Ti1－x(Hf0.919Zr0.081)xNiSn的制备及热电性能

采用固相反应法合成了单相的Ti_1-x(Hf_0.919Zr_0.081) _xNiSn (x＝0.00—0.15)，并用放电等离子烧结方法制备出密实块体材料. 研究 了Hf和Zr同时在Ti位上的等电子合金化对Ti基半Heusler化合物热电性能的影响规律. 结果 表明：少量的Hf和微量的Zr在Ti位上的等电子合金化，显著地降低了体系的热导率κ，同时 显著地提高了体系的Seebeck系数α. 组成为Ti_{0.85关键词： 半Heusler 固相反应 热电性能}     

Elastic properties, thermal expansion coefficients and electronic structures of Ti0.75X0.25C carbides

Elastic properties, thermal expansion coefficients and electronic structures of Ti_0.75X_0.25C carbides (X=W, Mo, Ta, Nb, V, Hf, Zr, Cr and Al) were systematically investigated using ab initio density functional theory (DFT) calculations. The calculated elastic moduli, electronic structures and thermal expansion coefficients α(T) of pure TiC are in good agreement with experimental data and other DFT calculations. Based on a phenomenological formula, the trends of elastic properties and ductile/brittle behavior of Ti_0.75X_0.25C were analyzed. It was found that alloying elements W, Mo, Ta, Nb, V and Hf can increase elastic moduli, while Zr, Cr and Al reduce moduli. The nearly free electron model and Debye approximation were applied in the evaluation of α(T). The anharmonic effect was taken into account by including volume-dependent elastic moduli and Debye temperature. Results show that alloying additions of 3d V, 4d Zr and Mo slightly reduce α(T), while 3d Cr increases α(T), Al, 4d Nb, 5d Hf and W almost keep α(T) unchanged in Ti_0.75X_0.25C at high temperatures. The electronic structures of Ti_0.75X_0.25C were calculated and analyzed, and the electronic density of states was used to interpret variations of elastic properties and ductile/brittle behavior induced by alloying additions.     

Hardness and microstructural variation of Al–Mg–Mn–Sc–Zr alloy

Variations of Vickers hardness were observed in Al–Mg–Mn alloy and Al–Mg–Mn–Sc–Zr alloy at different ageing times, ranging from a peak value of 81.2 HV at 54 ks down to 67.4 HV at 360 ks, below the initial hardness value, 71.8 HV at 0 ks for the case of Al–Mg–Mn–Sc–Zr alloy. Microstructures of samples at each ageing stage were examined carefully by transmission electron microscopes (TEMs) both in two-dimensions and three-dimensions. The presence of different types, densities, and sizes of particles were observed dispersed spherical Al₃Sc_1−xZr_x and also block-shaped Al₃Sc precipitates growing along <1 0 0>_Al with facets {1 0 0} and {1 1 0} of the precipitates. TEM analysis both in two-dimensions and three-dimensions, performed on various samples, confirmed the direct correlation between the hardness and the density of Al₃Sc.     

Prediction study of structural and elastic properties under pressure effect of M2SnC (M=Ti, Zr, Nb, Hf)

Using first-principles calculations, we have studied the structural and elastic properties of M₂SnC, with M=Ti, Zr, Nb and Hf. Geometrical optimization of the unit cell is in good agreement with the available experimental data. The effect of high pressures, up to 20 GPa, on the lattice constants shows that the contractions along the a-axis were higher than those along the c-axis. We have observed a quadratic dependence of the lattice parameters versus the applied pressure. The elastic constants and their pressure dependence are calculated using the static finite strain technique. A linear dependence of the elastic stiffnesses on the pressure is found. We derived the bulk and shear moduli, Young's moduli and Poisson's ratio for ideal polycrystalline M₂SnC aggregates. We estimated the Debye temperature of M₂SnC from the average sound velocity. This is the first quantitative theoretical prediction of the elastic properties of Ti₂SnC, Zr₂SnC, Nb₂SnC, and Hf₂SnC compounds.     

