Gd2O3:Er3+上转换发光粉在染料敏化太阳电池中的应用

采用沉淀-煅烧法制备了Gd₂O₃:Er³⁺上转换发光粉,通过X射线衍射、扫描电子显微镜、能谱和荧光光谱对其进行了表征,并利用该发光粉具有上转换发光的特性将其应用于染料敏化太阳电池(DSSC)。结果表明,管状Gd₂O₃:Er³⁺上转换发光粉可增加电池对太阳光的吸收范围和吸收效率,提高电池的光电流和光电压。研究了掺杂量对电池性能的影响,当掺杂量为5wt%时,光电转换效率从5.93%升高到7.55%,提高约27%。     

Luminescent properties of Sr<Subscript>3</Subscript>Al<Subscript>2</Subscript>O<Subscript>6</Subscript>: Eu,Pr prepared by sol–gel method

A new red-emitting long afterglow Sr₃Al₂O₆: Eu²⁺, Pr³⁺ phosphor was synthesized by sol–gel methods using Sr(NO₃)₂, Al(NO₃)₃·9H₂O, Eu(NO₃)₃ and Pr(NO₃)₃ as raw materials. The crystalline structure of the phosphor powders were characterized by X-ray diffraction. Luminescent properties of the phosphor powders were analyzed by the fluorescence spectrophotometer. Sr₃Al₂O₆: Eu²⁺, Pr³⁺ phosphor powders with single Sr₃Al₂O₆ phase were prepared at 1200 °C for 2 h in the reducing atmosphere. Pr³⁺ doped made the light intensity and the light-lasting time of Sr₃Al₂O₆: Eu²⁺, Pr³⁺ phosphors improved. The emission peaks of the Sr₃Al₂O₆: Eu²⁺, Pr³⁺ phosphor powders lay at 612 nm with the excitation of 472 nm and the longest afterglow time could last for about 15 min at Pr³⁺ content of 0.06.     

Preparation,characterization and luminescent properties of spherical CaTiO3:Pr3+ phosphors by spray pyrolysis

In this paper, spherical Pr³⁺-doped CaTiO₃ phosphor particles were fabricated through a two-step spray pyrolysis process, using citric acid and polyethylene glycol (PEG) as additives. X-ray diffraction (XRD), scanning electron microscopy (SEM), High-resolution transmission electron microscopy (HRTEM), thermogravimetric and differential thermal analysis (TG–DTA), X-ray photoelectron spectra (XPS), photoluminescence (PL), cathodoluminescence (CL) spectroscopy, and lifetime measurements were employed to characterize these samples. The results reveal that the as-prepared CaTiO₃:Pr³⁺ phosphors are spherical with submicron particle size. The particles show a strong red emission corresponding to ¹D₂–³H₄ (612 nm) of Pr³⁺ under the ultraviolet excitation (325 nm) and low voltage electron beams (1–5 kV). Furthermore, the morphology, PL and CL intensities of the CaTiO₃:Pr³⁺ phosphors can be tuned by altering the concentration of PEG, annealing temperature, and acceleration voltage. These phosphors show potential applications in the field of field emission displays (FEDs).     

Gd_2O_3∶Er~(3+)上转换发光粉在染料敏化太阳电池中的应用

采用沉淀-煅烧法制备了Gd2O3∶Er3+上转换发光粉,通过X射线衍射、扫描电子显微镜、能谱和荧光光谱对其进行了表征,并利用该发光粉具有上转换发光的特性将其应用于染料敏化太阳电池(DSSC)。结果表明,管状Gd2O3∶Er3+上转换发光粉可增加电池对太阳光的吸收范围和吸收效率,提高电池的光电流和光电压。研究了掺杂量对电池性能的影响,当掺杂量为5wt%时,光电转换效率从5.93%升高到7.55%,提高约27%。     

Morphology control and luminescence properties of BaMgAl10O17:Eu phosphors prepared by spray pyrolysis

