19.4%‐efficient large‐area fully screen‐printed silicon solar cells

We demonstrate industrially feasible large‐area solar cells with passivated homogeneous emitter and rear achieving energy conversion efficiencies of up to 19.4% on 125 × 125 mm² p‐type 2–3 Ω cm boron‐doped Czochralski silicon wafers. Front and rear metal contacts are fabricated by screen‐printing of silver and aluminum paste and firing in a conventional belt furnace. We implement two different dielectric rear surface passivation stacks: (i) a thermally grown silicon dioxide/silicon nitride stack and (ii) an atomic‐layer‐deposited aluminum oxide/silicon nitride stack. The dielectrics at the rear result in a decreased surface recombination velocity of S_rear = 70 cm/s and 80 cm/s, and an increased internal IR reflectance of up to 91% corresponding to an improved J_sc of up to 38.9 mA/cm² and V_oc of up to 664 mV. We observe an increase in cell efficiency of 0.8% absolute for the cells compared to 18.6% efficient reference solar cells featuring a full‐area aluminum back surface field. To our knowledge, the energy conversion efficiency of 19.4% is the best value reported so far for large area screen‐printed solar cells. (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Study of hydrogenated AlN as an anti‐reflective coating and for the effective surface passivation of silicon

Stacks of aluminum oxide and silicon nitride are frequently used in silicon photovoltaics. In this Letter, we demonstrate that hydrogenated aluminum nitride can be an alternative to this dual‐layer stack. Deposited on 1 Ω cm p‐type FZ silicon, very low effective surface recombination velocities of 8 cm/s could be reached after firing at 820 °C. This excellent passivation is traced back to a high density of fixed charges at the interface of approximately –1 × 10¹² cm^–2 and a very low interface defect density below 5 × 10¹⁰ eV^–1 cm^–2. Furthermore, spectral ellipsometry measurements reveal that these aluminum nitride layers have ideal optical properties for use as anti‐reflective coatings. (© 2013 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Plasma hydrogenated,reactively sputtered aluminium oxide for silicon surface passivation

The intentional addition of hydrogen during reactive sputtering of AlO_x films has led to a dramatic improvement of the surface passivation of crystalline silicon wafers achieved with this technique. The 5 ms effective minority carrier lifetime measured on 1.5 Ω cm n‐type CZ silicon wafers is close to the 6 ms of a control wafer coated by atomic layer deposition (ALD) of AlO_x. Hydrogen‐sputtered films also provide excellent passivation of 1 Ω cm p‐type silicon, as demonstrated by an effective lifetime of 1.1 ms. It is likely that the improved passivation is related to the formation of an interfacial silicon oxide layer, as indicated by FTIR measurements. (© 2013 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Excellent passivation of thin silicon wafers by HF‐free hydrogen plasma etching using an industrial ICPECVD tool

In this work, hydrogen plasma etching of surface oxides was successfully accomplished on thin (～100 µm) planar n‐type Czochralski silicon wafers prior to intrinsic hydrogenated amorphous silicon [a‐Si:H(i)] deposition for heterojunction solar cells, using an industrial inductively coupled plasma‐enhanced chemical vapour deposition (ICPECVD) platform. The plasma etching process is intended as a dry alternative to the conventional wet‐chemical hydrofluoric acid (HF) dip for solar cell processing. After symmetrical deposition of an a‐Si:H(i) passivation layer, high effective carrier lifetimes of up to 3.7 ms are obtained, which are equivalent to effective surface recombination velocities of 1.3 cm s^–1 and an implied open‐circuit voltage (V_oc) of 741 mV. The passivation quality is excellent and comparable to other high quality a‐Si:H(i) passivation. High‐resolution transmission electron microscopy shows evidence of plasma‐silicon interactions and a sub‐nanometre interfacial layer. Using electron energy‐loss spectroscopy, this layer is further investigated and confirmed to be hydrogenated suboxide layers. (© 2015 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

Effective surface passivation of crystalline silicon using ultrathin Al2O3 films and Al2O3/SiNx stacks

