Simplified derivatization method for the speciation analysis of organolead compounds in water and peat samples using in-situ butylation with tetrabutylammonium tetrabutylborate and GC-MIP AES

A simplified derivatization method for the speciation analysis of organolead compounds in environmental samples followed by gas chromatography-microwave induced plasma atomic emission detection is developed. An in-situ butylation using tetrabutylammonium tetrabutylborate in an acetate buffer medium of pH 4.0 with simultaneous extraction of the derivatized organolead species into hexane was performed; for the analysis of the peat samples, the desorption of the different species from the matrix by acid leaching was also included. Detection limits at the sub-ng L^–1 range, comparable to those achieved by Grignard-alkylation, were obtained for the different species. The accuracy of the method was confirmed by analysis of a standard reference material (BCR-CRM 605, road dust). Examples of applications for the analysis of tap water and peat are given. Received: 16 February 1998 / Revised: 25 May 1998 / Accepted: 29 May 1998     

Speciation of organolead compounds in water samples by GC-AAS after in situ butylation with tetrabutylammonium tetrabutylborate

A simple and reliable analytical method for the determination of organolead compounds in water samples has been developed by means of a gas chromatographic-atomic absorption system (GC-AAS). The derivatization of the organolead cations, necessary before their determination, was directly achieved in the water samples by the reagent tetrabutylammonium tetrabutylborate. Hexane/pentane was used to extract the butylated tetraorganolead compounds. The organic layer was dried and purified with sodium sulfate, concentrated by evaporation and injected into a GC-AAS system. The effects of various parameters on the derivatization and extraction procedures were studied and discussed.     

Gas chromatography--inductively coupled plasma--time-of-flight mass spectrometry for the speciation analysis of organolead compounds in environmental water samples

The application of inductively coupled plasma--time-of-flight mass spectrometry for the speciation analysis of organolead compounds in environmental waters is described. Construction of the transfer line was achieved by means of a relatively simple and rapid coupling procedure. Derivatization of the ionic lead species was achieved by in-situ propylation with sodium tetrapropylborate; simultaneous extraction of the derivatized compounds in hexane was followed by separation and detection by capillary gas chromatography hyphenated to inductively coupled plasma-time-of-flight mass spectrometry. Detection limits for the different organolead species ranged from 10 to 15 fg (as Pb), corresponding to procedural detection limits between 50 and 75 ng L(-1), on the basis of a 50 mL snow sample, extraction with 200 microL hexane, and subsequent injection of 1 microL of the organic extract on to the column. The accuracy of the system was confirmed by additional analysis of the water samples by capillary gas chromatography coupled with microwave-induced plasma-atomic-emission spectrometry and the analysis of a standard reference material CRM 605 (road dust) with a certified content of trimethyllead.     

Comparison of sodium tetraethylborate and sodium tetra(n-propyl)borate as derivatization reagent for the speciation of organotin and organolead compounds in water samples

The influence of pH on the propylation with sodium tetra(n-propyl)borate of butyl- and phenyltins as well as for trimethyl- and triethyllead was investigated. Ethylation and propylation with tetraalkylborates were compared with regard to derivatization yields and figures of merit for organotin compounds in real water samples. Similar results for limit of detection (3-12 ng/L as tin), derivatization yield (40-100%) and relative standard deviation of the method (3-10%) were achieved for derivatization with the two tetraalkylborates. Propylation is thus the preferred method for the simultaneous determination of environmentally relevant organotin and organolead compounds. The handling of the hygroscopic and air sensitive reagents NaBEt4 and NaBPr4 was simplified by dissolving them in tetrahydrofurane. The reagent solutions in tetrahydrofurane can be stored for at least one month at 4 degrees C in the dark without observing any decrease in the derivatization efficiency.     

Comparison of sodium tetraethylborate and sodium tetra(n-propyl)borate as derivatization reagent for the speciation of organotin and organolead compounds in water samples

The influence of pH on the propylation with sodium tetra(n-propyl)borate of butyl- and phenyltins as well as for trimethyl- and triethyllead was investigated. Ethylation and propylation with tetraalkylborates were compared with regard to derivatization yields and figures of merit for organotin compounds in real water samples. Similar results for limit of detection (3–12 ng/L as tin), derivatization yield (40–100%) and relative standard deviation of the method (3–10%) were achieved for derivatization with the two tetraalkylborates. Propylation is thus the preferred method for the simultaneous determination of environmentally relevant organotin and organolead compounds. The handling of the hygroscopic and air sensitive reagents NaBEt₄ and NaBPr₄ was simplified by dissolving them in tetrahydrofurane. The reagent solutions in tetrahydrofurane can be stored for at least one month at ¶4?°C in the dark without observing any decrease in the derivatization efficiency.     

