Raman spectroscopic investigation of acetylation of raw cotton

Raman spectroscopy has been used to investigate raw cotton acetylation using acetic anhydride/4-dimethylaminopyridine (DMAP) catalyst blend without solvent. The Raman data further confirm successful acetylation as shown by FTIR that was demonstrated previously to be highly sensitive for determining the level of acetylation. However, the Raman peaks are much weaker than the FTIR bands. Nevertheless, the variations of the extent of acetylation estimated from both Raman and FTIR spectra with weight percent gain due to acetylation (WPG) were observed to follow the same pattern. The degrees of acetylation calculated from Raman data were also found to increase linearly with that calculated from the more sensitive FTIR technique. Raman technique is thus suitable for further development as an analytical tool for determining the acetylation level of natural cellulose fibres. Raman data have also shown that the acetylation reaction reduces the crystallinity of cotton.     

Infrared and 13C MAS nuclear magnetic resonance spectroscopic study of acetylation of cotton

The acetylation of commercial cotton samples with acetic anhydride without solvents in the presence of about 5% 4-dimethylaminopyridine (DMAP) catalyst was followed using Fourier transform infrared (FTIR) and 13C MAS NMR spectroscopy. This preliminary investigation was conducted in an effort to develop hydrophobic, biodegradable, cellulosic materials for subsequent application in oil spill cleanup. The FTIR results provide clear evidence for successful acetylation though the NMR results indicate that the level of acetylation is low. Nevertheless, the overall results indicate that cotton fibres are potential candidates suitable for further development via acetylation into hydrophobic sorbent materials for subsequent oil spill cleanup application. The results also indicate that de-acetylation, the reverse of the equilibrium acetylation reaction, occurred when the acetylation reaction was prolonged beyond 3 h.     

松木屑在AmimCl离子液体中的原位均相乙酰化

不使用任何催化剂, 在离子液体1-烯丙基-3-甲基咪唑氯盐(AmimCl)中实现了松木屑的一步均相乙酰化, 乙酰化松木的质量增重(WPG)范围在-89％～156％之间. 研究表明, 在均相条件下, 可以通过控制乙酰化时间, 乙酰化温度及乙酸酐/OH的摩尔比来控制乙酰化松木的WPG值. 用FTIR, 13C NMR, TGA 和 SEM对乙酰化松木进行表征. 结果表明, 13C NMR和FTIR谱图有明显的乙酰基特征峰, 且乙酰化松木的结构均匀致密, 其热稳定性高达205 ℃, 略低于原生松木.     

侧链含炔丙基的PLGA-PEG-PLGA三嵌段共聚物的合成与表征

通过简单易行的技术路线合成了炔丙基化乙交酯单体,以1,4-二甲氨基吡啶为催化剂,亲水性和生物相容性良好的聚乙二醇为大分子引发剂,在较滥条件下引发炔丙基化乙交酯和丙交酯的开环共聚,制备了侧链含炔丙基的聚(乳酸-羟基乙酸)-聚乙二醇-聚(乳酸-羟基乙酸)(PLGA-PEG-PLGA)三嵌段共聚物,并对产物的组成与结构进行了表征.为生物孤犊触乳聚酯的分子修饰、生物相容性的提高探索一条简单而有效的途径     

The behavior of hydroxyl units of synthetic goethite and its dehydroxylated product hematite.

The behavior of the hydroxyl units of synthetic goethite and its dehydroxylated product hematite was characterized using a combination of Fourier transform infrared (FTIR) spectroscopy and X-ray diffraction (XRD) during the thermal transformation over a temperature range of 180-270 degrees C. Hematite was detected at temperatures above 200 degrees C by XRD while goethite was not observed above 230 degrees C. Five intense OH vibrations at 3212-3194, 1687-1674, 1643-1640, 888-884 and 800-798 cm(-1), and a H2O vibration at 3450-3445 cm(-1) were observed for goethite. The intensity of hydroxyl stretching and bending vibrations decreased with the extent of dehydroxylation of goethite. Infrared absorption bands clearly show the phase transformation between goethite and hematite: in particular. the migration of excess hydroxyl units from goethite to hematite. Two bands at 536-533 and 454-452 cm(-1) are the low wavenumber vibrations of Fe-O in the hematite structure. Band component analysis data of FTIR spectra support the fact that the hydroxyl units mainly affect the a plane in goethite and the equivalent c plane in hematite.     

