Current-density imaging using ultra-low-field MRI with adiabatic pulses

Magnetic resonance imaging (MRI) allows measurement of electric current density in an object. The measurement is based on observing how the magnetic field of the current density affects the associated spins. However, as high-field MRI is sensitive to static magnetic field variations of only the field component along the main field direction, object rotations are typically needed to image three-dimensional current densities. Ultra-low-field (ULF) MRI, on the other hand, with B₀ on the order of 10–100 μT, allows novel MRI sequences. We present a rotation-free method for imaging static magnetic fields and current densities using ULF MRI. The method utilizes prepolarization pulses with adiabatic switch-off ramps. The technique is designed to reveal complete field and current-density information without the need to rotate the object. The method may find applications, e.g., in conductivity imaging. We present simulation results showing the feasibility of the sequence.     

Evaluation of critical current based on a new transition concept

The critical current of high-temperature superconductor (HTS) tapes depends on temperature, magnetic field, and flux angle against the tape. Analyzing the performance of an HTS coil relies on the critical current equation, which has these dependencies. To date, the critical current equation has been obtained by fitting the measured data. However, this fitting method requires the time-consuming and laborious work of measuring the tapes. In this study, based on a new transition concept in applying a magnetic field, we show how to obtain the critical current equation, while keeping the temperature constant. From the wave function of the Cooper pair which distributes along a magnetic flux quantum, a wave function at the transition state is obtained; this yields the wave functions with perpendicular and parallel magnetic components against the tape. Combining these wave functions yields the conclusive critical current density equation. To confirm the accuracy of this equation, used Bi-2223/Ag tapes, it was compared with the measured critical current under various magnetic fields and flux angles; it was found that they agree well. The parameters of this equation can be obtained by measuring the perpendicular/parallel critical magnetic field component. This equation does not require fitting the measured data, therefore, it can be employed with any Bi-2223/Ag tape.     

基于永磁恒定磁场激励的起始磁化曲线测量

现有起始磁化曲线测量系统需绕制励磁线圈和感应线圈,在线应用受限.为此,本文提出了一种基于永磁恒定磁场激励的起始磁化曲线测量原理并搭建了相应测量系统.该系统采用永磁磁化器作为激励磁源,以对称磁化方法在圆柱棒状构件上激励出随轴向位置变化的恒定磁场作为激励磁场;采用阵列霍尔探头测量构件表面不同提离下的轴向和法向磁感应强度;并基于多项式外推法和磁场高斯定理外推法,推算构件与空气分界面上的轴向和法向磁感应强度;进一步地,根据分界面上的磁感应强度获取构件的起始磁化曲线.系统测量结果表明,在永磁恒定磁场激励下,无须励磁线圈和感应线圈即可方便地获取棒状构件的起始磁化曲线,测量误差小于10%,测量误差标准差小于0.01,重复性较好.该系统可为便捷地在线测量棒状构件起始磁化曲线提供新途径.     

一种永磁磁共振中磁体涡流场的测量方法

磁共振成像（Magntic Resonance Imaging,MRI）技术是一种先进的医疗影像技术.在MRI系统中,通过梯度线圈电流快速切换方向,对待测区域施加梯度磁场,产生的梯度磁场会在其周围的金属体内激发出变化的涡旋电场,进而导致金属体内闭合的回路中产生对原来的梯度电流起抑制作用的感生电流,也就是我们所说的涡流.本文介绍了一种测量磁体涡流场的方法,结合电磁感应定律,设计了一种磁体涡流场测量装置,通过硬件采集以及软件处理的方法,将理想梯度场与实际磁场进行相减并将波形实时呈现,实验结果表明该方法可实现对磁体涡流场的测量.     

