Growth and Characterization of [001] ZnO Nanorod Array on ITO Substrate with Electric Field Assisted Nucleation

This paper reports direct growth of [001] ZnO nanorod arrays on ITO substrate from aqueous solution with electric field assisted nucleation, followed with thermal annealing. X-ray diffraction analyses revealed that nanorods have wurtzite crystal structure. The diameter of ZnO nanorods was 60–300 nm and the length was up to 2.5 μm depending on the growth condition. Photoluminescence spectra showed a broad emission band spreading from 500 to 870 nm, which suggests that ZnO nanorods have a high density of oxygen interstitials. Low and nonlinear electrical conductivity of ZnO nanorod array was observed, which was ascribed to non-ohmic contact between top electrode and ZnO nanorods and the low concentration of oxygen vacancies.     

Pt纳米花/ZnO复合阵列的制备及对甲醇氧化催化的研究

利用调控ZnO纳米棒阵列的疏水、亲水性,由电化学方法制备了Pt纳米花/ZnO(PtNF/ZnO)复合阵列.该复合阵列排列规则、尺寸均一、方向一致.每一根ZnO纳米棒的顶端都覆盖着由Pt纳米颗粒构成的Pt纳米花,具有大的比表面积.与以亲水性的ZnO纳米棒制得的覆盖Pt纳米颗粒的ZnO复合阵列(PtNP/ZnO)以及单独的Pt颗粒相比,PtNF/ZnO复合阵列对甲醇氧化具有更高的电化学催化活性.     

Theoretical analysis of growth of ZnO nanorods on the amorphous surfaces

Semiconductor nanorod arrays on a substrate have a preferential alignment orientation that minimizes the excessive free energy of the system. In the case of wet chemically synthesized zinc oxide (ZnO) nanorod on the amorphous surfaces, the thermodynamic driving force determines the orientation to be normal to the surface. Among the various kinds of amorphous surfaces, the spherical seed layer composed of ZnO precursors gives isotropic radially aligned arrays. For other surfaces, such as wrinkled and planar ZnO precursor thin film, nanorod arrays are aligned to be perpendicular to the tangential line of the surface. The maximum value of the aspect ratio of the nanorod is determined by the thermodynamic relationship. The number density of nanorods per unit precursor particles decreases with increasing contact angle of the seed particles.     

Synthesis and field emission characteristics of bilayered ZnO nanorod array prepared by chemical reaction

The uniform, large-scale, and bilayered ZnO nanorod array on silicon substrate has been synthesized by a catalyst and template-free chemical reaction in a dilute solution. The effect of different precursor ZnO films on the morphology and size of the ZnO nanorod array has been investigated. Moreover, the morphology evolution of the ZnO nanorod array with the increase of reaction time indicates that the second growth is the reason for the decrease of the ZnO nanorod diameter and the formation of the bilayered ZnO nanorod array. Finally, the field emission from the ZnO nanorod array with different diameters is presented.     

Synthesis of perpendicular nanorod arrays with hierarchical architecture and water slipping superhydrophobic properties

The utilization of vertically aligned smooth gold nanorod arrays with and without nanoporous tip architectures as superhydrophobic surfaces is described. Nanoporous architecture was produced on the tips of nanorods by selectively dissolving less noble components from the alloy nanorods. The resulting nanoscopic dual-size roughness features enhanced the surface dewettability after surface modification with low-surface-energy materials such as long-chain normal alkanethiols and fluorinated organic compounds. The surface cleaning properties were also tested with a rolling water droplet.     

Robust Nonsticky Superhydrophobicity by the Tapering of Aligned ZnO Nanorods

The robust nonsticky superhydrophobicity of aligned nanoneedle films is reported. A facile, efficient, cheap, and available method based on the diffusion‐limited crystal growth principle is proposed for controlling the tapering of ZnO nanorods, the profiles of which can be tuned effectively by synergetic control over reaction time and temperature in an extremely strong alkaline reaction system. The synthesized nanoneedle, nanopencil, and nanorod arrays are chosen for studying the effects of nanoscale topography on anti‐droplet‐sticking ability. After silanization, all of them show excellent quasi‐static anti‐droplet‐stickiness, and water adhesion along the normal and lateral directions can be greatly reduced by the tapering of nanorods and eliminated by sharp nanoneedles. However, their antisticking stability is distinct under the droplet impact: the nanoneedle sample is still nonsticky but the nanorod sample loses its antisticking ability. Only ensuring the liquid/air interface is in the suspended nonwetting state is insufficient to obtain robust nonsticky surfaces, which also require extremely low solid–liquid van der Waals attraction.     