原位ATR-FTIR法研究丁二烯配位聚合反应动力学

将原位全反射傅立叶红外光谱(in situATR-FTIR)技术应用于研究稀土催化丁二烯配位聚合反应过程,探讨了采集FTIR谱图的背景、用于定量计算的特征峰的选择与确定、单体浓度和所确定的特征峰强度的关系及丁二烯溶液聚合反应动力学.在聚合过程中不同时间取样得到聚合物样品,采用GPC、FTIR、POM和DSC分别对这些样品进行分子量及其分布、微观结构及其含量、玻璃化温度及结晶特性的分析与表征.结果表明,选用溶剂正己烷为背景,采集的FTIR谱图(600~1800 cm-1)中仅出现丁二烯的3个特征峰1592、1010和904 cm-1,且基线更为平滑,计算误差小.在丁二烯浓度为0.46~3.88 mol.L-1的范围内,丁二烯的这3个特征峰的强度均与丁二烯浓度成正比,其中904 cm-1处的特征峰强,可选作定量计算的特征峰.聚合反应速率对单体浓度呈现一级动力学关系,表观增长活化能为56.5 kJ.moL-1.聚丁二烯产物的分子量随单体转化率呈线性增加,其GPC谱图表明所得聚合物的分子量呈单峰分布,分布指数(Mw/Mn)在2.5左右.聚丁二烯产物中顺-1,4结构含量大于98%,其玻璃化转变温度约为-109℃,可产生较明显的结晶现象.     

New transesterification reaction between acetylated wood and tetramethoxysilane: A feasibility study

Novel transesterification of acetylated maritime pine sapwood (Pinus pinaster Soland) reaction was performed with tetramethoxysilane (TMOS) in presence of dibutyltin oxide as a catalyst. Transesterification was confirmed by weight percent gain calculations (WPG), infrared spectroscopy (FTIR) as well as ¹³C and ²⁹Si NMR CP-MAS analysis. The results showed that transesterification indeed occurs via exchange of acetate groups from acetylated wood and methoxysilane groups from TMOS. The effect of temperatures and reaction time upon transesterification efficiency was also investigated.     

Fourier transform infrared study of the effect of diabetes on rat liver and heart tissues in the CH region

Diabetes mellitus is characterized by hyperglycemia, a relative lack of insulin. The metabolic disturbances in diabetic patients are often associated with cardiac and liver dysfunctions. Generally, experimental diabetic models in animals have been used to study diabetes-related changes in organ function, but the complexity of intact tissues can cause contradictory results. For this reason, different techniques have been used to understand the mechanisms of these dysfunctions in diabetic organs. The purpose of the present study is to investigate the effects of streptozotocin (STZ)-induced diabetes on rat liver and heart tissues at the molecular level by Fourier Transform Infrared (FTIR) spectroscopy. Wistar rats of both sexes, weighing 200-250 g, were made diabetic by a single injection of 50 mg kg(-1) intraperitoneal (i.p.) streptozotocin dissolved in 0.05 M citrate buffer (pH 4.5) and they were kept for 4-5 weeks. The diabetes status was checked by measuring the blood glucose level. In the complex FTIR spectra, the bands in the CH region for example the CH(2) antisymmetric and symmetric stretching, the CH(3) symmetric and asymmetric stretching vibrations due to lipids and proteins in the 3000-2800 cm(-1) region and CH(2) scissoring around 1464 cm(-1) and the CH(3) scissoring at 1454 cm(-1) were analyzed. Characteristic spectral bands of these diabetic samples were compared with those of control group to confirm the effect of diabetes on liver and heart tissues. The FTIR spectra revealed dramatic differences in the band positions and bandwidths, signal intensity values and signal intensity ratios between diabetic and control tissues. Similar differences were observed for diabetic liver and heart tissues. A significant increase in the bandwidth of the CH(2) symmetric and antisymmetric stretching and the CH(3) symmetric and asymmetric stretching bands has been observed for both tissue types. The wavenumber of the CH(3) asymmetric stretching band shifts to lower values, indicating an increase in the order in the deep interior part of the lipid chains. The ratio of the CH(2) symmetric to CH(3) symmetric stretching band (lipid/protein ratio) decreases by 13% for diabetic heart and liver tissues. A decrease is also detected in the ratio of the CH(2) scissoring to the CH(3) scissoring mode. The overall intensity of these bands is seen to increase for diabetic tissues.     

