Extraction of crocin from saffron (Crocus sativus) using molecularly imprinted polymer solid‐phase extraction

A new molecularly imprinted polymer for extraction of crocin from saffron stigmas was prepared using gentiobiose (a glycoside moiety in crocin structure) as a template. Crocin binding to gentiobiose imprinted polymer (Gent‐MIP) was studied in comparison with a blank nonimprinted polymer in aqueous media. Affinity of the Gent‐MIP for the crocin was more than the nonimprinted polymer at all concentrations. In Scatchard analysis, the number of binding sites in each gram of polymer (maximum binding sites) and dissociation constant of crocin to binding sites were 18.4 μmol/g polymer and 11.2 μM, respectively. The Gent‐MIP was then used as the sorbent in an SPE method for isolation and purification of crocin from methanolic extract of saffron stigmas. The recovery of crocin, safranal and picrocrocin was determined in washing and elution steps. The Gent‐MIP had significantly higher affinity for crocin than other compounds and enabled selective extraction of crocin with a high recovery (84%) from a complex mixture. The results demonstrated the possibility of using a part of a big molecule in preparing a molecularly imprinted polymer with a good selectivity for the main structure.     

Synthesis and study of a molecularly imprinted polymer for specific solid‐phase extraction of vinflunine and its metabolite from biological fluids

A molecularly imprinted polymer (MIP) was synthesized in order to specifically extract vinflunine, an anticancer agent, and its metabolite (4‐O‐deacetylvinflunine) from bovine plasma and artificial urine by solid‐phase extraction (SPE). Vinorelbine, a non‐fluorinated analogue of vinflunine, was selected as a template for MIP synthesis. The selectivity of MIP versus the template (vinorelbine) and other alkaloids (catharanthine, vinblastine, vincristine, vinflunine and 4‐O‐deacetylvinflunine) was shown by a SPE protocol carried out with non‐aqueous samples. A second protocol was developed for aqueous samples with two consecutive washing steps (AcOH–NH₂OH buffer (pH 7, I=10 mM)–MeOH mixture 95:5 v/v and ACN–AcOH mixture 99:1 v/v) and an elution step (MeOH–AcOH mixture 90:10 v/v). Thus, MIP‐SPE of bovine plasma brought high recoveries, 81 and 89% for vinflunine and its metabolite, respectively. This protocol was slightly modified for artificial urine samples in order to obtain a good MIP/NIP selectivity; furthermore, elution recoveries were 73 and 81% for vinflunine and its metabolite, respectively. Repeatability was assessed in both biological matrices and RSD (%) were inferior to 4%. The MIP also showed a suitable linearity (r² superior to 0.99), between 0.25 and 10 μg/mL for plasma, and between 1 and 5 μg/mL for artificial urine.     

Development of a molecularly imprinted solid‐phase extraction sorbent for the selective extraction of telmisartan from human urine

A novel molecularly imprinted solid‐phase extraction with spectrofluorimetry method has been developed for the selective extraction of telmisartan from human urine. Molecularly imprinted polymers were prepared by a noncovalent imprinting approach through UV‐radical polymerization using telmisartan as a template molecule, 2‐dimethylamino ethyl methacrylate as a functional monomer, ethylene glycol dimethacrylate as a cross‐linker, N,N‐azobisisobutyronitrile as an initiator, chloroform as a porogen. Molecularly imprinted polymers and nonimprinted control polymer sorbents were dry‐packed into solid‐phase extraction cartridges, and eluates from cartridges were analyzed using a spectrofluorimeter. Limit of detection and limit of quantitation values were 11.0 and 36.0 ng/mL, respectively. A very high imprinting factor (16.1) was achieved and recovery values for the telmisartan spiked in human urine were in the range of 76.1–79.1%. In addition, relatively low within‐day (0.14–1.6%) and between‐day (0.11–1.31%) precision values were obtained. Valsartan was used to evaluate the selectivity of sorbent as well. As a result, a sensitive, selective, and simple molecularly imprinted solid‐phase extraction with spectrofluorimetry method has been developed and successfully applied to the direct determination telmisartan in human urine.     

