基于变形镜本征模式的空间光学遥感器波前误差校正方法研究

提出采用基于变形镜(DM)本征模式的自适应光学波前误差校正方法校正高分辨率空间光学遥感器的在轨波前误差。该方法利用变形镜各致动器的影响函数得到一组符合导数正交关系的变形镜本征模式,以图像功率谱密度在低频区域的积分和为评价函数,根据本征模式系数与评价函数之间的关系直接求解出各阶模式所需的校正量。利用实测的37单元变形镜的影响函数得到变形镜本征模式,基于该模式对泽尼克像差进行了开环和闭环仿真校正,定量分析了相位偏置和图像频率范围对算法精度的影响。针对遥感器主镜镜面热变形误差给出了仿真校正结果,分析了图像噪声和不同遥感图像对算法校正精度的影响。仿真结果表明基于变形镜本征模式的自适应光学校正方法可以有效校正波前误差,算法收敛速度快,对图像噪声和内容不敏感,适合用于空间光学遥感器的波前误差校正。     

校正低阶像差的9点促动变形镜——设计与实验

设计一有效口径为120mm的连续镜面、分立促动器的变形反射镜并进行了检测实验。以产生离焦、像散和彗差为目标,对变形镜的各项参数进行了优化,优化后的变形镜支撑有9个促动器和3个固定支撑点。固定点用于实现变形镜的定位,促动器用于镜面面形的控制。促动器采用了直线步进电机配合弹簧的结构,将电机的步进位移转换为力,在一定的线性范围内实现高精度的力促动。变形镜的检测设备采用了4D动态干涉仪,经响应函数的确定、校正力的求解和施加以及镜面再检测的步骤后,得到的实验结果表明变形镜能够产生高精度离焦、像散和彗差,且具有较大的动态范围。     

激光辐照下镀铬介质高吸收镜的热变形

为了分析激光辐照下反射镜热变形对光束质量的影响, 本文建立了激光光束45°角入射时镀铬介质高吸收镜的热固耦合模型, 对不同辐照光束下反射镜的热变形和镜体厚度对热变形的影响进行了分析, 并用哈特曼波前传感器对自由边界条件下的镜面热变形进行了检测。结果表明:吸收功率在0.085~0.185 W时, 镜面热变形随吸收功率的增加近似线性增加, 随辐照光斑的增加而减小;反射镜厚度在1~5 mm范围, 镜面热变形基本不变。在激光照射的初始阶段, 反射镜表面温度和热变形迅速增加, 在激光连续照射20 s后, 镜面温度增加量逐步变缓, 镜面热变形则在1 s以内就上升至0.27 μm, 之后变形量缓慢增加, 在100 s后达到相对稳定状态;关闭激光后, 镜面在120 s后恢复到初始状态。分析表明, 产生误差的因素主要为光斑大小和辐照光束入射角度。     

运用功能梯度结构降低大功率激光系统中镜面热变形的数值分析

 提出一种运用功能梯度结构以有效降低大功率激光系统中镜子温度和镜面热变形以及减缓热应力的新方法。讨论了环形分布和高斯分布2种类型的激光源。有限元分析结果表明，通过这种方法可使硅镜和铜镜的表面热变形成倍降低，并且还能同时显著降低镜体温度。讨论了代表热学和力学性质的函数表达式的斜率对镜面热变形的影响，研究表明：功能梯度结构的热物理对镜面形变产生重大影响，而力学性质对镜面形变的影响非常小。该结论可为具有该功能梯度结构的镜子优化设计和制造提供参考。     

热变形谐振腔的激光模式理论分析

应用微扰理论,对微热变形腔的激光模式进行了理论计算与分析;给出了激光模式之间的耦合以及等效光束发散角与镜面变形量之间的关系.结果表明镜面中心处热变形量越大,模式之间的耦合越强,激光腔模式发生畸变就越严重;当镜面中心处热变形量为0.5λ时,基模TEM0的中心光强将下降50%,其等效光束发散角将增大到镜面无变形时的2倍.     

