Fluorinated α-Diimine Nickel Mediated Ethylene (Co)Polymerization

Fluorine substituents in transition metal catalysts are of great importance in olefin polymerization catalysis; however, the comprehensive effect of fluorine substituents is elusive in seminal late transition metal α-diimine catalytic system. In this contribution, fluorine substituents at various positions (ortho-, meta-, and para-F) and with different numbers (F_n; n=0, 1, 2, 3, 5) were installed into the well-defined N-terphenyl amine and thus were studied for the first time in the nickel α-diimine promoted ethylene polymerization and copolymerization with polar monomers. The position of the fluorine substituent was particularly crucial in these polymerization reactions in terms of catalytic activity, polymer molecular weight, branching density, and incorporation of polar monomer, and thus a picture on the fluorine effect was given. As a notable result, the ortho-F substituted α-diimine nickel catalyst produced highly linear polyethylenes with an extremely high molecular weight (M_w=8703 kDa) and a significantly low degree of branching of 1.4/1000 C; however, the meta-F and/or para-F substituted α-diimine nickel catalysts generated highly branched (up to 80.2/1000 C) polyethylenes with significantly low molecular weights (M_w=20-50 kDa).     

A New Type of Polymer-Supported Metallocene Catalyst for Ethylene Polymerization

Although homogeneous metallocene catalysts show some specific characteristics, such as single site, extremely high catalytic activity, high ability to incorporate monomers, narrow molecular weight and comonomer distribution, and excellent control of stereoregularity, but they also suffer some drawbacks, a very large amount of MAO requirement, inability to be used in slurry or gas phase processes, and poor control of polymer morphology. Therefore, it is necessary to modify the catalysts for the…     

Characteristics of Titanocene Catalyst Supported on Palygorskite for Ethylene Polymerization

Due to the technical problems observed for homogeneous metallocene catalysts, such as reactor fouling and requirement for large amount of expensive methylaluminoxane (MAO) as cocatalyst, the development of supported metallocene catalysts is very important…     

Ligand Steric Effects on Naphthyl-α-diimine Nickel Catalyzed α-Olefin Polymerization

Naphthyl-α-diimine nickel complexes with systematically varied ligand sterics, activated by modified methylaluminoxane(MMAO), were tested in the polymerization of higher α-olefin(1-hexene, 1-decene and 1-hexadecene) under suitable conditions. The polymerization results indicated the possibility of precise microstructure control, depending on catalyst structure, polymerization temperature, monomer concentration and types of monomers, which in turn strongly affects the resultant polymer properties. Naphthyl-α-diimine nickel complex bearing chiral bulky sec-phenethyl groups in the o-naphthyl position showed good catalytic activity, and resulted in branched polymers(42-88/1000 C) with high molecular weights(M_n:(4.3-15.2) × 10~4 g·mol~(-1)) and narrow molecular weight distribution(M_w/M_n = 1.13-1.29, RT), which suggested a living polymerization. The increasing steric hindrance of catalyst leads to enhance insertion for 2,1-insertion of α-olefin and the chain-walking reaction.     

Palladium-Catalyzed Selective α-Arylation of ortho-Bromoacetophenones

Synthesis of 1-(2-bromophenyl)-2-phenylethanones via an intermolecular Pd-catalyzed α-arylation of 1-(2-bromophenyl)ethanones is presented. The method relies on selective C-H activation (α-arylation) of relatively more reactive external iodo-arenes as coupling partners without affecting the bromo-substituent. Moreover, the scope and generality of the method has been well studied by employing the reaction with iodo-arenes as coupling partners bearing electron-withdrawing, simple, and electron-donating groups on the aromatic ring.     

Nickel(Ⅱ) a-Diimine Catalysts with Carboxyl Groups for Ethylene Oligomerization and Polymerization

A series of nickel(II) ?-diimine complexes with strong electron-withdrawing carboxyl groups, having reactive hydrogen atoms, were prepared and used as precatalysts for ethylene oligomerization and/or polymerization. The influence of metal halides and ligand structure on the catalytic activity and properties of products was investigated. The results showed that nickel bromide was much more active than nickel chloride, and the substituents at the ortho-position of aryl ring had large influence on the properties of products. Therefore, the products ranging from liquid oligomers to polymers could be readily obtained by the variation of the substituents on the ligands and reaction conditions.     