Starting from the aqueous solutions of metal nitrates with citric acid and polyethylene glycol (PEG) as additives, BaMgAl₁₀O₁₇:Eu²⁺ (BAM:Eu²⁺) phosphors were prepared by a two-step spray pyrolysis (SP) method. X-ray powder diffraction (XRD), scanning electron microscopy (SEM) and photoluminescence spectra were used to characterize the resulted BAM:Eu²⁺ phosphors. The obtained BAM:Eu²⁺ phosphor particles have spherical shape, submicron size (0.5-3 μm). The effects of process conditions of the spray pyrolysis, such as molecular weight and concentration of PEG, on the morphology and luminescence properties of phosphor particles were investigated. Adequate amount of PEG was necessary for obtaining spherical particles, and the optimum emission intensity could be obtained when the concentration of PEG was 0.03 g/ml in the precursor solution. Moreover, the emission intensity of the phosphors increased with increasing of metal ion concentration in the solution. Compared with the BAM:Eu²⁺ phosphor prepared by citrate-gel method, spherical BAM:Eu²⁺ phosphor particles showed a higher emission intensity.     

Synthesis,Characterization and Luminescent Properties of La2Zr2O7:Eu3+ Nanorods

The Eu³⁺-doped La₂Zr₂O₇ phosphor with rod-like morphology was successfully synthesized by conventional solid state reaction and hydrothermal method. X-ray diffraction patterns, transmission electron microscopy, and photoluminescence spectra were employed to charac-terize its structure and morphology as well as luminescent properties. The results indicated that the red-emitting phosphor La₂Zr₂O₇:Eu³⁺ had well crystallized and belonged to the cubic structure with space group of Fd3m. The as-obtained product mainly appeared as straight nanorods with an average diameter of 47 nm and length of 50-700 nm. The pos-sible growth mechanism was also discussed. It was found that under blue excitation with a wavelength of 466 nm, the La₂Zr₂O₇:Eu³⁺ phosphor exhibited a characteristic red emission at 616 nm that was attributed to the hypersensitive ⁵DO_→⁷F2 _{electric dipole transition of Eu³⁺ ions. Meanwhile, it was more interesting to note that the emission of ⁵D}1_→⁷FJ _{(J=0, 1, 2) transitions and the splitting patterns of ⁵D}0_→⁷FJ _{(J=1, 2, 4) transitions of Eu³⁺ ions can be observed in the luminescent spectra of La2Zr2O7:Eu³⁺. It was demonstrated that Eu³⁺ preferred to occupy a low symmetry site.}     

Luminescent cellulose fibers activated by Eu3+-doped nanoparticles

UV- active cellulose fibers were obtained by dry-wet method spinning an 8?% by weight α-cellulose solution in N-methylomorpholine-N-oxide (NMMO) modified by europium-doped gadolinium oxyfluoride Gd₄O₃F₆:Eu³⁺ containing 5?mol (%) of the dopant. Photoluminescent nanoparticles were introduced in the in powder form into a polymer matrix during the process of cellulose dissolution in NMMO. The dependencies of emission intensity on excitation energy and the concentration of Gd₄O₃F₆:Eu³⁺ nanoparticles in the final cellulosic products were examined by photoluminescence spectroscopy (excitation and emission). The fiber structure was studied by X-ray powder diffraction analysis. The size and dispersity of the nanoparticles in the polymer matrix were evaluated using scanning electron microscopy and X-ray microanalysis. The influence of different concentration particles (in the range from 0.5 to 5?% by weight) on the mechanical properties of the fibers, such as tenacity and elongation at break, were determined.     