Zwitterionic molecularly imprinted polymer‐based solid‐phase micro‐extraction coupled with molecularly imprinted polymer sensor for ultra‐trace sensing of L‐histidine

The proposed L ‐histidine sensing system composed of a molecularly imprinted solid‐phase microextraction component combined with a molecularly imprinted polymer sensor was used to determine critical levels of test analyte in a complex matrix of highly diluted human blood serum without any non‐specific sorption and false‐positive contributions. The molecularly imprinted polymer was a zwitterionic polymer brush derived from the disodium salt of EDTA and chloranil, grafted to solid‐phase microextraction material. The hyphenated approach was able to detect L ‐histidine quantitatively with a limit of detection as low as 0.0435 ng/mL (RSD = 0.2%, S/N = 3).     

Selective extraction of clonazepam from human plasma and urine samples by molecularly imprinted polymeric beads

A molecularly imprinted polymer (MIP) based on free‐radical polymerization was prepared with 1‐(N,N‐biscarboxymethyl)amino‐3‐allylglycerol and N,N‐dimethylacrylamide as functional monomers, N,N‐methylene diacrylamide as the cross‐linker, copper ion‐clonazepam as the template and 2,2‐azobis(2‐methylbutyronitrile) as the initiator. The imprinted polymer was characterized by Fourier transform infrared spectroscopy, elemental analysis, thermogravimetric analysis, and SEM. The MIP of agglomerated microparticles with multipores was used for SPE. The imprinted polymer sorbent was selective for clonazepam. The optimum pH and sorption capacity were 5 and 0.18 mg/g at 20°C, respectively. The profile of the drug uptake by the sorbent reflects good accessibility of the active sites in the imprinted polymer sorbent. The MIP‐SPE was the most feasible technique for the extraction of clonazepam with a high recovery from human plasma and urine samples.     

Preconcentration of indapamide from human urine using molecularly imprinted solid‐phase extraction

A simple, sensitive, and selective molecularly imprinted solid‐phase extraction and spectrophotometric method has been developed for the clean‐up and preconcentration of indapamide from human urine. Molecularly imprinted polymers were prepared by a non‐covalent imprinting approach using indapamide as a template molecule, 2‐(trifluoromethyl) acrylic acid as a functional monomer, ethylene glycol dimethacrylate as a crosslinker, N,N‐azobisisobutyronitrile as a thermal initiator and acetonitrile as a porogenic solvent. A non‐imprinted polymer was also prepared in the same way, but in the absence of template. Molecularly imprinted polymer and non‐imprinted polymer sorbents were dry‐packed into solid‐phase extraction cartridges. Eluates from cartridges were analyzed using a spectrophotometer for the determination of indapamide by referring to the calibration curve in the range 0.14–1.50 μg/mL. Preconcentration factor, limit of detection, and limit of quantification were 16.30, 0.025 μg/mL, and 0.075 μg/mL, respectively. A relatively high imprinting factor (9.3) was also achieved and recovery values for the indapamide spiked into human urine were in the range of 80.1–81.2%. In addition, relatively low within‐day (0.17–0.42%) and between‐day (1.1–1.4%) precision values were obtained as well. The proposed molecularly imprinted solid‐phase extraction and spectrophotometric method was successfully applied to selective extraction, preconcentration, and determination of indapamide from human urine samples.     

Molecularly imprinted probe for solid‐phase extraction of hippuric and 4‐methylhippuric acids directly from human urine samples followed by MEKC analysis