We measure surface recombination velocities (SRVs) below 10 cm/s on p‐type crystalline silicon wafers passivated by atomic–layer–deposited (ALD) aluminium oxide (Al₂O₃) films of thickness ≥10 nm. For films thinner than 10 nm the SRV increases with decreasing Al₂O₃ thickness. For ultrathin Al₂O₃ layers of 3.6 nm we still attain a SRV < 22 cm/s on 1.5 Ω cm p‐Si and an exceptionally low SRV of 1.8 cm/s on high‐resistivity (200 Ω cm) p‐Si. Ultrathin Al₂O₃ films are particularly relevant for the implementation into solar cells, as the deposition rate of the ALD process is extremely low compared to the frequently used plasma‐enhanced chemical vapour deposition of silicon nitride (SiN_x). Our experiments on silicon wafers passivated with stacks composed of ultrathin Al₂O₃ and SiN_x show that a substantially improved thermal stability during high‐temperature firing at 830 °C is obtained for the Al₂O₃/SiN_x stacks compared to the single‐layer Al₂O₃ passivation. Al₂O₃/SiN_x stacks are hence ideally suited for the implementation into industrial‐type silicon solar cells where the metal contacts are made by screen‐printing and high‐temperature firing of metal pastes. (© 2009 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Excellent Si surface passivation by low temperature SiO2 using an ultrathin Al2O3 capping film

It is demonstrated that the application of an ultrathin aluminum oxide (Al₂O₃) capping film can improve the level of silicon surface passivation obtained by low‐temperature synthesized SiO₂ profoundly. For such stacks, a very high level of surface passivation was achieved after annealing, with S_eff < 2 cm/s for 3.5 Ω cm n‐type c‐Si. This can be attributed primarily to a low interface defect density (D_it < 10¹¹ eV^–1 cm^–2). Consequently, the Al₂O₃ capping layer induced a high level of chemical passivation at the Si/SiO₂ interface. Moreover, the stacks showed an exceptional stability during high‐temperature firing processes and therefore provide a low temperature (≤400 °C) alternative to thermally‐grown SiO₂. (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Plasma enhanced atomic layer deposition of gallium oxide on crystalline silicon: demonstration of surface passivation and negative interfacial charge

Herein we report on the passivation of crystalline silicon by gallium oxide (Ga₂O₃) using oxygen plasma as the oxidizing reactant in an atomic layer deposition (ALD) process. Excess carrier lifetimes of 2.1 ms have been measured on 1.75 Ω cm p‐type silicon, from which a surface recombination current density J₀ of 7 fA cm^–2 is extracted. From high frequency capacitance‐voltage (HF CV) measurements it is shown that, as in the case of Al₂O₃, the presence of a high negative charge density Q_tot/q of up to –6.2 × 10¹² cm^–2 is one factor contributing to the passivation of silicon by Ga₂O₃. Defect densities at midgap on the order of ～5 × 10¹¹ eV^–1 cm^–2 are extracted from the HF CV data on samples annealed at 300 °C for 30 minutes in a H₂/Ar ambient, representing an order of magnitude reduction in the defect density compared to pre‐anneal data. Passivation of a boron‐diffused p⁺ surface (96 Ω/□) is also demonstrated, resulting in a J₀ of 52 fA cm^–2. (© 2015 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

Surface passivation of crystalline silicon by sputter deposited hydrogenated amorphous silicon

This letter shows that intrinsic hydrogenated amorphous silicon (a‐Si:H) films deposited by RF magnetron sputtering can provide outstanding passivation of crystalline silicon surfaces, similar to that achieved by plasma enhanced chemical vapour deposition (PECVD). By using a 2% hydrogen and 98% argon gas mixture as the plasma source, 1.5 Ω cm n‐type FZ silicon wafers coated with sputtered a‐Si:H films achieved an effective lifetime of 3.5 ms, comparable to the 3 ms achieved by PECVD (RF and microwave dual‐mode). This is despite the fact that Fourier transform infrared spectroscopy measurements show that sputtering and PECVD deposited films have very different chemical bonding configurations. We have found that film thickness and deposition temperature have a significant impact on the passivation results. Self‐annealing and hydrogen plasma treatment during deposition are likely driving forces for the observed changes in surface passivation. These experimental results open the way for the application of sputtered a‐Si:H to silicon heterojunction solar cells. (© 2014 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Silicon nitride/silicon oxide interlayers for solar cell passivating contacts based on PECVD amorphous silicon