Current-density imaging using ultra-low-field MRI with zero-field encoding

Electric current density can be measured noninvasively with magnetic resonance imaging (MRI). Determining all three components of the current density, however, requires physical rotation of the sample or current injection from several directions when done with conventional methods. However, the emerging technology of ultra-low-field (ULF) MRI, in which the signal encoding and acquisition is conducted at a microtesla-range magnetic field, offers new possibilities. The low applied magnetic fields can even be switched off completely within the pulse sequence, increasing the flexibility of the available sequences. In this article, we present a ULF-MRI sequence designed for obtaining all three components of a current-density pattern without the need of sample rotations. The sequence consists of three steps: prepolarization of the sample, signal encoding in the current-density-associated magnetic field without applying any MRI fields, and spatial encoding in a microtesla-range field using any standard ULF-MRI sequence. The performance of the method is evaluated by numerical simulations. The method may find applications, e.g., in noninvasive conductivity imaging of tissue.     

Analysis of the magnetic field distribution and estimation of the critical current density based on a magnetooptical study of the superconducting strip composites

The results of magnetic flux penetration into high-temperature superconducting composites of the second generation have been analyzed and described. The distribution of magnetic flux was observed experimentally using the magnetooptical visualization technique at various temperatures of 4.2–80 K. The experimental data have been found to coincide with the results of analytical and semi-numeric calculations of magnetic field profiles carried out for regimes of full and partial field penetration into superconducting composites. The method of estimating the critical current density based on measurements of the topography of the transverse magnetic flux has been considered, and an approach to estimating the critical current density for strips from measurements of the tangential field component has been proposed.     

In vivo detection of applied electric currents by magnetic resonance imaging

Magnetic resonance imaging is very sensitive to magnetic field variations. This inherent sensitivity can be exploited to measure small electric currents flowing in the human body. This report describes an experiment in which the magnetic fields produced by small currents applied to the forearm of a living subject have been detected in the tissue. It shows how such measurements have been used to measure current density. The suggested technique is used to measure one component of a current density in a saline solution in vitro.     

Bi-2223/Ag高温超导带临界电流各向异性的实验测量及分析

本文介绍了Bi-2223/Ag高温超导带临界电流各向异性的实验测量方法及原理,指出了在不同磁场方向(与超导带面夹角)下,Bi-2223/Ag带临界电流随直流背景磁场的变化规律以及实验应注意的问题.Bi-2223/Ag带材的各向异性决定了其临界电流对垂直于带材表面的磁场非常敏感,这是该带材在高温超导磁体等强电应用方面的不利因素.     

Measurement of azimuthal magnetic fields in a Z-pinch gas discharge using the faraday rotation of a probe beam

The Faraday rotation of the plane of polarisation of a probe beam by azimuthal magnetic fields in the presence of beam deflection caused by refractive index gradients is discussed for a plasma carrying an axial current. A method for calculation of the magnetic field profile from experimental data is described. Bθ can be found by Abel inversion if the electron density is known and if deflected rays can be collected by an optical system and focussed onto a detector. Typical Faraday rotations calculated for the Bennett pinch assuming small beam deflection are found to be proportional to the plasma current and to the angle of deflection. If the probe beam wavelength is chosen to satisfy the approximate relation N₀λ² ≈ 3.5 × 10¹³ m^-1, where N₀ is the electron density on the axis, measurement of Bθ with beam deflections less than 2 × 10^-2 radians should be possible in cases where small rotations can be detected in the mid-to-far infra-red part of the spectrum.     

大电流超导材料临界电流的感应法测量

文中总结了感应法测量大电流超导材料临界电流的方法 ,叙述测量的原理及装置 ,分析对环电流进行定标时可能产生的误差及减少误差的措施 ,给出计算结果 ,并对之进行讨论     