Self-assembly of synthetic hydroxyapatite nanorods into an enamel prism-like structure

The application of surfactants as reverse micelles or microemulsions for the synthesis and self-assembly of nanoscale structures is one of the most widely adopted methods in nanotechnology. These synthesized nanostructure assemblies sometimes have an ordered arrangement. The aim of this research was to take advantage of these latest developments in the area of nanotechnology to mimic the natural biomineralization process to create the hardest tissue in the human body, dental enamel. This is the outermost layer of the teeth and consists of enamel prisms, highly organized micro-architectural units of nanorod-like calcium hydroxyapatite (HA) crystals arranged roughly parallel to each other. In particular, we have synthesized and modified the hydroxyapatite nanorods surface with monolayers of surfactants to create specific surface characteristics which will allow the nanorods to self-assemble into an enamel prism-like structure at a water/air interface. The size of the synthetic hydroxyapatite nanorods can be controlled and we have synthesized nanorods similar in size to both human and rat enamel. The prepared nanorod assemblies were examined using transmission electron microscopy (TEM) and atomic force microscopy (AFM). The specific Langmuir-Blodgett films were shown to be comprised of enamel prism-like nanorod assemblies with a Ca/P ratio between 1.6 and 1.7.     

Template-based synthesis of nanorod, nanowire, and nanotube arrays

This review introduces and summarizes the fundamentals and various technical approaches developed for the template-based synthesis of nanorod, nanowire and nanotube arrays. After a brief introduction to various concepts for the growth of nanorods, nanowires and nanobelts, attention will be focused mainly on the most widely used and well established techniques for the template-based growth of nanorod arrays: electrochemical deposition, electrophoretic deposition, filling of templates by capillary force and centrifugation, and chemical conversion. In each section, relevant fundamentals will be first introduced, followed with examples to illustrate the specific details of each technique.     

CdS量子点敏化ZnO纳米棒阵列电极的制备和光电化学性能

采用连续式离子层吸附与反应法制备了CdS量子点敏化的ZnO纳米棒电极.应用扫描电子显微镜(SEM)、X射线衍射(XRD)和透射电子显微镜(TEM)对CdS量子点/ZnO纳米棒电极的形貌、晶型和颗粒尺寸进行了分析和表征;采用光电流-电位曲线和光电流谱研究了不同CdS循环沉积次数及不同沉积浓度对复合电极的光电性能影响.结果表明,前驱体浓度都为0.1mol·L-1且沉积15次敏化后的ZnO纳米棒阵列电极光电性能最好.与单纯的ZnO纳米棒阵列电极和单纯的CdS量子点电极相比,其光电转换效率显著提高,单色光光子-电流转换效率(IPCE)在380nm处达到76%.这是因为CdS量子点可以拓宽光的吸收到可见光区,并且在所形成的界面上光生载流子更容易分离.荧光光谱实验进一步说明了光电增强的原因是,两者间形成的界面中表面态大大减少,有利于减少光生电子和空穴的复合.     

基底对电沉积制备ZnO纳米棒阵列的影响

采用恒电位电沉积方法, 在未经修饰的ITO导电玻璃基底上通过控制实验条件制备出不同形貌的纳米ZnO结构, 而在经过ZnO纳米粒子膜修饰后的ITO导电玻璃基底上, 制备出透明、高取向、粒径小于30 nm的ZnO纳米棒阵列. 用扫描电子显微镜(SEM)、X射线衍射(XRD)以及透射光谱对制备出的ZnO纳米棒阵列的结构、形貌和透明性进行了表征. 测试结果表明, ZnO纳米棒阵列的平均直径为21 nm, 粒径分布窄, 约18～25 nm, 择优生长取向为[001]方向, 垂直于基底生长. 当入射光波长大于400 nm时, ZnO纳米棒阵列的透光率大于95%.     