The DMAP-catalyzed acetylation of alcohols--a mechanistic study (DMAP = 4-(dimethylamino)pyridine)

The acetylation of tert-butanol with acetic anhydride catalyzed by 4-(dimethylamino)pyridine (DMAP) has been studied at the Becke3 LYP/6-311 + G(d,p)//Becke3 LYP/6-31G(d) level of theory. Solvent effects have been estimated through single-point calculations with the PCM/UAHF solvation model. The energetically most favorable pathway proceeds through nucleophilic attack of DMAP at the anhydride carbonyl group and subsequent formation of the corresponding acetylpyridinium/acetate ion pair. Reaction of this ion pair with the alcohol substrate yields the final product, tert-butylacetate. The competing base-catalyzed reaction pathway can either proceed in a concerted or in a stepwise manner. In both cases the reaction barrier far exceeds that of the nucleophilic catalysis mechanism. The reaction mechanism has also been studied experimentally in dichloromethane through analysis of the reaction kinetics for the acetylation of cyclohexanol with acetic anhydride, in the presence of DMAP as catalyst and triethylamine as the auxiliary base. The reaction is found to be first-order with respect to acetic anhydride, cyclohexanol, and DMAP, and zero-order with respect to triethyl amine. Both the theoretical as well as the experimental studies strongly support the nucleophilic catalysis pathway.     

18-membered cyclic esters derived from glycolide and lactide: preparations, structures and coordination to sodium ions

From reactions between glycolide or lactide (4 equiv.) with 4-dimethylaminopyridine, DMAP (1 equiv.) and NaBPh(4) (1 equiv.) in benzene at 70 degrees C the cyclic ester adducts (CH(2)C(O)O)(6)NaBPh(4) and (CHMeC(O)O)(6)NaBPh(4) are formed respectively. The structures of the salts Na[(S,R,S,R,S,R)-(CH(3)CHC(O)O)(6)](2)BPh(4).CH(3)CN and (CH(2)C(O)O)(6)NaBPh(4).(CH(3)CN)(2) are reported. The cyclic esters were separated by chromatography and the structures of (CH(2)C(O)O)(6), (S,R,R,R,R,R)-(CHMeC(O)O)(6) and (S,S,R,R,R,R)-(CHMeC(O)O)(6) were determined. The (1)H and (13)C NMR data are reported for one of each of the six enantiomers of (CHMeC(O)O)(6) and the two meso isomers. The mechanism for the formation of these 18-membered rings is discussed in terms of an initial reaction between DMAP and NaBPh(4) in hot benzene that produces NaPh and DMAP:BPh(3) in the presence of the monomer lactide. The cyclic esters (CHMeC(O)O)(6) can also be obtained from the reaction between polylactide, PLA, in the presence of DMAP and NaBPh(4). The cyclic esters 3-methyl-1,4-dioxane-2,5-dione and 3,6,6-trimethyl-1,4-dioxane-2,5-dione undergo similar ring enlarging reactions to give cyclic 18-membered ring esters as determined by ESI-MS.     

Conformationally restricted 4-dimethylaminopyridine (DMAP) analogs: synthesis and evaluation of catalytic effectiveness

The syntheses of a series of conformationally restricted 4-dimethylaminopyridine (DMAP) analogs 1-3 are described. Evaluations of catalyst effectiveness demonstrated that 1 was the best catalyst for the acetylation reaction of a tertiary alcohol, while 2 and 3 were roughly comparable to DMAP. The order of effectiveness of these catalysts roughly parallels their acetylation enthalpies estimated from ab initio calculations.     

Visible Light-Gated Organocatalysis Using a RuII-Photocage

The light-gated organocatalysis via the release of 4-N,N-dimethylaminopyridine (DMAP) by irradiation of the [Ru(bpy)₂(DMAP)₂]²⁺ complex with visible light was investigated. As model reaction the acetylation of benzyl alcohols with acetic anhydride was chosen. The pre-catalyst releases one DMAP molecule on irradiation at wavelengths longer than 455 nm. The photochemical process was characterized by steady-state irradiation and ultrafast transient absorption spectroscopy. The latter enabled the observation of the ³MLCT state and the spectral features of the penta-coordinated intermediate [Ru(bpy)₂(DMAP)]²⁺. The released DMAP catalyzes the acetylation of a wide range of benzyl alcohols with chemical yields of up to 99 %. Control experiments revealed unequivocally that it is the released DMAP which takes the role of the catalyst.     