Organomagnesium Compounds as Promoters for Increasing the Catalytic Efficiency in the Polymerization of Ethylene

It wasstudied that organomagnesium compounds can promote the catalytic efficiencyof catalysts of Ti system with MgCl2 as the carrier for polymerization of ethylene.     

A Detailed Polymerization Model for Cerenol® Polyols

Summary: A mathematical model of the acid catalyzed 1,3-propanediol polymerization has been developed. Two catalysts investigated include sulfuric acid and superacid (tetrafluoroethane sulfonic acid or triflic acid). Based on a detailed reaction mechanism, population and mass balance equations have been derived for small molecules as well as for polymeric species of numerous chain distributions, which are distinguishable in terms of protonation state and end group functionality. Due to the interaction of the sulfuric acid catalyst with the polymer ends, a novel, dual index polymer chain distribution was derived and implemented. The model has been validated with various sets of experimental data obtained in a lab-scale reactor setup. Dynamic model outputs such as monomer concentration, molecular weight averages, unsaturated and sulfate end groups, water evaporation rate and sulfate middle groups have been compared with experimental data of sulfuric and super acid catalyzed polymerization runs. Very good agreement between model predictions and experimental data has been obtained for both catalyst systems over an extended range of conditions using the same set of model parameter values. It is worth noting that the model is also capable of predicting polymerization equilibrium.     

Palladium-Catalyzed Allylation of α-Nitroacetates with Propynes

A novel way to synthesize allylated α-nitroacetates under Pd catalysis has been described. Reactions of propynes with diverse α-nitroacetates in the presence of a catalytic amount of Pd(PPh₃)₄ and HOAc in 1,4-dioxane afforded the corresponding allylated products in good yields. Compared with other known methods, this method of synthesizing allylated α-nitroacetates generated no waste and needed neither a stoichiometric amount of base nor a leaving group.     

Ligand Control of Palladium-Catalyzed Site-Selective α- and γ-Arylation of α,β-Unsaturated Ketones with (Hetero)aryl Halides

This study describes the first palladium-catalyzed, site-selective α- and γ-arylation of α,β-unsaturated ketones with (hetero)aryl halides. A wide range of hetero(aryl)halides coupled with α,β-unsaturated ketones, and transformation into the arylated products proceeded with excellent to good yields. The site selectivity of the reaction is switchable by simply changing the phosphine ligand to access either α-arylated or γ-arylated products in good to excellent yields by using a low catalyst loading, and the method demonstrates good functional-group compatibility.     

Anionic Polymerization Behavior of α-Methylene-N-methylpyrrolidone

Anionic polymerization of α-methylene-N-methylpyrrolidone ( MMP ) was carried out in THF at −78∼0 °C with diphenylmethylpotassium (Ph₂CHK) and with diphenylmethyllithium (Ph₂CHLi) in the presence of Lewis acidic diethylzinc (Et₂Zn). Poly( MMP )s possessing predicted molecular weights based on the molar ratios between monomer and initiators and narrow molecular weight distributions (M_w/M_n < 1.1) were obtained in quantitative yields. It was demonstrated that the propagating chain end of poly( MMP ) was stable at −30 °C to form the polymers with well-defined chain structures. From the polymerizations at the various temperatures ranging from −50 to −30 °C, the apparent rate constant and the activation energy of the polymerization were estimated as follows: ln k = −6.93 × 10³/T + 25.7 and 57 ± 5 kJ mol⁻¹, respectively.     

