Comparison of the coating properties and corrosion rates in electroless Ni-P/PTFE composites prepared by different types of surfactants

The effects of the addition of three types of surfactants (cationic, anionic, non-ionic) at different concentrations in the plating bath on the deposition rate, PTFE content and surface morphology of electroless Ni-P/PTFE composite coatings were investigated. It was demonstrated that the cationic and non-ionic surfactants created a uniform distribution of PTFE particles in the coatings. The effects of the surfactant type and concentration on the corrosion properties of Ni-P/PTFE coatings were also studied. The corrosion resistance was increased by the incorporation of PTFE particles into the Ni-P matrix. The level of improvement depended largely on the type and concentration of the applied surfactants.     

The effect of carbon nanotubes on the corrosion and tribological behavior of electroless Ni-P-CNT composite coating

In this study, Ni-P-CNT composite coating was successfully deposited on the surface of copper by electroless plating. X-ray diffraction (XRD) analysis and scanning electron microscopy (SEM) were used to characterize the coatings. The wear behavior of the coatings was investigated using a pin-on-disk test rig and subsequently friction coefficient data were reported. The corrosion behavior of the Ni-P and Ni-P-CNT coated specimen were evaluated through polarization curves and electrochemical impedance spectroscopy (EIS) in 3.5 wt.% NaCl aqueous solution at the room temperature. The results indicated that the incorporation of carbon nanotubes (CNTs) in the coating improved both tribological behavior and corrosion resistance. These improvements have been attributed to superior mechanical properties, unique topological structure and high chemical stability of nanotubes.     

Development and evaluation of electroless Ag-PTFE composite coatings with anti-microbial and anti-corrosion properties

Electroless Ag-polytetrafluoroethylene (PTFE) composite coatings were prepared on stainless steel sheets. The existence and distribution of PTFE in the coatings were analysed with an energy dispersive X-ray microanalysis (EDX). The contact angle values and surface energies of the Ag-PTFE coatings, silver coating, stainless steel, titanium and E. coli Rosetta were measured. The experimental results showed that stainless steel surfaces coated with Ag-PTFE reduced E. coli attachment by 94-98%, compared with silver coating, stainless steel or titanium surfaces. The anti-bacterial mechanism of the Ag-PTFE composite coatings was explained with the extended Derjaguin-Landau-Verwey-Overbeek (DLVO) theory. The anticorrosion properties of the Ag-PTFE composite coatings in 0.9% NaCl solution were studied. The results showed that the corrosion resistance of the Ag-PTFE composite coatings was superior to that of stainless steel 316L.     

Effect of pulsed laser parameters on in-situ TiC synthesis in laser surface treatment

Commercial titanium sheets pre-coated with 300-μm thick graphite layer were treated by employing a pulsed Nd:YAG laser in order to enhance surface properties such as wear and erosion resistance. Laser in-situ alloying method produced a composite layer by melting the titanium substrate and dissolution of graphite in the melt pool. Correlations between pulsed laser parameters, microstructure and microhardness of the synthesized composite coatings were investigated. Effects of pulse duration and overlapping factor on the microstructure and hardness of the alloyed layer were deduced from Vickers micro-indentation tests, XRD, SEM and metallographic analyses of cross sections of the generated layer. Results show that the composite cladding layer was constituted with TiC intermetallic phase between the titanium matrix in particle and dendrite forms. The dendritic morphology of composite layer was changed to cellular grain structure by increasing laser pulse duration and irradiated energy. High values of the measured hardness indicate that deposited titanium carbide increases in the conditions with more pulse duration and low process speed. This occurs due to more dissolution of carbon into liquid Ti by heat input increasing and positive influence of the Marangoni flow in the melted zone.     

Corrosion behavior and composition analysis of chromate passive film on electroless Ni-P coating

A passive film was formed on electroless Ni-P coating (ENPC) in a bath of K₂Cr₂O₇ 30 g/l. XPS and electrochemical methods were employed to analyze its chemical compositions and corrosion behaviors. The potentiodynamic polarization tests indicated the corrosion current of the passivated sample was 1/30 that of as-plated ENPC. The XPS analysis illustrated the film comprised Cr, Ni and O. The film thickness was evaluated to be a few nanometers according to the sputtering rate of Ar⁺ ion. High-resolution XPS spectra suggested that the detected Cr in film was in the form of trivalent compounds, Cr₂O₃ and Cr(OH)₃.     