温度对星载成像光谱仪谱线漂移的影响

为了研究温度对成像光谱仪谱线漂移的影响,分析了谱线漂移与光谱成像系统各镜面刚体位移之间的关系,建立了温度对成像光谱仪谱线漂移影响的理论模型,通过软件仿真和热光学试验对理论模型进行了验证和修正。基于线性光学理论建立了镜面刚体位移对谱线漂移影响的数学模型,使用蒙特卡罗法对理论模型进行了数值仿真验证;采用有限元法求解了温度载荷下各镜面的刚体位移,在Matlab软件环境下利用Code V的API函数对变形后的光学系统进行了光线追迹,求解了镜面刚体位移导致的谱线位置变化,研究了成像光谱仪的谱线漂移特性,得到了温度载荷作用下的谱线漂移模型;通过热光学试验对理论模型进行了验证和修正。结果表明,在8℃～28℃范围内,谱线在光谱方向仅发生整体平移,没拉伸或压缩效应;基于线弹性理论和线性光学模型建立的理论模型与试验结果吻合较好,最大偏差不超过12%,修正后的谱线漂移模型相对误差小于5%,绝对精度优于0.2pixel。     

热变形谐振腔的激光模式理论分析

 应用微扰理论,对微热变形腔的激光模式进行了理论计算与分析;给出了激光模式之间的耦合以及等效光束发散角与镜面变形量之间的关系。结果表明：镜面中心处热变形量越大,模式之间的耦合越强,激光腔模式发生畸变就越严重;当镜面中心处热变形量为0.5λ时,基模TEM₀的中心光强将下降50%,其等效光束发散角将增大到镜面无变形时的2倍。     

精密光束偏离装置棱镜组件的光机热分析

以精密光束偏离装置的棱镜组件为有限元模型,进行了光机热集成分析.对棱镜组件的结构强度进行了校核,分析了机械载荷作用下的镜面变形;通过模态分析,给出了装置的动态特性和镜面面形振动幅值的变化情况;最后对棱镜的热弹性变形进行了分析,对棱镜的光学性能进行了评价.结果表明：棱镜组件的最大变形在10 nm量级,最大应力为0.403 MPa,应力和应变相对于结构的准确度要求和材料的许用应力具有较大的裕度;前后棱镜组件的固有频率都大于550 Hz,装置具有良好的动态性能;通过对比棱镜在热-结构耦合分析和机械载荷下的分析结果,说明热效应对棱镜表面变形的影响远远大于机械载荷的影响.装置使用时必须采取严格的温控措施.     

空间望远镜分块式主镜建模与面形控制方法

空间望远镜分块式主镜的面形是由其背后布置的若干致动器控制的,是一个复杂的控制系统。应用BP神经网络的方法建立了以致动器作用力作为输入、镜面形变的Zernike多项式拟合系数作为输出的镜面形变模型。利用镜面有限元分析的大量数据对该模型进行了离线训练,并在最小二乘法的基础上,设计了加入单纯形修正算法的主镜面形静态控制器。仿真结果表明,应用该控制器对空间望远镜进行在线控制,控制精度优于最小二乘控制法。     

变宽度分割电极片状压电致动器的位移特性

针对硬磁盘驱动器中磁头定位两级伺服系统设计了一种新型压电致动器——悬臂梁式变宽度分割电极片状压电致动器.沿厚度方向极化的PZT压电陶瓷薄长片，宽度沿长度方向变化且沿长轴对称，一端固定一端自由构成悬臂梁.其上下两表面的电极均沿长轴分割成对称的两部分.施加电场使其中一半在d₃₁模式作用下伸长，而与其对称的另一半缩短，则压电片沿宽度方向产生弯曲，自由端便可产生致动位移.对该致动器的驱动电压-端部致动位移特性进行了理论分析、有限元模拟及实验验证.致动器中的电场诱导应力远小于陶瓷的抗张强度.致动器端部位移的测试结果略大于理论计算值.与现有磁头悬浮臂尺寸相近的致动器，在20—50V的电压驱动下均可获得1—2μm的致动位移.对25kTPI(track per inch)的高道密度硬磁盘，该位移已能覆盖至少一个磁道宽度，满足磁头定位两级伺服系统对第二级致动器致动位移的基本要求. 关键词：     

