Empirical correlation between melting temperature and cohesive energy of binary Laves phases

A list of 143 binary Laves phases with their melting temperature and melting type is collected, and used to study a correlation between melting temperature and cohesive energy. It is found that the melting temperature of Laves phases is roughly proportional to its cohesive energy calculated by Miedema's empirical model from their intrinsic atomic properties. The average predicted error of melting temperature of compounds is as low as 8.0%. This empirical rule is consistent with the result of the universal binding energy theory of solids.     

Selected properties of EuCo2(Si1−xGex)2 alloys

EuCo₂(Si_1−xGe_x)₂, x=0, 0.1, 0.2, 0.3, 0.4, 0.5, 0.6, 0.7, 0.8, 0.9, 1 samples were synthesised by induction melting followed by annealing at 900 °C and rapid quenching. X-ray powder diffraction and Auger electron spectroscopy studies revealed that solid solutions are formed only for x?0.2 and x?0.7. Magnetic susceptibility investigations for the solid solutions revealed a dominant divalent europium valence state in the germanium-rich samples and a dominant trivalent europium component in the silicon-rich samples. In the germanium-rich samples, a long-range antiferromagnetic ordering was observed. In all samples studied, additional magnetic transitions at various temperatures were detected, which could be attributed to small clusters containing different europium chemical surrounding from that in the predominant phase.     

Synthesis and crystallographic studies of garnet-type AgCa2Mn2V3O12 and NaPb2Mn2V3O12

High-purity powder specimens of AgCa₂Mn₂V₃O₁₂ and NaPb₂Mn₂V₃O₁₂ have been successfully synthesized by solid-state chemical reaction. The Rietveld refinements from X-ray powder diffraction data verified that these compounds have the garnet-type structure (space group , No. 230) with the lattice constant of a=12.596(2) Å for AgCa₂Mn₂V₃O₁₂ and a=12.876(2) Å for NaPb₂Mn₂V₃O₁₂. Calculation of the bond valence sum supported that Mn is divalent and V is pentavalent in these garnets. Estimation of the quadratic elongation and the bond angle variance showed that the distortions of the MnO₆ octahedra and the VO₄ tetrahedra are significantly suppressed. Our new results of AgCa₂Mn₂V₃O₁₂ and NaPb₂Mn₂V₃O₁₂ are compared to those of AgCa₂M₂V₃O₁₂ and NaPb₂M₂V₃O₁₂ (M=Mg, Co, Ni, Zn).     

Glass formation in the As2Se3-As2Te3-Sb2Te3 system

Chalcogenide glasses from the As₂Se₃-As₂Te₃-Sb₂Te₃ system were synthesized for the first time. The glass-forming region was determined by X-ray diffraction and electron microscopic analyses.The basic physicochemical parameters such as density (d), microhardness (HV) and temperatures of phase transformations (glass transition T_g, crystallization T_cr and melting T_m) were measured. Compactness and some thermomechanical characteristics such as volume (V_h) and formation energy (E_h) of micro-voids in the glassy network as well as the elasticity module (E) were calculated. The glass-forming ability was evaluated according to Hruby's criteria (K_G). The correlation between composition and properties of the (As₂Se₃)_x(As₂Te₃)_y(Sb₂Te₃)_z glasses was established and comprehensively discussed.     

Neutron and X-ray diffraction studies on the Tb2Ni3Si5 single crystal

Neutron and X-ray diffraction studies on the Tb₂Ni₃Si₅ single crystal have been done to investigate its crystal modulation and magnetic properties. The modulated single crystal is constructed by the TbNiSi₂ (CeNiSi₂-type Cmcm) and the Tb₂Ni₃Si₅ (U₂Co₃Si₅-type Ibam) lattices. The relationship between the two lattices is described as direction of the b₁₁₂-axis coincides with the a₂₃₅-axis. The crystal modulation gives significant effects on magnetism. Each of the two lattices takes complex antiferromagnetism with multiplex propagation vectors.     

Synthesis and characterization of Co7(OH)12(C2H4S2O6)(H2O)2—a single crystal structural study of a ferrimagnetic layered cobalt hydroxide

A novel layered hydrotalcite-like material, Co₇(H₂O)₂(OH)₁₂(C₂H₄S₂O₆), has been prepared hydrothermally and the structure determined using single crystal X-ray diffraction (a=6.2752(19) Å, b=8.361(3) Å, c=9.642(3) Å, α=96.613(5)°, β=98.230(5)°, γ=100.673(5)°, R1=0.0551). The structure consists of brucite-like sheets where 1/6 of the octahedral sites are replaced by two tetrahedrally coordinated Co(II) above and below the plane of the layer. Ethanedisulfonate anions occupy the space between layers and provide charge balance for the positively charged layers. The compound is ferrimagnetic, with a Curie temperature of 33 K, Curie-Weiss θ of −31 K, and a coercive field of 881 Oe at 5 K.     

