Removal of Pb and Cd from aqueous media and fish liver using novel polyurethane foam functionalized with pyrazolone as a new metal ion collector

In the present paper, an off-line preconcentration procedure for the determination of cadmium and lead by flame atomic absorption spectrometry (FAAS) is proposed. Polyurethane foam (PUF) functionalized with o-aminophenol (o-AP) followed by Pyrazolone (Pyr) packed in a minicolumn was used as a sorbent material. The metals were retained on the modified PUF, from which it could be eluted and effectively preconcentrated. The detection limits were 0.072 and 0.016 μg L⁻¹ for Pb and Cd respectively. Enrichment factors were 250 and 319 for lead and cadmium respectively. The procedure has been applied successfully to metal determination in water samples, fish liver and reference material.      

Indirect determination of lutetium by differential pulse anodic stripping voltammetry at a hanging mercury drop electrode

Lutetium has been determined by differential pulse anodic stripping voltammetry in an acidic solution containing Zn-EDTA. Lutetium (III) ions liberated zinc (II), which was preconcentrated on a hanging mercury drop electrode and stripped anodically, resulting in peak current linearly dependent on lutetium (III) concentration. Less than 0.4 ng mL⁻¹ lutetium could be detected after a 2 min deposition.      

Solid phase selective separation and green preconcentration of Cu, Zn, Pb and Cd in drinking water by using novel functionalized resin

A new solid — phase extraction sorbent was developed based on stepwise anchoring of two ligand molecules for the determination of copper, zinc, lead and cadmium in drinking water by flame AAS. Amberlite XAD-2 functionalized with 4′-(2-hydroxyphenylazo)-3′-methyl-1′-phenyl-2′-pyrazolin-5′-one (HPAPyr) was utilized for preconcentration/separation of these elements. The sorbent was prepared by two successive azo coupling reactions. First, 2-aminophenol was anchored to the amino groups in the resin resulted from nitration followed by reduction. Then, the resulted 2-aminophenol functionalized resin was further diazotized and coupled to the pyrazolone compound and the final product HPAPyr-XAD-2 was characterized by IR and elemental analysis. The optimum pH range for sorption, shaking time, exchange capacity, sample flow rate, preconcentration factor and interference from co-existing ions were investigated. All metal ions were quantitatively desorbed from the resin by 4.5 mol L⁻¹ nitric acid solution. The sorbent provides limit of detection within the range 0.9–3.3 μg L⁻¹ and concentration factor up to 250. The procedure was validated by analysis of certified material NIST-SRM 1577b. Application to drinking water showed satisfactory results with relative standard deviation RSD ≤ 8.5%.      

Preliminary results of a quick,simple method of detecting antimony in water samples

Preliminary results of development of a direct and fast method of determination of antimony in samples of tap water using GFAAS are presented. The found levels of antimony were lower than permitted for human consumption. A mixture of Pd and Mg(NO₃)₂ (concentrations in the injected solution: 8.6 μg mL⁻¹ and 5.8 μg mL⁻¹ respectively) was used as the chemical modifier. The pyrolysis and atomization temperatures were 1000 and 1700°C, respectively and the mean analytical recovery 98.2%.      

Hollow fibre liquid phase microextraction of parabens

A hollow fibre liquid phase microextraction for gas chromatographic determination of some p-hydroxybenzoic acid esters has been developed. Chlorobenzene containing tetradecane as internal standard was used for the extraction. Optimized extraction was carried out at room temperature for 40 min in the presence of 0.4 g mL⁻¹ NaCl in the sample solution. Calibration was linear up to 30 mg L⁻¹. Correlation coefficients were 0.996–0.998. Enrichment factors were 21, 95 and 154, and detection limits were 0.20, 0.03 and 0.01 μg mL⁻¹ for methylparaben, ethylparaben and propylparaben, respectively. Reproducibility was acceptable with relative standard deviations up to 11.7%. The technique was tested for water and urine analysis.      

