微穿孔板和微缝板吸声体研究进展

介绍了我国在新型吸声体微穿孔板和微缝板的特点、首创、理论分析、加工制作、多方面的应用情况，以及其在国外的影响。也讨论了这些吸声体的部分发展方向。     

关于微穿孔板吸声体频带宽度极限的讨论

依据马大猷教授的微穿孔板吸声体准确理论,利用计算机辅助设计对于该结构频带宽度极限情况从理论上进行了讨论,把极限频宽和最大吸声系数的制约关系量化,并得到此情况下应用于低频或高频环境孔径的选用范围,以及此情况下板厚和穿孔率与传统观念不同的特点。以上分析结果以及所提供的结构参数为宽频带微穿孔板的具体设计提供有价值的参考。     

微穿孔板吸声结构水下应用研究

马大猷教授提出的微穿孔板吸声结构在空气噪声降低和隔离方面得到了广泛的应用,但未见水下应用的相关研究和报道。本文将空气中微穿孔板理论应用到水中,得到了水下微穿孔板吸声结构的吸声公式。通过理论分析,得出了微穿孔板结构直接应用于水中无法获得宽频吸收的结论。提出了通过匹配液将微穿孔板间接应用到水下的设想。设计了单层板和双层板吸声结构,并对它们的吸声特性进行了理论分析与仿真。结果表明,本文设计的微穿孔板吸声结构在水中能够获得优于空气中的宽频带吸声效果。实验测量了自制的微穿孔板吸声结构,吸声系数的测量值与理论曲线基本吻合,从而验证了理论分析的正确性。     

穿孔率和穿孔直径耦合下微穿孔板吸声体整体吸声性能

微穿孔板几何参数的耦合性及其对整体吸声性能的影响,对于设计微穿孔板吸声体和优化其工作性能具有指导作用。根据微穿孔板吸声体基本理论,研究了穿孔率和穿孔直径双参数耦合作用下微穿孔板吸声体的整体吸声性能。穿孔率和穿孔直径之间的耦合性与其本身取值密切相关,而与板厚和板后腔深无明显关系;在穿孔率-穿孔直径参数域上,吸声体存在吸声系数为1.0的吸收峰,整体吸声性能随穿孔率或穿孔直径从小到大变化,呈现出先增强后减弱的变化趋势。该结论能够准确解释微穿孔板受粉尘污染后吸声性能的变化规律和演变路径。论文的工作为设计微穿孔板吸声体提供了一种新的理论依据和实施方法。     

计及孔间相互作用的微穿孔板吸声特性研究

计算微穿孔板吸声系数时,假设孔间的相互作用可以忽略。计算具有不同直径微孔的穿孔板吸声系数并提高其计算精度,孔间的相互作用不能再忽略。在马大猷、Melling(梅尔林)等前人研究的基础上,根据声波辐射和传播原理,分析微孔之间的相互作用,通过修正微孔的实际等效长度,得到计及孔间相互作用微孔板吸声系数模型,并进行理论计算和实验测试。研究结果表明:影响微穿孔板吸声系数除结构参数外,还应考虑孔间的相互作用;计及微孔板各孔间相互作用,能提高共振频率、吸声系数理论值的计算精度,计算值逼近实验测试结果。     

穿纤维微穿孔板吸声系数的有限元仿真

为拓宽微穿孔板的吸声频带,该文用有限元算法建立了典型微穿孔板和穿入不同数量金属纤维的微穿孔板模型,研究了两种微穿孔板的吸声系数、声阻抗和微孔内法向质点速度的空间分布,并进行了试验验证。有限元仿真和试验数据表明:穿入金属纤维可以拓宽微穿孔板的吸声频带,吸声系数也随纤维根数的增加而下降;吸声系数仿真结果与试验结果趋势一致,仿真模型可以有效模拟穿入纤维前后微穿孔板的吸声特性;穿入金属纤维导致黏滞效应引起的低质点速度区域增大,声阻增加,引起吸声系数的降低,而声抗变化不大。研究发现,有限元仿真方法适用于结构相对复杂的微穿孔结构的声学建模,能直观地体现微孔复杂结构的影响,值得继续深入研究和工程应用。     

水下弹性微穿孔吸声结构吸声系数研究

利用模态叠加法建立了水介质微穿孔板的数学模型,基于声电类比法得到其等效电路模型。研究了弹性微穿孔板和弹性背腔对垂直入射吸声系数的影响。与空气介质中的微穿孔板不同,水下微穿孔板因结构阻抗不足,难以取得满意的吸声效果,为此提出了增强型微穿孔吸声结构,并在水介质阻抗管内对理论结果予以验证。结果表明,随着增强型弹性微穿孔板弯曲刚度的增大,其在[20,2000]Hz范围内的平均吸声系数得到提高,逐步趋近于刚性微穿孔板的结果,弹性背板使微穿孔吸声结构的吸声峰向低频移动,低频吸声效果得到提高。     