Introduction of Constrained Cyclic Skeleton into β-Enaminoketonato Vanadium Complexes: A Strategy for Stabilization of Active Centre of Vanadium Catalyst for Ethylene Polymerization

Several novel mono( ?-enaminoketonato) vanadium complexes bearing constrained cyclic skeleton, including[(C6H5)C6H3C(O) = C(CH2)nCH = N ― Ar]VCl2(THF)2(V3a: n = 1, Ar = C6H5; V4a: n = 2, Ar = C6H5; V4b: n = 2, Ar =C6F5; V4c: n = 2, Ar =(C3H7)2C6H3; V5a: n = 3, Ar = C6H5), were synthesized and their structure and properties were characterized. The structures of V4 c and V5 a in solid-state were further confirmed by X-ray crystallographic analysis.Density functional theory(DFT) results indicated that these complexes showed enhanced steric hindrance around the metal center as compared with the acyclic analogues. Upon activation with Et2 Al Cl and in the presence of ethyl trichloroacetate as a reactivator, all of the complexes exhibited high catalytic activities(107 g PE/(mol V·h)) toward ethylene polymerization, and the obtained polymers exhibited unimodal distributions(Mw/Mn = 2.0-2.3) even produced at elevated temperatures(70-100 °C) and prolonged reaction time. When MAO was employed as a cocatalyst, they only showed moderate catalytic activities(105 g PE/(mol V·h)), but the resulting polymers had higher molecular weights(168-241 kg/mol). These vanadium complexes with cyclic skeleton also showed high catalytic activities toward ethylene/norbornene copolymerization. The produced copolymers displayed approximate alternating structure at high in-feed concentration of norbornene. The catalytic capabilities of these complexes could be tuned conveniently by varying ligand structure. Furthermore, the cyclic voltammetry results also proved that these complexes exhibited better redox stabilities than the complexes bearing linear skeleton.     

Amine-Borane Dehydrogenation and Transfer Hydrogenation Catalyzed by α-Diimine Cobaltates

Anionic α-diimine cobalt complexes, such as [K(thf)_1.5{(^DippBIAN)Co(η⁴-cod)}] ( 1 ; Dipp=2,6-diisopropylphenyl, cod=1,5-cyclooctadiene), catalyze the dehydrogenation of several amine-boranes. Based on the excellent catalytic properties, an especially effective transfer hydrogenation protocol for challenging olefins, imines, and N-heteroarenes was developed. NH₃BH₃ was used as a dihydrogen surrogate, which transferred up to two equivalents of H₂ per NH₃BH₃. Detailed spectroscopic and mechanistic studies are presented, which document the rate determination by acidic protons in the amine-borane.     

Ethylene Polymerization Catalyzed by Monocyclopentadienyl Titanium Complex Containing 8-Quinolinolato Ligand and ADF Study on the Formation Mechanism of Active Species

A monocyclopentadienyl titanium complex containing 8-quinolinolato (QCpTiCl_2) was synthesized. Its activities in ethylene polymerization at various Al/Ti molar ratios, different temperatures and activation time were investigated. The activity with a Al/Ti molar ratio of 500 exhibited a maximum of 2.8×10~5 g/(mol.h) at 30℃. The activation time of QCpTiCl_2 with MAO before polymerization also plays a role on the activity. The structural properties of the produced polyethylene (molecular weight, molecular weight distribution and melting point) were discussed. Kinetic behaviors of ethylene polymerization with the QCpTiCl_2/MAO system at different Al/Ti molar ratios were studied. For the QCpTiMeCl/MAO system and the CpTiMe_2Cl/MAO system, binding energies of the examined intermediates were calculated by quantum-mechanical method based on ADF program, respectively. It is confirmed that the chlorinebridged adduct formed by the reaction of QCpTiMeCl with MAO is thermodynamically steady. In the case of the QCp     

Influence of Backbone and Axial Substituent of Catalyst on α-Imino-ketone Nickel Mediated Ethylene (Co)Polymerization

Chinese Journal of Polymer Science - The α-imino-ketone nickel catalyst is an emerging versatile platform that is easy to prepare and allows for the production of branched high molecular...     