Hippuric acid (HA) and 4‐methylhippuric acid (4‐MHA) are metabolites as well as biological indicators for toluene and xylenes, respectively, and their determination in urine samples is very important, in order to monitor the occupational exposition to these solvents, ensuring a safe working environment. Thus, this paper describes the synthesis and characterization of a probe impregnated with molecularly imprinted polymers (MIPs) for the solid‐phase extraction of HA and 4‐MHA directly from untreated urine samples followed by micellar electrokinetic chromatography (MEKC) analyses. The MIP probe selectivity was compared to the non‐imprinted polymer probe. The MEKC separations were carried out in 50 mmol/L sodium tetraborate pH 10.0/0.5 mmol/L cetyltrimethylammonium bromide aqueous solution, with a constant voltage of –15 kV. The system variables were optimized to provide ideal conditions for the extraction and desorption of the analytes, as well as for the MEKC analyses. The method was linear from 0.5 to 5.0 g/L for both analytes, with correlation coefficients > 0.994. Precisions and accuracies, expressed as relative standard deviation and relative error, were < 20.0 and within –15.4 to 16.6%, respectively, in accordance with the United States Food and Drug Administration recommendation. The MIP probe has proven to be simple, cheap, resistant, and synthetically reproducible, being successfully used to analyze both HA and 4‐MHA from real samples.     

Molecularly imprinted polymer‐based solid phase clean‐up for analysis of ochratoxin A in beer,red wine,and grape juice

A simple, reliable, and low‐cost method based on molecularly imprinted polymer as a selective sorbent of SPE was proposed for the determination of ochratoxin A (OTA) in beer, red wine, and grape juice by HPLC coupled with fluorescence detection (HPLC‐FLD). Samples were diluted with water and cleaned up with an AFFINIMIP® SPE OTA column. After washing and eluting, the analyte was analyzed by HPLC‐FLD. Under the optimized conditions, LOD and LOQ for OTA were 0.025 and 0.08 ng/mL, respectively. The recoveries of OTA from beer, red wine, and grape spiked at 0.1, 2, and 5 ng/mL ranged from 91.6 to 101.7%. Furthermore, after a simple regenerated procedure, the molecularly imprinted polymer based SPE column could be reused at least 14 times to achieve more than 80% recoveries of OTA in real samples. The developed method was applied to the detection of 30 beer, red wine, and grape juice samples and only four samples were contaminated by OTA with levels below the legal limits.     

Molecularly imprinted solid phase extraction for rapid screening of cephalexin in human plasma and serum

A molecularly imprinted solid phase extraction (MISPE) method was developed for the rapid screening of cephalexin in human plasma and serum. The method employed a micro-column packed with molecularly imprinted polymer (MIP) particles for the selective solid phase extraction (SPE) of cephalexin. Since the MIP interacted indiscriminately with two other α-aminocephalosporins, cefradine and cefadroxil, their removal was ultimately achieved using differential pulsed elution (DPE) with acetonitrile+12% acetic acid. Cephalexin was then determined in a final pulsed elution (FPE) with methanol+1% trifluoroacetic (CF₃COOH, TFA) acid. This excellent selectivity represents a significant advance in analytical separation, demonstrating how a MIP can differentiate between molecules that are structurally dissimilar only in their non-hydrogen-bonding moieties, even if their hydrogen-bonding moieties are identical to each other. With UV detection, a concentration detection limit of 0.1 μg/ml (or 2 ng in 20 μl) was afforded for cephalexin. By increasing the CHCl₃ flow rate to 1.25 ml/min, each MISPE-DPE-FPE analysis required only 2 min to complete. Rapid screening was demonstrated in a modified MISPE-PE method, which used 14% CH₃COOH+CH₃CN as the mobile phase, followed by direct PE with 1% TFA+CH₃OH.     

Molecularly imprinted polymers for the solid‐phase extraction of four fluoroquilones from milk and lake water samples

A method based on molecular crowding and ionic liquids as reaction solvents has been used for the synthesis of molecularly imprinted polymers. Levofloxacin was selected as the template, polymethyl methacrylate was the molecular crowding agent, and 1‐butyl‐3‐methylimidazolium tetrafluoroborate (ionic liquid) was selected as the reaction solvent and porogen. The optimized proportion for the mixed porogen was dimethyl sulfoxide/ionic liquid/polymethyl methacrylate 1:1.6:5 in chloroform (150 mg mL^?1). The morphology and chemical composition of levofloxacin imprinted polymers were assessed by scanning electron microscopy and Fourier transform infrared spectroscopy. The absorption experiments demonstrated that the levofloxacin imprinted polymers possess high selective recognition property to levofloxacin and analogs, including enrofloxacin, ciprofloxacin and gatifloxacin, which all belong to fluoroquinolones. An extraction method using levofloxacin imprinted polymers as sorbent followed by high‐performance liquid chromatography analysis was optimized for the determination of four fluoroquinolones in milk and lake water samples. Under the optimized conditions, good linearity was observed in a range of 5–1000 ng g^?1 with the limit of detection between 0.3 and 0.5 ng g^?1 for the four fluoroquinolones. The recoveries at three spiked levels ranged 82.4–98.3% with the relative standard deviation ≤4.9.     