一种微穿孔板消声器

本文根据马大猷教授提出的“微穿孔板吸声体精确理论”，在对微穿孔板消声器结构参数与吸声特性之间的相互影响进行了分析的基础上，设计了微穿孔板消声器并将其应用在新舟60飞机APU(辅助动力装置)降噪的实际工程中，并通过编写的噪音数据采集分析程序，对降噪效果进行了测试和分析，验证出微穿孔板消声器对消除飞机的APU的排气噪声具有良好的消声效果，平均降噪7．16dB。     

阻尼耦合双层微穿孔板吸声体研究

提出并研究一种利用两板间微缝进行阻尼耦合的双层微穿孔板(DMPP)吸声体。该吸声体在两层微穿孔板(MPP)之间形成一个宽度小于1mm的微缝,因此其阻尼不仅可由板上的微穿孔提供,还可由两板之间形成的微缝提供。采用声电类比法建立了DMPP转移阻抗的理论模型,并进行实验验证,结果表明理论计算结果与实验吻合较好。然后利用建立的理论模型,对单层MPP和DMPP吸声体的吸声性能进行了对比研究,结果表明,相比于单层MPP,DMPP可以利用微缝提供的阻尼显著改善吸声性能,同时减少实际板厚。最后,对DMPP吸声体的吸声性能及其几何参数的关系进行研究,结果表明,当保持其它结构参数不变时,微缝宽度对DMPP吸声系数的提高存在一个最优值,超过或低于此值会导致吸声系数下降。     

波纹穿孔板吸声特性研究

研究了平面波垂直入射和掠入射两种情况下波纹穿孔板对声波的耗散作用, 结果表明在这两种情况下波纹穿孔板的声学特性都有别于平板穿孔板。在垂直入射条件下, 通过“等效穿孔率”可以在中、低频率范围内使波纹穿孔板和平板穿孔板的吸声特性“重合”。波纹穿孔板在高频范围会出现异于平板穿孔板的双尖峰现象, 进一步研究发现这是由波纹板形状导致的背腔深度的连续变化所引起的。在掠入射条件下, 波纹穿孔板与平板穿孔板无法通过“等效穿孔率”替代。波纹穿孔板的板高和板长对其声学性能都有明显影响, 当波纹穿孔板夹角(板高与1/4板长对应的正切角)相同时, 在板长小于75 mm范围内波纹穿孔板有相似的声学性能。

     

Improving low-frequency sound absorption of micro-perforated panel absorbers by using mechanical impedance plate combined with Helmholtz resonators

The traditional Micro-perforated plate (MPP) is a kind of clean and non-polluting absorption structure in the middle and high frequency and has been widely used in the field of noise control. However, the sound absorption performance is dissatisfied at low frequencies when the air-cavity depth is restricted. In this paper, a mechanical impedance plate (MIP) is introduced into the traditional MPP structure and a Helmholtz resonator is attached to the MIP. Mechanical impedance plate (MIP) provides a good absorption at low frequency by using mechanism of mechanical resonance and the acoustic energy is dissipated in the form of heat with viscoelastic material. Helmholtz resonator can fill in the defect of the poor absorption effect between the Micro-perforated plate (MPP) and the mechanical impedance plate (MIP). The acoustic impedance of the proposed sound absorber is investigated by using acoustic electric analogy method and impedance transfer method. The influence of the tube’s length of Helmholtz resonator and the number of Helmholtz resonator on the sound absorption is studied. The corresponding results are in agreement with the theoretical calculation and prove that the composite structure has the characteristics of improving the low frequency sound absorption property.     

Improvement of sound absorption characteristics under low frequency for micro-perforated panel absorbers using super-aligned carbon nanotube arrays

Super-aligned carbon nanotube (SACNT) arrays are grown on the surface of micro perforated panel (MPP) in the hope of improving the acoustic performance of MPP absorbers by virtue of their unique properties. Scanning electron microscopy reveals that SACNT arrays did not block the perforations of MPPs or changed the perforation diameter due to their “super-aligned” nature, although MPPs are thickened. The absorption effect of SACNT arrays which are of the same and different lengths with different incident side on MPP absorbers are investigated, and standing wave tube method is used to determine the normal sound absorption coefficient. Results show that both of the lengths of SACNT arrays and the incident side have effects on the sound absorption performance of MPP absorbers. And generally SACNT arrays help to improve the sound absorption capacity of MPP absorbers in low-frequency regions only when the SACNT arrays surface is the incident side. SACNT arrays decrease absorption performance of MPP absorbers when the MPP surface is used as the incident side. Moreover, SACNT arrays are found to increase the acoustic ability of MPP absorbers with the same structure parameters monotonically at lengths up to 600 μm in the condition that the SACNT arrays surface is used as the incident side.     

Sound absorption of a double-leaf micro-perforated panel with an air-back cavity and a rigid-back wall: Detailed analysis with a Helmholtz-Kirchhoff integral formulation

So far the electro-acoustical equivalent circuit analysis has been widely used to analyse micro-perforated panel (MPP) absorbers, however, as for the double-leaf MPP the equivalent circuit analysis inevitably includes an approximation. In this paper, the sound absorption characteristics of a double-leaf MPP absorber backed by a rigid wall are analysed by wave theory using Helmholtz-Kirchhoff integral formulation to obtain a strict solution. The present wave theory is experimentally validated with existing measured results. The theory is also compared with the equivalent circuit solutions so that the differences between the two theories appear and the effect of the approximation is clarified. The comparison shows that the difference mainly appears in the vicinity of the resonance peaks: the differences occur in the resonance frequencies and the absorption coefficient at frequencies between the two resonance peaks.     

