Modification of bamboo-based activated carbon using microwave radiation and its effects on the adsorption of methylene blue

Modification of bamboo-based activated carbon was carried out in a microwave oven under N₂ atmosphere. The virgin and modified activated carbons were characterized by means of low temperature N₂ adsorption, acid-base titration, point of zero charge (pH_pzc) measurement, FTIR and XPS spectra. A gradual decrease in the surface acidic groups was observed during the modification, while the surface basicity was enhanced to some extent, which gave rise to an increase in the pH_pzc value. The species of the functional groups and relative content of various elements and groups were given further analysis using FTIR and XPS spectra. An increase in the micropores was found at the start, and the micropores were then extended into larger ones, resulting in an increase in the pore volume and average pore size. Adsorption studies showed enhanced adsorption of methylene blue on the modified activated carbons, caused mainly by the enlargement of the micropores. Adsorption isotherm fittings revealed that Langmuir and Freundlich models were applicable for the virgin and modified activated carbons, respectively. Kinetic studies exhibited faster adsorption rate of methylene blue on the modified activated carbons, and the pseudo-second-order model fitted well for all of the activated carbons.     

Photocatalytic degradation of methylene blue in water solution by multilayer TiO2 coating on HDPE

A multilayer photocatalytic TiO₂ coating on a high-density polyethylene (HDPE) disk was found to degrade aqueous methylene blue in a batch reactor study. The TiO₂ coating was fabricated by a low-temperature method using polyurethane resin (PU) as a barrier layer for HDPE and as a binding agent for two TiO₂ layers. Adequate adhesion between the HDPE substrate and PU barrier in aqueous environment was ensured with an oxygen plasma treatment.The photocatalytic effect of immersed TiO₂ coating on the degradation of methylene blue in aqueous solution was monitored by UV–vis spectrometry as a function of UV-illumination time. Samples were allowed to adsorb methylene blue in the dark for 1 h before the UV-degradation experiments were started. The percentages of methylene blue degraded during 6 h UV illumination (λ = 365 nm) varied from 80% to 92%. The degradation followed pseudo-first order reaction kinetics, and the observed rate constants (k_obs) were between 0.27 and 0.43 h⁻¹.     

Optimization of the ultrasonic assisted removal of methylene blue by gold nanoparticles loaded on activated carbon using experimental design methodology

The present study was focused on the removal of methylene blue (MB) from aqueous solution by ultrasound-assisted adsorption onto the gold nanoparticles loaded on activated carbon (Au-NP-AC). This nanomaterial was characterized using different techniques such as SEM, XRD, and BET. The effects of variables such as pH, initial dye concentration, adsorbent dosage (g), temperature and sonication time (min) on MB removal were studied and using central composite design (CCD) and the optimum experimental conditions were found with desirability function (DF) combined response surface methodology (RSM). Fitting the experimental equilibrium data to various isotherm models such as Langmuir, Freundlich, Tempkin and Dubinin–Radushkevich models show the suitability and applicability of the Langmuir model. Analysis of experimental adsorption data to various kinetic models such as pseudo-first and second order, Elovich and intraparticle diffusion models show the applicability of the second-order equation model. The small amount of proposed adsorbent (0.01 g) is applicable for successful removal of MB (RE > 95%) in short time (1.6 min) with high adsorption capacity (104–185 mg g⁻¹).     

Effect of electrostatic interaction on the methylene blue and methyl orange adsorption by the pristine and functionalized carbon nanotubes

Multi-walled carbon nanotubes (MWCNTs) were functionalized with cysteamine groups by several percentage of mass as adsorbents, then kinetics adsorption capacity was investigated for methylene blue (MB) and methyl orange (MO) as anionic and cationic dyes adsorbate molecules, respectively. The effect of temperature (from 283 to 303 K), contact time and initial concentration of the MB and MO dyes in a solution (10 to 40 ppm) was considered. The optimal contact time was found to be about 60 min. Some kinetics model such as pseudo-first-order, pseudo-second-order, intra-particle diffusion and the Elovich were tested. The adsorptions of MB dye on the pristine and functionalized MWCNT surfaces were found to be the intra-particle diffusion and the pseudo-second-order kinetic model, respectively and for adsorption of MO dye by the pristine and low functionalized MWCNTs and highly functionalized tubes, found to be the pseudo-second-order and intra-particle diffusion kinetic model, respectively, based on the chi-square statistic (X²) and also high correlation coefficient (R²) values.     

Efficient removal of crystal violet and methylene blue from wastewater by ultrasound nanoparticles Cu-MOF in comparison with mechanosynthesis method

The present investigation reports the synthesis of CuBTC (BTC = 1,3,5-benzenetricarboxylate) metal–organic frameworks (MOFs) under solid-state conditions and ultrasound irradiation. Herein, we study uptake and release properties of crystal violet (CV) and methylene blue (MB) from ultrasound nano-CuBTC MOF in comparison with mechanosynthesis method (bulk structure). The ultrasound-assisted methods give a decrease in the surface area as calculated from the reduced nitrogen adsorption capability. In comparison, the uptake of guest molecules on ultrasound nano-CuBTC is remarkable and clearly exceeds that of bulk structure in the aqueous solution of guests. In bulk compound the channel length is increased so that the amount of adsorption is decreased a little. The small guest enters and leaves the cavity rapidly, whereas larger guests enter slowly due to their size relative to the size of the gaps in the capsule. As a result, the uptake and release of MB from CuBTC is faster than that of CV.     

