Thickness study of Al:ZnO film for application as a window layer in Cu(In1−xGax)Se2 thin film solar cell

Structural, electrical and optical properties of Al doped ZnO (Al:ZnO) thin film of various thicknesses, grown by radio-frequency magnetron sputtering system were studied in relation to the application as a window layer in Cu(In_1−xGa_x)Se₂ (CIGS) thin film solar cell. It was found that the electrical and structural properties of Al:ZnO film improved with increasing its thickness, however, the optical properties degraded. The short circuit current density, J_sc of the fabricated CIGS based solar cells was significantly influenced by the variation of the Al:ZnO window layer thickness. Best efficiency was obtained when CIGS solar cell was fabricated with electrically and optically optimized Al:ZnO window layer.     

Electroreflectance study of CuIn1−xGaxSe2 thin film solar cells

We have investigated the optical properties of CuIn_1−xGa_xSe₂ (CIGS) thin film solar cells using their electroreflectance (ER) at room temperature. The ER spectra exhibited one broad and two narrow signal regions. Using the photoluminescence (PL) and photocurrent (PC) spectra, the peaks in the low-energy region (1.02–1.35 eV) can be assigned to the CIGS thin film. The PC results implied that the peaks in the high-energy region (2.10–2.52 eV) can be assigned to the CdS band-gap energy. Using the applied bias voltage, the broad signals in the 1.35–2.09 eV region can be assigned to the Franz–Keldysh oscillation (FKO) due to the internal electric field. The ER spectra exhibited a distorted CdS signal for the CIGS thin film solar cell with low shunt resistance and efficiency.     

Growth of InN films and nanorods by H-MOVPE

InN films and nanorods were grown by hydride metalorganic vapor phase epitaxy (H-MOVPE) and the effects of growth temperature, and NH₃/TMIn and HCl/TMIn ratios on morphological dependences were studied. The growth habit of InN varied from thin film to microrod to nanorod to no deposition as the growth conditions were changed about transition from growth to etching conditions. The growth and etch regimes were also predicted by chemical equilibrium calculations of In–C–H–Cl–N-inert system. The optical properties of InN nanorods and columnar structured films were measured by room temperature PL and a maximum intensity was observed at 1.08 eV for both structures.     

Characterization of electrodeposited Bi2S3 thin films by holographic interferometry

Optical non destructive evaluation methods, using lasers as the object illumination source, include holographic interferometry. It is widely used to measure stress, strain, and vibration in engineering structures. Double exposure holographic interferometry (DEHI) technique is used to determine thickness and stress of electrodeposited bismuth trisulphide (Bi₂S₃) thin films for various deposition times. The same is tested for other concentration of the precursors. It is observed that, increase in deposition time, increases thickness of thin film but decreases stress to the substrate. The structural, optical and surface wettability properties of the as deposited films have been studied using X-ray diffraction (XRD), optical absorption and contact angle measurement, respectively. The X-ray diffraction study reveals that the films are polycrystalline with orthorhombic crystal structure. Optical absorption study shows the presence of direct transition with band bap 1.78 eV. The water contact angle measurement shows hydrophobic nature of Bi₂S₃ thin film surface.     

Controlled growth of standing Ag nanorod arrays on bare Si substrate using glancing angle deposition for self-cleaning applications

A facile approach to manipulate the hydrophobicity of surface by controlled growth of standing Ag nanorod arrays is presented. Instead of following the complicated conventional method of the template-assisted growth, the morphology or particularly average diameter and number density (nanorods cm^?2) of nanorods were controlled on bare Si substrate by simply varying the deposition rate during glancing angle deposition. The contact angle measurements showed that the evolution of Ag nanorods reduces the surface energy and makes an increment in the apparent water contact angle compared to the plain Ag thin film. The contact angle was found to increase for the Ag nanorod samples grown at lower deposition rates. Interestingly, the morphology of the nanorod arrays grown at very low deposition rate (1.2 Å?sec^?1) results in a self-cleaning superhydrophobic surface of contact angle about 157° and a small roll-off angle about 5°. The observed improvement in hydrophobicity with change in the morphology of nanorod arrays is explained as the effect of reduction in solid fraction within the framework of Cassie–Baxter model. These self-cleaning Ag nanorod arrays could have a significant impact in wide range of applications such as anti-icing coatings, sensors and solar panels.     

