检出限为4.73×10-7mol/L。对1.0×10-5mol/L的对苯二酚连续测定5次,相对标准偏差为1.8%。模拟样品中对苯二酚的平均加标回收率为102%。     

以1,6-己二胺为模板剂的层状磷酸锆晶体的合成与表征

 采用水热法合成了以1,6-己二胺(HDA)为模板剂的层状磷酸锆晶体0.5·1.5H2O,并用单晶及粉末XRD,IR和TG-DTA等对其结构和性质进行了表征. 该晶体是由磷酸锆无机层、有机胺以及水分子三部分构成的层状结构,层间距约为1.77 nm,无机层结构为γ-型. 位于有机胺两端的氮与无机层表面部分羟基的氧以氢键连接,水分子占据磷酸锆层间的两种位置. 单晶结构模拟得到的XRD谱与从粉末样品采集的XRD谱基本吻合. 此晶体在180 ℃下脱去水分子,在220 ℃下加热3 h其结构未发生明显变化; 有机胺模板剂在250 ℃下开始分解.     

层状有机/无机杂化物(C_4H_9NH_3)_2NiCl_4的合成与表征(英文)

以NiCl2·6H2O和C4H9NH2·HCl为原料,利用固相合成法成功合成了层状结构的有机/无机杂化物(C4H9NH3)2NiCl4(1);采用X射线粉末衍射仪和红外光谱仪表征了产物1的结构,利用元素分析和热重分析测定了其元素组成和热稳定性.结果表明,杂化物1具有层状结构,层间距为3.220 7nm.     

[Co(1,10-phen)(H_2O)(VO_3)_2]的水热合成、结构及电化学性质

采用水热方法并以邻菲啉为模板剂合成了一种过渡金属配合物连接的无机-有机层状结构的多金属钒酸盐Co(1,10-phen)(H2O)(VO3)2,该化合物经过X-射线单晶衍射、元素分析、红外光谱表征和热失重分析,并用循环伏安法研究了标题化合物的电化学性质.     

层状溶致液晶中磁性纳米粒子掺杂的研究

选择非离子表面活性剂十二烷基(4)聚氧乙烯醚(C₁₂E₄)与H₂O构成的溶致液晶(LLC)层状模板, 掺杂油酸铵包覆的Fe₃O₄亲水性磁性纳米粒子, 构建稳定的有机/无机杂合体. 用透射电镜(TEM), X射线粉末衍射(XRD), 偏光显微镜(POM), 小角X射线散射(SAXS)和振动探针式磁强计(VSM)等对粒子及掺杂前后的层状液晶相结构变化进行表征. 结果表明, 粒子掺入使LLC模板的层间距产生了改变, 同时增强了体系有序性．通过对杂合体表征结果的分析, 阐述了模板与粒子间相互作用的机理.     

新型层状磷酸铝[Al6P8O32][(C2H5)2NHCH2CH2NH3]2·[C2H5NH2CH2CH2NH2C2H5] 的合成、表征及其共模板作用

在溶剂热体系中,以N,N-二乙基乙二胺为结构导向剂,合成了Al/P为3/4的层状磷酸铝[Al6P8O32][(C2H5)2NHCH2CH2NH3]2·[C2H5NH2CH2CH2NH2C2H5]单晶,并通过X射线单晶衍射结构分析.XRD,ICP,元素分析,差热-热重分析等手段进行了表征.该化合物属单斜晶系,P2(1)/c空间群,晶胞参数:a=0.90945(2)nm,b=1.46424(4)nm,c=1.87572(5)nm,β=102.672(2)°,Z=4.其阴离子层由AlO4四面体和PO3(=O)四面体单元交替连接构成,形成四、六、八元环拓扑结构,无机层以ABAB方式堆积,两种质子化的有机胺分子N,N-二乙基乙二胺及其重排产物N,N′-二乙基乙二胺填充在层间.用分子动力学模拟方法,考察了标题化合物中有机胺与无机层间的相互作用,讨论了这两种有机胺的共模板作用.     

Preparation and formation mechanism of a n-butylammonium/MnO2 layered hybrid via a one-pot synthesis under moderate conditions

The preparation of organic/inorganic layered hybrids has relied on multistep processing. Thus, shortening the synthetic procedure is important for possible future applications, but only a few studies report one-pot syntheses. In this work, we established a simple one-pot solution process to synthesize layered alkyl ammonium/MnO(2) hybrids, by stirring MnCl(2) and alkyl amine/H(2)O(2) aqueous solutions at 40 °C; the reaction concept is a chemical oxidation of Mn(II) ions in the presence of alkyl amine in aqueous solution. Furthermore, the formation mechanism of the layered n-butylammonium/MnO(2) hybrid was examined by following the structural and optical changes during the reaction, revealing that the one-pot reaction includes 3 steps; formation of β-MnOOH, topotactic oxidation of β-Mn(III)OOH to form the protonated layered manganese oxide H(x)Mn(III, IV)O(2)·yH(2)O, and ion-exchange of interlayer H(+) (or H(3)O(+)) with n-butylammonium to form layered n-butylammonium/MnO(2).     