一种新的永久周期磁铁聚焦的高功率宽带放大器

提出了一种新的高功率宽带放大器，它由速调管和自由电子脉塞组成，用永久周期磁铁聚焦。研究了这种器件的电子束聚焦、群聚和辐射。在速调管提供一阶调制系数为30%，波导管的半径1.51cm，摇摆器的磁场振幅0.16T，周期7.92cm，电子束的电压490kV，电流50A和半径0.368cm的条件下，预估这种器件的辐射波频率为11.4GHz，输出辐射功率为18MW，输出辐射带宽为44%。     

Calibration and correction of lens distortion for two-dimensional digital speckle correlation measurement

Lens distortion practically presents in optical imaging system using in two-dimensional digital speckle correlation measurement (2D-DSCM) system, and gives rise to additional errors in the displacement and strain measurement. Camera calibration procedure is performed to obtain the coefficients of radial distortion and tangential distortion. The corrected displacement fields can be calculated using the distortion coefficient. The influence of distortion on displacement and strain measurement errors in experiment is further discussed. The three-point bending test result shows that the camera lens calibration method can effectively eliminate the effect of lens distortion and improve displacement and strain measurement accuracy.     

Performance of Dispersion-Compensated Optical Transmission Systems Based on Different Electrical Drivers

In this article, the simulation results have been presented for dispersive optical communication with different electrical drivers. The length of single-mode fiber has been put in a run that is compensated by dispersion-compensated fiber. The results have been presented and it is observed that of all the electrical drivers, the NRZ rectangular is best suited for dispersive optical communication systems. For this electrical driver, the parameters like BER remain constant and low. For other drivers, the BER decreases more for RZ super-Gaussian. Similarly, the Q factor increases with runs for all types of drivers except for NRZ rectangular, for which it decreases. For all the drivers, it is clear that as the runs are varied, the eye opening penalty increases, that is, there is less eye opening as the length of single-mode fiber is increased. It is also seen that the dispersion-compensated fiber compensates for the dispersion very effectively irrespective of the type of driver. Of the two formats, return to zero (RZ) and non-return to zero (NRZ), the earlier has more eye-opening penalty as the distortion is more and is clearly visible in all the rectangular, super-Gaussian, and raised cosine RZ formats. Of the three RZ formats, it is observed that RZ rectangular has the least eye-opening penalty. The non-return to zero format has less distortion and, of the two rectangular and raised cosine, the NRZ rectangular has less eye-opening penalty.     

Performance of Dispersion-Compensated Optical Transmission Systems Based on Different Electrical Drivers

In this article, the simulation results have been presented for dispersive optical communication with different electrical drivers. The length of single-mode fiber has been put in a run that is compensated by dispersion-compensated fiber. The results have been presented and it is observed that of all the electrical drivers, the NRZ rectangular is best suited for dispersive optical communication systems. For this electrical driver, the parameters like BER remain constant and low. For other drivers, the BER decreases more for RZ super-Gaussian. Similarly, the Q factor increases with runs for all types of drivers except for NRZ rectangular, for which it decreases. For all the drivers, it is clear that as the runs are varied, the eye opening penalty increases, that is, there is less eye opening as the length of single-mode fiber is increased. It is also seen that the dispersion-compensated fiber compensates for the dispersion very effectively irrespective of the type of driver. Of the two formats, return to zero (RZ) and non-return to zero (NRZ), the earlier has more eye-opening penalty as the distortion is more and is clearly visible in all the rectangular, super-Gaussian, and raised cosine RZ formats. Of the three RZ formats, it is observed that RZ rectangular has the least eye-opening penalty. The non-return to zero format has less distortion and, of the two rectangular and raised cosine, the NRZ rectangular has less eye-opening penalty.     