Cu2ZnSn(S1–xSex)4 thin film solar cells prepared by water‐based solution process

The kesterite Cu₂ZnSn(S_1–xSe_x)₄ (CZTSSe) thin film solar cell has been developed rapidly due to its excellence in structural and optical properties and its abundance in raw materials. Both vacuum‐based and solution‐based methods have been successfully employed to fabricate CZTSSe thin film solar cells. In this Letter, we report an environmentally friendly, water‐based, solution process for fabrication of high‐efficiency CZTSSe thin film solar cells. High quality CZTSSe thin film is obtained by selenization under high temperature and Se vapor. An efficiency of 6.2% is achieved on CZTSSe thin film solar cell fabricated by such water‐based solution process. (© 2014 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Synthesis and Characteristics of Electrodeposited CoxZn1-x Nanorods

CoxZn1-x nanorod arrays were fabricated by electrodeposition in porous anodic aluminum oxide templates at different electric potentials. X-ray diffraction and transmission electron microscopy indicate that highly-ordered and uniform nanorods have been fabricated. The amounts of Co and Zn contents are investigated using energy dispersive spectroscopy, which demonstrates that the atom ratio of the alloy nanorods changes with the deposition potential. In addition, magnetic measurements show that the magnetic isotropy Co-rich CoZn nanorods will change to magnetic anisotropy nanorods with the easy axis parallel to the rod long axis with decreasing Co content.     

Synthesis and characterization of TiO2/Fe2O3 core-shell nanocomposition film and their photoelectrochemical property

TiO₂/Fe₂O₃ core-shell nanocomposition film has been fabricated via two-step method. TiO₂ nanorod arrays are synthesized by a facile hydrothermal method, and followed by Fe₂O₃ nanoparticles deposited on TiO₂ nanorod arrays through an ordinary chemical bath deposition. The phase structures, morphologies, particle size, chemical compositions of the composites have been characterized by X-ray diffraction (XRD), field emission scanning electron microscope (FESEM) and ultraviolet-visible (UV-vis) spectrophotometer. The results confirm that Fe₂O₃ nanoparticles of mean size ca. 10 nm coated on the surface of TiO2 NRs. After depositing Fe₂O₃, UV-vis absorption property is induces the shift to the visible-light range, the annealing temperature of 600 °C is the best condition for UV-vis absorption property of TiO₂/Fe₂O₃ nanocomposite film, and increasing Fe content, optical activity are enhanced one by one. The photoelectrochemical (PEC) performances of the as-prepared composite nanorods are determined by measuring the photo-generated currents under illumination of UV-vis light. The TiO₂ NRs modified by Fe₂O₃ show the photocurrent value of 1.36 mA/cm² at 0 V vs Ag/AgCl, which is higher than those of unmodified TiO₂ NRs.     

The effect of TiO<Subscript>2</Subscript> coating on the electrochemical performance of ZnO nanorod as the anode material for lithium-ion battery

ZnO nanorods were coated with TiO₂ thin film using the atomic layer deposition (ALD) process. X-ray diffraction, scanning electron microscopy, and transmission electron microscopy were used to characterize the crystal structure and surface morphology of the coated composites. Results of galvanostatic charge and discharge tests and cyclic voltammograms suggest that lithium ions can reversibly intercalate into and deintercalate from TiO₂-coated ZnO nanorods, and that stable cycling behavior in an ethylene carbonate-based electrolyte can be achieved. The TiO₂ coating is believed to reduce the degree of reaction electrodes have with the electrolyte during the charge–discharge process since the inactive coating layer prevents the electrode from having direct contact with the electrolyte. Furthermore, the one-dimensional nanorods provide a relatively higher surface area than those of their bulk form or thin film, which allows a much greater portion of atoms on the surface to undergo the electrochemical reaction. The electrochemical study indicates that the TiO₂-coated ZnO nanorod arrays might be a candidate for the anode material in Li-ion batteries.     

