Natural Deep Eutectic Solvent (NADES) Extraction Improves Polyphenol Yield and Antioxidant Activity of Wild Thyme (Thymus serpyllum L.) Extracts

Wild thyme (Thymus serpyllum L.) herbal dust has been recognized as a potential underutilized resource for the recovery of antioxidants. The aim of this paper was to optimize natural deep eutectic solvent (NADES) extraction of polyphenols to obtain improved antioxidant activity of extracts determined by selected in vitro assays (DPPH, FRAP, and ABTS). Twenty different NADES systems were investigated in the first step of the screening of the extraction solvent and l-proline (Pro)–glycerine (Gly) based solvents provided the best results. Preliminary experiments organized by 2⁵⁻¹ fractional factorial design narrowed down the number of extraction factors from five (temperature, extraction time, NADES type, water content and L/S ratio) to three and determined their experimental domain for the final step. A face-centered central composite design with temperature (40–55–70 °C), extraction time (60–120–180 min) and L/S ratio (10–20–30 g NADES/g sample) was applied for influence analysis and process optimization. Multi-response optimization suggested a temperature of 65 °C, time of extraction of 180 min and L/S ratio of 28 g NADES/g DW as optimal extraction parameters. Experimental validation confirmed good agreement between experimental and predicted results in the extract obtained at optimal conditions and the interactions in the most suitable NADES (N16; Pro–Gly–H₂O; 1:2:1) were confirmed by the ¹H-NMR.     

改进的微波辅助无溶剂法提取薄荷和陈皮中的挥发油组分

An improved solvent free microwave extraction, in which a kind of microwave absorption medium （carbonyl iron powder） was used, was applied to the extraction of essential oil from dried menthol mint and orange peel without addition of any solvent and pretreatment. It took much less time of extraction （30 min） than microwave-assisted hydrodistillation （90 min） and conventional hydrodistillation （180 min）. The kinds of chemical compositions in essential oil extracted by different methods were almost the same and such improved solvent free microwave extraction can be a feasible way in extraction of essential oil from dried plant materials.     

Routine analysis of vinicultural relevant fungicides, insecticides and herbicides in soil samples using enhanced solvent extraction (ESE)

Parameters affecting the extraction efficiency of various pesticides from a native contaminated soil sample (C_org = 4.4%) using an enhanced solvent extraction (ESE) technique were investigated. The defined settings of temperature (50/150?°C), pressure (180/240 MPa), static and dynamic extraction time (5/15 min and 0/5 min, respectively) yielded results which did not differ significantly (RSD = 5.9–11.8%). In comparison to a classical shake-out extraction method the yielded quantities were on average 14% higher using ESE. The established method achieved a high precision (RSD = 2.8–9.1%) for the pesticides extracted from native contaminated soil samples. A significant influence of the sample matrix on accuracy was not observed. The RSDs of thirteen pesticides extracted from spiked sea sand varied in a similar range from 1.7 to 9.8% and the recoveries were between 83 and 112%. The method has been applied to soil samples from vineyards routinely.     

Pressurized solvent extraction and monolithic column-HPLC/DAD analysis of anthocyanins in red cabbage

The aim of this work was to develop a fast method for extraction and analysis of anthocyanins in red cabbage. Pressurized hot water containing 5% of ethanol was used as an extremely efficient extraction solvent. HPLC/DAD with a monolithic column was used to accomplish a fast analysis—24 anthocyanin peaks within 18 min. Statistical design was used to optimize the studied extraction parameters: temperature (80–120 °C); sample amount (1–3 g); extraction time (6–11 min); concentration of formic acid in the extraction solvent (0–5 vol.%). The best extraction conditions for a majority of the anthocyanin peaks were 2.5 g of sample, 99 °C (at 50 bar), 7 min of extraction and a solvent composition of water/ethanol/formic acid (94/5/1, v/v/v).     