Simplified method for determination of polycarbamate fungicide in water samples by liquid chromatography with tandem mass spectrometry following derivatization with dimethyl sulfate

A simple and sensitive analytical method for the determination of polycarbamate in water samples was developed. In this method, polycarbamate was cleaved under alkaline conditions and derivatized with dimethyl sulfate to methyl dimethyldithiocarbamate (DMDC-methyl) and dimethyl ethylenebisdithiocarbamate (EBDC-dimethyl). After the solid-phase extraction of the resulting methyl derivatives, they were measured by liquid chromatography with tandem mass spectrometry (LC-MS/MS), based on reversed-phase separation and MS/MS detection with positive atmospheric pressure chemical ionization. The absolute recoveries (mean+/-SD) all through the procedure from polycarbamate to DMDC-methyl and EBDC-dimethyl were 62.6+/-4.3 and 73.5+/-5.9%, respectively. The limits of detection and quantification of polycarbamate in the water samples were 0.061 and 0.20 microg/L in the form of DMDC-methyl, and 0.032 and 0.11 microg/L in the form of EBDC-dimethyl, respectively. The method was validated at levels of 0.25, 1.0, and 5.0 microg/L in the tap water and river water samples, and accuracy was achieved in the range of 94-109%. The proposed method can be applied to the determination of trace amounts of polycarbamate in environmental water samples.     

Solid-phase microextraction with on-fiber derivatization for the analysis of anti-inflammatory drugs in water samples

A sensitive and solvent-free procedure for the determination of non-steroidal acidic anti-inflammatory drugs in water samples was optimized using solid-phase microextraction (SPME) followed by on-fiber silylation of the acidic compounds and gas chromatography-mass spectrometry (GC-MS) determination. Microextraction was carried out directly over the filtered water samples using a polyacrylate fiber. Derivatization was performed placing the SPME fiber, loaded with the extracted analytes, in the headspace of a vial containing 50 microl of N-methyl-N-(tert-butyldimethylsilyl)-trifluoroacetamide (MTBSTFA). Derivatives were desorbed for 3 min in the GC injector. Influence of several parameters in the efficiency of microextraction (volume of sample, time, pH, type of fiber coating, etc.) and derivatization steps (time, temperature and volume of MTBSTFA) was systematically investigated. In the optimal conditions an excellent linearity over three orders of magnitude and quantification limits at the ng/l level (from 12 to 40 ng/l) were achieved. The proposed method was applied to the determination of acidic compounds in sewage water and results compared to those obtained using solid-phase extraction (SPE) followed by the derivatization of the compounds in the organic extract of the solid-phase extraction cartridge.     

Preconcentration speciation method for mercury compounds in water samples using solid phase extraction followed by reversed phase high performance liquid chromatography

A simple and rapid method for in situ preconcentration of inorganic and organic mercury compounds in water samples, based on solid phase extraction using dithizone immobilised on a reversed-phase C18 cartridge, has been developed. The adsorbed complexes were stable on the cartridge for at least 2 weeks. The speciation analysis of methylmercury (MeHg), phenylmercury (PhHg) and inorganic mercury (Hg (II)) were done by reversed-phase high performance liquid chromatography. The calibration graphs of MeHg, PhHg and Hg (II) were linear (r>0.999) from the detection limits (0.58, 0.66 and 0.54 ng) to 38, 25 and 26 ng of Hg, respectively. The average recoveries of MeHg, PhHg and Hg (II) from spiked samples (0.3-48.0 mug l(-1) Hg) were 98+/-3, 99+/-1 and 100+/-7%, respectively. By applying SPE procedure a 200-fold concentration of the sample was obtained.     

Inorganic arsenic speciation in various water samples with GFAAS using coprecipitation

A simple, economic and sensitive method for selective determination of As(III) and As(V) in water samples is described. The method is based on selective coprecipitation of As(III) with Ce(IV) hydroxide in presence of an ammonia/ammonium buffer at pH 9. The coprecipitant was collected on a 0.45 µm membrane filter, dissolved with 0.5 mL of conc. nitric acid and the solution was completed to 2 or 5 mL with distilled water. As(III) in the final solutions was determined by graphite furnace atomic absorption spectrometry (GFAAS). Under the working condition, As(V) was not coprecipitated. Total inorganic arsenic was determined after the reduction of As(V) to As(III) with NaI. The concentration of As(V) was calculated by the difference of the concentrations obtained by the above determinations. Both the determination of arsenic with GF-AAS in presence of cerium and the coprecipitation of arsenic with Ce(IV) hydroxide were optimised. The suitability of the method for determining inorganic arsenic species was checked by analysis of water samples spiked with 4–20 µg L^?1 each of As(III) and As(V). The preconcentration factor was found to be 75 with quantitative recovery (≥95%). The accuracy of the present method was controlled with a reference method based on TXRF. The relative error was under 5%. The relative standard deviations for the replicate analysis ( n?=?5) ranged from 4.3 to 8.0% for both As(III) and As(V) in the water samples. The limit of detection (3σ) for both As (III) and As(V) were 0.05 µg L^?1. The proposed method produced satisfactory results for the analysis of inorganic arsenic species in drinking water, wastewater and hot spring water samples.     