Photoluminescent properties of white-light-emitting Li6Y(BO3)3:Dy3+ phosphor

In this study, lithium yttrium borate (LYBO) phosphor was doped with various concentrations of trivalent dysprosium ions. To produce these phosphors, the raw materials were sintered. The phase conformation, crystallinity, grain size, and overall morphology of the synthesized phosphors were studied with X-ray diffraction and scanning electron microscopy. The optimized LYBO phosphor, i.e., the LYBO phosphor that exhibited the highest X-ray- and ultraviolet (UV)-induced photoluminescent intensities, had a Dy³⁺ concentration of 4 mol%. Photoluminescence analysis showed that this phosphor could be easily excited with near-UV light (300–400 nm). The dominant photoluminescence bands were found in the blue (480 nm) and yellow (577 nm) regions of the visible spectrum. The light yield of the X-ray-induced luminescence of the optimized Li₆Y(BO₃)₃:Dy³⁺ was found to be 66% of that of the commercially available X-ray imaging material, Gd₂O₂S:Tb³⁺ (GOS). The chromaticity coordinates of the Li₆Y(BO₃)₃:Dy³⁺ phosphor were x = 0.34 and y = 0.32, which agree well with achromatic white (x = 0.33, y = 0.33). The results of this study show that the synthesized Li₆Y(BO₃)₃:Dy³⁺ phosphor could be used as X-ray imaging material.     

Photocurable silica hybrid organic–inorganic films for photonic applications

This paper reports the detailed preparation process of Eu²⁺ activated Sr₃Al₂O₆ by a sol-gel method in the reducing atmosphere. The effect of the calcining temperature on the microstructure, crystalline particle morphology and luminescence properties of Sr₃Al₂O₆:Eu²⁺ is systematically discussed. X-ray diffraction (XRD), thermogravimetry-differential thermal analysis (TG-DTA), scanning electron microscopy (SEM) and fluorescence spectrophotometer were employed to characterize the phosphor. The Sr₃Al₂O₆:Eu²⁺ phosphor powders calcined at 1200 °C for 2 h possessed a Sr₃Al₂O₆ single cubic phase. The Sr₃Al₂O₆:Eu²⁺ crystallites showed flower-like morphology. The Sr₃Al₂O₆:Eu²⁺ phosphor powders exhibited a red broad emission band with emission peak at 612 nm under 472 nm excitation. Especially the Sr₃Al₂O₆:Eu²⁺ phosphor powders prepared at 1200 °C showed the strongest luminescence intensity, due to the pure phase and higher crystallinity of Sr₃Al₂O₆.     

Characterization and luminescence properties of Gd2O3 phosphor

Gd₂O₃ phosphor was synthesized by combustion synthesis using gadolinium nitrate hexahydrate as precursor and urea as fuel. Structural and surface morphology were studied by X-ray diffraction, transmission electron microscopy (TEM), and scanning electron microscopy (SEM). Chemical composition analysis of the phosphor was performed by Fourier-transform infrared spectroscopy, and tts optical properties were characterized by use of photoluminescence (PL) and thermoluminescence (TL) techniques. In PL spectra, feeble emission at 490 nm (blue) and intense emission at approximately 545 nm (green) are observed after excitation at 300 nm. TL measurement was performed on the Gd₂O₃ phosphor by irradiating it with γ-rays (1 kGy). A well resolved glow peak at 226.4 °C was observed. Kinetic data were estimated from the TL glow curve by use of Chen’s peak-shape method; the results are discussed in detail. The average particle size of the Gd₂O₃ phosphor was 41 nm; a monoclinic phase was formed at a firing temperature of 500 °C. This was in agreement with SEM and TEM results.     