Extract with high 1,1-diphenyl-2-picrylhydrazyl (DPPH) inhibitory capability from pericarp and seed of mangosteen (Garcinia mangostana L.) using microwave-assisted extraction (MAE) two-phase solvent technique

The human body needs compounds that are antioxidants to prevent oxidative stress. Some parts of the mangosteen fruit (Garcinia mangostana L.) have been known as sources of bioactive compounds that have antioxidant properties. The pericarp and seeds of mangosteen were extracted using the MAE method to produce the extract with the greatest antioxidant activity. There are two types of solvent mixtures used in the extraction process: single-phase and two-phase solvents. The solvents used were ethanol (EtOH), ethyl acetate (EtOAc), isopropyl alcohol (IPA), and water. First, utilizing dried mangosteen pericarp powder as the raw material, a study was undertaken to determine the ideal operating conditions for the MAE process. A one-factor-at-a-time approach was used to find the best operating conditions. A mixture of solvents with varied ratios (mL/mL), extraction temperature (°C), extraction time (min), and solid to solvent ratio (g/mL) were applied as independent variables. Then, dried mangosteen seed powder extraction was carried out based on the best-operating conditions previously achieved. The DPPH scavenging activity, total phenolic content (TPC) value, and α-mangostin content of the two extracts were compared. It was discovered that the mangosteen pericarp extract showed higher antioxidant activity (IC₅₀ DPPH = 9.40 µg/mL) than the mangosteen seed extract (IC₅₀ DPPH = 37.54 µg/mL), even slightly better than ascorbic acid (IC₅₀ DPPH = 10.47 µg/mL). The best extract was produced from the bottom phase of two-phase solvent system (EtOAc:EtOH:Water 2:1:2), with an MAE temperature of 50 °C, a time of 4 min, and a solid-to-solvent ratio of 1:16. The TPC value of the best extract is 903.54 mgGAE/g extract, with a yield of 16.53 % and an α-mangostin concentration of 0.11 %.     

Non-polar Solvent Microwave-Assisted Extraction of Volatile Constituents from Dried Zingiber Officinale Rosc.

A new method, non-polar solvent microwave-assisted extraction （NPSMAE）, was applied to the extraction of essential oil from Zingiber officinale Rosc. in closed-vessel system. By adding microwave absorption mediumcarbonyl iron powders （CIP） into extraction system, the essential oil was extracted by the non-polar solvent （ether） which can be heated by CIP. The constituents of essential oil obtained by NPSMAE were comparable with those obtained by hydrodistillation （HD） by GC-MS analysis, which indicates that NPSMAE is a feasible way to extract essential oil from dried plant materials. The NPSMAE took much less extraction time （5 min） than HD （180 min）, and its extraction efficiency was much higher than that of conventional polar solvent microwave-assisted extraction （PSMAE） and mixed solvent microwave-assisted extraction （MSMAE）. It can be a good alternative for the extraction of volatile constituents from dried plant samples.     

Routine analysis of vinicultural relevant fungicides, insecticides and herbicides in soil samples using enhanced solvent extraction (ESE)

Parameters affecting the extraction efficiency of various pesticides from a native contaminated soil sample (C_org = 4.4%) using an enhanced solvent extraction (ESE) technique were investigated. The defined settings of temperature (50/150 °C), pressure (180/240 MPa), static and dynamic extraction time (5/15 min and 0/5 min, respectively) yielded results which did not differ significantly (RSD = 5.9–11.8%). In comparison to a classical shake-out extraction method the yielded quantities were on average 14% higher using ESE. The established method achieved a high precision (RSD = 2.8–9.1%) for the pesticides extracted from native contaminated soil samples. A significant influence of the sample matrix on accuracy was not observed. The RSDs of thirteen pesticides extracted from spiked sea sand varied in a similar range from 1.7 to 9.8% and the recoveries were between 83 and 112%. The method has been applied to soil samples from vineyards routinely. Received: 28 December 1998 / Revised: 8 March 1999 / Accepted: 11 March 1999     