水热法制备高度取向的氧化锌纳米棒阵列

氧化锌的激子结合能(60meV)及光增益系数(300cm^-1)比GaN的(25meV,100cm^-1)还高,这一特点使它成为紫外半导体激光发射材料的研究热点。最近,Yang等成功地观测到规则的ZnO纳米线阵列的激光发射现象,更加激起了人们合成一维高度有序ZnO纳米结构的热情,由于一维ZnO     

Controlled growth of well-aligned ZnO nanorod array using a novel solution method

A simple method of synthesizing nanomaterials and the ability to control the size and position of them are crucial for fabricating nanodevices. In this work, we developed a novel ammonia aqueous solution method for growing well-aligned ZnO nanorod arrays on a silicon substrate. For ZnO nanorod growth, a thin zinc metal seed layer was deposited on a silicon substrate by thermal evaporation. Uniform ZnO nanorods were grown on the zinc-coated silicon substrate in aqueous solution containing zinc nitrate and ammonia water. The growth temperature was as low as 60-90 degrees C and a 4-in. wafer size scale up was possible. The morphology of a zinc metal seed layer, pH, growth temperature, and concentration of zinc salt in aqueous solution were important parameters to determine growth characteristics such as average diameters and lengths of ZnO nanorods. We could demonstrate the discrete controlled growth of ZnO nanorods using sequential, tailored growth steps. By combining our novel solution method and general photolithography, we selectively grew ZnO nanorod arrays on a patterned silicon substrate. Our concepts on controlled ZnO nanorod growth using a simple solution method would be applicable for various nanodevice fabrications.     

Low-temperature growth of ZnO nanorods by chemical bath deposition

Aligned ZnO nanorod arrays were synthesized using a chemical bath deposition method at normal atmospheric pressure without any metal catalyst. A simple two-step process was developed for growing ZnO nanorods on a PET substrate at 90-95 degrees C. The ZnO seed precursor was prepared by a sol-gel reaction. ZnO nanorod arrays were fabricated on ZnO-seed-coated substrate. The ZnO seeds were indispensable for the aligned growth of ZnO nanorods. The ZnO nanorods had a length of 400-500 nm and a diameter of 25-50 nm. HR-TEM and XRD analysis confirmed that the ZnO nanorod is a single crystal with a wurtzite structure and its growth direction is [0001] (the c-axis). Photoluminescence measurements of ZnO nanorods revealed an intense ultraviolet peak at 378.3 nm (3.27 eV) at room temperature.     

Polarized surface enhanced Raman and absorbance spectra of aligned silver nanorod arrays

Polarized surface-enhanced Raman scattering (SERS) and UV-vis absorbance spectra were measured for a nonplanar Ag nanorod array substrate prepared by oblique angle vapor deposition. The anisotropy of the SERS polarization was shown to differ from that of the polarized UV-vis absorbance. The maximum SERS intensity was observed in the polarization direction perpendicular to the long axis of the Ag nanorods, while the UV-vis absorbance was strongly polarized along the direction of the long axis of the nanorod array. Analysis of the polarization data showed that molecular orientation was not the cause of the anisotropic SERS scattering. Rather, the SERS anisotropy was primarily attributed to the lateral arrangement of the three-dimensional tilted nanorod lattice in which highly localized plasmon modes are created by strong electromagnetic coupling between adjacent metallic nanorods.     

Three-Dimensional Nickel-Nickel Oxide Core-Shell Nanorod Array for Nonenzymatic Glucose Sensing

Nickel-nickel oxide core-shell nanorod array electrodes were fabricated and a preliminary application for nonenzymatic glucose determination exhibited excellent performance. The nanorod array electrode was synthesized for the first time by an anodic aluminum oxide template assisted electrochemical deposition technique. Facile oxidation was employed to convert nickel at the outer surface of the nanorods to nickel oxide, resulting in a nickel-nickel oxide core-shell nanorod array. The successful conversion was confirmed by x-ray diffraction, cyclic voltammetry, and scanning electron microscopy. The modified electrode possessed high surface area contributed by the nanorods, and efficient mass transfer due to the wide internanorod gap. The electrode provided high sensitivity (127 microampere square centimeter per millimolar), a low limit of detection (～0.5 micromolar), and a long linear dynamic range (up to 14 millimolar) for the determination of glucose. Accurate determination of glucose in human serum was performed. This synthetic strategy may have further application for the preparation of high surface area thin-film electrodes for a variety of applications.     