Synthesis of Gd3PO7:Eu nanospheres via a facile combustion method and optical properties

Eu³⁺-doped Gd₃PO₇ nanospheres with an average diameter of ∼300 nm and a narrow size distribution have been prepared by a facile combustion method and structurally characterized by X-ray diffraction and field emission scanning electron microscopy. The luminescent properties were systemically studied by the measurement of excitation/emission spectra, and emission spectra under different temperatures, as well as by photostability. The strong red-emission intensity peaking at 614 nm originates the ⁵D₀→⁷F₂ transition and is observed under 254-nm irradiation, indicating that Eu³⁺ ions in Gd₃PO₇ mainly occupied non-centrosymmetry sites. The CIE1931 XY chromaticity coordinates of Gd₃PO₇:Eu³⁺ nanospheres are (x=0.654, y=0.345) in the red area, which is near the National Television Standard Committee standard chromaticity coordinates for red. Thus, Gd₃PO₇:Eu³⁺ nanospheres may be potential red-emitting phosphors for PDP and Xe-based mercury-free lamps.     

The luminescence of Pr3+ in BaY4Si5O17

The cell constants of four new monoclinic compounds BaR₄X₅O₁₇ (R = Y, Gd; X = Si, Ge) are given. The luminescence of various RE activators in the silicates is reported. Pr³⁺-activated BaY₄Si₅O₁₇ shows efficient ultraviolet 5d → 4f emission and weak 4f → 4f emission (mainly red luminescence from the ¹D₂ level). The 5d → 4f emission is ascribed to Pr³⁺ on Y sites, the 4f → 4f emission to Pr³⁺ on Ba sites. Energy transfer from Pr³⁺ to Gd³⁺ has been observed. Gd³⁺ plays an intermediate role in the energy transfer from Pr³⁺ to Sm³⁺ and to Dy³⁺ in BaGd₄Si₅O₁₇. Upon activation with Tb³⁺ the silicates show characteristic green Tb³⁺ luminescence with a quantum efficiency of 75% for ultraviolet excitation.     

The effect of different substrate temperatures on the structure and luminescence properties of Y2O3:Bi3+ thin films

Y₂O₃:Bi³⁺ phosphor thin films were prepared by pulsed laser deposition in the presence of oxygen (O₂) gas. The microstructure and photoluminescence (PL) of these films were found to be highly dependent on the substrate temperature. X-ray diffraction analysis showed that the Y₂O₃:Bi³⁺ films transformed from amorphous to cubic and monoclinic phases when the substrate temperature was increased up to 600 °C. At the higher substrate temperature of 600 °C, the cubic phase became dominant. The crystallinity of the thin films, therefore, increased with increasing substrate temperatures. Surface morphology results obtained by atomic force microscopy showed a decrease in the surface roughness with an increase in substrate temperature. The increase in the PL intensities was attributed to the crystallinity improvement and surface roughness decrease. The main PL emission peak position of the thin films prepared at substrate temperatures of 450 °C and 600 °C showed a shift to shorter wavelengths of 460 and 480 nm respectively, if compared to the main PL peak position of the powder at 495 nm. The shift was attributed to a different Bi³⁺ ion environment in the monoclinic and cubic phases.     

Luminescent core–shell Fe3O4@Gd2O3:Er3+, Li+ composite particles with enhanced optical properties

Bifunctional magneto-optical nanocomposites with Fe₃O₄ nanoparticles as a core and erbium and lithium codoped gadolinium (Gd₂O₃:Er³⁺, Li⁺) as the shell were synthesized successfully using a simple urea homogeneous precipitation method. The fabricated Fe₃O₄@Gd₂O₃:Er³⁺, Li⁺ particles were characterized by X-ray diffraction, field emission scanning electron microscopy, transmission electron microscopy, photoluminescence spectroscopy and quantum design vibrating sample magnetometry. The upconversion emission intensity was enhanced significantly comparing to that without Li⁺ ions. These bifunctional composites are expected to be potentially applied for drug delivery, cell separation and bioimaging.     

