Mechanical properties of poly(vinyl methyl ether) hydrogels below and above their volume phase transition

The mechanical properties of radiation cross-linked poly(vinyl methyl ether) hydrogels below and above the volume phase transition (VPT) under isobar conditions were studied. The viscoelastic properties as a function of radiation dose, radiation source and polymer concentration at the state of irradiation were examined. Increased radiation doses led to higher cross-linking densities and higher moduli. Hydrogels irradiated with -rays were much harder than those obtained with electron beam irradiation at the same radiation dose. It was found that the modulus strongly increased by up to 1 order of magnitude at a temperature of the VPT of about 37 °C. In the collapsed state at temperatures well above the VPT a frequency dependence of the E() moduli in the range 0.1–22 Hz was detected, indicating viscoelastic behavior. To study the influence of solvent quality on the modulus of the hydrogels, rheological measurements were performed in water, 2-propanol and cyclohexane. A scaling exponent for the modulus according to de Gennes (G^2.25) was not found. Possible reasons for deviations (G^3.54) on poly(vinyl methyl ether) hydrogels were discussed in the context of deviations from ideal networks.     

Complexation of sodium 2-acrylamido-2-methylpropanesulfonate-monoethanolamine vinyl ether copolymer with polyelectrolytes in aqueous medium

A new water-soluble polyelectrolyte—the copolymer of sodium 2-acrylamido-2-methylpropanesulfonate and monoethanolamine vinyl ether—has been synthesized by free-radical copolymerization. The concentration behavior of the reduced viscosity of copolymer solutions that is typical for polyelectrolytes has been revealed. The reactivity ratios of the monomers have been measured. These values indicate a lower reactivity of monoethanolamine vinyl ether than that of sodium 2-acrylamido-2-methylpropanesulfonate. The complexation of this copolymer with poly(acrylic acid) and poly(N,N-dimethyl-N,N-diallylammonium chloride) has been studied. It has been found that the copolymer demonstrates the polyampholytic behavior and is able to form interpolymer complexes both with polycations and polyanions. It has been established that the polycomplex of the copolymer with polyacrylic acid has the unfolded structure due to the presence of sulfonate groups uninvolved in complexation, while the complex of the copolymer with poly(N,N-dimethyl-N,N-diallylammonium chloride) is compact owing to enhancement of hydrophobic interactions, and the sizes of its species are of the order of 80 nm.     

Synthesis and characterization of amphiphilic diblock copolymers of methyl tri(ethylene glycol) vinyl ether and isobutyl vinyl ether

Water-soluble diblock copolymers of methyl tri(ethylene glycol) vinyl ether (hydrophilic block) and isobutyl vinyl ether (hydrophobic block) of different molecular weights and composition were synthesized by living cationic polymerization. The molecular weight and comonomer composition of these copolymers were determined by GPC and ¹H NMR spectroscopy, respectively. Aqueous solutions of the copolymers were characterized in terms of their micellar behavior using dynamic light scattering, aqueous GPC, and dye solubilization. All the copolymers formed aggregates with the exception of a diblock copolymer with only two hydrophobic monomer units. The micellar hydrodynamic size scaled with the 0.61 power of the number of hydrophobic units, in good agreement with a theoretical exponent of 0.73. An increase in the length of the hydrophobic block at constant hydrophilic block length or an increase in the overall polymer size at constant block length ratio both resulted in lower critical micelle concentrations (cmcs). The cloud points of 1% w/w aqueous solutions of the polymers were determined by turbidimetry. An increase in the length of the hydrophobic block at constant hydrophilic block length caused a decrease in the cloud points of the copolymers. However, an increase in the overall polymer size at constant block length ratio led to an increase in the cloud point. © 1996 John Wiley & Sons, Inc.     

Effect of copolymer composition on interpolymer complex formation of (co)poly(vinyl ether)s with poly(acrylic acid) in aqueous and organic solutions

The complex formation between vinyl ether of poly(ethylene glycol‐co‐vinyl butyl ether) with poly(acrylic acid) has been considered in aqueous and isopropanol solutions. The effect of copolymer composition on the complex formation process was clarified. It has been shown that the incorporation of hydrophobic fragments into macromolecules enhances the hydrophobic stabilization of polycomplexes in aqueous solutions. In organic media this effect disappears. The stability of polycomplexes formed both in aqueous and in organic solutions in respect to the addition of dimethylformamide has been studied.     