Effects of NiTiO3 nanoparticles supported by mesoporous MCM-41 on photoreduction of methylene blue under UV and visible light irradiation

In this work, we report the synthesis of nickel titanate nanoparticles loaded on nanomesoporous MCM-41 nanoparticles to determine the effect of MCM-41 nanoparticles on the photocatalytic activities of nickel titanate (NiTiO₃) nanoparticles by using simple solid-state dispersion (SSD) method. Fourier transform infrared spectroscopy (FT-IR), X-ray powder diffraction (XRD), transmission electron microscopy (TEM) and UV–Vis diffuse reflectance spectra (DRS) analysis were used to characterize the size and morphology of the obtained nanocomposite. The photocatalytic activity (PA) of the as-prepared NiTiO₃ loaded on MCM-41 was evaluated by degradation of the methylene blue under irradiation of UV and visible light. The results showed that NiTiO₃ loaded on nanosize MCM-41 has higher photocatalytic activity than that of NiTiO₃ nanoparticles.     

超高比表面积碳气凝胶常压干燥制备与结构分析

以间苯二酚(R)-甲醛(F)为原料,加入表面活性剂P123以增强材料的骨架强度的方法,采用常压干燥技术制备了RF碳气凝胶,并进行了二氧化碳活化以调节其孔结构。扫描电子显微镜(SEM)测试表明,常压干燥的碳气凝胶结构中具有更大的纳米颗粒,骨架结构变粗,活化使碳气凝胶骨架结构更加致密;红外吸收光谱(FTIR)表明,表面活性剂P123中的醚键与RF苯环中的羟基存在强的相互作用,碳化后P123特征峰消失;热重曲线(TG和DTG)分析说明P123在440 ℃左右分解完全,不会对碳气凝胶的成分产生影响,并能起到良好的造孔作用;氮气吸附表明常压干燥制备的碳气凝胶比表面积约为570 m2/g,活化之后的比表面积高达3 500 m2/g左右。     

超高比表面积碳气凝胶常压干燥制备与结构分析

以间苯二酚(R)-甲醛(F)为原料,加入表面活性剂P123以增强材料的骨架强度的方法,采用常压干燥技术制备了RF碳气凝胶,并进行了二氧化碳活化以调节其孔结构。扫描电子显微镜(SEM)测试表明,常压干燥的碳气凝胶结构中具有更大的纳米颗粒,骨架结构变粗,活化使碳气凝胶骨架结构更加致密;红外吸收光谱(FTIR)表明,表面活性剂P123中的醚键与RF苯环中的羟基存在强的相互作用,碳化后P123特征峰消失;热重曲线(TG和DTG)分析说明P123在440 ℃左右分解完全,不会对碳气凝胶的成分产生影响,并能起到良好的造孔作用;氮气吸附表明常压干燥制备的碳气凝胶比表面积约为570 m2/g,活化之后的比表面积高达3 500 m2/g左右。     

Study of the mobility,surface area,and sintering behavior of agglomerates in the transition regime by tandem differential mobility analysis

The surface area of nanosized agglomerates is of great importance as the reactivity and health effects of such particles are highly dependent on surface area. Changes in surface area through sintering during nanoparticle synthesis processes are also of interest for precision control of synthesised particles. Unfortunately, information on particle surface area and surface area dynamics is not readily obtainable through traditional particle mobility sizing techniques. In this study, we have experimentally determined the mobility diameter of transition regime agglomerates with 3, 4, and 5 primary particles. Agglomerates were produced by spray drying well-characterised polystyrene latex particles with diameters of 55, 67, 76, and 99 nm. Tandem differential mobility analysis was used to determine agglomerate mobility diameter by selecting monodisperse agglomerates with the same number of primary particles in the first DMA, and subsequently completely sintering the agglomerates in a furnace aerosol reactor. The size distribution of the completely sintered particles was measured by an SMPS system, which allowed for the determination of the number of primary particles in the agglomerates. A simple power law regression was used to express mobility diameter as a function of primary particle size and the number of primary particles, and had an excellent correlation (R² = 0.9971) with the experimental data. A scaling exponent was determined from the experimental data to relate measured mobility diameter to surface area for agglomerates. Using this relationship, the sintering characteristics of agglomerates were also examined for varying furnace temperatures and residence times. The sintering data agreed well with the geometric sintering model (GSM) model proposed by Cho & Biswas (2006a) as well as with the model proposed Koch & Friedlander (1990) for sintering by viscous flow.