Preparation and characters of hyperbranched polyester‐based organic‐inorganic hybrid material compared with linear polyester

To compare the properties of hyperbranched polymers with linear oligomers for preparing organic‐inorganic hybrids, hyperbranched aliphatic polyester (Boltorn^TM H20) and linear polyester hexa‐acrylate (EB830) were selected as organic components for preparing UV‐curable transparent hybrid materials using 3‐(trimethoxysilyl) propylmethacrylate as a coupling agent via a sol‐gel process. The prehydrolyzed product of tetraethoxysilane was used as an inorganic component. The effects of inorganic content on the morphologies, thermal behaviors, photopolymerizaiton kinetics and mechanical properties of the hybrids were investigated. The results show that for hyperbranched polyester‐based hybrids, the organic phase shows much better compatibility with inorganic phase even at high inorganic component content due to its special spheral shape and plenty of functional end groups, compared with linear EB830‐based hybrids. Copyright © 2004 John Wiley & Sons, Ltd.     

Phase structure and thermomechanical properties of primary and tertiary amine‐cured epoxy/silica hybrids

Several kinds of organic–inorganic hybrids were synthesized from an epoxy resin and a silane alkoxide with a primary amine‐type curing agent or tertiary amine curing catalyst. In the hybrid systems cured with the primary amine‐type curing agent, the storage modulus in the high‐temperature region increased, and the peak area of the tan δ curve decreased. Moreover, the mechanical properties were improved by the hybridization of small amounts of the silica network. However, these phenomena were not observed in the hybrid systems cured with the tertiary amine catalyst. The differences in the network structures of the hybrid materials with the different curing processes were characterized with Fourier transform infrared (FTIR). In the hybrid systems cured with the primary amine‐type curing agent, FTIR results showed the formation of a covalent bond between silanol and hydroxyl groups that were generated by the reaction of an epoxy group with an active hydrogen of the primary amine. However, this phenomenon was not observed in the hybrids cured with the tertiary amine. The hybrids with the primary amine showed a homogeneous microstructure in transmission electron microscopy observations, although the hybrids cured with the tertiary amine showed a heterogeneous structure. These results mean that the differences in the interactions between the organic and inorganic phases significantly affect the properties and microstructures of the resultant composites. © 2001 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 1071–1084, 2001     

Processing and Properties of Inorganic-Organic Hybrids Containing Various Inorganic Components

Inorganic-organic hybrids containing various inorganic components have been synthesized from silanol-terminated polydimethylsiloxane (PDMS) and three different inorganic components: Al(O-sec-C4H9)3, Ti(OC2H5)4 and Ta(OC2H5)5. The hybrids obtained were transparent and flexible. Dynamic mechanical measurements and stress-strain experiments were carried out in order to study the effect of inorganic component on the properties of the Metal-O-PDMS hybrids. The storage modulus at around room temperature increased in the order Al-O-PDMS, Ti-O-PDMS, Ta-O-PDMS hybrids, indicating that the three-dimensional network structure became denser in this order. The tensile strength increased in the order Al-O-PDMS, Ta-O-PDMS, Ti-O-PDMS hybrids. The difference in tensile strength is considered to be related to the strength of the interaction between the inorganic component and PDMS. The elongation at failure also depended on the inorganic component. Ti-O-PDMS hybrid exhibited the largest elongation of all the samples (more than 200%).     

Silica hybrid nanocomposites

In this work we present experimental results about the formation, properties and structure of sol — gel silica based biocomposite containing Calcium alginate as an organic compound. Two different types of silicon precursors have been used in the synthesis: tetramethylortosilicate (TMOS) and ethyltrimethoxysilane (ETMS). The samples have been prepared at room temperature. The hybrids have been synthesized by replacing different quantitis of the inorganic precursor with alginate. The structure of the obtained hybrid materials has been studied by XRD, IR Spectroscopy, EDS, BET and AFM. The results proved that all samples are amorphous possessing a surface area from 70 to 290 m²/g. It has also been established by FT IR spectra that the hybrids containing TMOS display Van der Walls and Hydrogen bonding or electrostatic interactions between the organic and inorganic components. Strong chemical bonds between the inorganic and organic components in the samples with ETMS are present. A self-organized nanostructure has been observed by AFM. In the obtained hybrids the nanobuilding blocks average in size at about 8–14 nm for the particles.     