Preparation of ceramic coating on Ti substrate by Plasma electrolytic oxidation in different electrolytes and evaluation of its corrosion resistance

Ceramic oxide coatings (titania) were produced on Ti by micro-arc oxidation in different aluminate and carbonate based electrolytes. This process was conducted under constant pulsed DC voltage condition. The effect of KOH and NaF in aluminate based solution was also studied. The surface morphology, growth and phase composition of coatings were investigated using scanning electron microscope and X-ray diffraction. Corrosion behavior of the coatings was also examined by potentiodynamic polarization and electrochemical impedance spectroscopy. It was found that the sparking initiation voltage (spark voltage) had a significant effect on the form and properties of coatings. Coatings obtained from potassium aluminate based solution had a lower spark voltage, higher surface homogeneity and a better corrosion resistance than the carbonate based solution. Addition of NaF instead of KOH had improper effects on the homogeneity and adhesion of coatings which in turn caused a poor corrosion protection behavior of the oxide layer. AC impedance curves showed two time constants which is an indication of the coatings with an outer porous layer and an inner compact layer.     

Friction and wear properties of the co-deposited Ni-SiC nanocomposite coating

Ni-SiC nanocomposite coatings were produced by electrodeposition from a nickel sulfate bath containing SiC nanoparticles with an average particle size of 30 nm. The characteristics of the coatings were assessed by scanning electron microscopy and microhardness test. The friction and wear performance of Ni-SiC nanocomposite coatings and Ni film were comparatively investigated sliding against Si₃N₄ ceramic balls under non-lubricated conditions. The results indicated that compared to Ni film, Ni-SiC nanocomposite coating exhibited enhanced microhardness and wear resistance. The effect of SiC nanoparticles on the friction and wear resistance is discussed in detail.     

Electroless deposition of Ni-W-P coating on AZ91D magnesium alloy

Ternary Ni-W-P alloy coating was deposited directly on AZ91D magnesium alloy by using an alkaline-citrate-based baths. Nickel sulfate and sodium tungstate were used as metal ion sources, respectively, and sodium hypophosphite was used as a reducing agent. The pH value of the electroless bath was tailored for magnesium alloy. The coating was characterized for its structure, morphology, microhardness and the corrosion properties. SEM observation showed the presence of dense and coarse nodules in the ternary coating. EDS analysis showed that the content of tungsten in the Ni-W-P alloy was 4.5 wt.%. Both the electrochemical analysis and the immersion test in 10% HCl solution revealed that the ternary Ni-W-P coating exhibited good corrosion resistance properties in protecting the AZ91D magnesium alloy.     

Studies on the influence of surface pre-treatments on electroless copper coating of boron carbide particles

Boron carbide is one of the hard ceramic particles which find application as structural materials and neutron shielding material due to its high neutron capture cross section. Copper coating on boron carbide particle is essential for the synthesis of metal-ceramic composites with enhanced sinterability and dispersibility. Surface characteristics of the substrate and the coating parameters play a foremost role in the formation of effective electroless coating. The effect of surface pre-treatment conditions and pH on electroless copper coating of boron carbide particles has been studied. Surface pre-treatement of B₄C when compared to acid treated and alkali treated particles were carried out. Uniform copper coating was observed at pH 12 in alkali treated particles when compared to others due to the effective removal of inevitable impurities during the production and processing of commercially available B₄C. A threshold pH 11 was required for initiation of copper coating on boron carbide particles. The growth pattern of the copper coating also varies depending on the surface conditions from acicular to spherical morphology.     

A method to select the optimal equivalent electrical circuit applied to study corrosion system of composite coating on magnesium alloy

Mg-Al layered double hydroxides/micro-arc oxidation (Mg-Al LDHs/MAO) composite coating on AZ31 magnesium alloy is fabricated by hydrothermal treatment. Corrosion system is described by ideal equivalent circuit, in which each layer or interface is regarded as the corresponding electronic component. The optimal equivalent circuit is determined by the minimum total error area of electrical parameters. Error areas of phase angle and modulus for experimental and fitting data are calculated for the selected four different kinds of circuit models such as EC1, EC2, EC3 and EC4. The results show that circuit model EC2 is the best because its total error is 1/2, 2/19 and 1/15 of error values for other three kinds of circuit models, respectively. This work reveals that the optimal equivalent electrical circuit can well reflect corrosion system of Mg-Al LDHs/MAO composite coating with the help of electrochemical impedance spectroscopy (EIS) and scanning electron microscope (SEM).     