Development of efficient method for preconcentration and determination of copper, nickel, zinc and iron ions in environmental samples by combination of cloud point extraction and flame atomic absorption spectrometry

A cloud point extraction procedure for the preconcentration of copper, nickel, iron and zinc ions in various samples has been described. Analyte ions in aqueous phase are complexed with 3-((indolin-3-yl)(phenyl)methyl)indoline (IYPMI) and following centrifugation quantitatively extracted to the aqueous phase rich in Triton X-114. The surfactant-rich phase was dissolved in 2.0 mol L⁻¹ HNO₃ in methanol prior to metal content determination by flame atomic absorption spectrometry (FAAS). The effects of some parameters including, the concentrations of IYPMI, Triton X-114 and HNO₃, bath temperature, centrifuge rate and time were investigated on the recoveries of analyte ions. At optimum conditions, the detection limits of (3 SDb m⁻¹) of 1.6, 2.8, 2.1 and 1.1 ng mL⁻¹ for Cu²⁺, Fe³⁺, Ni²⁺ and Zn²⁺ along with preconcentration factors of 30 and enrichment factor of 48, 39, 34 and 52 for Cu²⁺, Ni²⁺, Fe³⁺ and Zn²⁺ respectively, were obtained. The proposed cloud point extraction has been successfully applied for the determination of metal ions in real samples with complicated matrix such as biological, soil and blood samples with high efficiency.      

Cloud point extraction-preconcentration and flame atomic absorption spectrometric determination of low levels of zinc in water and blood serum samples

A simple, sensitive and selective flotation method is described for the preconcentration and atomic absorption spectrometric determination of zinc ion in water and blood samples. At a solution pH of 5.2, 4-(2-pyridylazo-resorcinol) and Triton X-114 were used as hydrophobic ligand and non-ionic surfactant, respectively. The chemical variables affecting the preconcentration process were optimized. Under the optimized experimental conditions, the selective preconcentration and determination of as low zinc concentration as 6.5 μg L⁻¹ can be made. The proposed method was successfully applied to the preconcentration and low-level determination of zinc in different water and blood serum samples.      

Comparative studies on conventional and microwave-assisted synthesis of a series of 2,4-di and 2,3,4-trisubstituted benzimidazo[1,2-a] pyrimidines and their antimicrobial activities

Comparative studies were performed on a series of 2,4-di and 2,3,4-trisubstituted benzimidazo[1,2-a]pyrimidines, which were synthesized with conventional and microwave heating methods. In microwave irradiation method, approximately, 95–97.5% of the reaction time was increased and 1–45% yield increase was obtained. All compounds were able to inhibit the growth of the screened microorganisms in vitro with MIC values between 3.9–250 μg mL⁻¹. The highest activity was expressed by compound IIId (2,4-diphenyl-benzo[4,5]imidazo[1,2-a] pyrimidine), which has the MIC value of 3.9 μg mL⁻¹ and 31.2 μg mL^-1 for Penicillium natatum ATCC 24791 and E. faecalis ATCC 29212, respectively.      

Nickel and palladium complexes of enolatefunctionalised N-heterocyclic carbenes

The reaction of chloroethyltrimethylsilylether with 1-methylimidazole furnishes an ionic liquid that undergoes methanolysis to crystalline 2-hydroxyethylimidazolium chloride (crystal structure presented). Conversion to defined hydroxyethylimidazol-2-ylidene nickel complexes failed, but was accomplished with 1-methyl-3-acetophenyl-imidazolium bromide. The bis(NHC^⋂O⁻) nickel(II) chelate is formed, rather than a methallylnickel monochelate, but with nickelocene a monochelate NiCp complex was detected. The bulky 1-(2,6-diisopropylphenyl)-3-(2’-phenyl-enolato)-imidazol-2-ylidene allylpalladium chloride was obtained in pure form. Attempts to generate catalysts for ethylene oligomerization by in situ techniques have failed so far whereas P^⋂O⁻ ligands, comparable by the P-C diagonal relationship, provide active catalysts.      

Dispersive liquid-liquid microextraction and liquid chromatographic determination of pentachlorophenol in water

A simple and sensitive dispersive liquid-liquid microextraction method for extraction and preconcentration of pentachlorophenol (PCP) in water samples is presented. After adjusting the sample pH to 3, extraction was performed in the presence of 1% W/V sodium chloride by injecting 1 mL acetone as disperser solvent containing 15 μL tetrachloroethylene as extraction solvent. The proposed DLLME method was followed by HPLC-DAD for determination of PCP. It has good linearity (0.994) with wide linear dynamic range (0.1–1000 μg L⁻¹) and low detection limit (0.03 μg L⁻¹), which makes it suitable for determination of PCP in water samples.      