Formation of zinc sulfide nanorods and nanoparticles in ternary W/O microemulsions

A simple, easy approach to the synthesis of semiconductor ZnS nanorods and nanoparticles exhibiting versatile morphology-formation ability is reported. Water-insoluble zinc sulfide nanocrystals were synthesized in ternary water-in-oil (w/o) microemulsion systems stabilized by either nonionic or, in contrast, cationic surfactant. Products were visualized by transmission electron microscopy (TEM) and identified by energy-dispersive X-ray spectroscopy (EDAX); electron diffraction (ED) was also performed for individual nanorods. With varying molar ratios of water to surfactant (omega0) in solution, hence changing droplet sizes of water pool of microemulsions consequently, several morphologies with different size spans were encountered in the formation of ZnS, such as nanorods and spherical or ellipsoidal particles. Meanwhile, product morphology was also found to be sensitive to the absolute reactant concentration and concentration ratio of [Zn2+] to [S2-], the incubation time, and the ambient temperature. A schematic mechanism for the formation of ZnS nanocrystals and their morphological diversity is described. It is feasible to extend this method to the synthesis of one-dimensional nanocrystals of other semiconductors, given suitable formulae of microemulsions and other appropriate reaction conditions.     

Separation of nanorods by density gradient centrifugation

The experimental conditions necessary for the synthesis of well-defined nanoparticles are often difficult to control. There is thus a compelling need for post-synthesis separation of nanoparticles polydispersed in size and shape. We demonstrate here both theoretically and experimentally that gold nanorods with diverse aspect ratios can be separated using density gradient centrifugation. By analysing the force balance of a Brownian rod falling in a Stokes flow, we derive a rigorous and predictive model that reveals the quantitative dependency of the nanorod sedimentation rates on their mass and shape. The calculations show that while mass dependency is still the dominating factor during centrifugation, the shape factor is not insignificant. Relatively heavier but long and thin rods could sediment slower than certain size of lighter spheres, and some rods and spheres with different masses and shapes may never be separated. This mass and shape dependency is exploited to separate as-prepared gold nanorod colloids by sucrose gradient centrifugation. Two layers of nanorods with narrow aspect-ratio distributions are obtained.     

P3HT/CdS/TiO2/ZnO一维有序核壳式纳米棒阵列的构制及其在杂化太阳电池中的应用研究

采用恒电位法在铟锡氧化物导电玻璃(ITO)上制备了高度有序一维ZnO纳米棒阵列,将ZnO纳米棒阵列在TiO2溶胶中采用提拉法制备出了一维TiO2/ZnO核壳式纳米棒阵列.在一维TiO2/ZnO核壳式纳米棒阵列上电沉积CdS纳米晶得到一维CdS/TiO2/ZnO核壳式纳米棒阵列,然后在一维CdS/TiO2/ZnO核壳式纳米棒阵列上电沉积聚3-己基噻吩(P3HT)薄膜得到P3HT/CdS/TiO2/ZnO核壳式纳米结构薄膜.以该纳米结构薄膜电极为光阳极制备出新型纳米结构杂化太阳电池,研究了该类电池的光电转换性能,初步探讨了该类电池的工作机理.     

电沉积种子层化学控制生长氧化锌纳米棒和纳米管

采用水溶液法在电沉积的ZnO种子层上制备了高度取向的ZnO纳米棒阵列,并通过碱溶液化学腐蚀法获得了ZnO纳米管。对ZnO纳米棒和纳米管的溶液生长和腐蚀过程进行了分析。结果表明,种子层的结构和性能对ZnO纳米棒有着重要的影响,在-700 mV电位下沉积的种子层薄膜均匀性好,生长的纳米棒密度大、与基底垂直性好;碱溶液对纳米棒的腐蚀具有选择性,通过控制腐蚀液的浓度和时间,可获得中空的ZnO纳米管。     

Tuning the Dimensions of ZnO Nanorod Arrays for Application in Hybrid Photovoltaics

ZnO nanorod arrays are a very eligible option as electron acceptor material in hybrid solar cells, owing to their favorable electrical properties and abundance of available, easy, and low‐cost synthesis methods. To become truly effective in this field, a major prerequisite is the ability to tune the nanorod dimensions towards optimal compatibility with electron‐donating absorber materials. In this work, a water‐based seeding and growth procedure is used to synthesize ZnO nanorods. The nanorod diameter is tuned either by modifying the zinc concentration of the seeding solution or by changing the concentration of the hydrothermal growth solution. The consequences of this morphological tailoring in the performance of hybrid solar cells are investigated, which leads to a new record efficiency of 0.82 % for hydrothermally grown ZnO nanorods of size 300 nm in combination with poly(3‐hexylthiophene‐2,5‐diyl) (P3HT). This improvement is attributed to a combined effect of nanorod diameter and orientation, and possibly to a better alignment of the P3HT backbone resulting in improved charge transport.