Atomic Scale Chemistry of α2/γ Interfaces in a Multi-Component TiAl Alloy

We report on the distribution of micro-alloying elements in a multi-component TiAl-based alloy. The specimen contains 3 at.% Nb, 1.5 at.% Cr, 0.5 at.% Mn, 0.6 at.% (W + Hf + Zr), and 0.2 at.% each of B, C, and O. The distributions of all micro-alloying elements with respect to the heterophase interface between α₂ and γ lamellae are analyzed with a three-dimensional atom-probe (3DAP) microscope. All the elements partition except boron, which resides primarily in boride precipitates. Oxygen, C, Mn, and Cr partition to the α₂-phase, whereas Nb and Zr partition to the γ-phase. Both W and Hf exhibit excess concentration values within ca. 7 nm of the lamellar interface in the α ₂-phase, and their near interfacial excesses are 0.26 and 0.35 atoms nm^?2, respectively.     

Theoretical investigation on the phase stability of Nd2Fe14B and site preference of V,Cr, Mn,Zr and Nb

The stability of the excellent permanent magnetic compound Nd₂Fe₁₄B and substitution of Fe in the compound by V, Cr, Mn, Zr and Nb are investigated by using interatomic pair potentials which are converted from lattice-inversion method. Calculation shows that the substitution always makes the cell volume larger, and the increase of the volume is almost linear with substituent concentration. The calculated cohesive energy shows that the preferential order of substitution of Fe is Nb, V, Cr, Mn, Zr. Nevertheless, all the five substituting elements should most preferentially replace Fe in the j₂ site, which has the greatest space among all six Fe sites.     

Insight into structural,mechanical, electronic and thermodynamic properties of intermetallic phases in Zr–Sn system from first-principles calculations

The structural, phase stabilities, mechanical, electronic and thermodynamic properties of intermetallic phases in Zr–Sn system are investigated by using first-principles method. The equilibrium lattice constants, enthalpy of formation (ΔH^form) and elastic constants are obtained and compared with available experimental and theoretical data. The configuration of Zr₄Sn is measured with reasonable precision. The ΔH^form of five hypothetical structures are obtained in order to find possible metastable phase for Zr–Sn system. The mechanical properties, including bulk modulus, shear modulus, Young's modulus and Poisson's ratio, are calculated by Voigt–Reuss–Hill approximation and the Zr₅Sn₄ and Zr₅Sn₃ show excellent mechanical properties. The electronic density of states for Zr₅Sn₄, Zr₅Sn₃ and cP8-Zr₃Sn are calculated to further investigate the stability of intermetallic compounds. Through the quasi-harmonic Debye model, the Debye temperature, heat capacity and thermal expansion coefficient under temperature of 0–300 K and pressure of 0–50 GPa for Zr₅Sn₃ and Zr₅Sn₄ are deeply investigated.     

Perturbation of the decay rate of90m Nb by implantation in metals

The perturbation of the decay constant of^90m Nb implanted in various transition metals (Zr, Nb, Hf, Ta, Ag and Au) has been determined by direct half-life measurements. Particular care was taken to evaluate and minimize possible systematic errors. The maximum relative change found is ν_Au?ν_Nb/ν_Nb=(4.5±0.8)%     

Structural and magnetic properties of Ti12M clusters (M=Sc to Zn)

The geometries, electronic, and magnetic properties of the 3d atom doped icosahedron (ICO) Ti₁₂M (M=Sc to Zn), where a dopant atom replaces either the centra l(Ti₁₂M^c) or surface (Ti₁₂M^s) Ti atom in ICO Ti₁₃ cluster, have been systematically investigated by using the density functional theory. The structures of all the optimized Ti₁₂M^c and Ti₁₂M^s clusters are distorted ICO. Sc, Ni, Cu, and Zn atoms prefer to displace surface Ti atom, V, Cr, Mn, and Fe atoms prefer to displace central Ti atom. The position of impurity atom depends on the strength of the interaction between the central atom and the surface atoms. As compared to the pure Ti₁₃ cluster, Ti₁₂M^c and Ti₁₂M^s (M=V, Fe, Co, and Ni) clusters are more stable, Ti₁₂M^c and Ti₁₂M^s (M=Sc, Cr, Mn, Cu, and Zn) are less stable. Both Ti₁₂Ni^s and Ti₁₂Ni^c are magic clusters, which originate from their electronic as well as geometric closed shells. Because the exchange interaction prevails over the crystal field in Ti₁₂M clusters, the valence electrons fill molecular orbitals in terms of Hund’s rule of maximum spin.     