Simultaneous determination of organotin,organolead, and organomercury compounds in environmental samples using capillary gas chromatography with atomic emission detection

As part of a continuing evaluation of new analytical and sample preparation techniques conducted by the US Environmental Protection Agency (EPA), the use of capillary gas chromatography with atomic emission detection (GC-AED) for the simultaneous determination of organotin, organolead, and organomercury compounds in environmental samples was investigated. Pentylmagnesium bromide was used to pentylate ionic organotin, organolead, and organomercury compounds; the pentyl derivatives were then separated by GC and determined by AED. Several important GC-AED parameters, including the type of injector inlet, carrier gas flow rate, and helium make-up gas flow rate, were optimized for the simultaneous determination of these organometallic compounds. Their minimum detectable concentrations were approximately 1.0 to 2.5 ng/mL using a 0.5-μL on-column injection. The calibration curves exhibited good linearity between 2.5 and 2500 ng/mL for organotin and organolead compounds, and between 2.5 and 10000 ng/mL for organomercury compounds.     

Headspace sampling with in situ carbodiimide-mediated derivatization for the determination of ibuprofen in water samples

A method using headspace generation and in situ derivatization with water soluble EDC (1-[3-(dimethylamino)propyl]-3-ethylcarbodiimide) and TFEA (2,2,2-trifluoroethylamine) has been optimized for the determination of ibuprofen (2-(p-isobutylphenyl)propionic acid), one of the most common non-steroid anti-inflammatory drug (NSAIDs) residues in surface and wastewater samples. Derivatization was carried out in the vial of the headspace sampler (HS) in only 15 min, after which instrumental measurements were made with gas chromatography-mass spectrometry (GC-MS). As the injection system, a programmed temperature vaporizer (PTV) in the solvent-vent injection mode is proposed in order to increase the sensitivity of the measurements. The effects of the variables affecting HS generation, the derivatization reaction, and the instrumental PTV conditions were studied. A limit of quantification as low as 32 ng/L was achieved, and repeatability values were below 10%. Accuracy of the method was evaluated using spiked ultrapure water at three concentration levels, obtaining apparent recoveries between 96% and 104%. The proposed method was applied to the quantification of ibuprofen in sea water and urban wastewater samples.     

Improved liquid-liquid-liquid microextraction method and its application to analysis of four phenolic compounds in water samples

An improved liquid-liquid-liquid microextraction (LLLME) technique has been put forward based on the principle of single drop LLLME. In the technique, a vial insert was firstly utilized as acceptor phase container. Because the diameter of the bottom of the vial insert was small, the contact area between the acceptor phase and the vial insert was bigger than that between microsyringe and microdrop of acceptor phase in single drop LLLME, and the stability of microdrop was increased markedly. More acceptor phase could be held in the improved method than that in single drop LLLME, and the sensitivity of the method was increased. The sample vial and vial insert were horizontally placed so that the density of organic solvent has little effect on the selection of organic solvents. Aqueous ammonia and toluene were selected as the acceptor phase and the organic phase, respectively. The improved method was successfully applied to determine four phenolic compounds in real aqueous samples. Good recoveries that ranged from 82.2% to 117.2% were obtained. The intra-day and inter-day reproducibilities (RSD) were under 4.8% and 6.8%, respectively. The extraction efficiency of the improved method was 11-47 times higher than that of single drop LLLME method. The improved LLLME method is economical, rapid, simple, efficient, low organic solvent consumption and no cross-containment. This method is very suitable for the extraction of ionizable and chargeable analyte in complex environmental or biological samples.     

Determination of phenoxy herbicides in water samples using phase transfer microextraction with simultaneous derivatization followed by GC‐MS analysis

A sensitive and accurate method for the determination of two model phenoxy herbicides, 4‐chloro‐2‐methylphenoxy acetic acid and 4‐chloro‐2‐methylphenoxy propanoic acid, in water is explained. This method utilizes a simple phase transfer catalyst‐assisted microextraction with simultaneous derivatization. Factors affecting the performance of this method including pH of the aqueous matrix, temperature, extraction duration, type and amount of derivatization reagents, and type and amount of the phase transfer catalyst are examined. Derivatization and the use of phase transfer catalyst have proven to be especially vital for the resolution of the analytes and their sensitive determination, with an enrichment factor of 288‐fold for catalyzed over noncatalyzed procedure. Good linearity ranging from 0.1 to 80 μg L^?1 with correlation of determination (r²) between 0.9890 and 0.9945 were obtained. Previous reported detection limits are compared with our new current method. The low LOD for the two analytes (0.80 ng L^?1 for 4‐chloro‐2‐methylphenoxy propanoic acid and 3.04 ng L^?1 for 4‐chloro‐2‐methylphenoxy acetic acid) allow for the determination of low concentrations of these analytes in real samples. The absence of matrix effect was confirmed through relative recovery calculations. Application of the method to seawater and tap water samples was tested, but only 4‐chloro‐2‐methylphenoxy propanoic acid at concentrations between 0.27 ± 0.01 and 0.84 ± 0.06 μg L^?1 was detected in seawater samples.     