脂肪醇聚氧乙烯醚羟值的检测方法的改进

以4-二甲氨基吡啶为催化剂,过量乙酸酐为乙酰化试剂,吡啶为溶剂,用电位滴定法快速测定脂肪醇聚氧乙烯醚(AEO)的羟值,并对催化剂、反应条件、系统的适应性进行了探讨。用该方法对5种不同羟值的AEO样品进行了测定,测定结果的相对标准偏差0.5%(n=6),且测定结果与国标法测定结果的相对误差在±1%之内。     

Influence of synthetic routes on the conformational order and mobility of C18 and C30 stationary phases

Silica gels modified with n-alkyl chains (n = 18, 30) are prepared by two different synthetic routes and are examined by variable temperature FTIR and solid-state NMR spectroscopy. HPLC measurements of SRM 869, cis/trans ss-carotene isomers and xanthophylls isomers confirm the dependence of the separation mechanism on the alkyl chain length and the synthetic routes. The determination of the silane functionality and degree of cross-linking of silane ligands on the silica surface is achieved by 29Si CP/MAS NMR measurements. The structural order and mobility of the alkyl chains are investigated by means of variable temperature 13C CP/MAS NMR measurements. Variable temperature FTIR studies are performed where conformational order and flexibility of the alkyl chains in C18 and C30 phases are monitored through conformational sensitive CH2 symmetric, anti-symmetric stretching and wagging modes. In addition, the chromatographic properties of the C18 and C30 phases are determined. The results derived from the FTIR, NMR and HPLC measurements are discussed in the context of the applied synthetic routes and alkyl chain lengths.     

布洛芬-扑热息痛孪药的合成

以布洛芬（IPF）和扑热息痛（PCM）为原料,无水丙酮和乙酸乙酯为溶剂,二环己基碳二亚胺（DCC）为脱水剂,4-二甲氨基吡啶（DMAP）为催化剂,合成了布洛芬-扑热息痛孪药（PHI）,以重结晶法对目标产物进行纯化,产物结构经IR和1H NMR确定。 探讨了原料比例、脱水剂用量、催化剂用量、反应时间和溶媒用量对目标物产率的影响,并采用正交试验筛选最优合成工艺,最终确定的最优反应条件为:n(PCM)∶n(IPF)=1∶1.5,催化剂的最佳用量为布洛芬质量的10%,反应时间为8 h,溶媒体积为70 mL（V(乙酸乙酯)∶V(丙酮)=1∶1）,在该条件下,目标物PHI的产率为66.53%。     

Surface modification of functional self-assembled monolayers on 316L stainless steel via lipase catalysis

Lipase catalyzed esterification of therapeutic drugs to functional self-assembled monolayers (SAMs) on 316L stainless steel (SS) after assembly has been demonstrated. SAMs of 16-mercaptohexadecanoic acid (-COOH SAM) and 11-mercapto-1-undecanol (-OH SAM) were formed on 316L SS, and lipase catalysis was used to attach therapeutic drugs, perphenazine and ibuprofen, respectively, on these SAMs. The reaction was carried out in toluene at 60 degrees C for 5 h using Novozyme-435 as the biocatalyst. The FTIR spectra after surface modification of -OH SAMs showed the presence of the C=O stretching bands at 1745 cm(-1), which was absent in the FTIR spectra of -OH SAMs. Similarly, the FTIR spectra after the reaction of the -COOH SAM with perphenazine showed two peaks in the carbonyl region, a peak at 1764 cm(-1), which is the representative peak for the C=O stretching for esters. The second peak at 1681 cm(-1) is assigned to the C=O stretching of the remaining unreacted terminal COOH. XPS spectra after lipase catalysis with ibuprofen showed a photoelectron peak evolving at 288.5 eV which arises from the carbon (C=O) of the carboxylic acid of the drug (ibuprofen). Similarly for -COOH SAMs, after esterifiation we see a small, photoelectron peak evolving at 286.5 eV which corresponds to the C in the methylene groups adjacent to the oxygen (C-O), which should evolve only after the esterification of perphenazine with the -COOH SAM. Thus, lipase catalysis provides an alternate synthetic methodology for surface modification of functional SAMs after assembly.     