Separation and purification of furanocoumarins from Toddalia asiatica (L.) Lam. using microwave-assisted extraction coupled with high-speed counter-current chromatography

A method of microwave-assisted extraction coupled with high-speed counter-current chromatography was established for separation and purification of isopimpinellin, pimpinellin and phellopterin from Toddalia asiatica (L.) Lam. The conditions of MAE including the extraction solvent, size of sample, solid/liquid ratio, extraction temperature and extraction time were optimized by a mono-factor test. That is, 2.0 g dried powder of T. asiatica (L.) Lam of 0.30-0.15 mm size was extracted with 20 mL (solid/liquid ratio of 1:10, g/mL) methanol under 50 °C for 1 min. The crude extract was separated and purified by high-speed counter-current chromatography with hexane-ethyl acetate-methanol-water (5:5:5.5:4.5, v/v/v/v) solvent system. 0.85 mg/g of isopimpinellin, 2.55 mg/g of pimpinellin and 0.95 mg/g of phellopterin were obtained from original sample in one-step within 240 min, the purity determined by high performance liquid chromatography was 95.0%, 99.1% and 96.4%, respectively. Their chemical structures were further identified by mass spectroscopy and nuclear magnetic resonance spectroscopy. The results demonstrated that microwave-assisted extraction coupled with high-speed counter-current chromatography was a feasible, economical and efficient technique for rapid extraction, separation and purification of effective compounds from natural products.     

气流吹扫-注射器微萃取-全二维气相色谱法用于原油组分的表征

建立了气流吹扫-注射器微萃取（GP-MSE）与全二维气相色谱/飞行时间质谱（GC×GC/TOFMS）联用分析原油成分的方法。为了找到适用于原油样品分析的GP-MSE条件,用饱和烃混合标准溶液和15种芳烃的混合标准溶液进行了条件优化,得到的最佳条件如下:取样量5 mg、萃取溶剂正己烷20 μ L、载气流速2 mL/min、加热时间3 min、加热温度300 ℃、冷凝温度-2 ℃。处理后的样品在全二维色谱/飞行时间质谱上进样分析,得到了满意结果。方法的检出限为34~93 μg/L,线性相关系数（R²）>0.99,对50种烃类化合物的回收率在82.0%~107.3%之间,相对标准偏差<10%（n=5）。结果表明GP-MSE-GC×GC/TOFMS法是一种新型绿色、高效、灵敏的分析方法,非常适合原油中挥发性与半挥发性组分的分析。     

Vortex‐ and CO2‐gas‐assisted liquid–liquid microextraction with salt addition for the high‐performance liquid chromatographic determination of furanic compounds in concentrated juices and dried fruits

A novel microextraction method based on vortex‐ and CO₂‐assisted liquid–liquid microextraction with salt addition for the isolation of furanic compounds (5‐hydroxymethyl‐2‐furaldehyde, 5‐methyl‐2‐furaldehyde, 2‐furaldehyde, 3‐furaldehyde, 2‐furoic and 3‐furoic acids) was developed. Purging the sample with CO₂ was applied after vortexing to enhance the phase separation and mass transfer of the analytes. The optimum extraction conditions were: extraction solvent (volume), propyl acetate (125 μL); sample pH, 2.4; vortexing time, 45 s; salt concentration, 25% w/v and purging time, 5 min. The analytes were separated using an ODS Hypersil C₁₈ column (250×4.6 mm i.d, 5 μm) under gradient flow. The proposed method showed good linearities (r² >0.999), low detection limits (0.08–1.9 μg/L) and good recoveries (80.7–122%). The validated method was successfully applied for the determination of the furanic compounds in concentrated juice (mango, date, orange, pomegranate, roselle, mangosteen and soursop) and dried fruit (prune, date and apricot paste) samples.     