Surfactant to dye binding degree method for the determination of fluvoxamine maleate and citalopram hydrobromide in pharmaceuticals

The surfactant to dye binding degree (SBDB) methodology was used to determine fluvoxamine maleate and citalopram hydrobromide. Neutral red and sodium dodecyl sulfate (SDS) were used as the dye and surfactant, respectively, to form dye-surfactant aggregates. When a cationic drug is added to dye-surfactant mixture, it interacts with the surfactant and decreases the dye-surfactant binding degree. This decrease is proportional to the drug concentration. This was measured by monitoring the absorbance changes of the dye at 532 nm. Under the optimum conditions, the calibration graphs were linear over the range of 1.2–15 μg mL⁻¹ and 1.1–15 μg mL⁻¹ for fluvoxamine maleate and citalopram hydrobromide, respectively. The detection limits (signal to noise ratio = 3) were found to be 0.37 and 0.35 μg mL⁻¹, for fluvoxamine maleate and citalopram hydrobromide, respectively.      

Simultaneous kinetic spectrophotometric determination of Cu(II), Co(II) and Ni(II) using partial least squares (PLS) regression

A partial least squares (PLS-1) calibration model based on kinetic—spectrophotometric measurement, for the simultaneous determination of Cu(II), Ni(II) and Co(II) ions is described. The method was based on the difference in the rate of the reaction between Co(II), Ni(II) and Cu(II) ions with 1-(2-pyridylazo)2-naphthol in a pH 5.8 buffer solution and in micellar media at 25°C. The absorption kinetic profiles of the solutions were monitored by measuring the absorbance at 570 nm at 2 s intervals during the time range of 0–10 min after initiation of the reaction. The experimental calibration matrix for the partial least squares (PLS-1) model was designed with 30 samples. The cross-validation method was used for selecting the number of factors. The results showed that simultaneous determination could be performed in the range 0.1-2 μg mL⁻¹ for each cation. The proposed method was successfully applied to the simultaneous determination of Cu(II), Ni(II) and Co(II) ions in water and in synthetic alloy samples.      

Cobalt(II) ion-selective electrode with solid contact

A new all plastic sensor for Co²⁺ ions based on 2-amino-5 (hydroxynaphtyloazo-1′)-1,3,4 thiadiazole (ATIDAN) as ionophore was prepared. The electrode exhibits a low detection limit of 1.5 × 10⁻⁶ mol L⁻¹ and almost theoretical Nernstian slope in the activity range 4.0 × 10⁻⁶–1 × 10⁻¹ mol L⁻¹ of cobalt ions. The response time of the sensor is less than 10 s and it can be used over a period of 6 months without any measurable divergence in potential. The proposed sensor shows a fairly good selectivity for Co(II) over other metal ions. The electrode was successfully applied for determination of Co²⁺ in real samples and as an indicator electrode in potentiometric titration of Co²⁺ ions with EDTA.      

Ionic liquid promoted Diels-Alder Reaction between anthrone and maleimides

Ionic liquids (IL) are gaining importance as green solvents. Imidazolium ionic liquid [bmim]⁺[Cl]⁻, an environmentally benign solvent, was found to promote the Diels-Alder reaction between anthrone and maleimides at room temperature with excellent yields. The ionic liquid played a dual role as solvent and catalyst.      

Use of an immiscible diluent in ionic liquid / ion pair LC for the assay of an injectable analgesic

Injectable solutions used in treatment of intense pain are based on combinations of active ingredients such as metamizole sodium (MTZ), pitofenone hydrochloride (PTF) and fenpiverine bromide (FPB). The simultaneous chromatographic assay of such combinations poses difficulties due to their structural variety, highly polar character, and wide concentration ranges (500 mg mL⁻¹ for MTZ, 2 mg mL⁻¹ for PTF and 0.02 mg mL⁻¹ for FPB). Fast hydrolysis of MTZ on aqueous dilution causes additional problems due to impurity (MTC) formation. Sodium hexane sulphonate (10 mM) was used as ion pairing agent for PTF, FPB and MTC in a mobile phase consisting of 48/52 (v/v) methanol and aqueous 0.2% triethylamine at pH=3. The ionic liquid 1-butyl-1-methyl-pyrrolidinium tetrafluoroborate (10 mM) was used as mobile phase additive to preserve the MTZ peak symmetry. The minor active ingredient FPB was selectively extracted into 1-octanol by ion pair formation with picric acid. A 20 μL aliquot of the organic layer was directly injected into the column.      