Polymerization Mechanism of α-Linear Olefin

The density functional theory on the level of B3LYP/6-31G was empolyed to study the chain growth mechanism in polymerization process of α-linear olefin in TiCl₃/AlEt₂Cl catalytic system to synthesize drag reduction agent. Full parameter optimization without symmetryrestrictions for reactants, products, the possible transition states, and intermediates wascalculated. Vibration frequency was analyzed for all of stagnation points on the potential energy surface at the same theoretical level. The internal reaction coordinate was calculated from the transition states to reactants and products respectively. The results showed as flloes:(i) Coordination compounds were formed on the optimum configuration of TiCl₃/AlEt₂Cl.(ii) The transition states were formed. The energy di?erence between transition states and the coordination compounds was 40.687 kJ/mol. (iii) Double bond opened and Ti-C(4) bond fractured, and the polymerization was completed. The calculation results also showedthat the chain growth mechanism did not essentially change with the increase of carbon atom number of α-linear olefin. From the relationship between polymerization activation energy and carbon atom number of the α-linear olefin, it can be seen that the α-linear olefin monomers with 6-10 carbon atoms had low activation energy and wide range. It was optimum to synthesize drag reduction agent by polymerization.     

Calixthiacrown:A New Multidentate Ligand for Platinum Metal

CalixarenesareafamilyofcyclicoligmerspreparedfromfOrmaldehydeandpara-substitutedphenolsviacycliccondensationunderalkalineconditions.Itwassuggestedthatthecalixarenescanbecountedasthethirdhostmoleculeorthethirdgenerationofsupramolecules,aftercrownethersandcyclodextrinst,,,j.TbeycanbeusedaspIatformsorbuildingblockstoconstructaseriesofcompoundsbavingpreorganizedstructures.Whencalixareneswerebridgedbypolyoxyetbylenecbainintra-orintermolecularyly,cal-.ixcrownswereobtained.Someofthelatterexhibitedou…     

Polymerization of α-Hydroxyacetylenes by Transition Metal Catalysts

Abstract

α-Hydroxyacetylenes (2-propyn-1-ol, DL-3-butyn-2-ol, 1-octyn-3-ol, 2-phenyl-3-butyn-2-ol) with a hydroxy functional group were polymerized by various Mo- and W-based catalysts. In general, the catalytic activities of Mo-based catalysts were greater than those of W-based catalysts for these polymerizations. In the polymerization of 2-propyn-l-ol, MoCl₅ alone and the MoCl₅-EtAlCl₂ catalyst system gave a quantitative yield of polymer. In the polymerization of 2-propyn-l-ol and its homologues by Mo-based catalysts, the polymer yield decreased as the bulkiness of the substituent increased. On the other hand, the polymer yield increased as the bulkiness of the substituent increased in WCl₆-EtAlCl₂-catalyzed polymerization. Polymers with a bulkier substituent showed better solubility in organic solvents than those without a substituent [e.g., poly (2-propyn-l-ol)]. The structures of the resulting polymers were characterized by various instrumental methods such as ¹H- and ¹³C-NMR, IR, and UV-visible spectroscopies. Thermogravimetric analyses and thermal transitions of the resulting polymers were also studied.     

Electron Effect of p-Substituent on Iron（Ⅱ） and Cobalt（Ⅱ） Pyridinebisimine Catalyst for Ethylene Polymerization

A series of 2,6-bis（imino）pyridyl iron and cobalt complexes bearing p-substituent [2,6-（ArN=CMe）2C5H3N]- MCl2 （Ar=2,6-Me2C6H3, 2,4,6-Me3C6H2, 2,6-Me2-4-BrC6H2, 2,6-Me2-4-ClC6H2, 2,4-Me2-6-BrC6H2, 2,4-Me2-6- ClC6H2, while M=Fe, Co） have been synthesized and investigated as catalysts for ethylene polymerization in the presence of modified methylaluminoxane as a cocatalyst. The electron effect and positions of the substituent of pyridinebisimine ligands were observed to affect considerably catalyst activity and polymer property.