Reversed-phase liquid chromatographic method for the analysis of aminoglycoside antibiotics using pre-column derivatization with phenylisocyanate

A pre-column derivatization liquid chromatographic method has been developed for the analysis of aminoglycoside antibiotics using phenylisocyanate as a derivatization reagent. Derivatives including kanamycin, neomycin and gentamicin were formed by reaction of the analytes with phenylisocyanate in the presence of triethylamine. Phenylisocyanato groups were attached to corresponding amino groups of aminoglycoside and their molecular mass was confirmed by liquid chromatography-electrospray ionization-mass spectrometry (LC-ESI-MS). The experimental conditions for derivatization and separation of aminoglycoside derivatives were optimized and validated. A simple liquid chromatographic method for the determination of aminoglycoside antibiotics was demonstrated.     

Applicability of solid-phase microextraction combined with gas chromatography atomic emission detection (GC-MIP AED) for the determination of butyltin compounds in sediment samples

The performance of solid-phase microextraction (SPME) applied to the determination of butyltin compounds in sediment samples is systematically evaluated. Matrix effects and influence of blank signals on the detection limits of the method are studied in detail. The interval of linear response is also evaluated in order to assess the applicability of the method to sediments polluted with butyltin compounds over a large range of concentrations. Advantages and drawbacks of including an SPME step, instead of the classic liquid–liquid extraction of the derivatized analytes, in the determination of butyltin compounds in sediment samples are considered in terms of achieved detection limits and experimental effort. Analytes were extracted from the samples by sonication using glacial acetic acid. An aliquot of the centrifuged extract was placed on a vial where compounds were ethylated and concentrated on a PDMS fiber using the headspace mode. Determinations were carried out using GC-MIP AED.     

A study of method robustness for arsenic speciation in drinking water samples by anion exchange HPLC-ICP-MS

Regulating arsenic species in drinking waters is a reasonable objective, since the various species have different toxicological impacts. However, developing robust and sensitive speciation methods is mandatory prior to any such regulations. Numerous arsenic speciation publications exist, but the question of robustness or ruggedness for a regulatory method has not been fully explored. The present work illustrates the use of anion exchange chromatography coupled to ICP-MS with a commercially available "speciation kit" option. The mobile phase containing 2 mM NaH(2)PO(4) and 0.2 mM EDTA at pH 6 allowed adequate separation of four As species (As(III), As(V), MMAA, DMAA) in less than 10 min. The analytical performance characteristics studied, including method detection limits (lower than 100 ng L(-1) for all the species evaluated), proved the suitability of the method to fulfill the current regulation. Other parameters evaluated such as laboratory fortified blanks, spiked recoveries, and reproducibility over a certain period of time produced adequate results. The samples analyzed were taken from water utilities in different areas of the United States and were provided by the U.S. EPA. The data suggests the speciation setup performs to U.S. EPA specifications but sample treatment and chemistry are also important factors for achieving good recoveries for samples spiked with As(III) as arsenite and As(V) as arsenate.     

Simplified analysis of organic compounds in headspace and aqueous samples by high-capacity sample enrichment probe

A sample enrichment probe (SEP) consisting of a thin rod of an inert material and provided at one end with a short sleeve of polydimethylsilicone rubber was used for the high-capacity sample enrichment of analytes from gaseous and aqueous samples for analysis by gas chromatography (GC) and its hyphenated techniques. The silicone rubber was exposed to the analytical sample, after which the end of the rod carrying the silicone rubber was introduced into the injector and the analytes thermally desorbed and analysed by GC. This technique is similar to, but differs from, solid-phase microextraction (SPME) in that a much larger volume of the sorptive phase is employed, the sorptive phase is not introduced into the inlet of the GC via a needle and the injector is opened to the atmosphere for the introduction and removal of the SEP. In the determination of volatile and semi-volatile organic compounds in gaseous and aqueous media, the SEP technique gave results comparable with those obtained by the stir-bar-sorptive extraction (SBSE) and high-capacity sorption probe (HCSP) techniques. Implementation of the SEP technique requires only minor adaptations to the gas chromatograph and does not require any auxiliary thermal desorption and cryotrapping equipment.