This Letter demonstrates improved passivating contacts for silicon solar cells consisting of doped silicon films together with tunnelling dielectric layers. An improvement is demonstrated by replacing the commonly used silicon oxide interfacial layer with a silicon nitride/silicon oxide double interfacial layer. The paper describes the optimization of such contacts, including doping of a PECVD intrinsic a‐Si:H film by means of a thermal POCl₃ diffusion process and an exploration of the effect of the refractive index of the SiN_x. The n⁺ silicon passivating contact with SiN_x /SiO_x double layer achieves a better result than a single SiN_x or SiO_x layer, giving a recombination current parameter of ～7 fA/cm² and a contact resistivity of ～0.005 Ω cm², respectively. These self‐passivating electron‐selective contacts open the way to high efficiency silicon solar cells. (© 2015 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

Surface passivation schemes for high‐efficiency n‐type Si solar cells

An effective passivation on the front side boron emitter is essential to utilize the full potential of solar cells fabricated on n‐type silicon. However, recent investigations have shown that it is more difficult to achieve a low surface recombination velocity on highly doped p‐type silicon than on n‐type silicon. Thus, the approach presented in this paper is to overcompensate the surface of the deep boron emitter locally by a shallow phosphorus diffusion. This inversion from p‐type to n‐type surface allows the use of standard technologies which are used for passivation of highly doped n‐type surfaces. Emitter saturation current densities (J_0e) of 49 fA/cm² have been reached with this approach on SiO₂ passivated lifetime samples. On solar cells a certified conversion efficiency of 21.7% with an open‐circuit voltage (V_oc) of 676 mV was achieved. (© 2008 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Influence of precursor gas ratio and firing on silicon surface passivation by APCVD aluminium oxide

Using a high throughput, in‐line atmosphere chemical vapor deposition (APCVD) tool, we have synthesized amorphous aluminum oxide (AlO_x) films from precursors of trimethyl‐aluminum (TMA) and O₂, yielding a maximum deposition 150 nm min^–1 per wafer. For p‐type crystalline silicon (c‐Si) wafers, excellent surface passivation was achieved with the APCVD AlO_x films, with a best maximum effective surface recombination velocity (S_eff,max) of 8 cm/s following a standard industrial firing step. The findings could be attributed to the existence of large negative charge (Q_f ≈ –3 × 10¹² cm^–2) and low interface defect density (D_it ≈ 4 × 10¹¹ eV^–1 cm^–2) achieved by the films. This data demonstrates a high potential for APCVD AlO_x to be used in high efficiency, low cost industrial solar cells. (© 2013 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Temporary Surface Passivation for Characterisation of Bulk Defects in Silicon: A Review

Accurate measurements of the bulk minority carrier lifetime in high‐quality silicon materials is challenging due to the influence of surface recombination. Conventional surface passivation processes such as thermal oxidation or dielectric deposition often modify the bulk lifetime significantly before measurement. Temporary surface passivation processes at room or very low temperatures enable a more accurate measurement of the true bulk lifetime, as they limit thermal reconfiguration of bulk defects and minimize bulk hydrogenation. In this article we review the state‐of‐the‐art for temporary passivation schemes, including liquid immersion passivation based upon acids, halogen‐alcohols and benzyl‐alcohols, and thin film passivation usually based on organic substances. We highlight how exceptional surface passivation (surface recombination velocity below 1 cm s^?1) can be achieved by some types of temporary passivation. From an extensive review of available data in the literature, we find p‐type silicon can be best passivated by hydrofluoric acid containing solutions, with superacid‐based thin films showing a slight superiority in the n‐type case. We review the practical considerations associated with temporary passivation, including sample cleaning, passivation activation, and stability. We highlight examples of how temporary passivation can assist in the development of improved silicon materials for photovoltaic applications, and provide an outlook for the future of the field.