Efficient strategy for the selective determination of dopamine in human urine by molecularly imprinted solid‐phase extraction

An efficient molecularly imprinted solid‐phase extraction protocol was developed for the separation of dopamine (DA) from human urine. After successful validation of the analytical method using high‐performance liquid chromatography coupled with fluorescence detection, a new strategy for the selective determination of DA in the presence of norepinephrine and epinephrine in human urine was presented. In the proposed protocol, the LODs and quantification for DA were 166 ± 36 and 500 ± 110 nmol/L, respectively, and the total recoveries of DA in the range of 1–15 μmol/L varied between 98.3 and 101.1%. DA was detected in the real urine samples at the level of 47–167 μg/L (0.250–0.895 μmol/L). The superiority of the novel analytical strategy was shown by comparison with the results obtained for a commercially available imprinted sorbent.     

Molecularly imprinted polymer for the selective extraction of luteolin from Chrysanthemum morifolium Ramat

In this work, luteolin‐imprinted polymers were prepared by noncovalent precipitation polymerization for the first time. Their structural features and morphologies were analyzed by using Fourier transform infrared spectroscopy and scanning electron microscopy, respectively. The adsorption experiments revealed that the luteolin‐imprinted polymers presented high selective recognition property to luteolin. The selectivity experiment showed that the adsorption capacity and selectivity of polymers to luteolin was higher than that of three structural analogs, including quercetin, isorhamnetin, and ombuin. Furthermore, an efficient method based on luteolin‐imprinted polymers coupled with solid‐phase extraction was developed for the pretreatment of luteolin from Chrysanthemum morifolium Ramat. The results demonstrated that the luteolin‐imprinted polymers coupled with solid phase extraction method was proven to be a potentially competitive technique for the separation and enrichment of luteolin in complex samples such as Chinese patent medicines and biological samples.     

Synthesis of surface molecularly imprinted polymer and the selective solid phase extraction of imidazole from its structural analogs

A surface molecularly imprinted polymer (MIP) was synthesized by using imidazole as the template and modified silica particles as the support material. The static adsorption, solid phase extraction (SPE) and high-performance liquid chromatography (HPLC) experiments were performed to investigate the adsorption properties and selective recognition characteristics of the polymer for imidazole and its structural analogs. It was shown that the maximum binding capacities of imidazole on the MIP and the non-imprinted polymer (NIP) were 312 and 169 μmol g⁻¹, respectively. The adsorption was fast and the adsorption equilibrium was achieved in 30 min. The binding process could be described by pseudo-second order kinetics. Compared with the corresponding non-imprinted polymer, the molecularly imprinted polymer exhibited much higher adsorption performance and selectivity for imidazole. The selective separation of imidazole from a mixture of 1-hexyl-3-methylimidazolium bromide ([C₆mim][Br]) and 2,4-dichlorophenol could be achieved on the MIP-SPE column. The recoveries of imidazole and [C₆mim][Br] were 97.6-102.7% and 12.2-17.3%, respectively, but 2,4-dichlorophenol could not be retained on the column. The surface molecularly imprinted polymer presented here may find useful application as a solid phase absorbent to separate trace imidazole in environmental water samples. This may also form the basis for our research program on the preparation and application of alkyl-imidazolium imprinted polymers.     