A template-free solvothermal synthesis and photoluminescence properties of multicolor Gd2O2S:xTb3+, yEu3+ hollow spheres

The multicolor Gd₂O₂S:xTb³⁺, yEu³⁺ hollow spheres were successfully synthesized via a template-free solvothermal route without the use of surfactant from commercially available Ln (NO₃)₃·6H₂O (Ln = Gd, Tb and Eu), absolute ethanol, ethanediamine and sublimed sulfur as the starting materials. The phase, structure, particle morphology and photoluminescence (PL) properties of the as-obtained products were investigated by X-ray diffraction (XRD), fourier transform infrared spectroscopy (FT-IR), field emission scanning electron microscopy (FE-SEM) and photoluminescence spectra. The influence of synthetic time on phase, structure and morphology was systematically investigated and discussed. The possible formation mechanism depending on synthetic time t for the Gd₂O₂S phase has been presented. These results demonstrate that the Gd₂O₂S hollow spheres could be obtained under optimal condition, namely solvothermal temperature T = 220 °C and synthetic time t = 16 h. The as-obtained Gd₂O₂S sample possesses hollow sphere structure, which has a typical size of about 2.5 μm in diameter and about 0.5 μm in shell thickness. PL spectroscopy reveals that the strongest emission peak for the Gd₂O₂S:xTb³⁺ and the Gd₂O₂S:yEu³⁺ samples is located at 545 nm and 628 nm, corresponding to ⁵D₄→⁷F₅ transitions of Tb³⁺ ions and ⁵D₀→⁷F₂ transitions of Eu³⁺ ions, respectively. The quenching concentration of Tb³⁺ ions and Eu³⁺ ions is 7%. In the case of Tb³⁺ and Eu³⁺ co-doped samples, when the concentration of Tb³⁺ or Eu³⁺ ions is 7%, the optimum concentration of Eu³⁺ or Tb³⁺ ions is determined to be 1%. Under 254 nm ultraviolet (UV) light excitation, the Gd₂O₂S:7%Tb³⁺, the Gd₂O₂S:7%Tb³⁺,1%Eu³⁺ and the Gd₂O₂S:7%Eu³⁺ samples give green, yellow and red light emissions, respectively. And the corresponding CIE coordinates vary from (0.3513, 0.5615), (0.4120, 0.4588) to (0.5868, 0.3023), which is also well consistent with their luminous photographs.     

Li2O-Ln2O3-SiO2:Eu3+,Bi3+体系的结构

采用ｓｏｌ－ｇｅｌ法合成了系列发光体Ｌｉ２Ｏ－Ｌｎ２Ｏ３－ＳｉＯ２：Ｅｕ＾３＾＋，Ｂｉ＾３＾＋，并确定了发光体的物相结构。当Ｌｎ＾３＾＋＝Ｙ＾３＾＋和Ｌｎ＾３＾＋＝Ｌａ＾３＾＋时，紫外光激发下Ｅｕ＾３＾＋的发射分别以红光和橙光为主，只存在一种Ｅｕ＾３＾＋发光中心；Ｌｎ＾３＾＋＝Ｇｄ＾３＾＋时，至少存在两种Ｅｕ＾３＾＋发光中心和两种Ｂｉ＾３＾＋发光中心（共掺杂Ｅｕ＾３＾＋，Ｂｉ＾３＾＋的吸收和发射所     

A novel blue-emitting phosphor LiSrPO4:Eu for white LEDs

A novel blue-emitting phosphor, LiSrPO₄:Eu²⁺, was prepared by the solid-state reaction and X-ray powder diffraction (XRD) analysis confirmed the formation of LiSrPO₄:Eu²⁺. Photoluminescence (PL) results showed that the phosphor can be efficiently excited by UV-visible light from 250 to 440 nm, and exhibited bright blue emission. The effects of the doped-Eu²⁺ concentration in LiSrPO₄:Eu²⁺ on the PL were investigated in detail. The results showed that the relative PL intensity increases with Eu²⁺-concentration increasing until a maximum intensity is reached, and then it decreases due to concentration quenching and a red-shift appears, which are explained satisfactorily with the luminescent theory. Upon excited with 396 nm light, the present synthesized phosphor has higher emission intensity than that from the commercial blue phosphor, BaMgAl₁₀O₁₇:Eu²⁺. Bright blue light-emitting diodes were fabricated by the combination of the synthesized LiSrPO₄:Eu²⁺ with ∼397 nm emitting InGaN-based chips.     