Effects of Zr impurity on microscopic behavior of Hf metal

Hf metal with ∼ 3 wt% Zr impurity has been reinvestigated by perturbed angular correlation (PAC) spectroscopy using a LaBr₃(Ce)–BaF₂ detector set up to understand the microscopic behavior of this metal with temperature. From present measurements, five quadrupole interaction frequencies have been found at room temperature where both pure hcp fraction (∼33%) with 12 nearest neighbor Hf surrounding the probe ¹⁸¹Hf atom and the probe–impurity fraction (∼33%) corresponding to 11 nearest neighbor Hf plus one dissimilar Zr atom are clearly distinguished. At room temperature, the results for quadrupole frequency and asymmetry parameter are found to be ω_Q=51.6(4) Mrad/s, η=0.20(4) for the impurity fraction and ω_Q=46.8(2) Mrad/s, η=0 for the pure fraction with values of frequency distribution width δ=0 for both components. At 77 K, only 1 NN Zr impurity (∼93%) and pure hcp (∼7%) components have been found with a value of δ ∼ 10% for the impurity fraction. A drastic change in microstructural configuration of Hf metal is observed at 473 K where the impurity fraction increases to ∼ 50% and the pure hcp fraction reduces to ∼ 15% with abrupt changes in quadrupole frequencies for both components. The pure fraction then increases with temperature and enhances to ∼50% at 973 K. In the temperature range 473–973 K, quadrupole frequencies for both components are found to decrease slowly with temperature. Using the Arrhenius relation, binding energy (B) for the probe–impurity pair and the entropy of formation are measured from temperature dependent fractions of probe–impurity and pure hcp in the temperature range 473–773 K. The three other minor components found at different temperatures are attributed to crystalline defects.     

The first principle study of magnetic properties of Mn2WSn,Fe2YSn (Y=Ti,V), Co2YSn (Y=Ti,Zr, Hf,V, Mn) and Ni2YSn (Y=Ti,Zr, Hf,V, Mn) heusler alloys

The spin polarized electronic band structures, density of states (DOS) and magnetic properties of Mn₂WSn, Fe₂YSn (Y=Ti, V), Co₂YSn (Y=Ti, Zr, Hf, V, Mn) and Ni₂YSn (Y=Ti, Zr, Hf, V, Mn) huesler compounds are reported. The calculations are performed by using full-potential linearized augmented plane wave method (FP-LAPW) within density functional theory. The magnetic trend in these compounds is studied using values of magnetic moments, exchange interaction and calculated band gap. The results reveal that Mn₂WSn and Ni₂VSn show 100% spin polarization, Co₂YSn (Y=Ti, Zr, Hf, Mn), Fe₂YSn (Y=Ti, V), and Ni₂MnSn exhibit metallic nature and Ni₂YSn (Y=Ti, Zr, Hf) and Co₂VSn show semi-conducting behavior.     

Spatial spin-modulated structure and hyperfine interactions of 57Fe nuclei in multiferroics BiFe1–x T x O3 (T = Sc,Mn; x = 0, 0.05)

The results of the Mössbauer studies on ⁵⁷Fe nuclei in multiferroics BiFe_1–x T _x O₃ (T = Sc, Mn; x = 0, 0.05) in the temperature range of 5.2–300 K have been presented. The Mössbauer spectra have been analyzed in terms of the model of an incommensurate spatial spin-modulated structure of cycloid type. Information has been obtained about the effect of the substitution of Sc and Mn atoms for Fe atoms on the hyperfine parameters of the spectrum: the shift and the quadrupole shift of the Mössbauer line, the isotropic and anisotropic contributions to the hyperfine magnetic field, and also the parameter of anharmonicity of the spatial spin-modulated structure.     