带集磁器的吸引式电磁力小管件翻边方法

针对微小铝合金管件电磁翻边工艺,现有方法将驱动线圈置于管件端部外侧,利用双频电流法产生吸引式电磁力实现翻边。然而其翻边能力不强,基于此提出一种带集磁器的吸引式电磁力翻边方法。在现有方法基础上引入集磁器,利用其能够改变磁场位形的特点,优化电磁力分布并增大轴向电磁力,达到增强翻边效果的目的。为验证该方法的可行性,通过搭建管件翻边过程的电磁-结构全耦合有限元仿真模型,对比引入不同集磁器后的翻边效果,同时分析了不同工况对电磁力分布、电磁力密度以及磁场和涡流的影响。得出阶梯型集磁器效果最佳,结果表明,该方法下管件翻边角度从38°增大到90°。进一步分析表明,其磁通密度径向分量和涡流密度环向分量分别增大到164%和135%,作用在管件上的电磁力分布改变,峰值时刻轴向电磁力体密度明显加强,增大到211%。该方法进一步完善了对微小铝合金管件的电磁翻边成形,对拓展电磁成形技术在铝合金管件翻边上的应用具有一定意义。     

磁电耦合超材料本构矩阵获取方法的研究

单负(仅介电常数或仅磁导率小于零)超材料以及由导线-开口谐振环组成的双负超材料本构参数的提取通常采用传统的S参数方法. 由于磁电耦合超材料存在交叉极化现象, 仅用介电常数和磁导率两个本构参数无法准确描述其电磁特性. 传统的S参数提取方法一开始就假定超材料仅具有介电常数和磁导率两个本构参数, 所以采用该方法提取磁电耦合超材料本构参数存在明显局限性. 将磁电耦合超材料中的电元件和磁元件分别等效为面电流和面磁流, 通过推导平均电通密度和磁通密度与外加电磁场的相互关系, 从理论上获取了磁电耦合超材料2×2 的本构参数矩阵, 确定了磁电耦合超材料这四个本构参数与磁元件的磁导率、电元件的介电常数、空间色散项和耦合系数之间的关系解析公式, 进而获得了折射率理论计算公式. 利用该折射率公式对折射率提取值进行了非线性拟合, 发现提取值和理论值之间的误差很小, 这个结果很好地验证了所给出的本构矩阵解析式和折射率公式的正确性. 根据拟合结果, 获得了磁电耦合超材料本构矩阵中四个电磁参数的频率响应曲线. 所提出的磁电耦合超材料本构矩阵参数获取方法将为研究磁电超材料中电元件和磁元件的耦合现象提供重要的理论参考.     

Sensing domain wall pinning in the longitudinal magnetoresistance of a two-dimensional electron gas

We investigate the sensing of domain wall pinning in thin Co wires positioned on top of a two-dimensional electron gas (2DEG) heterostructure by measuring the longitudinal resistance of the 2DEG as the magnetic field is swept, in an analogy to the Barkhausen effect. For comparison, we also measure the magnetoresistance of the ferromagnetic film in the same device in a subsequent sweep. Compared to the Hall measurements, the longitudinal measurement has the advantage of sensing magnetic activity over longer lengths, while compared to the measurement of the magnetoresistance in the ferromagnetic wire, it offers complementary information related to the pinning and unpinning of the domain wall, due to its sensitivity only to the out-of-plane magnetic field component.     

Current Structures with Magnetic Shear in Space Plasma

Observations of current structures with magnetic shear by the Cluster satellite quartet in the magnetotail and the Wind satellite in the solar wind have been reported. In current structures with magnetic shear, the following structural features have been identified: (i) thickening of a current layer, (ii) plasma density distribution asymmetric with respect to the layer plane, and (iii) formation of an asymmetric current density profile. The kinetic features of the dynamics of ions in current layers with initial shear deformation have been considered. A mechanism has been proposed for the formation of self-consistent current sheets with a nonzero shear magnetic field component.     

测量条件对掺锡氧化铟薄膜电学测量结果的影响

用van der Pauw方法测量磁控溅射制备的掺锡氧化铟(ITO)薄膜的电学性能,研究了在室温和冰水混合条件下测量电流大小对电阻率测量结果的影响;在室温条件下测量电流和磁场的大小对载流子浓度和迁移率测量结果的影响.实验结果显示,测量电流为5 mA和测量磁场为0.5 T时,测量结果最佳.     