Enhancement of optical absorption in amorphous silicon thin film solar cells with periodical nanorods to increase optical path length

In this paper, we demonstrate an amorphous silicon (a-Si) thin film solar cell (TFSC) with a homogeneous layer of a-Si to absorb short wavelength photons and periodical a-Si nanorod structures for light trapping enhancement for longer wavelength photons. In such a design, the total absorption can be greatly improved. The periodicity and duty ratio of the nanorods were optimized to enhance the total optical absorption within 500 nanometer (nm) to 1000 nm in the hybrid TFSC structure. The best overall absorption can be achieved when period of nanorods is about 500 nm. When the duty ratio of nanorods is 0.6, the average absorption can reach 80% which represents an improvement by 40% compared to the conventional thin film a-Si solar cell without nanorod structures.     

Spectroscopic analysis of CIGS2/CdS thin film solar cell heterojunctions on stainless steel foil

This paper presents a spectroscopic analysis of the interface between a CuIn_1−xGa_xS₂ (CIGS2) absorber and a CdS buffer layer on stainless steel foil by Auger electron spectroscopy (AES), inverse photoemission spectroscopy (IPES) and photoelectron spectroscopy (PES) such as X-ray photoelectron spectroscopy (XPS), and ultraviolet photoelectron spectroscopy (UPS). By combining these spectroscopic techniques, detailed information about the electronic and chemical properties of the CIGS2 surface and the CdS/CIGS2 interface can be obtained. The gallium concentration in CIGS2 films was found to increase continuously towards the Mo back contact. XPS analysis showed the presence of KCO₃ on the surface of CdS, deposited on etched and un-oxidized samples indicating diffusion of potassium. No potassium was observed on oxidized as well as samples having thicker CdS (50 nm) indicating the effectiveness of oxidation and chemical bath deposition (CBD) process in cleaning the sample surface effectively. In addition, investigation of the electronic level alignment at the interface has been carried out by combining PES and IPES. Conduction band offset of −0.45 (±0.15) eV and a valence band offset of −1.06 (±0.15) eV were measured. These unfavorable conditions limit efficiency of CIGS2 thin film solar cells.     

Diamond cubic Sn-rich nanocrystals: synthesis, microstructure and optical properties

Diamond cubic Sn-rich nanocrystals were fabricated with radii less than 20 nm by post-growth annealing at T=750 °C of Sn_xGe_1-x alloys grown on Ge(001) by molecular beam epitaxy. The crystal phase of the Sn-rich nanocrystals was determined to be diamond cubic from Fourier transform analysis of high-resolution transmission electron microscopy images. Optical transmittance of these Sn_xGe_1-x/Ge (001) films demonstrated changes in optical absorption that can be attributed to absorption from the nanocrystals. The energy bandgap was measured to be 0.45 eV for nanocrystals arrays in Ge with a mean diameter of 32 nm. PACS 68.37.Lp; 78.67.Hc; 81.07.Ta; 81.16.Dn; 68.65.Hb     

Large‐area Ag nanorod array substrates for SERS: AAO template‐assisted fabrication,functionalization, and application in detection PCBs