Structure and swelling-release behaviour of poly(vinyl pyrrolidone) (PVP) and acrylic acid (AAc) copolymer hydrogels prepared by gamma irradiation

Copolymer network hydrogels were prepared by gamma irradiation of aqueous solutions of poly(vinyl pyrrolidone) (PVP) and acrylic acid monomer (AAc). The composition of the final hydrogels compared to the composition of the initial preparation solutions of hydrogels was determined. The chemical structure and nature of bonding was characterized by IR spectroscopy analysis, while the thermal durability of the prepared hydrogels was assessed by thermogravimetric analysis (TGA). The kinetic swelling in water and the pH-sensitivity of PVP/AAc copolymer hydrogels was studied. The drug release properties of PVP/AAc hydrogels taking methyl orange indicator as a drug model was investigated. The IR spectra indicate the formation of copolymer networks, whereas the TGA study showed that the PVP/AAc hydrogels possess higher thermal stability than pure PAAc and lower than PVP hydrogels. The kinetic swelling in water showed that all the hydrogels reached equilibrium after 24 h and that the degree of swelling increases with increasing the ratio of AAc in the initial feeding solutions. It was found that the degree of swelling of PVP/AAc hydrogels increases greatly within the pH range 4-7 depending on composition.     

Synthesis of methyldiethylsilylmethyl vinyl ether

Conclusions Methyldiethylsilylmethyl vinyl ether was synthesized by the reaction of the corresponding alcohol with acetaldehyde and hydrogen chloride, followed by the subsequent dehydrochlorination of the formed organosilicon -chloro ether.Translated from Izvestiya Akademii Nauk SSSR, Seriya Khimicheskaya, No. 5, pp. 1085–1086, May, 1971.     

Physical Hydrogels of Poly(vinyl alcohol) with Different Syndiotacticity Prepared in the Presence of Lactosilated Chitosan Derivatives

Poly(vinyl alcohol) (PVA) physical hydrogels were prepared by repeated freeze–thawing cycles using aqueous solutions of two PVA samples having different degrees of syndiotacticity, a‐PVA and s‐PVA with 55% and 61% of syndiotactic diads, respectively. The hydrogels were prepared in the presence of different amounts of lactosilated chitosan derivatives (LC) of different molecular weight. The PVA stereoregularity was found to have a dramatic effect on the amount of PVA incorporated into the hydrogels, leading to remarkable differences in the swelling degree and porosity of a‐PVA and s‐PVA hydrogels. A significant amount of LC was retained in the hydrogels after equilibrium swelling. The swelling of the a‐PVA hydrogels was found to increase significantly by increasing the amount of LC while it was only slightly increased in the case of s‐PVA hydrogels. The amount of LC released after equilibrium swelling was lower when chitosan derivatives with higher molecular weights were used. Increased initial concentrations of LC resulted in much higher porosity of the hydrogels. TGA and DSC studies showed that LC is stabilized by the incorporation in the PVA hydrogels. The melting temperature of the crystalline regions of PVA was not significantly influenced by LC. Conversely, the extension of the crystalline domains increased in the presence of LC. The retention of a chitosan derivative bearing β‐D ‐galactose side chain residues makes these hydrogels potentially useful as scaffolds for hepatocytes culture.

Scanning electron micrographs of PVA‐LC hydrogels: (a) a‐PVA; (b) a‐PVA/LC₁₅₀ 80:20; (c) a‐PVA/LC₁₅₀ 50:50.     

Complexation of hydrophobically modified polyelectrolytes with surfactants: anionic poly(maleic acid/octyl vinyl ether)/anionic sodium dodecyl sulfate

Interactions of surfactants with hydrophobically modified polyelectrolytes in aqueous solutions are important in several applications such as detergents, cosmetics, foods, and paints. Fundamental questions arise on the mechanisms of complexation of the polyelectrolyte and surfactant that control their behavior. In this work, the complexation was studied by examining interactions in aqueous solutions of a hydrophobically modified polymer, poly(maleic acid/octyl vinyl ether) (PMAOVE), with sodium dodecyl sulfate (SDS) by monitoring viscosity, pyrene solubility, light scattering, and analytical ultracentrifugation. When the anionic surfactant SDS was added to aqueous solutions of the similarly charged polymer PMAOVE, the surfactant was incorporated into the hydrophobic nanodomains of PMAOVE even far below the cmc of the surfactant. On the basis of viscosity, pyrene solubility, and analytical ultracentrifugation data, it is proposed that PMAOVE undergoes structural unfolding and at higher SDS concentrations mixed micelles are formed.     