Excitation of spin remagnetization waves in systems with spin-orbit coupling

Elementary excitations of a new type in paramagnetic materials with spin-orbit interaction are predicted theoretically within the Rashba model and named the spin remagnetization waves. These normal modes arise from rotation of the spin magnetic moment in a medium where the electric field contains a constant component and a traveling wave component. A method is proposed for exciting these vibrations by illuminating the sample with an oscillating interference pattern. The spin remagnetization waves can be experimentally detected by measuring the dependence of the current through the sample on the oscillation frequency and wave vector of the interference pattern.     

Density-induced interchange of anisotropy axes at half-filled high Landau levels

We observe density-induced 90 degrees rotations of the anisotropy axes in transport measurements at half-filled high Landau levels in the two dimensional electron system, where stripe states are proposed ( nu = 9/2, 11/2, etc.). Using a field effect transistor, we find the transition density to be 2.9x10(11) cm(-2) at nu = 9/2. Hysteresis is observed in the vicinity of the transition. We construct a phase boundary in the filling factor magnetic field plane in the regime 4.4相似文献   

Auxiliary phase encoding in multi spin-echo sequences: application to rapid current density imaging

Multi spin-echo sequences such as single-shot RARE are very sensitive to the initial phase of the transverse magnetization, and they can preserve only the transverse magnetization component which is aligned with the axis of the refocusing pulse rotation. Therefore, two separate single-shot RARE experiments with phases of refocusing pulses 90 degrees apart have to be run and their complex images summed to obtain an error-free phase map of the initial transverse magnetization. This is particularly useful when auxiliary phase encoding is integrated in the preparation period of the RARE sequence, such as when encoding flow, displacement, susceptibility, pH or temperature. In this paper, the two-shot RARE approach is verified first theoretically and then experimentally by demonstrating its application to rapid current density imaging (CDI). The sequence consists of the preparation period which triggers electric pulses in the sample followed by the RARE acquisition period. Electric currents through the sample induce a magnetic field change in the direction of the static magnetic field and a phase change of the initial magnetization proportional to it. To calculate one component of current density two orthogonal components of magnetic field change must be measured. In general, for 2D non-symmetrical samples, this can be done by rotating the sample to a perpendicular orientation. The proposed CDI method allows much for faster magnetic field change mapping than the standard spin-echo based CDI.     

Residual field suppression for magnetocardiography measurement inside a thin magnetically shielded room using bi-planar coil

For a magnetocardiography (MCG) system inside a magnetically shielded room (MSR), the residual field should be further suppressed to obtain high-quality MCG signals. In this paper, a compensation system has been developed based on the bi-planar coil and the proportional-integral-derivative (PID) controller. The bi-planar coil, derived from the target-field theory and the Tikhonov regularization method, is utilized to generate magnetic field with high uniformity in the pre-defined target region. And the PID controller is introduced to provide dynamic compensation current for the coil, according to the residual field change monitored by a reference SQUID magnetometer. The measurement results show that the noise suppression ratio (NSR) can reach above 20 dB in the low-frequency range from 0.1 Hz to 50 Hz. The DC component and the fluctuation of the residual field in time-domain can be respectively suppressed to 0 pT and 4 pT, indicating that this proposed compensation method is useful for the MCG measurement.     

Measurements, characteristics, and origin of new electromagnetic interference on magnetocardiographic measurements

In order to eliminate the influence of the large-amplitude magnetic field noise that has complicated magnetocardio-graphic studies since October 2009, we have performed high-accuracy measurement of the environmental magnetic field noise in the vicinity of Beijing Subway Line 4 using a three-component height T c radio frequency (rf) superconducting quantum interference device (SQUID). By analysing the spatial form and other characteristics of the time and the frequency domains and by calculating the circumferential magnetic field distribution based on a duel-end feeding system model, we reach the following conclusions: (i) the main source of magnetic field noise is the magnetic field generated by the subway trains, and (ii) the magnetic field interference results mainly from the imbalance between traction current and return rail current that is caused by the leakage current.