Highly ordered arrays of thiolated β‐cyclodextrin (HS‐β‐CD) functionalized Ag‐nanorods (Ag‐NRs) with plasmonic antennae enhancement of electrical field have been achieved for encapsulation and rapid detection of polychlorinated biphenyls (PCBs). The large‐area ordered arrays of rigid Ag‐NRs supported on copper base were fabricated via porous anodic aluminum oxide (AAO) template‐assisted electrochemical deposition. The inter‐nanorod gaps between the neighboring Ag‐NRs were tuned to sub‐10 nm by thinning the pore‐wall thickness of the AAO template using diluted H₃PO₄. The nearly perfect large‐area ordered arrays of Ag‐NRs supported on copper base render these systems excellent in surface‐enhanced Raman scattering (SERS) performance with uniform electric field enhancement, as testified by the SERS spectra and Raman mappings of rhodamine 6 G. Furthermore, the Ag‐NRs were functionalized with HS‐β‐CD molecules so as to capture the apolar PCB molecules in the hydrophobic cavity of the CD. Compared to the ordinary undecorated SERS substrates, the HS‐β‐CD modified Ag‐NR arrays exhibit better capture ability and higher sensitivity in rapid detection of PCBs. Copyright © 2012 John Wiley & Sons, Ltd.     

Improving light trapping and conversion efficiency of amorphous silicon solar cell by modified and randomly distributed ZnO nanorods

Three-dimensional （3D） nanostructures in thin film solar cells have attracted significant attention due to their appli- cations in enhancing light trapping. Enhanced light trapping can result in more effective absorption in solar cells, thus leading to higher short-circuit current density and conversion efficiency. We develop randomly distributed and modified ZnO nanorods, which are designed and fabricated by the following processes： the deposition of a ZnO seed layer on sub- strate with sputtering, the wet chemical etching of the seed layer to form isolated islands for nanorod growth, the chemical bath deposition of the ZnO nanorods, and the sputtering deposition of a thin Al-doped ZnO （ZnO：Al） layer to improve the ZnO/Si interface. Solar cells employing the modified ZnO nanorod substrate show a considerable increase in solar energy conversion efficiency.     

The SERS response of semiordered Ag nanorod arrays fabricated by template oblique angle deposition

Semiordered Ag nanorod arrays are fabricated by template oblique angle deposition (OAD) using regular Au nano‐post arrays with different diameters as seed patterns. The Au nano‐post arrays do not give an observable surface‐enhanced Raman scattering (SERS) activity under our detection configuration, whereas the patterned Ag nanorod arrays can produce a very strong SERS signal. These SERS intensities increase monotonically with the decrease in the diameter and separation of the Ag nanorods, which demonstrates that one can improve the SERS detection by tuning the diameter and separation of the Ag nanorods, and the template OAD method can help produce more uniform, reproducible, and sensitive Ag nanorod SERS substrates. Copyright © 2010 John Wiley & Sons, Ltd.     

Ellipsometric analysis and optical absorption characterization of gallium phosphide nanoparticulate thin film

Gallium phosphide (GaP) nanoparticulate thin films were easily fabricated by colloidal suspension deposition via GaP nanoparticles dispersed in N,N-dimethylformamide. The microstructure of the film was performed by x-ray diffraction, high resolution transmission electron microscopy and field emission scanning electron microscopy. The film was further investigated by spectroscopic ellipsometry. After the model GaP+void|SiO₂ was built and an effective medium approximation was adopted, the values of the refractive index n and the extinction coefficient k were calculated for the energy range of 0.75 eV-4.0 eV using the dispersion formula in DeltaPsi2 software. The absorption coefficient of the film was calculated from its k and its energy gaps were further estimated according to the Tauc equation, which were further verified by its fluorescence spectrum measurement. The structure and optical absorption properties of the nanoparticulate films are promising for their potential applications in hybrid solar cells.     

