掺铟氧化锌纳米盘的制备、结构及性质研究

热蒸发Zn、In₂O₃和C粉混合物, 在没有催化剂的条件下制备出掺铟氧化锌纳米盘. 纳米盘呈六边形或十二边形, 均是结晶完好的纤锌矿结构的单晶, 对角线长度约1~3 μm , 厚度40~100 nm. 纳米盘的生长是由自催化固-液-气(V-L-S)机理控制, 在实验条件下Zn和In的液滴抑制纳米盘 [0001]方向的生长. EDS分析表明, 六边形纳米盘和十二边形纳米盘中In的含量相近, 约为2.2%. 室温光致发光谱显示掺杂后的紫外发射峰位稍有蓝移, 同时半高宽(HWHM)变大, 没有观察到绿光发射峰位.     

Fabrication and Visible Light Photocatalytic Activity of Co-doped ZnO Nanorods

Co-doped ZnO nanorods were prepared by electrochemical deposition method in aqueous solution. lb study the as-grown samples, several characterizations were carried out. The scanning electron microscopy（SEM） images show that the samples present a rod-like shape with hexagonal cross sections and roughened surthce. There is a slight shift for （002） diffraction peak of Co-doped ZnO nanorods in XRD because Co2~ ions entered into the ZnO lattice. Energy-dispersive X-ray spectroscopy（EDS） and X-ray photoelectron spectroscopy（XPS） results also show the exist of Co in the sample. Photoluminescence（PL） spectra of the samples were observed at room tempera- ture, the UV emission of Co-doped ZnO shows a slight red shift compared with that of undoped ZnO. Thus, we can reach the conclusion that Zn2＋ ions have been substituted by Co2. ions in the ZnO samples. In addition, photocatalysis property of Co-doped ZnO nanorods was investigated under the irradiation of visible light. It was found that the degradation rate of methyl orange is increased greatly nanorods. by Co-doped ZnO nanorods in comparison to undoped ZnO     

Polyvinylpyrrolidone-assisted growth and optical properties of ZnO hexagonal bilayer disk-like microstructures

ZnO hexagonal bilayer disk-like microstructures are successfully prepared assisted with polyvinylpyrrolidone (PVP), and the photoluminescence (PL) spectrum of as-prepared ZnO samples showed a very strong ultraviolet (UV) emission at the UV region.     

Nano 5% Fe–ZnO: A highly efficient and recyclable heterogeneous solid nano catalyst for the Biginelli reaction

In this paper, we report the synthesis and catalytic application of 5% Fe–ZnO nanocatalyst for the synthesis of 3,4-dihydropyrimidin-2-one derivatives as a highly efficient heterogeneous nanocatalyst. The structural and morphological features of the synthesized nanocatalysts were investigated by X-ray diffraction (XRD) and scanning electron microscopy (SEM). Using Debye-Scherer's formula, the average particle size for undoped ZnO was calculated to be 24.55 nm, while the average particle size for 5% Fe–ZnO was calculated to be 22.37 nm. The high resolution transmission electron microscopy (HR-TEM) revealed a hexagonal crystal lattice type. The Brunauer–Emmett–Teller (BET) surface area of ZnO and 5% Fe–ZnO was found to be 56.50 m²/g and 72.65 m²/g, respectively. Energy Dispersive X-Ray Analysis (EDX) confirmed the elemental composition of undoped ZnO and doped 5% Fe–ZnO nanocatalysts. Biginelli products were produced using a one-pot three-component reaction of urea, β-dicarbonyl compound, and various aromatic aldehydes using 5% Fe–ZnO under clean conditions. It was found that a 5% Fe–ZnO nanocatalyst is a highly efficient heterogeneous nanocatalyst for the synthesis of 3,4-dihydropirimidinones. ¹H NMR and ¹³C NMR analysis was used to confirm the structure of the synthesized Biginelli adducts. This synthetic protocol offers several advantages, including a short reaction time and purity of the synthesized, reusability and ease of catalyst separation, and a clean and quick workup.     