Thermo‐ and pH‐sensitive amphiphilic gels of copolymers of vinyl ether of ethylene glycol

Novel thermo‐sensitive linear and crosslinked copolymers of vinyl ether of ethylene‐glycol and vinyl butyl ether have been synthesized by gamma‐irradiation copolymerization. The effect of comonomer hydrophobicity, neutral salts addition and nature of cations and anions on the position of lower critical soluble temperature of water‐soluble copolymers and swelling‐deswelling behavior of networks is demonstrated. The combination of thermosensitivity and pH sensitivity of hydrogels are realized in the case of crosslinked terpolymers. Copyright © 1999 John Wiley & Sons, Ltd.     

Temperature-responsive swelling and deswelling of the copolymers from vinyl ether of ethylene glycol and butyl vinyl ether

Linear and crosslinked copolymers of a vinyl ether of ethylene glycol (2-hydroxyethyl vinyl ether, ( 1 )) and butyl vinyl ether ( 2 ) are synthesized by α-irradiation polymerization. It is shown that the linear copolymers exhibit a phase separation phenomenon in dependence of the temperature due to the destruction of hydrogen bonds and the enhancement of hydrophobic interaction in aqueous solution. The processes of reversible swelling or shrinking upon temperature change are demonstrated for polymer networks.     

Relative thermodynamic stabilities of allyl vinyl and propenyl vinyl ethers

The relative thermodynamic stabilities of a number of isomeric allyl vinyl and propenyl vinyl ethers were determined by chemical equilibration in DMSO solution with KOBu-t as catalyst. From the temperature dependence of the values of the equilibrium constant the parameters G _m , H _m and S _m of isomerization at 298.15 K were evaluated. Propenyl vinyl ethers, owing to their low enthalpy contents, are much more stable than the isomeric allyl vinyl ethers. It appears that in the parent propenyl vinyl ether, the Me group attached to C- of the divinyl ether skeleton has a strong stabilizing effect, comparable to that of alkyl groups in ordinary olefins, on the unsaturated system. In more heavily alkyl-substituted divinyl ethers, however, the stabilizing effects of alkyl groups are less prominent, being comparable to the low stabilization energies of alkyl groups in vinyl ethers, and depend moreover, on the pattern of substitution.     

Thermosensitive poly(N-isopropylacrylamide-co-acrylamide) hydrogels: Synthesis, swelling and interaction with ionic surfactants

Thermosensitive hydrogels were prepared by free-radical polymerization in aqueous solution from N-isopropylacrylamide (NIPA) and acrylamide (AAm) monomers. N,N-Methylenebis(acrylamide) (MBAAm) was used as a crosslinker. A kinetic study of the absorption determined the transport mechanism. The diffusion coefficients of these hydrogels were calculated for the Fickian mechanism. It was shown that the swelling behavior of the P(NIPA-co-AAm) hydrogels can be controlled by changing the amount of MBAAm. The swelling equilibrium of the P(NIPA-co-AAm) hydrogels was also investigated as a function of temperature in aqueous solutions of the anionic surfactant sodium dodecyl sulfate (SDS) and the cationic surfactant dodecyltrimethylammonium bromide (DTAB). In SDS and DTAB solutions, the equilibrium swelling ratio of the hydrogels increased, this is ascribed to the conversion of non-ionic P(NIPA-co-AAm) hydrogel into polyelectrolyte hydrogels due to binding of surfactant molecules through the hydrophobic interaction. Additionally, the amount of free SDS and DTAB ions was measured at different temperatures by a conductometric method, it was found that the electric conductivity of the P(NIPA-co-AAm)—surfactant systems depended strongly on both the type and concentration of surfactant solutions.     