A note on the prediction method of reverberation absorption coefficient of double layer micro-perforated membrane

The absorption performance of micro-perforated absorber (MPA) has been usually estimated by equivalent circuit (EC), however, it has been noted that the predicted absorption coefficient by EC does not agree completely with the experiment in some frequency range. Hence impedance transfer method (ITM) is adopted to predict the reverberation absorption coefficient of a double layer micro-perforated membrane (MPM) structure. Experimental studies show that the prediction of ITM is better than that of EC.     

微穿孔板几何参数估算及其对吸声性能的影响

不规则孔微穿孔板几何参数无法直接获知,造成吸声性能计算困难,故提出一种微穿孔板几何参数估算方法。将不规则孔等效处理为圆孔,利用马氏理论关于圆孔微穿孔板的基本理论,建立了微穿孔板几何参数估算模型;将参数估算结果用于吸声性能预测,理论计算与实验结果吻合。根据微穿孔板几何参数对高吸声性能区域的影响,探讨了马氏理论适用极限与微穿孔板几何参数的关系,以及微穿孔板受粉尘污染后吸声性能演变规律。将微穿孔板参数点取在面积较大的高吸声性能区域中间部位,可获得较大的马氏理论适用极限;微穿孔板参数点位于高吸声性能区域右上部位时,一定程度的粉尘污染不会降低吸声性能.     

Hybrid device for acoustic noise reduction and energy harvesting based on a silicon micro-perforated panel structure

A kind of hybrid device for acoustic noise reduction and vibration energy harvesting based on the silicon micro- perforated panel （MPP） resonant structure is investigated in the article. The critical parts of the device include MPP and energy harvesting membranes. They are all fabricated by means of silicon micro-electro-mechanical systems （MEMS） tech- nology. The silicon MPP has dense and accurate micro-holes. This noise reduction structure has the advantages of wide band and higher absorption coefficients. The vibration energy harvesting part is formed by square piezoelectric membranes arranged in rows. ZnO material is used as it has a good compatibility with the fabrication process. The MPP, piezo- electric membranes, and metal bracket are assembled into a hybrid device with multifunctions. The device exhibits good performances of acoustic noise absorption and acoustic-electric conversion. Its maximum open circuit voltage achieves 69.41 mV.     

A note on the relationship between the sound absorption by microperforated panels and panel/membrane-type absorbers

The sound absorption mechanism of microperforated panel (MPP) absorbers and panel/membrane-type absorbers is both based on a certain resonance system and utilising its resonance effect. However, the relationship between the absorption mechanisms of MPPs and panel/membrane-type absorbers has not been discussed: it is not clarified whether they can occur simultaneously, or how they interfere each other. On the other hand, in a previous study there is an attempt to cause both absorption mechanisms simultaneously. In this paper, using an electro-acoustical equivalent circuit model, their sound absorption mechanisms and their relationship are discussed. In this study, three cases are considered: (1) the case in which only the mass reactance of the MPP is considered, (2) the case in which the losses of the panel is considered, and (3) the case in which the sound absorption of the back wall surface is considered. The results suggest that the microperforated panel absorption, which is Helmhotz-type resonance, and the panel/membrane-type absorption can be regarded as phenomena of the same kind which can be smoothly transformed into each other by changing a parameter, and can be consistently modelled and comprehensively discussed.     

基于衰减振荡信号特征参数和伪阻抗的电路参数计算方法

本文研究了基于暂态信号中衰减振荡信号的电路参数计算理论和方法.在电力系统线路发生故障时,通过计算暂态信号流通路径电路参数可确定故障位置、推断故障原因,而衰减振荡信号作为暂态信号主要成分,因此分析基于衰减振荡信号的电路参数计算在电力系统故障定位中有重要理论价值和实际工程意义.结合R-L电路和R-C电路,首先推导了时域衰减振荡电压、电流信号特征参数与各元件参数以及电路参数间定量关系;并分析了电路在衰减振荡信号下阻抗特性,结合稳态正弦分量阻抗概念,将电路流经衰减振荡信号时的阻抗特性定义为伪阻抗,并确定了伪阻抗与电路参数和信号特征参数间的关系;同时分析了串并联条件下伪阻抗与元件参数关系.以此为基础分别提出了基于信号特征参数和基于伪阻抗的电路参数计算理论,结合现有衰减振荡信号特征提取方法,提出具体计算方法,为基于衰减振荡信号的电路参数计算理论发展以及实际工程应用奠定了重要基础.通过MATLAB模拟产生故障信号对所提理论和方法进行验证,结果证明了所提理论和方法的正确性和准确性,并以实际电网故障信息为基础,基于PSCAD/EMTDC建立实际配网模型并对实际单相接地故障进行重现,对配网单相接地故障进行定位分析,结果证明了方法的可行性.