Qualitative and quantitative analysis of gallic acid in Alchemilla vulgaris, Allium ursinum, Acorus calamus and Solidago virga-aurea by chip-electrospray ionization mass spectrometry and high performance liquid chromatography

This study presents the results obtained from qualitative and quantitative analysis of gallic acid from hydro-alcoholic extracts (methanol, ethanol) of plants from Plantae regnum. Plant qualitative analysis was performed using a novel mass spectrometric (MS) method based on fully automated chip-nanoelectrospray ionization (nanoESI) high capacity ion trap (HCT) while quantitative analysis was carried out by high performance liquid chromatography (HPLC). These methods were applied to Alchemilla vulgaris — common lady’s-mantle (aerial part), Allium ursinum — bear’s garlic (leaves), Acorus calamus — common sweet flag (roots), Solidago virga-aurea — goldenrod (aerial part). Obtained results indicated that methanol extracts (96%, 80%) have a gallic acid content ranging between 0.0011–0.0576 mg mL⁻¹ extract while the ethanol extracts (96%, 60%) exhibit a gallic acid concentration that varies between 0.0010–0.0182 mg mL⁻¹ extract.      

Improved spectrofluorimetric methods for determination of penicillamine in capsules

Two simple, sensitive and specific fluorimetric methods have been developed for the determination of Penicillamine (PNC), a sulphur containing compound. Method (I) involves the reaction of PNC with 2′,7′-bis(acetoxymercuri)-fluorescein (AMF) in the presence of Kolthoff’s buffer, pH 8.2, with subsequent measurement of fluorescence spectra at 520 nm (λ_Ex 497 nm). Method (II) is based on PNC being oxidized into penicillaminic acid using Cerium (IV) in an acidic medium. Method sensitivity has been improved using sodium triphosphate which enhances the luminescence intensity of Ce(III). Fluorescence spectra were then measured at 348 nm (λ_Ex 293 nm). The reaction conditions and the fluorescence spectral properties have been investigated for both methods. Under the described conditions, the proposed methods were applicable over the concentration ranges 0.0048 − 0.0288 μg mL⁻¹ and 0.096 − 0.288 μg mL⁻¹ with mean percentage recoveries 99.95 ± 1.29 and 100.04 ± 1.10 for methods I and II, respectively. The proposed methods were validated in terms of accuracy, precision, LOD and LOQ and robustness and then were successfully applied to the determination of PNC in bulk powder and in capsules as well as in the presence of the related disulphide. The results obtained were determined to be in good agreement with those obtained using a previously reported method.      

Determination of europium by using the chemical oscillating system of Ce(IV)-KBrO<Subscript>3</Subscript>-acetone-oxalic acid-H<Subscript>2</Subscript>SO<Subscript>4</Subscript>

A sensitive and convenient method for the determination of trace europium ions using an oscillating chemical reaction involving Ce(IV) - KBrO₃ - acetone - oxalic acid - H₂SO₄ was proposed. The results indicated that the changes in oscillating period (T) was linearly proportional to the negative logarithmic concentration of Eu³⁺ (-log C) in the range of 1.41 × 10⁻⁸ ˜ 1.41 × 10⁻⁴ mol L⁻¹ (r = 0.9982) with a detection limit of 1.04 × 10⁻⁹ mol L⁻¹. The recoveries were limited to the range of 99.5% to 100.8%. Under the same conditions, other rare earth ions did not interfere with the determination of Eu³⁺. In addition, a perturbation mechanism was also discussed briefly.      

Kinetic spectrophotometric determination of hydrazine

A kinetic spectrophotometric method for hydrazine determination in the range of 9.36×10⁻⁷ to 4.37×10⁻⁵ mol dm⁻³, based on the inhibitory effect of hydrazine on the oxidation of Victoria Blue 4- R by KBrO₃, was developed and validated. Kinetic parameters are reported for both the indicating and the inhibiting reaction. The detection limit was established as 9.98×10⁻⁸ mol dm⁻³. The selectivity of the proposed method was tested considering the influence of different ions that may be present in real samples. The method was successfully applied for hydrazine determination in various samples (very pure water from the water-steam system of a power plant and Isoniazid tablets, a pharmaceutical product).      

Immobilization of quaternary ammonium salts on silica gel for perchlorate ions removal

Silica surface was modified with quaternary ammonium salts to give three matrices of different chain length. The synthesized supports were characterized by elemental analysis and infrared spectroscopy, as well as scanning electron microscopy and semi-empirical parametric method 5. Their exchange capacities for ClO₄ ⁻, F⁻, NO₃ ⁻ and CH₃COO⁻ ions were investigated by conductometric titration. The amount of exchanged chloride ions from the matrix was studied for different initial anions concentration. The functionalized silica gel showed very good ability of perchlorate ions exchange from the water solution in room temperature. The anion-exchange properties were also studied in comparison to different number of reactive sites in the matrices. The increased number of chloride at the silica surface took effect on increased ability of ClO₄ ⁻ anion exchange