Improvement of glass ionomer restoration by adding ZnO nanoparticles prepared by laser in (Vitro study)

The technique of pulsed laser ablation in liquid media was successfully used to prepare zinc oxide ZnO nanoparticles NPs to enhance glass ionomer GI restorative. The synthesized ZnO NPs were confirmed using UV–Visible spectroscopy, XRD, and TEM. The absorption spectra revealed that the absorbance intensity of the prepared ZnO NPs increased as the number of laser pulses increased, with an absorbance peak at 230 nm due to quantum confinement. The crystalline nature of NPs with hexagonal structure is revealed by XRD analysis. The TEM images demonstrated the nanorod shape with a length of about 3.33 nm and there were spherical nanoparticles ranging from 5 nm to 30 nm. ZnO NPs with and without GI were tested for antibacterial activity against Streptococcus mutans bacteria, which shows slight improvement after adding ZnO NPs to glass ionomer as a result of containing effective ingredients in its composition. The agar well diffusion method results revealed that ZnO with GI had a higher antibacterial activity compared with pure ZnO NPs. Finally, the compressive strength test illustrated significant enhancement of up to 50% associated with the ZnO NP's concentration increase.     

均匀沉淀法制备氧化锌纳米棒

采用均匀沉淀法制备了氧化锌纳米棒,用XRD,TEM,PL等检测手段对样品进行了表征.结果表明:所得样品为长约100 nm,宽约30 nm的纤锌矿结构氧化锌纳米棒,颗粒分布均匀.其在可见光区比紫外区的荧光发射显著增强.     

Precursor-induced hydrothermal synthesis of flowerlike cupped-end microrod bundles of ZnO

Flowerlike cupped-end ZnO microrod bundles have been hydrothermally synthesized from precursor ZnCl2(N2H4)2 in sheet shape at 140 degrees C for 12 h; under the same conditions using the same precursor in rod shape, uniform ZnO nanorods were obtained. XRD pattern indicated the sample is ZnO with hexagonal cell contants a = 3.251 A and c = 5.206 A. FE-SEM and TEM show the formation process of the ZnO sample. HRTEM revealed that the flowerlike cupped-end ZnO microrod bundles grow along the [101] axis. The UV emission peak at approximately 396 nm and the blue band emission peak at approximately 469 nm were observed by PL spectra. A possible formation mechanism was proposed.     

Various shaped-ZnO nanocrystals via low temperature synthetic methods: Surfactant and pH dependence

ZnO nanocrystals, rod-, carnation-, and flower-like structures, have been synthesized in a high yield through low-temperature synthetic methods. Well-aligned ZnO nanorods having hexagonal wurtzite structure were grown on the ZnO thin films assembled by a spin-coating method. The morphologies of ZnO seed films are affected by pHs of sol–gel solutions, resulting smaller sizes and homogeneous roughness at higher pHs and higher number of spin-coating times. The carnation-like structures, average size of about 2–3 μm, were assembled by tens of uniform ZnO nanosheet petals of ∼50 nm in thickness when a different volume ratio of the precursory solution was used. ZnO nanocrystals on the facets of the compact ZnO nanorods have grown to linear nanorods having an average diameter of ∼500 nm and length of ∼2 μm. Furthermore, a noticeable difference in the growth of ZnO nanocrystals in the presence of various surfactants, polyvinylpyrrolidone, polyvinylsulphonic acid, and polyethyleneimine, has been observed and discussed.     