Near-infrared quantum cutting in Tb<Superscript>3+</Superscript> and Yb<Superscript>3+</Superscript>-doped Y<Subscript>2</Subscript>O<Subscript>3</Subscript> nanophosphors

Properties of the quantum-cutting phosphors are dependent on various factors such as dopant concentration, crystallinity, homogeneity, particle size and surface morphology. Effective control of the above parameters can enhance the quantum-cutting ability of the phosphor material. Nano-sized particles of Y₂O₃:Tb³⁺,Yb³⁺ were prepared with a solution-based co-precipitation method and subsequent calcination. Effective control of the reaction parameters and doping concentration helped to produce uniform nanostructures with high quantum-cutting efficiency up to 181.1 %. The energy transfer mechanism between Tb³⁺ and Yb³⁺ was studied by considering their spectroscopic properties and time-resolved spectroscopy. The high efficiency and small particle size of the quantum-cutting phosphor Y₂O₃:Tb³⁺,Yb³⁺ make it a suitable candidate for its application in solar cells.     

Enhancement of the photoluminescence and long afterglow properties of Ca<Subscript>2</Subscript>MgSi<Subscript>2</Subscript>O<Subscript>7</Subscript>:Eu<Superscript>2+</Superscript> phosphor by Dy<Superscript>3+</Superscript> co-doping

The Ca₂MgSi₂O₇:Eu²⁺ and Ca₂MgSi₂O₇:Eu²⁺, Dy³⁺ long afterglow phosphors were synthesized under a weak reducing atmosphere by the traditional high temperature solid state reaction method. The synthesized phosphors were characterized by powder X-ray diffraction (XRD) and energy dispersive X-ray spectroscopy (EDX) techniques. The luminescence properties were investigated using thermoluminescence (TL), photoluminescence (PL), long afterglow, mechanoluminescence (ML), and ML spectra techniques. The crystal structure of sintered phosphors was an akermanite type structure, which belongs to the tetragonal crystallography. TL properties of these phosphors were investigated, and the results were also compared. Under the ultraviolet excitation, the emission spectra of both prepared phosphors were composed of a broad band peaking at 535 nm, belonging to the broad emission band. When the Ca₂MgSi₂O₇:Eu²⁺ phosphor is co-doped with Dy³⁺, the PL, afterglow and ML intensity is strongly enhanced. The decay graph indicates that both the sintered phosphors contain fast decay and slow decay process. The ML intensities of Ca₂MgSi₂O₇:Eu²⁺ and Ca₂MgSi₂O₇:Eu²⁺, Dy³⁺ phosphors were proportionally increased with the increase of impact velocity, which suggests that this phosphor can be used as sensors to detect the stress of an object.     

Synthesis and photoluminescence of the Y2O3:Eu3+ phosphor nanowires in AAO template

The monodisperse array and nanowires of Y₂O₃:Eu³⁺ phosphor were synthesized using anodic aluminum oxide (AAO) template by sol–gel method. Scanning electron microscope (SEM) images indicated that Y₂O₃:Eu³⁺ nanowires are parallelly arranged, all of which are in uniform diameter of about 50 nm. The high-magnification SEM image showed that each nanowire is composed of a lot of agglutinating particles. The patterns of selected-area electron diffraction confirmed that Y₂O₃:Eu³⁺ nanowires mainly consist of polycrystalline materials. Excitation and emission spectra of Y₂O₃:Eu³⁺/AAO composite films were measured. The characteristic red emission peak of Eu³⁺ ion attributed to ⁵D₀→⁷F₂ transition in Y₂O₃:Eu³⁺/AAO nanowires broadened its halfwidth.