Cu(In,Ga)Se2 superstrate-type solar cells with Zn1−xMgxO buffer layers

Superstrate-type Cu(In,Ga)Se₂ (CIGS) thin film solar cells were fabricated using Zn_1−xMg_xO buffer layers. Due to the diffusion of Cd into CIGS during the growth of the CIGS layer, the conventional buffer material of CdS is not suitable. ZnO is a good candidate because of higher thermal tolerance but the conduction band offset (CBO) of ZnO/CIGS is not appropriate. In this study, the Zn_1−xMg_xO buffer layers were used to fulfill both the requirements. The superstrate-type solar cells with a soda-lime glass/In₂O₃:Sn/Zn_1−xMg_xO/CIGS/Au structure were fabricated with different band gap energies of the Zn_1−xMg_xO layer. The CIGS layers [Ga/(In + Ga)∼0.25] were deposited by co-evaporation method. The substrate temperature during the CIGS deposition of 450 °C did not cause the intermixing of the Zn_1−xMg_xO and CIGS layers. The conversion efficiency of the cell with Zn_1−xMg_xO was higher than that with ZnO due to the improvement of open-circuit voltage and shunt resistance. The results well corresponded to the behavior of the adjustment of CBO, demonstrating that the usefulness of the Zn_1−xMg_xO layer for the CBO control in the superstrate-type CIGS solar cells.     

Swift heavy ion induced modifications in cobalt doped ZnO thin films: Structural and optical studies

Modifications in the structural and optical properties of 100 MeV Ni⁷⁺ ions irradiated cobalt doped ZnO thin films (Zn_1−xCo_xO, x = 0.05) prepared by sol-gel route were studied. The films irradiated with a fluence of 1 × 10¹³ ions/cm² were single phase and show improved crystalline structure with preferred C-axis orientation as revealed from XRD analysis. Effects of irradiation on bond structure of thin films were studied by FTIR spectroscopy. The spectrum shows no change in bonding structure of Zn-O after irradiation. Improved quality of films is further supported by FTIR studies. Optical properties of the pristine and irradiated samples have been determined by using UV-vis spectroscopic technique. Optical absorption spectra show an appreciable red shift in the band gap of irradiated Zn_1−xCo_xO thin film due to sp-d interaction between Co²⁺ ions and ZnO band electrons. Transmission spectra show absorption band edges at 1.8 eV, 2.05 eV and 2.18 eV corresponding to d-d transition of Co²⁺ ions in tetrahedral field of ZnO. The AFM study shows a slight increase in grain size and surface roughness of the thin films after irradiation.     

Influence of the core‐hole effect on optical properties of magnesium oxide (MgO) near the Mg L‐edge region

The influence of the core‐hole effect on optical properties of magnesium oxide (MgO) is established through experimental determination of optical constants and first‐principles density functional theory studies. Optical constants (δ and β) of MgO thin film are measured in the spectral region 40–300 eV using reflectance spectroscopy techniques at the Indus‐1 synchrotron radiation source. The obtained optical constants show strong core exciton features near the Mg L‐edge region, causing significant mismatch with Henke's tabulated values. On comparing the experimentally obtained optical constants with Henke's tabulated values, an edge shift of ～3.0 eV is also observed. Distinct evidence of effects of core exciton on optical constants (δ and β) in the near Mg L‐edge absorption spectra are confirmed through first‐principles simulations.     

Annealing effect on the structural and optical properties of a Cd1−xZnxS thin film for photovoltaic applications

Herein is a report of a study on a Cd_1−xZn_xS thin film grown on an ITO substrate using a chemical bath deposition technique. The as-deposited films were annealed in air at 400 °C for 30 min. The composition, surface morphology and structural properties of the as-deposited and annealed Cd_1−xZn_xS thin films were studied using EDX, SEM and X-ray diffraction techniques. The annealed films have been observed to possess a crystalline nature with a hexagonal structure. The optical absorption spectra were recorded within the range of 350-800 nm. The band gap of the as-deposited thin films varied from 2.46 to 2.62 eV, whereas in the annealed film these varied from 2.42 to 2.59 eV. The decreased band gap of the films after annealing was due to the improved crystalline nature of the material.