分散液液微萃取-反相液液微萃取-扫集-胶束电动色谱法测定红酒中的3种氯酚类物质

建立了分散液液微萃取（DLLME）-反相液液微萃取（RP-LLME）-扫集-胶束电动色谱富集模型,并用于红酒中五氯酚（PCP）、2,4,6-三氯酚（TCP）和2,4-二氯酚（DCP）3种氯酚的测定。实验考察了两步微萃取的萃取参数对氯酚萃取率的影响和样品分离富集的电泳条件。最佳萃取条件DLLME为：3.5 mL红酒（pH 3.0,120 g/L NaCl）,300 μL正己烷（萃取剂）;RP-LLME为：25 μL 0.16 mol/L NaOH（萃取剂）。最佳电泳条件：25 mmol/L NaH₂PO₄,100 mmol/L十二烷基硫酸钠（SDS）,30%（v/v）乙腈,pH 2.3;分离电压-15 kV;样品基质为80 mmol/L NaH₂PO₄;压力进样20 s×20.67 kPa（3 psi）。PCP和TCP的线性范围为0.5~100 μg/L（r≥0.9910）,DCP的线性范围为1.5~80 μg/L（r=0.9851）。3种分析物的检出限（S/N=3）为0.035~0.114 μg/L,加标回收率为75.2%~104.7%,相对标准偏差≤6.17%。该方法富集倍数高、灵敏度高、重现性好、分析速度快,可为不同样品基质中痕量氯酚污染物及某些弱酸性有机污染物测定提供参考。     

Synthesis of molecular imprinted polymer nanoparticles followed by application of response surface methodology for optimization of metribuzin extraction from urine samples

A molecular imprinted polymer was prepared with precipitation polymerization technique and applied as a sorbent for selective extraction and enrichment of metribuzin herbicide prior to high performance liquid chromatography. Optimization of critical variables affecting the efficiency of molecularly imprinted solid-phase extraction (MISPE), such as sorbent mass, sample pH and flow rate of sample, volume, concentration, and flow rate of elution solvent was done by employing central composite design (CCD) of the response surface methodology. Two separate models were developed for the adsorption and recycling steps. The analysis of variance (ANOVA) demonstrated that, experimental data were excellently fitted to the proposed response models. The optimum operating conditions were: a sorbent mass of 25 mg, sample pH 6.19, sample flow rate of 2.15 mL/min, and a 5 mL portion of methanol/acetic acid with 92.7:7.3 (v/v) ratio and flow rate of 2.1 mL/min for the extraction process. Under the optimized conditions, the linear range was obtained from 20 to 120 µg/L (R²?=?0.999) and the lowest detectable concentration (LOD) and the lowest quantitative concentration (LOQ) were calculated as 5.75 and 19.86 µg/L, respectively. Finally, the designed MISPE method was successfully applied to determine trace amount of metribuzin in real samples. The diluted urine samples were spiked with metribuzin at 4 levels and extracted with recoveries ranging from 93.82 to 97.84% and the relative standard deviation (RSD) less than 4.8%.     

Bioguided extraction of polyphenols from grape marc by using an alternative supercritical-fluid extraction method based on a liquid solvent trap

The biological activity of polyphenols extracted from grape marc was studied with a view to finding a new use for this winery waste. Polyphenols were extracted by using an alternative supercritical-fluid extraction method based on the use of a liquid trap that allows extracted polyphenols to be retained in a saline buffer, thus avoiding the need for the organic solvent required to elute polyphenols from a solid trap. The major extraction variables influencing the performance of the liquid trap (viz. CO₂ modifier content, flow-rate, extraction time and trap volume) were optimized. The proposed method was applied to the supercritical-fluid extraction extraction of 0.3 g grape marc with CO₂ modified with 3% methanol at 350 bar at 50 °C (CO₂ density 0.9 g mL^-1) for 20 min, using a liquid flow-rate of 0.9 mL min^-1. The polyphenol extracts thus obtained exhibited cytotoxic effects that induced apoptosis in tumour cells.     