The effect of solvents on asymmetric induction cationic copolymerization of l-menthyl vinyl ether with indene

Cationic copolymerization of l-menthyl vinyl ether (l-MVE) with indene (IN) was carried out in several solvents with BF₃OEt₂ as catalyst at 0°C. The solvents used in this study were selected toluene (Tol), chloroform (CHCl₃), chlorobenzene (BzCl), 1,2-dichloroethane (EtCl₂), and nitrobenzene; (BzNO₂)/Tol = 65/35 mixture solvent. l-Methyl residue, which is an optically active side chain of copolymer produced by cationic copolymerization, was removed with dry hydrogen bromide gas by ether cleavage reaction. The copolymer [vinyl alcohol(VA)–lN], produced by the ether cleavage reaction, also showed optical rotation. From this result, therefore, it was concluded that asymmetric induction takes place in the copolymer main chain. The efficiency of asymmetric induction was determined by the measurement of optical rotation of VA–IN copolymer after the ether cleavage reaction. The efficiency of asymmetric induction in the copolymer main chain developed from the variation on polymerization solvents; the order was Tol > EtCl₂ > BzCl > CHCl₃ > BzNO₂/Tol (65/35) mixture solvent.     

Temperature-sensitive poly(vinyl methyl ether) hydrogel beads

Temperature-sensitive hydrogel beads were prepared by radiation crosslinking of poly(vinyl methyl ether) PVME spheres wrapped in Ca-alginate. The obtained gel beads have diameters in the sub-millimeter or millimeter range (depending on the PVME concentration). They were characterized by sol-gel analysis, swelling measurements, and differential scanning calorimetry. The gel content g increases with increasing radiation dose D. The swelling degree Q_v decreases with increasing PVME concentration c_p and increasing D. In comparison to PVME bulkgels the phase-transition temperature of the synthesized PVME gel beads is a little decreased.     

New polymer structures based on vinyl ether polymerization

Sequential living cationic polymerization of octadecyl vinyl ether (ODVE) and methyl vinyl ether (MVE) was used for the preparation of amphiphilic ABA‐type block copolymers. The polymerization of ODVE was initiated with the trimethyl silyl iodide/1,1,3,3‐tetramethoxy propane/ZnI₂ system at 0°C in toluene. The living bifunctional polyODVE thus obtained was used as initiator for the polymerization of MVE. Below the LCST of polyMVE (37°C), the copolymers are amphiphiles. Above the LCST of polyMVE, the polyMVE‐blocks become hydrophobic and the amphiphilic nature of the block copolymer is lost. This was demonstrated by using the block copolymers as emulsifiers for water/decane mixtures. The emulsions were stable for several hours at room temperature, while the emulsion stability decreased to about 30 seconds at 40°C. PolyMVE‐α,ω‐bis‐methacrylates were obtained by end‐capping of living bifunctional polyMVE with 2‐hydroxyethyl methacrylate (HEMA). Copolymerization of these bis‐macromers with HEMA leads to segmented networks. The networks showed a reversible swelling/deswelling behavior in water as a function of temperature. This is caused by a change of the hydrophilicity of the polyMVE segments in the networks. Hexa(chloromethyl)melamine, combined with zinc chloride was found to be an efficient hexafunctional initiator for the living cationic polymerization of vinyl ethers. This simple initiating system opens new ways for the synthesis of endgroup‐functionalized star‐shaped poly(vinyl ethers).     

Properties of low temperature swelling hydrogels prepared with partially saponified PVA and drug release using the hydrogels

The hydrogels prepared by the crosslinking of partially saponified poly(vinyl alcohol) (PVA) which has low critical solution temperature (LCST) in water showed characteristics of swelling at low temperature and shrinkage at high temperature. The hydrogels showed repeatable swelling–shrinking behavior. The hydrogels containing release substances such as cyanocobalamin, p‐acetamidophenol, insulin and ovalbumin were prepared by dipping these aqueous solutions and the release substances were studied. Insulin and ovalbumin were not absorbed by the hydrogels when the use of partially PVA with the degrees of polymerization (DPs) of 540 were prepared, but absorbed by the hydrogels with DPs of 1860. The size of the polymer network prepared with a higher DP was suitable for the absorption of insulin and ovalbumin. In accordance with release substances, the release patterns were different. In this way, the polymer network sizes and their swelling behaviors of partially saponified PVAs were estimated. Copyright © 2003 John Wiley & Sons, Ltd.     