前向像移补偿下航空测绘相机畸变的纠正方法

为了提高航空测绘相机的制图精度,研究了前向像移补偿过程中测绘相机畸变的纠正方法。根据光学像差理论对畸变的影响因素进行了分析,得到了前向像移补偿过程中影响畸变的关键参数。考察了主点、主距等参数变化对畸变的影响规律,在此基础上提出前向像移补偿下畸变的计算模型。依据提出的模型对前向像移补偿下的航空测绘相机进行了数学仿真及外场飞行实验。结果表明,提出的算法稳定、有效,可以有效地纠正前向像移补偿时航空测绘相机的畸变,平面位置中误差较传统纠正方法可提高1.38倍。     

Elastic distortion of a conducting surface in the vicinity of a point charge

The elastic distortion of a conducting surface when a point charge is brought near the suface is investigated theoretically. The displacement field is calculated with the aid of a Green's function in terms of known functions. General results for surface and bulk displacements are displayed graphically. Numerical results for tungsten and aluminum are presented. Modifications of the image potential due to the distortion are discussed.     

变声速弹性沉积层下压缩波与剪切波的耦合影响

针对压缩波声速n²线性分布、剪切波声速平方线性分布的变参数弹性海底沉积层中声场建模问题,建立了关于压缩波与剪切波本征函数的偏微分耦合方程组,基于微扰法,通过逐次微分给出了本征函数的近似解析解.理论分析表明,只有剪切波声速平方的梯度不为零的情况下,沉积层中的压缩波才会与剪切波产生耦合.压缩波与剪切波耦合的影响会带来本征值的变化,其对近场声传播的影响较小,但远距离声传播损失的预报在考虑耦合后与实测数据符合得更好.此外,耦合还会导致沉积层中本征函数及其导数的变化,使得耦合与非耦合情况下沉积层中质点位移场不同.通过与商用声场软件COMSOL计算结果的对比分析检验了本文方法的正确性,且本文方法计算时间远小于COMSOL软件运行时间.     

声场中空化气泡的耦合振动及形状不稳定性的研究

计算了两个具有非球形扰动的气泡所组成系统的能量,并基于Lagrange方程得到了有声相互作用的非球形气泡的动力学方程和形状稳定性方程,研究了声场中非球形气泡间相互作用力对非球形气泡的形状不稳定性和气泡形状模态振幅的影响.研究结果表明声场中具有非球形扰动的气泡之间的耦合方式有两种:形状耦合模式和径向耦合模式,气泡之间的耦合方式取决于气泡形状扰动模态.由形状耦合及径向耦合产生的气泡之间的相互作用力能够改变单个气泡的形状不稳定及形状模态振幅,具体影响因素取决于声场驱动条件、气泡形状模态、相邻气泡的初始半径.     

On the interaction of an electron-hole drop with the crystal surface

Treating the crystal as an isotropic elastic continuum, we show that deformation-potential coupling should lead to a local, crater-type lattice distortion centered at the electron-hole-drop (EHD). Surface restraints on this displacement field generate attractive forces between the drop and the crystal surface. This result is discussed in connection with recent experiments on EHD-motion in Ge.     

What do electron and neutrino experiments tell us about nuclear effects in the deuteron?

We have performed an analysis of data from electron, neutrino and antineutrino scattering experiments on hydrogen and deuterium within the framework of the quark-parton model. The data indicate that the distortion of the structure functions of the neutrons and protons in the deuteron are small. This is in contrast with the observed distortion of the structure functions of nucleons bound in a heavy nucleus such as iron. These results support the hypothesis that the “EMC Effect” is related to the density of nucleons in a nucleus.