Co掺杂ZnO纳米棒的水热法制备及其光致发光性能

以Zn(NO3)2·6H2O 和Co(NO3)2·6H2O为原料, 通过水热法在较低温度下制备了纯ZnO和Co掺杂的ZnO(ZnO:Co)纳米棒. 利用XRD、EDS、TEM和HRTEM对样品进行了表征, 结合光致发光(PL)谱研究了样品的PL性能. 结果表明, 水热法制备纯ZnO和ZnO:Co纳米棒均具有较好的结晶度. Co2+是以替代的形式进入ZnO晶格, 掺入量为2%(原子分数)左右. 纯的ZnO纳米棒平均直径约为20 nm, 平均长度约为180 nm; 掺杂样品的平均直径值约为15 nm, 平均长度约为200 nm左右; Co掺杂轻微地影响ZnO纳米棒的生长. 另外, Co掺杂能够调整ZnO纳米棒的能带结构、提高表面态含量, 进而使得ZnO:Co纳米棒的紫外发光峰位红移, 可见光发光能力增强.     

Preparation, characterization and photocatalytic performance of Mo-doped ZnO photocatalysts

A series of Mo-doped ZnO photocatalysts with different Mo-dopant concentrations have been prepared by a grinding-calcination method.The structure of these photocatalysts was characterized by a variety of methods,including N 2 physical adsorption,X-ray diffraction(XRD),scanning electron microscopy(SEM),Fourier transform infrared(FT-IR) spectroscopy,photoluminescence(PL) emission spectroscopy,and UV-vis diffuse reflectance spectroscopy(DRS).It was found that Mo 6+ could enter into the crystal lattice of ZnO due to the radius of Mo 6+(0.065 nm) being smaller than that of Zn 2+(0.083 nm).XRD results indicated that Mo 6+ suppressed the growth of ZnO crystals.The FT-IR spectroscopy results showed that the ZnO with 2 wt.% Mo-doping has a higher level of surface hydroxyl groups than pure ZnO.PL spectroscopy indicated that ZnO with 2 wt.% Mo-doping also exhibited the largest reduction in the intensity of the emission peak at 390 nm caused by the recombination of photogenerated hole-electron pairs.The activities of the Mo-doped ZnO photocatalysts were investigated in the photocatalytic degradation of acid orange II under UV light(λ = 365 nm) irradiation.It was found that ZnO with 2 wt.% Mo-doping showed much higher photocatalytic activity and stability than pure ZnO.The high photocatalytic performance of the Mo-doped ZnO can be attributed to a great improvement in the surface properties of ZnO,higher crystallinity and lower recombination rate of photogenerated hole-electron(e-/h+) pairs.Moreover,the undoped Mo species may exist in the form of MoO3 and form MoO3 /ZnO heterojunctions which further favors the separation of e-/h+ pairs.     

高度取向ZnO单晶亚微米棒阵列的制备与表征

通过低温压热的方法,在经过预先处理长满晶核的SnO2导电玻璃基底上制备出具有高度取向的ZnO亚微米棒阵列.用扫描电子显微镜(SEM)、选区电子衍射(SAED)及X射线粉末衍射(XRD),对制备出的ZnO亚微米棒的结构和形貌进行了表征.SEM测试结果表明,ZnO亚微米棒是六方型的,近乎垂直地长在基底上,棒的直径为400～500 nm,长度约为2 μm. SAED和XRD结果表明,ZnO亚微米棒为单晶,属于六方晶系,并且沿[001]方向择优取向生长.     

加热覆盖有ZnCl2溶液的锌片制备ZnO亚微米棒阵列

将表面覆盖有ZnCl2溶液的锌片加热到400 ℃反应1 h, 在锌片上生长出了ZnO亚微米棒阵列. 采用扫描电镜、透射电子显微镜和X射线衍射仪对所制备的产物进行了表征和分析. 结果表明产物为六方相纤锌矿单晶结构的ZnO亚微米棒, 其直径和长度分别为300～650 nm和6 μm, 提出了ZnO亚微米棒可能的生长机理. 在波长为300 nm光的激发下, 发现了ZnO亚微米棒阵列具有发光峰位于395 nm强的紫外光发光和位于490 nm弱的蓝绿光发光, 这两种发光分别起源于ZnO宽带隙带边发射和ZnO中相应的缺陷结构.     