Synthesis of high tap density Li3V2(PO4)3 cathode materials using mixed lithium precursors

High tap density Li₃V₂(PO₄)₃ cathode materials were synthesized using mixed LiF and LiNO₃ as lithium precursors, LiNO₃ was used as the sintering agent. Rietveld refinement results show that no impurities phases are detected in products. Particle size distribution and tap density measurement results show that particle size and tap density of products can be increased by the addition of LiNO₃. Electrochemical characterization results show that electrochemical performance of products is declined with the increase in contents of LiNO₃ in the lithium precursors. Only a small amount of LiNO₃ added in the lithium precursors (mole ratio of LiNO₃ to LiF is 1:9) can increase the tap density and also retain the good performance of products. Scanning electron microscopy (SEM) images indicate that the samples prepared by mixed lithium precursors present particles agglomerate, and the particle size increased with increase in contents of LiNO₃. Large amount of LiNO₃ added in the lithium precursors induces the particles to become spheric and smooth, which worsens the performance. The particles obtained with the mole ratio of LiNO₃ to LiF in 1:9 show a flake-like shape with a high specific surface area, which leads to good electrochemical performance.     

Homogeneity range and crystal structure of Ni substituted Mg6(Pd,Ni) complex intermetallic compounds

The solubility of nickel in Mg₆Pd compound has been studied by chemical and structural methods. The solubility limit at 673 K attains 9 at% Ni, i.e. more than four times the value previously reported. Therefore, a re-determination of the ternary Mg-Pd-Ni phase diagram in the Mg-rich corner is desirable. Mg₆(Pd,Ni) compounds have the same crystal structure as the binary Mg₆Pd compound. The unit-cell composition at the solubility limit is Mg₃₄₄₍₂₎Pd₁₂₍₁₎Ni₃₆₍₁₎ with 75% of Ni atoms substituting Pd ones. Ni substitution occurs on the three crystallographic sites exclusively occupied by Pd in Mg₆Pd. The substitution is not fully random. Ni atoms have a slight preference for site with low coordination number. The results reported here enlarge the compositional range in which Mg₆(Pd,Ni) compounds can be used as reversible hydrogen storage materials.     

The evolution of octahedral rotations of orthorhombic LaVO3 in superlattices with cubic SrVO3

We have studied the octahedral rotations in LaVO₃/SrVO₃ superlattices, keeping the thickness of the orthorhombic LaVO₃ layers constant and increasing the thickness of cubic SrVO₃ layers. We have found that for a small thickness of SrVO₃, the octahedral rotations in LaVO₃ are maintained, while for an increasing thickness, these rotations are suppressed. This observation cannot be explained by purely elastic effects due to the lattice mismatch between the two materials, but the absence of rotations in SrVO₃ is a crucial ingredient, illustrating the concept of interface engineering of octahedral rotations.     

Room temperature stable structures and phase transition of Na2Al2B2O7

By Rietveld refinement of the X-ray diffraction (XRD) data of powdered Na₂Al₂B₂O₇ samples aged for over 3 months, we found that Na₂Al₂B₂O₇ at room temperature is a mixture of two phases with space group and P6₃/m, respectively. The structures of the two phases can be refined with identical cell parameters of a=4.80760(11) Å, c=15.2684(5) Å and are composed by [Al₂B₂O₇]²⁻_∝ double layers stacking alternatively with Na⁺ ions along the c-direction, but differ at in-plane bond orientations of the BO₃/AlO₄ groups within the double layers: in P6₃/m phase B-O₁/Al-O₁ bonds of the two layers are perfectly aligned, whereas in phase they are twisted by 46.4/41.6° around c-axis against each other. It is also found that a freshly prepared sample contains only the phase, but part of the phase will transfer to P6₃/m phase slowly at room temperature and the transition can be reversed by heating the aged sample above 220 °C.     