     

Role of a‐Si:H bulk in surface passivation of c‐Si wafers

The low thermal stability of hydrogenated amorphous silicon (a‐Si:H) thin films limits their widespread use for surface passivation of c‐Si wafers on the rear side of solar cells. We show that the thermal stability of a‐Si:H surface passivation is increased significantly by a hydrogen rich a‐Si:H bulk, which acts as a hydrogen reservoir for the a‐Si:H/c‐Si interface. Based on this mechanism, an excellent lifetime of 5.1 ms (at injection level of 10¹⁵ cm^–3) is achieved after annealing at 450 °C for 10 min. (© 2010 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Enhanced rear‐side reflection and firing‐stable surface passivation of silicon solar cells with capping polymer films

Low refractive index polymer materials have been investigated with a view to form the back surface mirror of advanced silicon solar cells. SiO_x:H or AlO_y SiO_x:H polymer films were spun on top of an ultra‐thin (<10 nm) atomic‐layer‐deposited (ALD) Al₂O₃ layer, itself deposited on low‐resistivity (1 Ω cm) p‐type crystalline silicon wafers. These double‐layer stacks were compared to both ALD Al₂O₃ single layers and ALD Al₂O₃/plasma‐enhanced chemical vapour deposited (PECVD) SiN_x stacks, in terms of surface passivation, firing stability and rear‐side reflection. Very low surface recombination velocity (SRV) values approaching 3 cm/s were achieved with ALD Al₂O₃ layers in the 4–8 nm range. Whilst the surface passivation of the single ALD Al₂O₃ layer is maintained after a standard firing step typical of screen printing metallisation, a harsher firing regime revealed an enhanced thermal stability of the ALD Al₂O₃/SiO_x:H and ALD Al₂O₃/AlO_y SiO_x:H stacks. Using simple two‐dimensional optical modelling of rear‐side reflection it is shown that the low refractive index exhibited by SiO_x:H and AlO_y SiO_x:H results in superior optical performance as compared to PECVD SiN_x, with gains in photogenerated current of ～0.125 mA/cm² at a capping thickness of 100 nm. (© 2013 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

All‐optical modulation based on silicon quantum dot doped SiOx:Si‐QD waveguide

All‐optical modulation based on silicon quantum dot doped SiO_x:Si‐QD waveguide is demonstrated. By shrinking the Si‐QD size from 4.3 nm to 1.7 nm in SiO_x matrix (SiO_x:Si‐QD) waveguide, the free‐carrier absorption (FCA) cross section of the Si‐QD is decreased to 8 × 10⁻¹⁸ cm² by enlarging the electron/hole effective masses, which shortens the PL and Auger lifetime to 83 ns and 16.5 ps, respectively. The FCA loss is conversely increased from 0.03 cm⁻¹ to 1.5 cm⁻¹ with the Si‐QD size enlarged from 1.7 nm to 4.3 nm due to the enhanced FCA cross section and the increased free‐carrier density in large Si‐QDs. Both the FCA and free‐carrier relaxation processes of Si‐QDs are shortened as the radiative recombination rate is enlarged by electron–hole momentum overlapping under strong quantum confinement effect. The all‐optical return‐to‐zero on‐off keying (RZ‐OOK) modulation is performed by using the SiO_x:Si‐QD waveguides, providing the transmission bit rate of the inversed RZ‐OOK data stream conversion from 0.2 to 2 Mbit/s by shrinking the Si‐QD size from 4.3 to 1.7 nm.     

Passivation of black silicon boron emitters with atomic layer deposited aluminum oxide

The nanostructured surface – also called black silicon (b‐Si) – is a promising texture for solar cells because of its extremely low reflectance combined with low surface recombination obtained with atomic layer deposited (ALD) thin films. However, the challenges in keeping the excellent optical properties and passivation in further processing have not been addressed before. Here we study especially the applicability of the ALD passivation on highly boron doped emitters that is present in crystalline silicon solar cells. The results show that the nanostructured boron emitters can be passivated efficiently using ALD Al₂O₃ reaching emitter saturation current densities as low as 51 fA/cm². Furthermore, reflectance values less than 0.5% after processing show that the different process steps are not detrimental for the low reflectance of b‐Si. (© 2013 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