Electroless Ni-P coating preparation of conductive mica powder by a modified activation process

A modified activation process was developed for electroless Ni-P coating preparation of conductive mica powder. The electroless Ni-P coating process was modified by replacing the conventional sensitization and activation steps only using activation step with a Pd(II)-APTHS activator, which is a complex of Pd(II) ion with a derivate γ-aminopropyltrihydroxysilane (APTHS) from the hydrolysis of γ-aminopropyltriethoxysilane (APTES). The activated reaction progress and resulted Ni-P coating were characterized by XPS, SEM/EDX and TEM. Electroless nickel deposition was successfully initiated by this activation process. This activation process is very simple, and the obtained Ni-P deposits have the advantages of uniformity, continuity and densification. The average specific resistivity for the Ni-P coated mica powder was 4.85 × 10⁻² Ω cm.     

Electroless Ni-P/Ni-B duplex coatings for improving the hardness and the corrosion resistance of AZ91D magnesium alloy

The Ni-P/Ni-B duplex coatings were deposited on AZ91D magnesium alloy by electroless plating process and their structure, morphology, microhardness and corrosion resistance were evaluated. The duplex coatings were prepared using dual baths (acidic hypophosphite- and alkaline borohydride-reduced electroless nickel baths) with Ni-P as the inner layer. The coatings were amorphous in as-plated condition and crystallized and produced nickel borides upon heat-treatment. SEM observations showed that the duplex interface on the magnesium alloy was uniform and the compatibility between the layers was good. The Ni-P/Ni-B coatings microhardness and corrosion resistance of having Ni-B coating as the outer layer was higher than Ni-P coatings. The Ni-P/Ni-B duplex coatings on AZ91D magnesium alloy with high hardness and good corrosion resistance properties would expand their scope of applications.     

The rate of electroless deposition of a four-component Ni-W-P-ZrO2 composite coating from a glycine bath

Four-component Ni-W-P-ZrO₂ composite coatings were electroless deposited. A bath containing aminoacetic acid as the agent complexing nickel ions, and sodium tungstate(VI) as the source of tungstate was used. It has been determined that as the bath's pH increases (from 5 to 6) so does the rate of coating deposition while the phosphorus content in the coating decreases. Both an increase in the aminoacetic acid concentration and an increase in the sodium tungstate cause a reduction in the rate of deposition of the Ni-W-P-ZrO₂ coating. Changes in the concentration of the two components in the bath result in a change in the composition of the coatings. When the concentration of the components is too high the bath loses its stability and a sediment precipitates itself. The ZrO₂ content in the coating depends most on the amount of this powder in the suspension.     

Preparation of ceramic coating on Ti substrate by plasma electrolytic oxidation in different electrolytes and evaluation of its corrosion resistance: Part II

The aim of this work is to discuss the growth characteristics and corrosion behavior of the prepared ceramic coatings on titanium by plasma electrolytic oxidation (PEO) technique in different electrolytes. PEO process was carried out on titanium under constant voltage regime using a pulse power supply. Three kinds of electrolytes, phosphate, silicate and borate based solutions, were used to evaluate the influence of electrolyte composition on the structure, surface morphology, phase composition and corrosion behavior of prepared ceramic oxide films (titania). The phase composition of the coatings was investigated by X-ray diffraction. Scanning electron microscopy was employed to evaluate the growth and surface morphology of coatings. Elements of coatings were investigated with energy dispersive spectrometer. Corrosion behavior of the coatings was also examined by potentiodynamic polarization and electrochemical impedance spectroscopy. The spark voltage of oxide films had a significant effect on the surface morphology, size and homogeneity of micro-pores, thickness and corrosion properties of coatings.     

Preparation and properties of titanium oxide film on NiTi alloy by micro-arc oxidation

Titanium oxide ceramic coatings were prepared by micro-arc oxidation (MAO) in galvanostatic regime on biomedical NiTi alloy in H₃PO₄ electrolyte using DC power supply. The surface of the coating exhibited a typical MAO porous and rough structure. The XPS analysis indicated that the coatings were mainly consisted of O, Ti, P, and a little amount of Ni, and the concentration of Ni was greatly reduced compared to that of the NiTi substrate. The TF-XRD analysis revealed that MAO coating was composed of amorphous titanium oxide. The coatings were tightly adhesive to the substrates with the bonding strength more than 45 MPa, which was suitable for medical applications. The curves of potentiodynamic porlarization indicated that the corrosion resistance of NiTi alloy was significantly improved due to titanium oxide formation on NiTi alloy by MAO.     