掺杂对Ni51.5Mn25Ga23.5相变行为和磁性的影响

通过往母合金Ni_51.5Mn₂₅Ga_23.5掺入7种IVA, VA和VIA 过渡族元素得到系列掺杂合金Ni_51.5Mn₂₃M₂Ga_{23 .5}.M为掺杂元素.实验结果表明，掺杂效应一般引起马氏体相变温度的下降，其中，W 的掺杂是7种元素中唯一使相变温度升高的特例，且出现了中间马氏体相变.同时，在价电子 浓度不变的情况下，相变更敏感于原子的尺度效应.实验发现，Ti，Zr，Hf，V四种非磁性元 素的掺杂使Mn原子磁矩减小，而Nb，Ta，W三种非磁性元素的掺杂却可以明显地增大Mn原子 的磁矩.在考察掺杂效应时，不能忽略马氏体相变引起的晶格变化对材料磁性的影响. 关键词： NiMnGa 掺杂 马氏体相变 磁性     

Temperature dependence of the electric quadrupole interaction at scandium impurities in zirconium and hafnium

The PAC probe⁴⁴Sc was employed to study the magnitude and temperature dependence of the electric quadrupole interaction at the site of the transition metal Sc in the hexagonal host lattices Zr and Hf. In Zr ∼ 100% of the probe atoms were situated on regular lattice sites and a quadrupole interaction frequency of υ_Q=7.8(1)MHz was measured at room temperature. For Hf the fraction of the probe atoms on regular lattice sites was smaller and a damping of the interaction pattern (υ_Q=9.3(5)MHz at 293 K) could not be excluded. The temperature dependence of the electric field gradient in both host lattices was found to be weak.     

Structural, electronic and elastic properties of M2SC (M = Ti, Zr, Hf) compounds

Using ab initio calculations, we have studied the structural, electronic and elastic properties of M₂SC, with M = Ti, Zr and Hf. Geometrical optimization of the unit cell are in good agreement with the available experimental data. The band structures show that all three materials are conducting. The analysis of the site and momentum projected densities shows that the bonding is achieved through a hybridization of M-atom d states with S and C-atom p states. The Md-Sp bonds are lower in energy and are stiffer than Md-Cp bonds. The elastic constants are calculated using the static finite strain technique. We derived the bulk and shear moduli, Young's moduli and Poisson's ratio for ideal polycrystalline M₂SC aggregates. We estimated the Debye temperature of M₂SC from the average sound velocity. This is a quantitative theoretical prediction of the elastic properties of Ti₂SC, Zr₂SC, and Hf₂SC compounds, and it still awaits experimental confirmation.     

Mössbauer spectroscopy of the Zr-rich region in Zr–Nb–Fe alloys with low Nb content

Intermetallic phases and solid solutions in the Zr-rich region of the Zr–Nb–Fe system with low Nb content are studied by Mössbauer spectroscopy complemented with X-ray diffraction, optical and scanning electron microscopy and electron microprobe analysis. The phases found in each sample were those expected from the corresponding binary Zr–Fe system. Furthermore, one of the samples showed a ternary cubic Ti₂Ni type phase with a similar stoichiometry to the tetragonal Zr₂Fe compound. Mössbauer parameters were suggested to this phase (IS: - 0.12 mm/s, QS: 0.30 mm/s), to the bcc Zr(β) phase (IS: (-0.11 α 0.01) mm/s, QS: (0.23 α 0.02) mm/s), and to the hcp Zr(β^T) phase (IS: (-0.24 α 0.02) mm/s, QS: (0.45 α 0.02) mm/s).     

Stability and elastic properties of B2 CoX (X = Ti,Zr and Hf) intermetallic compounds as a function of pressure

By means of first-principles calculations within the generalised gradient approximation (GGA), phase stability, elastic properties and electronic structures of B2 CoX (X = Ti, Zr and Hf) compounds as a function of pressure have been investigated. The formation energy indicates that CoTi is the most stable phase in these three B2 phases under different pressures. The elastic properties of B2 Co (X = Ti, Zr and Hf), calculated via the Voigt–Reuss–Hill (VRH) approximation, increase with increasing pressure. The mechanical anisotropies are characterised by the universal anisotropy index (A^U) and the Zener anisotropy index (A^Z). The sound velocities, Debye temperatures and melting temperature under applied pressure are also evaluated. Electronic structure show that the changes in the charge distribution are moderate under applied pressure, resulting in the general characteristics of the bonding between X (X = Ti, Zr and Hf) and Co remain unchanged.     