Structures and optical properties of Zn1?x Ni x O nanoparticles by coprecipitation method

Nanocrystals of undoped and nickel-doped zinc oxide (Zn_1?x Ni _x O, where x?=?0.00?C0.05) were synthesized by the coprecipitation method. Crystalline size, morphology, and optical absorption of prepared samples were determined by X-ray diffraction (XRD), transmission electron microscope (TEM), scanning electron microscope (SEM), and UV?Cvisible spectrometer. XRD and SEM studies revealed that Ni-doped ZnO crystallized in hexagonal wurtzite structure. Doping of ZnO with Ni²⁺ was intended to enhance the surface defects of ZnO. The incorporation of Ni²⁺ in place of Zn²⁺ provoked an increase in the size of nanocrystals as compared to undoped ZnO. Crystalline size of nanocrystals varied from 10 to 40?nm as the calcination temperature increased. Enhancement in the optical absorption of Ni-doped ZnO indicated that it can be used as an efficient photocatalyst under visible light irradiation. Optical absorption measurements indicated a red shift in the absorption band edge upon Ni doping. The band gap value of prepared undoped and Ni-doped ZnO nanoparticles decreased as annealing temperature was increased up to 800?°C.     

Room temperature ferromagnetism in undoped and Fe doped ZnO nanorods: Microwave-assisted synthesis

One-dimensional (1D) undoped and Fe doped ZnO nanorods of average length ∼1 μm and diameter ∼50 nm have been obtained using a microwave-assisted synthesis. The magnetization (M) and coercivity (H_c) value obtained for undoped ZnO nanorods at room temperature is ∼5×10⁻³ emu/g and ∼150 Oe, respectively. The Fe doped ZnO samples show significant changes in M -H loop with increasing doping concentration. Both undoped and Fe doped ZnO nanorods exhibit a Curie transition temperature (T_c) above 390 K. Electron spin resonance and Mössbauer spectra indicate the presence of ferric ions. The origin of ferromagnetism in undoped ZnO nanorods is attributed to localized electron spin moments resulting from surface defects/vacancies, where as in Fe doped samples is explained by F center exchange mechanism.     

Effect of Doped Boron on the Properties of ZnO Thin Films Prepared by Sol-gel Spin Coating

Transparent conductive boron-doped ZnO thin films were prepared by sol-gel spin coating method. The effect of doped boron concentration on the properties of the films was systematically discussed. The films were characterized by X-ray diffraction, atomic force microscopy, spectrophotometry, and Hall effect measurement system. All the doped and undoped ZnO films were of a single hexagonal structure, and showed a preferred orientation of （002）. The particle size and surface roughness of the films decreased with increased doped boron concentration. All the films exhibited an average transmittance of approximate 90% in visible-light region and an energy gap of about 3.3 cV. The maximum carrier concentration, the highest carrier mobility and the lowest resistivity were observed at a doped boron concentration of 0.5%（molar fraction）. Based on these results, we suggested that the saturation concentration of doped boron in ZnO film is 0.5%（molar fraction）.     

碱式硫酸锌转化法制备ZnO多孔片及其光致发光性能

采用化学浴沉积法制备了碱式硫酸锌(ZSH)纳米片, 并经1000 ℃煅烧处理得到了ZnO多孔片. 详细研究了ZSH在Zn²⁺-六亚甲基四胺前驱体溶液体系中的形成机理、ZSH 的热解过程、ZnO的结晶性、微结构以及光致发光性能. 结果表明, 所得ZnO多孔片呈规则六角形状, 其尺寸为10-50 μm, 厚度为200-500 nm, 由于高温固相反应中传质等因素的限制, 构成薄片的ZnO晶粒呈多边形或不规则形貌, 晶粒间的孔为亚微米孔, 尺寸在100-500 nm范围. ZnO多孔薄片结晶性良好, 在388 nm处表现出较强紫外发光, 无可见光区的缺陷发光. 机理分析表明, SO₄^2- 与Zn²⁺的高亲和力是Zn²⁺-六亚甲基四胺体系中ZSH生成的根本原因, 而ZSH的热分解过程对ZnO多孔片的形貌和微结构影响显著. 本研究提出了一种制备高结晶质量ZnO多孔材料的新方法, 所得ZnO多孔片可望在催化、染料敏化太阳能电池、紫外光电器件等领域得到应用.     

