球形片状微晶碱式碳酸镁的制备、表征及其用作纸填料的特性研究

以六水氯化镁和碳酸钠为原料,乙二醇为介质,采用直接沉淀法制备了碱式碳酸镁纳米粉体。分别用热重分析、X射线衍射、扫描电镜和红外对碱式碳酸镁纳米粉体进行了表征,通过分析确定了其组成和结构。用该法制备出的碱式碳酸镁纳米粉体的平均粒径为35.49nm,呈现球形且由片状微晶组成,分子式为4Mg CO3·Mg(OH)2·4H2O。以球形片状微晶碱式碳酸镁为添加剂制得的纸具有良好的吸水性、吸油性和阻燃性能。     

NASICON结构的锂离子导电微晶玻璃结构与电导率

通过对LixAlx-1Ge3-x(PO4)3(x=1.1～1.9)锂离子导电玻璃的差示量热扫描(DSC)数据,结合XRD及其Rietveld精修、FESEM和交流阻抗等测试方法,研究了该系微晶玻璃的物相组成、主晶相晶胞参数变化情况、微观结构形貌、锂离子电导率和电化学窗口等。结果表明:LixAlx-1Ge3-x(PO4)3(x=1.1～1.9)锂离子导电微晶玻璃析出导电主晶相为LiGe2(PO4)3。当x=1.5时,由于导电主晶相LiGe2(PO4)3晶粒充分长大、分布均匀,晶界清晰,LAGP导电微晶玻璃的室温电导率最高(可达5.3×10-4 S.cm-1),电化学窗口为7.2V,可以满足全固态锂离子电池对电解质高室温电导率和宽电化学窗口的应用要求。     

Li2O-Al2O3-GeO2-P2Os微晶玻璃的微观结构和离子电导率

采用传统熔体冷却法制备了Li3-xAl2-xGex(PO4)3(x=1.1～1.9)体系玻璃,并通过热处理工艺获得了高电导率的微晶玻璃.通过XRD、TEM和交流阻抗等测试方法,研究了该系微晶玻璃的物相组成、微观形貌和锂离子电导率.结果表明:该系统微晶玻璃析出导电主晶相为LiGe2(PO4)3,杂质相为AlPO4和GeO2.当x=1.5时,由于导电主晶相LiGe2(PO4)3晶粒充分长大、分布均匀,所制备微晶玻璃的室温锂离子电导率最高(5.72×10-4 S·cm-1),可以满足全固态锂离子电池对电解质高室温电导率的要求.     

Li2O-Al2O3-GeO2-P2O5微晶玻璃的微观结构和离子电导率

采用传统熔体冷却法制备了Li3-xAl2-xGex(PO4)3(x=1.1~1.9)体系玻璃,并通过热处理工艺获得了高电导率的微晶玻璃。通过XRD、TEM和交流阻抗等测试方法,研究了该系微晶玻璃的物相组成、微观形貌和锂离子电导率。结果表明:该系统微晶玻璃析出导电主晶相为LiGe2(PO4)3,杂质相为AlPO4和GeO2。当x=1.5时,由于导电主晶相LiGe2(PO4)3晶粒充分长大、分布均匀,所制备微晶玻璃的室温锂离子电导率最高(5.72×10-4 S.cm-1),可以满足全固态锂离子电池对电解质高室温电导率的要求。     

微晶酚酞分离富集分光光度法测定铊(Ⅲ)

建立了利用无毒的微晶酚酞作为固相萃取剂分离富集溶液中痕量Tl(Ⅲ)的方法。在H3PO4介质中,Tl(Ⅲ)在水相中与I-和结晶紫(CV+)形成离子缔合物而被微晶酚酞定量吸附,富集后的Tl(Ⅲ)可直接用光度法测定。控制一定的条件,Tl(Ⅲ)能与常见离子Na+,K+,Al3+,Cu2+,Pb2+,Zn2+,Ba2+,Mn2+,Ca2+,Cd2+,Fe2+等完全分离,且基本不受Cl-,Br-,SO42-,NO3-等阴离子的影响。方法可直接应用于环境水样中痕量Tl3+的测定,富集倍数可达100倍,回收率95.6%~101.8%,检出限为13 ng/L。     

苯甲基化木材溶液代替聚醚多元醇使用的研究

将苯甲基化木粉溶于四氢呋喃中 ,可以代替聚醚多元醇制备热固性材料 .以木材溶液的羟基值为指标 ,针对下层粘稠状物质 ,考察了不同溶液化条件对木材溶液活性羟基值的影响 ,并利用色质联用考察了苯甲基化木粉溶液化后上层清液中的组成 .实验证明 ,木材溶液能够代替聚醚多元醇使用的是下层的粘稠状物质 .同时实验结果表明 ,为了保证木材溶液制得的热固性材料具有足够的强度 ,溶液化时间应低于 6h ,液固比低于 6∶1.使用HCl与H3PO4 的混合酸比使用单一酸的催化效果更好     