Studies on propagating species in cationic polymerization of styrene derivatives by acetyl perchlorate or iodine. II. Salt effect on the relative reactivity in the cationic copolymerization of styrene derivatives with 2-chloroethyl vinyl ether initiated by iodine

To determine the effect of the dissociation of propagating species on the relative reactivity of monomers, 2-chloroethyl vinyl ether was copolymerized with p-methoxystyrene or with p-methylstyrene by using iodine in various solvents at 0°C. A common-ion salt (tetra-n-butylammonium iodide or tetra-n-butylammonium triiodide) was added to these copolymerization systems in a polar solvent to depress the dissociation of the propagating species. The addition of a common-ion salt increased the vinyl ether content in the copolymer. The more the dissociation of propagating species was depressed, the more the vinyl ether content in the copolymer increased. This effect of common-ion salt was in agreement with that of decreasing solvent polarity which yielded vinyl ether-rich copolymer as well. Therefore, the change of the monomer reactivity ratio by the solvent polarity, which used to be explained in terms of a selective solvation, must be reconsidered from the viewpoint of varying degrees of the dissociation of propagating species.     

Polymerization of vinyl acetate in fatty acids and properties of poly (vinyl alcohols) derived from the poly (vinyl acetates)

Polymerization of vinyl acetate (VAc) in various fatty acids (carbon numbers 4–18) was carried out. Chain transfer constants to the acids were determined to be 20–35×10^–4, from which the constant to a methylene group was obtained to be 0.73×10^–4. Viscometry in aqueous solution of derived poly (vinyl alcohol) (PVA) showed the usual behavior in terms of Huggins constant obtained by the Schulz–Blaschkes equation for PVAs derived from fatty acid systems lower than hexadecanoic acid. PVA derived from octadecanoic acid system showed abnormality, indicating association of alkyl groups. Contact angles on surfaces of PVAs cast from aqueous solutions were measured. While those of PVA derived from lower acid systems were 62°, those of PVAs derived from higher aids were higher and increased to 92° with increase in carbon number to octadecanoic acid. Alkyl groups in the PVAs were estimated to appear on the surfaces. Surface tension of aqueous solution of the PVA derived from octadecanoic acid showed high surface activity, and depended on pH of the solution, indicating the presence and cleavage of lactone ring at the combined portion between PVA and the acid.     

Asymmetric induction copolymerization of optically active l-menthyl vinyl ether with styrene and N-phenylmaleimide

The copolymerizations of l-menthyl vinyl ether (l-MVE) with styrene (St) and N-phenylmaleimide (N-PMI) as comonomers were carried out in benzene with azobisisobutyronitrile (AIBN) as an initiator to give optically active copolymers. After the removal of the optically active menthyl group by use of hydrogen bromide gas, the ether-cloven l-MVE-N-PMI copolymer (VA-N-PMI) was still optically active. On the other hand, the optical activity of l-MVE-St copolymer disappeared after ether cleavage. It is thought that asymmetric induction took place in the polymer main chains. The optical rotatory dispersion and circular dichroism of the original and ether-cloven copolymers were measured in order to confirm the asymmetric induction.     

Stereoregularity of poly(vinyl ether)

α-Methylvinyl isobutyl and methyl ethers were polymerized cationically and the structure of the polymers was studied by NMR. Poly(α-methylvinyl methyl ether) polymerized with iodine or ferric chloride as catalyst was found to be almost atactic, whereas poly(α-methylvinyl isobutyl ether) polymerized in toluene with BF₃OEt₂ or AlEt₂Cl as catalyst was found to be isotactic. In both cases, the addition of polar solvent resulted in the increase of syndiotactic structure as is the case with polymerization of alkyl vinyl ether. tert-Butyl vinyl ether was polymerized, and the polymer was converted into poly(vinyl acetate), the structure of which was studied by NMR. A nearly linear relationship between the optical density ratio D₇₂₂/D₇₃₆ in poly(tert-butyl vinyl ether) and the isotacticity of the converted poly(vinyl acetate) was observed.