Effect of compositional variation on the soft magnetic properties of Fe(87−x−y)CoxTi7 Zr6By amorphous ribbons

The effect of the replacement of Fe by Co or B on the thermal stability and soft magnetic properties of the Fe-based amorphous metallic ribbons with Fe_(87−x−y)Co_xTi₇Zr₆B_y (x = 10, 20% and y = 8, 10, 12%) produced by melt-spinning technique was investigated. For the melt-spun amorphous ribbons, the values of saturation magnetization and coercivity were observed to range from 107.00 to 152.38 emu/g and from 0.012 to 0.446 Oe, respectively. The thermal properties such as T_g, T_x, and ΔT_x were in the range of 796.7–809.6 K, 840.2–853.5 K, and 35.8–54.5 K, respectively. In the Fe–Co–Ti–Zr–B alloys, the Co substitution for Fe improved the soft magnetic properties but decreased the thermal stability. For magnetic properties, the coercivity (H_c) decreased and saturation magnetization (M_s) increased by the addition of Co. However, the supercooled liquid region (ΔT_x) decreased by the addition of Co. Meanwhile, the B substitution for Fe had no meaningful change on the thermal stability and soft magnetic properties. The amorphous ribbon of Fe₅₉Co₂₀Ti₇Zr₆B₈ exhibited the best soft magnetic properties such as the low coercivity of 0.025 Oe and the high saturation magnetization of 152.38 emu/g.     

Ab initio investigation into the structural, electronic and elastic properties of AlCu2TM (TM = Ti, Zr and Hf) ternary compounds

The Al-Cu-TM (TM = transition metal) alloy system has attracted great attention for both excellent glass-forming ability and its interesting physical properties. In this work, an investigation into the crystal, electrical and elastic properties of the AlCu₂TM (TM = Ti, Zr, and Hf) compounds has been conducted by first-principles calculations based on density-functional theory. The fully relaxed structure parameters of the AlCu₂TM compounds are in good agreement with previous experimental and other theoretical results. Besides, the cohesive energies of all the AlCu₂TM compounds have been evaluated. The energy band and densities of state of these compounds are also obtained. According to the calculated single crystal elastic constants, all the compounds are mechanically stable. The polycrystalline bulk moduli, shear moduli, Young’s moduli and Poisson’s ratio have been deduced by using Voigt-Reuss-Hill (VRH) approximations. The calculated negative Cauchy pressure and ratio of bulk modulus to shear modulus indicated that the AlCu₂TM compounds are ductile materials. The Debye temperatures of the AlCu₂TM compounds decrease with increasing the TM (Ti, Zr, and Hf) atomic number.     

Calculated structural, electronic and elastic properties of M2GeC (M=Ti, V, Cr, Zr, Nb, Mo, Hf, Ta and W)

Using ab initio calculations, we have studied the structural, electronic and elastic properties of M₂GeC, with M=Ti, V, Cr, Zr, Nb, Mo, Hf, Ta and W. Geometrical optimizations of the unit cell are in agreement with the available experimental data. The band structures show that all studied materials are electrical conductors. The analysis of the site and momentum projected densities shows that bonding is due to M d-C p and M d-Ge p hybridizations. The elastic constants are calculated using the static finite strain technique. The shear modulus C ₄₄, which is directly related to the hardness, reaches its maximum when the valence electron concentration is in the range 8.41–8.50. We derived the bulk and shear moduli, Young’s moduli and Poisson’s ratio for ideal polycrystalline M₂GeC aggregates. We estimated the Debye temperature of M₂GeC from the average sound velocity. This is the first quantitative theoretical prediction of the elastic constants of Ti₂GeC, V₂GeC, Cr₂GeC, Zr₂GeC, Nb₂GeC, Mo₂GeC, Hf₂GeC, Ta₂GeC and W₂GeC compounds, and it still awaits experimental confirmation.