H3PO4—BF3／ZrO2及H3PO4—BF3—H2SO4／ZrO2催化剂的酸性及结构研究

本文研究了固体酸烷基化反应催化剂H3PO4－BF3／ZrO2及H3PO4－BF3－H2SO4／ZrO2的酸性及其结构。用指示剂法及正丁胺滴定法测定了催化剂的酸强度及酸量；用吸附吡啶的红外光谱法研究了催化剂的表面酸类型；用FT－IR、XPS、XRD、DTA－TG及TPDE等方法研究了催化剂的结构。结果表明；两种催化剂表面均只有Broensted酸，酸强度为－8．2＜H0≤-5.6。H3PO4-BF3/ZrO2中，活性组分强能是以H2PO4^-：BF3的形态存在，BF3通过与H2O4^-的络合作用是催化剂的活性增强。H3PO4－BF3／ZrO2中，存在H2SO4与ZrO2的成盐作用，同时亦有可能存在H2SO4与H3PO4、BF3之间的相互作用。催化剂在下焙烧失活的主要原因是H2PO4^-失水生成P2O7^4－，使催化剂表面质子酸量大幅度降低所致。     

无机物离子对CuS微晶形态结构的有效调控

以CuCl2·3H2O,Cu（CH3COO）2·H2O和CuSO4·5H2O作为铜源,并向反应体系中引入少量NaCl或NaNO3,通过乙二醇溶剂中的溶剂热反应,合成了形貌各异的CuS微晶．结合XRD和SEM表征,初步探讨了阴离子Cl-、CH3COO-、SO4^2-和阳离子Na’对CuS微晶生长过程的影响．结果表明,Na＋对CuS微晶的生长过程没有显著影响,而Cl、CH3COO-、SO4^2-由于在{1012}晶面上选择性吸附能力的差异,显著影响CuS微晶的形貌．本研究为进一步有效调控CuS微晶的形貌及性能奠定了基础．     

水合硼氧酸盐结晶过程中液相的红外光谱

使用差示红外光谱的方法记录了MgB4O7.9H2O,NaB5O8.5H2O,MgB6O10.7H2O和MgB6O10.7.5H2O过饱和水溶液结晶析出相应固相时液相中多聚硼氧配阴离子的变化。结果得出,硼氧酸盐水溶液的红外光谱在800－1000cm^-1波数范围内,存在多种多聚硼氧配阴离子的特征峰,并对振动光谱频率进行了归属。870,810cm^-1为三硼氧配阴离子特征峰;844cm^-1为四硼氧配阴离子特征峰;929cm^-1为五硼氧配阴离子特征峰;959cm^-1为六硼氧配阴离子的特征峰。     

流动注射荧光猝灭法测定磷酸二氢盐

在pH=5.4的（CH2）6N4－HCl缓冲溶液中,建立Ce(Ⅲ）-NaCl-H2PO4-三元荧光熄灭体系,结合流动注射技术和荧光猝死定量数学模型Ln(F0/F)=LnKMF LnK3-LnKF Ln[M],考察Ce(Ⅲ）的阳离子型体测定H2PO4^-的可行性和适用性。实验表明：在20℃,pH=4.0-6.0时,Ce(Ⅲ)的阳离子型体与磷酸根反应,荧光猝灭程度显著;当注射泵转速为70r/min,样品测定速度为50h^-1,NaCl浓度为0．20－0．30mol/L时,H2PO4^-的测定线性浓度区间为0．20－1．80μg/mL,检测限LOD（3δ）=0．003μg/mL,样品回收率为97．3％－99．0％。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Selective syntheses of 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones via temperature-dependent Rh(II)-carbenoid-mediated 2H-azirine-ring expansion

The Rh(II)-catalyzed reaction of 2-carbonyl-substituted 2H-azirines with ethyl 2-cyano-2-diazoacetate or 2-diazo-3,3,3-trifluoropropionate provides an easy access to 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones. These compounds can be selectively prepared from the same starting material using temperature as the only varied parameter. The 2-azabuta-1,3-diene intermediate, a common precursor for both heterocyclic products, isomerizes into 2H-1,3-oxazine under kinetic control, while 1H-pyrrol-3(2H)-one is the sole product of the reaction at elevated temperatures. According to DFT-calculations a one-atom oxazine ring contraction involving ring-opening to a 2-azabuta-1,3-diene intermediate, followed by a 1,5- and 1,2-prototropic shift leads to the consecutive formation of imidoylketene and azomethine ylide, which then further undergo cyclization to the pyrrole derivative.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.