Fast and selective extraction of chloramphenicol from soil by matrix solid‐phase dispersion using molecularly imprinted polymer as dispersant

The molecularly imprinted polymer (MIP) was synthesized and used as dispersant of matrix solid‐phase dispersion (MSPD) for the extraction of chloramphenicol (CAP) in soil samples. The satisfactory recovery of CAP was obtained by the optimized extraction conditions: 1:2 as the ratio of sample to MIPs; 5 min as the dispersion time; 30% aqueous methanol as washing solvent and methanol as elution solvent. The CAP extracted from soil was determined by LC‐MS/MS. The slight ion suppression phenomenon was observed for the CAP when the sample was cleaned up by MSPD with MIP as dispersant, when compared with C18 as MSPD dispersant, which caused significant ion suppression. LOD of CAP is 4.1 ng/g. RSDs of intra‐ and inter‐day tests ranging from 3.1 to 6.2% and from 3.9 to 8.3% are obtained. At all three fortified levels (20, 100 and 500 ng/g), recoveries of CAP are in the range of 86.9–92.6%. The effect of ageing time of spiked soil sample on the CAP recovery was examined. The CAP recovery decreased from 91.0 to 36.9% when the ageing time changed from 1 day to 4 wk.     

Molecularly imprinted polymer microspheres for solid-phase extraction of protocatechuic acid in Rhizoma homalomenae

Molecularly imprinted polymers (MIPs) had been prepared by precipitation polymerization method using acrylamide as the functional monomer, ethylene glycol dimethacrylate as the cross-linker, acetonitrile as the porogen solvent and protocatechuic acid (PA), one of phenolic acids, as the template molecule. The MIPs were characterized by scanning electron microscopy and Fourier transform infrared, and their performance relative to non-imprinted polymers was assessed by equilibrium binding experiments. Six structurally similar phenolic acids, including p-hydroxybenzoic acid, gallic acid, salicylic acid, syringic acid, vanillic acid, ferulic acid were selected to assess the selectivity and recognition capability of the MIPs. The MIPs were applied to extract PA from the traditional Chinese medicines as a solid-phase extraction sorbent. The resultant cartridge showed that the MIPs have a good extraction performance and were able to selectively extract almost 82% of PA from the extract of Rhizoma homalomenae. Thus, the proposed molecularly imprinted-solid phase extraction-high performance liquid chromatography method can be successfully used to extract and analyse PA in traditional Chinese medicines.     

Molecularly imprinted polymer for selective extraction of 3-methylflavone-8-carboxylic acid from human urine followed by its determination using zwitterionic hydrophilic interaction liquid chromatography

A novel water-compatible molecularly imprinted SPE combined with zwitterionic hydrophilic interaction liquid chromatography method for selective extraction and determination of 3-methylflavone-8-carboxylic acid (MFA), the main active metabolite of flavoxate in human urine, was developed and validated. The effects of progenic solvents, pH, cross linker and amount of monomer were studied to optimize the efficiency and selectivity. The molecularly imprinted polymer showed good specific adsorption capacity with an optimum of 200 μmol/g at pH 7.5 and selective extraction of MFA from human urine. The recovery of MFA from human urine was >98%. The lower limit of quantification was 1.20 μg/mL. The proposed method overcomes the matrix effects of endogenous substances generally encountered during direct analysis of urine sample.     

Determination of sulfadiazine in eggs using molecularly imprinted solid‐phase extraction coupled with high‐performance liquid chromatography

The development of a simple and effective method for the isolation and purification of sulfadiazine residues in food of animal origin is of great significance since it is a great danger to human health. An off‐line molecularly imprinted solid‐phase extraction with high‐performance liquid chromatography method was proposed for the selective pretreatment and determination of sulfadiazine in eggs, rapidly and effectively. The molecularly imprinted polymer was proved to have a homogeneous spherical structure and porous surface morphology with excellent adsorption capacity of 5258 μg/g for sulfadiazine. The newly established method showed a good linearity in the range of 0–200 μg/L, low limits of detection (0.06 μg/L), acceptable reproducibility (RSD, 2.60–5.03%, n = 3), and satisfactory relative recoveries (78.22–86.10%). It was demonstrated that the proposed molecularly imprinted solid‐phase extraction with high‐performance liquid chromatography method could be applied to determine sulfadiazine in eggs, which simplified the pretreatment procedure and improved the accuracy of the analysis process by reducing the loss of sulfadiazine in the fat‐removing procedure compared with traditional methods. Molecularly imprinted solid‐phase extraction with excellent selectivity and adsorption capacity is a simple, rapid, selective, and effective pretreatment method for the determination of sulfadiazine in egg samples.     