Electrodeposition of high corrosion resistance Cu/Ni-P coating on AZ91D magnesium alloy

High corrosion resistance Cu/Ni-P coatings were electrodeposited on AZ91D magnesium alloy via suitable pretreatments, such as one-step acid pickling-activation, once zinc immersion and environment-friendly electroplated copper as the protective under-layer, which made Ni-P deposit on AZ91D Mg alloy in acid plating baths successfully. The pH value and current density for Ni-P electrodeposition were optimized to obtain high corrosion resistance. With increasing the phosphorous content of the Ni-P coatings, the deposits were found to gradually transform to amorphous structure and the corrosion resistance increased synchronously. The anticorrosion ability of AZ91D Mg alloy was greatly improved by the amorphous Ni-P deposits, which was investigated by potentiodynamic polarization curve and electrochemical impedance spectroscopy (EIS). The corrosion current density (I_corr) of the coated Mg alloy substrate is about two orders of magnitude less than that of the uncoated.     

Preparation and properties of super-hydrophobic coating on magnesium alloy

The super-hydrophobic coating was successfully fabricated on the surface of magnesium alloy AZ31 by chemical etching and surface modification. The surface morphologies, compositions, wettability and corrosion resistance of the coating were investigated with SEM, XPS, contact angle measurement and electrochemical method, respectively. It shows that the rough and porous micro-nano-structure was presented on the surface of magnesium alloy, and the contact angle could reach up to 157.3 ± 0.5° with sliding angle smaller than 10°. The super-hydrophobic coating showed a long service life. The results of electrochemical measurements showed that anticorrosion property of magnesium alloy was improved. The super-hydrophobic phenomenon of the prepared surface was analyzed with Cassie theory, and it finds that only about 10% of the water surface is contacted with the metal substrate and the rest 90% is contacted with the air cushion.     

Preparation and properties of electroless Ni-P-SiO2 composite coatings

Dispersible SiO₂ nanoparticles were co-deposited with electroless Ni-P coating onto AISI-1045 steel substrates in the absence of any surfactants in plating bath. The resulting Ni-P/nano-SiO₂ composite coatings were heat-treated for 1 h at 200 °C, 400 °C, and 600 °C, respectively. The hardness and wear resistance of the heat-treated composite coatings were measured. Moreover, the structural changes of the composite coatings before and after heat treatment were investigated by means of X-ray diffraction (XRD), while their elemental composition and morphology were analyzed using an energy dispersive spectrometer (EDS) and a scanning electron microscope (SEM). Results show that co-deposited SiO₂ particles contributed to increase the hardness and wear resistance of electroless Ni-P coating, and the composite coating heat-treated at about 400 °C had the maximum hardness and wear resistance.     

Novel strategy in increasing stability and corrosion resistance for super-hydrophobic coating on aluminum alloy surfaces

A novel super-hydrophobic coating was prepared by chemical modification on the anodized aluminum alloy surface. The surface structure was characterized by water contact angle measurement, scanning electron microscopy (SEM), and the composition was measured by X-ray photoelectron spectroscopy (XPS). The corrosion behavior of the super-hydrophobic coating was evaluated by the polarization curve and the electrochemical impedance spectroscopy (EIS). It was found that the static water contact angle on the surface of super-hydrophobic coating was as high as 167.7 ± 1.2°, and the sliding angle was 5°. The super-hydrophobic coating resulted in excellent corrosion resistance property and the super-hydrophobic coating showed a good stability.     

Facile synthesis and electrochemical properties of a novel Ni-B/TiC composite coating via ultrasonic-assisted electrodeposition

A novel Ni-B/TiC composite coating was synthesized by ultrasonic-assisted direct current electrodeposition. Ultrasonic technology was adopted to prevent the agglomeration of nanoparticle, improve the structure and corrosion resistance, using an ultrasonic bath at frequency 40 KHz and acoustic power 300 W. The influences of current density and deposition time on its structure and electrochemical behaviors were studied. Under ultrasonic dispersion, the composite coatings are smooth, compact with protrusion structure sparsely distributed on it. The average roughness (S_a) was about 13.6–26.1 nm. The crystallite size is 10–21 nm. The preferred orientation is Ni (1 1 1) texture. EIS results indicated that the corrosion resistance was greatly improved by ultrasonic-assisted method. The corrosion mechanism is consistent with one-time constant EEC model of R_s(CPE_dlR_ct). With the increase of immersion time, the R_ct of the composite coating often first increased and then decreased. Under ultrasonic, current density 2 A dm⁻² and deposition time 20 min were the appropriate parameters for the optimal corrosion resistance and excellent long-term electrochemical stability in 3.5 wt% NaCl corrosive solution. This coating shows good application prospect for corrosion protection in aggressive environment.