Rapid analysis of the essential oil components of dried Zanthoxylum bungeanum Maxim by Fe2O3‐magnetic‐microsphere‐assisted microwave distillation and simultaneous headspace single‐drop microextraction followed by GC–MS

In this work, microwave distillation assisted by Fe₂O₃ magnetic microspheres (FMMS) and headspace single‐drop microextraction were combined, and developed for determination of essential oil compounds in dried Zanthoxylum bungeanum Maxim (ZBM). The FMMS were used as microwave absorption solid medium for dry distillation of dried ZBM. Using the proposed method, isolation, extraction, and concentration of essential oil compounds can be carried out in a single step. The experimental parameters including extraction solvent, solvent volume, microwave power, irradiation time, and the amount of added FMMS, were studied. The optimal analytical conditions were: 2.0 μL decane as the extraction solvent, microwave power of 300 W, irradiation time of 2 min, and the addition of 0.1 g FMMS to ZBM. The method precision was from 4 to 10%. A total of 52 compounds were identified by the proposed method. The conventional steam distillation method was also used for the analysis of essential oil in dried ZBM and only 31 compounds were identified by steam distillation method. It was found that the proposed method is a simple, rapid, reliable, and solvent‐free technique for the determination of volatile compounds in Chinese herbs.     

Separation and determination of ciprofloxacin in seawater,human blood plasma and tablet samples using molecularly imprinted polymer pipette‐tip solid phase extraction and its optimization by response surface methodology

By synthesizing a molecular imprinted polymer as an efficient adsorbent, ciprofloxacin was micro‐extracted from seawater, human blood plasma and tablet samples by pipette‐tip micro solid phase extraction and determined spectrophotometrically. Response surface methodology was applied with central composite design to build a model based on factors affecting on microextraction of ciprofloxacin; including volume of eluent solvent, number of extraction cycles, number of elution cycles, and pH of sample. Other factors that affect extraction efficiency, such as type of eluent solvent, volume of sample, type, and amount of salt were optimized with one‐variable‐at‐a‐time method. Under optimum extraction condition, pH of sample solution was 7.0, volume of eluent solvent (methanol) was 200 µL, volume of sample solution was 10 mL, and the number of extraction and elution cycles was five and seven, respectively, amount of Na₂SO₄ (as salt) and MIP (as sorbent) were optimized at 150 and 2 mg, respectively. The linear range of the suggested method under optimum extraction factors was 5–150 µg/L with a limit of detection of 1.50 µg/L for the analyte. Reproducibility of the method (as relative standard deviation) was better than 7%.     

Application of accelerated solvent extraction to the investigation of saikosaponins from the roots of Bupleurum falcatum

Accelerated solvent extraction (ASE) was applied to the extraction of saikosaponin a, saikosaponin c and saikosaponin d from the roots of Bupleurum falcatum. Main extraction parameters such as the extraction solvents, extraction temperature and static extraction time were investigated and optimized. The optimized procedure employed 70% methanol as extraction solvent, 120°C of extraction temperature, 10 min of static extraction time, 60% of flush volume and the extraction recoveries of the three compounds were near to 100% with one extraction cycle. The extracted samples were analyzed by HPLC with UV detector. The HPLC conditions were as follows: Hypersil ODS2 (4.6 mm×250 mm, 5 μm) column, acetonitrile and water as mobile phase, flow rate of 1.0 mL/min, UV detection wavelength of 204 nm and injection volume of 20 μL. Compared with the traditional methods including heat‐reflux extraction and ultrasonic‐assisted extraction, the proposed ASE method was more efficient and faster to be operated. The results indicated that ASE was an alternative method for extracting saikosaponins from the roots of B. falcatum.     