Sn掺杂ZnO半导体纳米带的制备、结构和性能

在无催化剂的条件下, 利用碳热还原反应气相沉积法制备出了高产率单晶Sn掺杂ZnO纳米带. XRD和TEM研究表明纳米带为结晶完好的纤锌矿结构, 生长方向沿[0001], EDS分析表明纳米带中Sn元素含量约为1.9%. 室温光致发光谱(PL)显示掺锡氧化锌纳米带存在强的绿光发射峰和较弱的紫外发射峰, 谱峰峰位中心分别位于494.8 nm和398.4 nm处, 并对发光机制进行了分析. 这种掺杂纳米带有望作为理想的结构单元应用于纳米尺度光电器件领域.     

Synthesis and Optical Properties of Ce-doped ZnO

ZnO nanorods were synthesized using the sol-gel method, and the effects of annealing temperature and Ce doping on the morphologies and optical properties of ZnO nanostructures were investigated in detail. The XRD measurements showed that the as-synthesized ZnO nanostructures had a hexagonal wurtzite structure. SEM images showed that uniform nanorods formed at 900 °C. Photoluminescence measurements showed an ultraviolet emission peak and a relatively broad visible light emission peak for the samples sintered at different temperatures. The UV emission peak bathochromically shifted when the annealing temperature rose from 850 to 1000 °C. Ce doping decreased the synthesized temperature of the ZnO nanorods to 500 °C, and the UV peaks hypsochromically shifted.     

Synthesis of europium-doped zinc oxide micro- and nanowires

Single crystalline Eu³⁺-doped wurtzite ZnO micro- and nanowires were synthesized by a chemical vapor deposition method (CVD). The nanostructures were grown by autocatalytic mechanism at walls of an alumina boat. The structure and properties of the doped ZnO is fully characterized by X-ray diffraction (XRD), energy-dispersive X-ray spectrometry (EDX), scanning and transmission electron microscopy (SEM and TEM), and photoluminescence (PL) methods. The synthesis was carried out for 10 min giving vertically aligned nanowires with mean diameter of 50–400 nm and with length of up to several microns. The nanowires were grown along ±[0001] direction. The concentration of Eu³⁺ dopant in the synthesized nanowires was varied from 0.7 to 0.9 at %. The crystal structure and microstructures of the doped nanomaterials were discussed and compared with undoped ZnO. The photoluminescence spectra show that emission of doped samples were shifted towards orange-red region (2.02 eV) relative to undoped zinc oxide nanostructures (2.37 eV) due to Eu³⁺ intraionic transitions from ZnO/Eu.     

Sn掺杂ZnO纳米针的结构及其生长机制(英文)

利用包括磁控溅射和热氧化的两步法在Si(111)衬底上制备了Sn掺杂ZnO纳米针.首先用磁控溅射法在Si(111)衬底上制备Sn:Zn薄膜,然后在650℃的Ar气氛中对薄膜进行热氧化,制备出Sn掺杂ZnO纳米针.样品的结构、成分和光学性质采用X射线衍射(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)、高分辨透射电子显微镜(HRTEM)、能量散射X射线(EDX)谱和光致发光(PL)光谱等技术手段进行分析.结果表明,制备的样品为具有六方纤锌矿结构的单晶Sn掺杂ZnO纳米针,Sn掺杂量为2.5%(x,原子比),底部和头部直径分别为200-500 nm和40 nm,长度为1-3μm,结晶质量较高.室温光致发光光谱显示紫外发光峰比纯ZnO的发光峰稍有蓝移,这可归因于能谱分析中探测到的Sn的影响.基于本实验的实际条件,简单探讨了Sn掺杂ZnO纳米针的生长机制.