Crystal chemistry of layered carbide, Ti3(Si0.43Ge0.57)C2

 The crystal structure of a layered ternary carbide, Ti₃(Si_0.43Ge_0.57)C₂, was studied with single-crystal X-ray diffraction. The compound has a hexagonal symmetry with space group P6₃/mmc and unit-cell parameters a=3.0823(1) Å, c=17.7702(6) Å, and V=146.21(1) Å³. The Si and Ge atoms in the structure occupy the same crystallographic site surrounded by six Ti atoms at an average distance of 2.7219 Å, and the C atoms are octahedrally coordinated by two types of symmetrically distinct Ti atoms, with an average C-Ti distance of 2.1429 Å. The atomic displacement parameters for C and Ti are relatively isotropic, whereas those for A (=0.43Si+0.57Ge) are appreciably anisotropic, with U₁₁ (=U₂₂) being about three times greater than U₃₃. Compared to Ti₃SiC₂, the substitution of Ge for Si results in an increase in both A-Ti and C-Ti bond distances. An electron density analysis based on the refined structure shows that each A atom is bonded to 6Ti atoms as well as to its 6 nearest neighbor A site atoms, whether the site is occupied by Si or Ge, suggesting that these bond paths may be significantly involved with electron transport properties.     

Synthesis of ZnFe2O4 nanocrystallites by mechanochemical reaction

Mechanochemical reaction of ZnO and α-Fe₂O₃ in a planetary mill formed an amorphous precursor, which was subsequently heated to successfully produce zinc ferrite (ZnFe₂O₄) nanocrystallites. The amorphous precursor and nanocrystallites were characterized by differential thermal analysis (DTA), thermogravimetric analysis (TGA), X-ray diffraction (XRD) and transmission electron microscopy (TEM). Calcination of the precursor powder at 600 °C led to the formation of ZnFe₂O₄ nanocrystallites of about 22 nm in crystal size, and most of particle was about 10-50 nm in diameter. Effect of calcination temperature on the crystal size of the nanoparticles was investigated. The mechanism of nanocrystallite growth was primarily investigated. The activation energy of ZnFe₂O₄ nanocrystallite formation during thermal treatment was calculated to be 18.5 kJ/mol.     

Synthesis of Cu2ZnSnSe4 compound powders by solid state reaction using elemental powders

The solid state reaction method was used to synthesize single phase and near stoichiometric Cu₂ZnSnSe₄ compound from elemental Cu, Zn, Sn and Se powders in a quartz tube furnace under an Ar flow at atmospheric pressure. These elemental powders were initially milled using zirconia balls. The α-CuSe phase was present in all of the milled powders because of the mechanical alloying effect between the Cu and Se powders. The solid state reaction mechanism was examined for the synthesis process. The phase analysis suggested that the Cu₂ZnSnSe₄ powder crystallized into the stannite phase with a high degree of crystallinity after near stoichiometric molar ratios of the powders was reacted at 500 °C for 6 h. This study showed that the solid state reaction method was a straightforward technique for the synthesis of the Cu₂ZnSnSe₄ compound powders from the elemental powders.     

Effect of Mn-doping on the electrical properties of Cu2GeSe3

In this work we report the temperature dependence of the resistivity ρ of p-Cu₂GeSe₃ and manganese-doped p-Cu₂GeSe₃ at low temperature. It was found that for a intrinsic sample ρ obeys the Shklovskii-Efros-type variable-range hopping resistivity law in the temperature range from 4 to 63 K. This behaviour is governed by generation of a Coulomb gap Δ=78 meV in the density of localized states. We find a low activation term T₀=0.24 K, which is an indication of a large localization length ξ. For Mn-doped sample a metal-insulator transition (MIT) is observed at T=65 K. On the basis of the Mott criterion for metal-insulator transition, the critical carrier density n_c is determined. From the analysis of resistivity data it is concluded that Mn acts as acceptor impurity.     

Low-temperature sintering and microwave dielectric properties of Ca2Zn4Ti15O36 ceramics

The sintering behavior, microstructures, and microwave dielectric properties of Ca₂Zn₄Ti₁₅O₃₆ ceramics with B₂O₃ addition were investigated. The crystalline phases and microstructures of Ca₂Zn₄Ti₁₅O₃₆ ceramics with 0-10 wt% B₂O₃ addition were studied by X-ray diffraction (XRD), scanning electron microscopy (SEM), and energy-dispersive X-ray spectroscopy (EDS). The sintering temperature of Ca₂Zn₄Ti₁₅O₃₆ ceramic was lowered from 1170 to 930 °C by 10 wt% B₂O₃ addition. Ca₂Zn₄Ti₁₅O₃₆ ceramics with 8 wt% B₂O₃ addition sintered at 990 °C for 2 h exhibited good microwave dielectric properties, i.e., a quality factor (Qf) 11,400 GHz, a relative dielectric constant (ε_r) 41.5, and a temperature coefficient of resonant frequency (τ_f) 94.4 ppm/°C.     