Molecularly imprinted solid phase extraction for rapid screening of metformin

A molecularly imprinted solid phase extraction (MISPE) method has been developed for the rapid screening of metformin. Newly synthesized molecularly imprinted polymer (MIP) particles were slurry-packed into a micro-column for selective solid phase extraction (SPE) of metformin. With CH₃CN flowing at 0.5 ml/min, a total binding capacity of 1600 ng metformin was determined for the 20 mg of MIP particles. A broad range of MISPE conditions was evaluated with respect to sample solvent, pH, and buffer compositions. A 95±2% binding could be achieved from one 20-μl injection of sample solution in acetonitrile plus phosphate buffer, up to 1200 ng of metformin. However, the micro-column interacted indiscriminately with phenformin, a structural analogue, to attain 49±2% binding. Separation of phenformin from metformin was ultimately achieved, using differential pulsed elution (DPE) with 1 M trifluoromethacrylic acid in acetonitrile. Final pulsed elution (FPE) using 3% trifluoroacetic acid in methanol was good for the quantitative elution of metformin. The MISPE–DPE–FPE method, with UV detection at 240 nm, afforded a detection limit of 0.8 μg/ml (or 16 ng) for metformin. Each MISPE–DPE–FPE analysis required less than 5 min to complete.     

Molecularly imprinted polymer coating on metal‐organic frameworks for solid‐phase extraction of fluoroquinolones from water

In this work, a novel surface molecularly imprinted polymer with high adsorption capacity, high adsorption rate, and high selectivity for fluoroquinolones was prepared on the surface of UiO‐66‐NH₂, which is a kind of metal‐organic framework. The surface morphology and adsorption properties of this molecularly imprinted polymer were investigated. The maximum adsorption capacity was 99.19 mg/g, and adsorption equilibrium was achieved within 65 s. Combined with reversed‐phase high‐performance liquid chromatography, the molecularly imprinted polymer was used to selectively enrich, separate and analyze fluoroquinolones present in lake water. The results showed that the recoveries of the four fluoroquinolones were 92.6–100.5%, and the relative standard deviations were 2.9–6.4% (n = 3). The novel molecularly imprinted polymer is an excellent adsorbent and has broad application prospects in the enrichment and separation of trace analytes in complex samples.     

Synthesis of molecularly imprinted polypyrrole as an adsorbent for solid‐phase extraction of warfarin from human plasma and urine

The aim of this work was to develop a method for the clean‐up and preconcentration of warfarin from biological sample employing a new molecularly imprinted polymer (MIP) as a selective adsorbent for solid‐phase extraction (SPE). This MIP was synthesized using warfarin as a template, pyrrole as a functional monomer and vinyl triethoxysilane as a cross‐linker. The molar ratio of 1:4:20 (template–functional monomer–cross‐linker) showed the best results. Nonimprinted polymers (NIPs) were prepared and treated with the same method, but in the absence of warfarin. The prepared polymer was characterized by Fourier transmission infrared spectrometry and scanning electron microscopy. An adsorption process (SPE) for the removal of warfarin using the fabricated MIPs and NIPs was evaluated under various conditions. Effective parameters on warfarin extraction, for example, type and volume of elution solvent, pH of sample solution, breakthrough volume and maximum loading capacity, were studied. The limits of detection were in the range of 0.0035–0.0050 µg mL^?1. Linearity of the method was determined in the range of 0.0165–10.0000 µg mL^?1 for plasma and 0.0115–10.0000 µg mL^?1 for urine with coefficients of determination (R²) ranging from 0.9975 to 0.9985. The recoveries for plasma and urine samples were >95%. Copyright © 2015 John Wiley & Sons, Ltd.