Effect of surface coverage on the conformation and mobility of C18-modified silica gels

C18-modified silica gels with surface coverages of 2 to 8.2 micromol m(-2), were prepared by different synthetic pathways and characterized by Fourier Transform infrared spectroscopy (FTIR), solid-state nuclear magnetic resonance (NMR) spectroscopy, and chromatographic measurements. The effects of temperature and bonding density on the conformational order of C18-modified silica gels were studied in detail by FTIR spectroscopy. The silane functionality and degree of cross-linking of silane ligands on the silica surface were evaluated by 29Si cross-polarization magic-angle spinning (CP/MAS) NMR and the structural order and mobility of the alkyl chains were investigated by 13C CP/MAS NMR spectroscopy. CH2 symmetric and anti-symmetric stretching bands and CH2 wagging bands were used as IR probes to monitor the conformational order and flexibility of the alkyl chains in the C18 phases. Qualitative information about the conformational order was obtained from frequency shifts of the CH2 symmetric and anti-symmetric stretching bands. The relative amounts of kink/gauche-trans-gauche, double-gauche, and end-gauche conformers in the alkyl chains were determined by analysis of CH2 wagging bands. These results indicate that surface coverage plays a dominant role in the conformational order of C18-modified silica gels. The FTIR and NMR data are discussed in the context of the chromatographic shape-selectivity differences.     

4-N,N-Dimethylaminopyridine promoted selective oxidation of methyl aromatics with molecular oxygen

4-N,N-Dimethylaminopyridine (DMAP) as catalyst in combination with benzyl bromide was developed for the selective oxidation of methyl aromatics. DMAP exhibited higher catalytic activity than other pyridine analogues, such as 4-carboxypyridine, 4-cyanopyridine and pyridine. The sp3 hybrid carbon-hydrogen (C-H) bonds of different methyl aromatics were successfully oxygenated with molecular oxygen. The real catalyst is due to the formation of a pyridine onium salt from the bromide and DMAP. The onium salt was well characterized by NMR and the reaction mechanism was discussed.     

Isotopic study of new fundamentals and combination bands of linear C5, C7, and C9 in solid ar

A high yield of carbon chains has been produced by the laser ablation of carbon rods having (13)C enrichment. FTIR spectroscopy of these molecules trapped in solid Ar has resulted in the identification of two new combination bands for linear C(5) and C(9). The (ν(1) + ν(4)) combination band of linear C(5) has been observed at 3388.8 cm(-1), and comparison of (13)C isotopic shift measurements with the predictions of density functional theory calculations (DFT) at the B3LYP/cc-pVDZ level makes possible the assignment of the ν(1)(σ(g)(+)) stretching fundamental at 1946 cm(-1). Similarly, the observation of the (ν(2) + ν(7)) combination band of linear C(9) at 3471.8 cm(-1) enables the assignment of the ν(2)(σ(g)(+)) stretching fundamental at 1871 cm(-1). The third and weakest of the infrared stretching fundamentals of linear C(7), the ν(6)(σ(u)(+)) fundamental at 1100.1 cm(-1), has also been assigned.     

The Garfield and Uley nontronites--an infrared spectroscopic comparison

FTIR and Infrared emission spectroscopy (IES) has been used to characterise the Uley (Australian) and Garfield nontronites. These clay minerals are characterised by a strong emission band at 3570 cm(-1) attributed to the FeFeOH unit. Dehydroxylation is followed by the loss of intensity of this band as a function of temperature. Dehydroxylation is also followed by the loss of intensity of the FeFeOH deformation vibration at 843 cm(-1). IES shows that the dehydroxylation occurs as a continuous process in comparison to DTA/TGA studies where the dehydroxylation occurs abruptly at 425 degrees C. Water in these high iron bearing smectites have been observed through the stretching mode at 3430 cm(-1) and the bending mode at 1630 cm(-1). Different types of water are identified in the nontronite structure by the analysis of the band profile in the 1590-1680 cm(-1) region. Low frequency vibrations show that the Uley green nontronite is similar to the Garfield nontronite. The brown Uley nontronite is closer to the Hohen-Hagen nontronite. The Uley nontronites may, therefore, be used spectroscopically to replace other nontronites as a reference clay mineral.