Effect of Inorganic Components on Thermal Stability of Methylsiloxane-Based Inorganic/Orgnaic Hybrids

The thermal decomposition behavior of methylsiloxane-based inorganic/organic hybrids containing an inorganic component derived from metal alkoxides such as Si(OCH₃)₄, Al(O^sC₄H₉)₃, Ti(OⁱC₃H₇)₄ and Nb(OC₂H₅)₅ was investigated by means of thermogravimetric and differential thermal analysis (TG-DTA), Fourier transform infrared (FT-IR) spectroscopy and nuclear magnetic resonance (NMR) spectroscopy. The decomposition temperature of methyl groups in methylsiloxane-based inorganic/organic hybrids containing an inorganic component derived from metal alkoxides was higher than that in the methylsiloxane-based inorganic/organic hybrid prepared from only CH₃Si(OC₂H₅)₃. In particular, when incorporating Nb and Ti inorganic components, methyl groups in methylsiloxane-based inorganic/organic hybrids decomposed at about 100 and 200^∘C higher temperatures, respectively, than those in the methylsiloxane-based inorganic/organic hybrid prepared from only CH₃Si(OC₂H₅)₃. The incorporation of an inorganic component other than siloxane into methylsiloxane-based inorganic/organic hybrids was found to thermally stabilize the methyl groups of methylsiloxane networks.     

In Situ Fabrication of ZnS Semiconductor Nanoparticles in Layered Organic-inorganic Solid Template

Ordered ZnS semiconductor nanoparticles were in situ synthesized in metal halide perovskite organic/inorganic layered hybrids (CnH2n 1NH3)2ZnCl4 (n=10 and 12) by reaction of their spin-casting films with H2S gas. Transmission electron microscopy, UV-vis spectroscopy and small-angle X-ray diffraction were used to characterize the morphology and the structure of formed nanoparticles. Obtained results indicate an effective way to incorporate functional inorganic nanoparticles into structured organic matrices.     

Flexible inorganic–organic hybrids with dual inorganic components

Combining multiple inorganic components is an effective approach to improve the mechanical properties of inorganic–organic hybrid materials. The inorganic components can form interactions with the organic polymer matrix, and there is thus a need to understand the reinforcement mechanism under the optimal combination of organic polymer and inorganic particles. In this work, we prepared a series of dual inorganic particle–based titania/silica–poly(tetrahydrofuran)–poly(ε-caprolactone) (TiO₂/SiO₂–PTHF–PCL) hybrids by means of simultaneous cationic ring-opening polymerization and sol–gel reaction. In addition to constructing hybrid networks, the SiO₂ and TiO₂ components play important roles in multiple toughening mechanisms. The prepared dual inorganic hybrids feature enhanced thermal stability and mechanical properties when compared with the ones with a single inorganic component. The optimized mixing of such two inorganic components is identified through mechanical tests, revealing that the hybrid polymer₇₀/(Si_0.6Ti_0.4)₃₀ (70/18/12 mass ratio) has the highest compressive failure strain (80%) and compressive ultimate strength (1.3 MPa) as well as storage modulus (120 kPa), enabling elongation of up to 37% when compared with its original length. We thus find that the dual inorganic component approach is an effective strategy to enhance the mechanical properties of hybrid materials, suggesting potential applications as scaffolds for tissue engineering and soft robotics.     

Multifunctional hybrid organic-inorganic catalytic materials with a hierarchical system of well-defined micro- and mesopores

Novel layered zeolitic organic-inorganic materials (MWW-BTEB) have been synthesized by intercalation and stabilization of arylic silsesquioxane molecules between inorganic zeolitic MWW layers. The organic linkers are conformed by two condensed silyl-arylic groups from disilane molecules, such as 1,4-bis(triethoxysilyl)benzene (BTEB), which react with the external silanol groups of the zeolitic layers. The hybrids contain micropores within the inorganic layers and a well-defined mesoporous system in between the organic linkers. An amination post-treatment introduces basic groups in the organic linkers close to the acid sites present in the structural inorganic counterpart. Through this methodology it has been possible to prepare bifunctional acid-base catalysts where the acid sites are of zeolitic nature located in the inorganic building blocks and the basic sites are part of the organic structure. The resultant materials can act as bifunctional catalysts for performing a two-step cascade reaction that involves the catalytic conversion of benzaldehyde dimethylacetal into benzylidene malononitrile.