21.63% industrial screen‐printed multicrystalline Si solar cell

In this paper, we demonstrate industrially feasible large‐area solar cells achieving energy conversion efficiency up to 21.63% on p‐type boron doped multicrystalline Si wafers. Advanced light trapping, passivation and hydrogenation technology are used to achieve excellent light absorption with very low surface recombination velocity. The bulk lifetime of the multi‐crystalline Si wafers used for the fabrication exceeds 500 μs after optimized gettering and hydrogenation processes. The high bulk lifetime and excellent surface passivation enable V_oc to exceed 670 mV. The metallization process is carried out by screen printing and firing in a conventional belt furnace. Detailed performance parameters and quantum efficiency of the cells will be illustrated in the paper. In addition, free energy loss analysis and cell simulation are also performed using the control parameters measured during cell fabrication processes.     

Theoretical investigation on the passivation layer with linearly graded bandgap for the amorphous/crystalline silicon heterojunction solar cell

Passivation layer with linearly graded bandgap (LGB) was proposed to improve the performance of amorphous/crystalline silicon heterojunction (SHJ) solar cell by eliminating the large abrupt energy band uncontinuity at the a‐Si:H/c‐Si interface. Theoretical investigation on the a‐Si:H(p)/the LGB passivation layer(i)/c‐Si(n)/a‐Si:H(i)/a‐Si:H(n⁺) solar cell via AFORS‐HET simulation show that such LGB passivation layer could improve the solar cell efficiency (η) by enhancing the fill factor (FF) greatly, especially when the a‐Si:H(p) emitter was not efficiently doped and the passivation layer was relatively thick. But gap defects in the LGB passivation layer could make the improvement discounted due to the open‐circuit voltage (V_OC) decrease induced by recombination. To overcome this, it was quite effective to keep the gap defects away from the middle of the bandgap by widening the minimum bandgap of the LGB passivation layer to be a little larger than that of the c‐Si base. The underlying mechanisms were analysed in detail. How to achieve the LGB passivation layer experimentally was also discussed. (© 2016 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

Mechanism for crystalline Si surface passivation by the combination of SiO2 tunnel oxide and µc‐SiC:H thin film

This work demonstrates that the combination of a wet‐chemically grown SiO₂ tunnel oxide with a highly‐doped microcrystalline silicon carbide layer grown by hot‐wire chemical vapor deposition yields an excellent surface passivation for phosphorous‐doped crystalline silicon (c‐Si) wafers. We find effective minority carrier lifetimes of well above 6 ms by introducing this stack. We investigated its c‐Si surface passivation mechanism in a systematic study combined with the comparison to a phosphorous‐doped polycrystalline‐Si (pc‐Si)/SiO₂ stack. In both cases, field effect passivation by the n‐doping of either the µc‐SiC:H or the pc‐Si is effective. Hydrogen passivation during µc‐SiC:H growth plays an important role for the µc‐SiC:H/SiO₂ combination, whereas phosphorous in‐diffusion into the SiO₂ and the c‐Si is operative for the surface passivation via the Pc‐Si/SiO₂ stack. The high transparency and conductivity of the µc‐SiC:H layer, a low thermal budget and number of processes needed to form the stack, and the excellent c‐Si surface passivation quality are advantageous features of µc‐SiC:H/SiO₂ that can be beneficial for c‐Si solar cells. (© 2016 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

Enhancement of photoluminescence intensity from Si nanodots using Al2O3 surface passivation layer grown by atomic layer deposition

Temperature-dependent photoluminescence (PL) from Si nanodots with Al₂O₃ surface passivation layers was studied. The Si nanodots were grown by low pressure chemical vapor deposition and the Al₂O₃ thin films were prepared by atomic layer deposition (ALD), respectively. The BOE (Buffer-Oxide-Etch) treatment resulted in the damaged surface of Si nanodots and thus caused dramatic reduction in the PL intensity. Significant enhancement of the PL intensity from Si nanodots after the deposition of Al₂O₃ thin films was observed over a wide temperature range, indicating the remarkable surface passivation effect to suppress the non-radiative recombination at the surface of Si nanodots. The results demonstrated that the Al₂O₃ surface passivation layers grown by ALD are effectually applicable to nanostructured silicon devices.