Synthesis and laser patterning of Bi-doped Y3Fe5O12 crystals in germanosilicate glasses

New germanosilicate glasses giving the crystallization of yttrium iron garnet Y₃Fe₅O₁₂ (YIG) and Bi-doped YIG, 23Na₂O-xBi₂O₃-(12−x)Y₂O₃-25Fe₂O₃-20SiO₂-20GeO₂ (mol%), are developed, and the laser-induced crystallization technique is applied to the glasses to pattern YIG and Bi-doped YIG crystals on the glass surface. It is clarified from the Mössbauer effect measurements that iron ions in the glasses are present mainly as Fe³⁺. It is suggested from the X-ray diffraction analyses and magnetization measurements that Si⁴⁺ ions are incorporated into YIG crystals formed in the crystallization of glasses. The irradiations (laser power: 32-60 mW and laser scanning speed: 7 μm/s) of continuous wave Yb:YVO₄ fiber laser (wavelength: 1080 nm) are found to induce YIG and Bi-doped YIG crystals, indicating that Fe³⁺ ions in the glasses act as suitable transition metal ions for the laser-induced crystallization. It is suggested that YIG and Bi-doped YIG crystals in the laser irradiated part might orient. The present study will be a first step for the patterning of magnetic crystals containing iron ions in glasses.     

Ab initio band structure calculations of the low-temperature phases of Ag2Se, Ag2Te and Ag3AuSe2

Ab initio band structure calculations were performed for the low-temperature modifications of the silver chalcogenides β-Ag₂Se, β-Ag₂Te and the ternary compound β-Ag₃AuSe₂ by the local spherical wave (LSW) method. Coordinates of the atoms of β-Ag₂Se and β-Ag₃AuSe₂ were obtained from refinements using X-ray powder data. The structures are characterized by three, four and five coordinations of silver by the chalcogen, a linear coordination of gold by Se, and by metal-metal distances only slightly larger than in the metals. The band structure calculations show that β-Ag₃AuSe₂ is a semiconductor, while β-Ag₂Se and β-Ag₂Te are semimetals with an overlap of about 0.1-0.2 eV. The Ag 4d and Au 5d states are strongly hybridized with the chalcogen p states all over the valence bands. β-Ag₂Se and β-Ag₂Te have a very low DOS in the energy range from about −0.1 to +0.5 eV. The calculated effective mass β-Ag₂Se is about 0.1-0.3 m_e for electrons and 0.75 m_e for holes, respectively.     

Tunable luminescent properties by adjusting the Sr/Ba ratio in Sr1.97−xBaxMgSi2O7:Eu0.01, Dy0.02 phosphors

The long afterglow phosphors Sr_1.97−xBa_xMgSi₂O₇:Eu²⁺_0.01, Dy³⁺_0.02 (x=0, 0.4, 0.8, 1.2, 1.6 and 1.97) were synthesized via high temperature solid-state reaction. The phase identification reveals that the crystal plane spacing becomes greater with the decrease in the Sr/Ba ratio. Phase transition occurs when x=1.97. A nonlinear relationship between the emission peak and the crystal plane spacing is obtained with the decrease of the Sr/Ba ratio. This ascribes to the splitting of the 5d level of the Eu²⁺ and the change of the crystal field strength. The duration of the afterglow becomes shorter with the decrease of the Sr/Ba ratio. It may ascribe to deeper trap depth, lower trap concentration and the embarrassment of the transfer of carriers.     

Controlled growth of Cu2S hexagonal microdisks and their optical properties

Chalcocite Cu₂S particles have been prepared hydro- and solvo-thermally from a copper plate in pure water, mixed solvents of water and ethylenediamine (en), and pure en, respectively. Their structural and optical properties have been characterized by a combination of powder X-ray diffraction, scanning and transmission electron microscopy (SEM and TEM), and VIS-NIR diffuse reflectance spectroscopy. Their growth and optical properties were found to be highly dependent on synthesis conditions and in particular the en/water volume ratio. For the first time, Cu₂S particles wish the shape of hexagonal microdisks were synthesized in a mild hydrothermal condition and these crystalline particles were found to exhibit unique optical properties.