Ultrasonic Nebulization Extraction Coupled with Gas Chromatography-Mass Spectrometry for Analysis of Volatile Components in Traditional Chinese Patent Medicine

The ultrasonic nebulization extraction(UNE) was developed and applied to the extraction of volatile components from traditional Chinese patent medicine Xiaoyao Pills. Several parameters of ultrasonic nebulization extraction including the sample particle size, solvent volume, extraction time and ultrasonic power were studied and selected. As a result, 2.4 g of sample with particle size of 80 mesh was extracted with 15 mL of n-hexane for 20 min at an ultrasonic power of 35 W. The volatile components were anal...     

Supercritical carbon dioxide extraction of ubiquinones and menaquinones from activated sludge

Supercritical CO2 (scCO2) extraction, with methanol as modifier, was applied to the determination of ubiquinones and menaquinones in activated sludge. Four ubiquinones and 12 menaquinones species were identified based on retention time and UV spectrum in 0.1g dried activated sludge. The optimum extraction conditions were at a pressure of 25 MPa, a temperature of 55 degrees C, and 10% (v/v) methanol for 15 min. At this condition, the concentrations of extracted ubiquinones and menaquinones were found to be 0.181 and 0.326 micromol/g-dry-cell, respectively. The results were comparable with those obtained by organic solvent extraction based on diversity and dissimilarity indices. Furthermore, the method was evaluated in term of repeatability, which resulted in an RSD of < or =10%. The experimental results have demonstrated the technique to be simple, fast, and with less consumption of organic solvents. This work shows the potential application of supercritical CO2 extraction to microbial community analysis using quinone profile.     

Rapid determination of bisphenol A in drinking water using dispersive liquid‐phase microextraction with in situ derivatization prior to GC‐MS

This paper described a novel approach for the determination of bisphenol A by dispersive liquid‐phase microextraction with in situ acetylation prior to GC‐MS. In this derivatization/extraction method, 500 μL acetone (disperser solvent) containing 30.0 μL chlorobenzene (extraction solvent) and 30.0 μL acetic anhydride (derivatization reagent) was rapidly injected into 5.00 mL aqueous sample containing bisphenol A and K₂CO₃ (0.5% w/v). Within a few seconds the analyte was derivatized and extracted at the same time. After centrifugation, 1.0 μL of sedimented phase containing enriched analyte was determined by GC‐MS. Some important parameters, such as type and volume of extraction and disperser solvent, volume of acetic anhydride, derivatization and extraction time, amount of K₂CO₃, and salt addition were studied and optimized. Under the optimum conditions, the LOD and the LOQ were 0.01, 0.1 μg/L, respectively. The experimental results indicated that there was linearity over the range 0.1–50 μg/L with coefficient of correlation 0.9997, and good reproducibility with RSD 3.8% (n = 5). The proposed method has been applied for the analysis of drinking water samples, and satisfactory results were achieved.     

Simultaneous derivatization and extraction of anilines in waste water with dispersive liquid-liquid microextraction followed by gas chromatography-mass spectrometric detection

The one-step derivatization and extraction technique for the determination of anilines in river water by dispersive liquid-liquid microextraction (DLLME) is presented. In this method the anilines are extracted by DLLME and derivatized with pentafluorobenzaldehyde (PFBAY) in aqueous solution simultaneously. In this derivatization/extraction method, 0.5 ml acetone (disperser solvent) containing 10 microl chlorobenzene (extraction solvent) and 30 g/l pentafluorobenzaldehyde (PFBAY) dissolved in methanol was rapidly injected by syringe into 5 ml aqueous sample (pH 4.6). Within 20 min the analytes extracted and derivatized were almost finished. After centrifugation, 2 microl sedimented phase containing enriched analytes was determined by GC-MS. The effects of extraction and disperser solvent type and their volume, pH value of sample solution, derivatization and extraction time, derivatization and extraction temperature were investigated. Linearity in this developed method was ranging from 0.25 to 70 microg/l, and the correlation coefficients (R2) were between 0.9955 and 0.9989, and reasonable reproducibility ranging from 5.8 to 11.8% (n=5). Method detection limits (MDLs) ranged from 0.04 to 0.09 microg/l (n=5).