Simultaneous electrochemical determination of xanthine and uric acid at a nanoparticle film electrode

A sensitive electrochemical method was developed for simultaneous determination of uric acid (UA) and xanthine (XA) at a glassy carbon electrode modified with multi-wall carbon nanotubes (MWNTs) film. The oxidation peak currents of UA and XA were increased at the MWNTs film electrode significantly. The experimental parameters, which influence the peak currents of UA and XA, such as the amount of MWNTs on the glassy carbon electrode, the pH of the solution, accumulation time, and scan rate, were optimized. Under optimum conditions, the peak currents were linear to the concentration of UA over the wide range from 1 x 10(-7) mol L(-1) to 1 x 10(-4) mol L(-1) and to that of XA over the wide range from 2 x 10(-8) mol L(-1) to 2 x 10(-5) mol L(-1). The interferences studies showed that the MWNTs-modified electrode exhibited excellent selectivity in the presence of ascorbic acid, dopamine, and hypoxanthine. The proposed procedure was successfully applied to detect UA and XA in human serum without any preliminary treatment.     

Voltammetric determination of tyrosine based on an L-serine polymer film electrode

A novel film electrode for the voltammetric determination of tyrosine has been constructed based on electropolymerization of L-serine on a glassy carbon electrode. Voltammetric behaviour of tyrosine on the poly-L-serine film electrode was investigated with cyclic voltammetry and linear sweep voltammetry, and electrochemical parameters were calculated from chronocoulometry. In optimal conditions, the oxidation peak current of tyrosine on the poly-L-serine film electrode was enhanced greatly. A sensitive oxidation peak at 0.90 V was employed to determine tyrosine. A linearity between the oxidation peak current and the tyrosine concentration was obtained in the range of 3.0 x 10(-7) to 1.0 x 10(-4) mol L(-1) with a detection limit of 1.0 x 10(-7)mol L(-1). The practical application of the film electrode in the determination of tyrosine in a commercial amino acid oral solution demonstrated that it has good selectivity and high sensitivity.     

Electrochemical determination of methimazole based on the acetylene black/chitosan film electrode and its application to rat serum samples

A novel method has been developed for the determination of methimazole, which was based on the enhanced electrochemical response of methimazole at the acetylene black/chitosan composite film modified glassy carbon electrode. The electrochemical behavior of methimazole was studied at this film electrode by cyclic voltammetry and differential pulse voltammetry. The experimental results showed that methimazole exhibited a remarkable oxidation peak at 0.63V at the film electrode. Compared with the bare glassy carbon electrode, the oxidation peak current increased greatly, and the peak potential shifted negatively, which indicated that the acetylene black/chitosan film electrode had good catalysis to the electrochemical oxidation of methimazole. The enhanced oxidation current of methimazole was indebted to the nano-porus structure of the composite film and the enlarged effective electrode area. The influences of some experimental conditions on the oxidation of methimazole were tested and the calibration plot was examined. The results indicated that the differential pulse response of methimazole was linear with its concentration in the range of 1.0×10(-7) to 2.0×10(-5)mol/L with a linear coefficient of 0.998, and in the range of 4.0×10(-5) to 3.0×10(-4)mol/L with a linear coefficient of 0.993. The detection limit was 2.0×10(-8)mol/L (S/N=3). The film electrode was used to detect the content of methimazole in rat serum samples by the standard addition method with satisfactory results.     

Diffusion coefficient measurements in microfluidic devices

A glassy carbon electrode (GCE) modified with Pd/IrO(2) provides excellent electrocatalytic oxidation of hydrogen peroxide. Glucose oxidase (GOD) and xanthine oxidase (XOD) were co-immobilized on the modified electrode with a thin film Nafion coated on the enzyme layer to form a glucose (Glu)/hypoxanthine (Hx) sensor, without interference from electroactive species such as ascorbic acid (AA) and uric acid (UA). Its response was evaluated with respect to the enzyme amount on the electrode, pH and temperature of the electrolyte. The prepared bienzymic biosensor, used as the detector of HPLC gave a detection limit of 1.0x10(-6) mol l(-1) Glu and 2.0x10(-7) mol l(-1) Hx (Hx) with a linear concentration range of 5.0x10(-6)-2.5x10(-3) mol l(-1) and 1.0x10(-6)-5.0x10(-4) mol l(-1), respectively. Coupled with microdialysis, it was used to monitor the concentrations of Glu and Hx in rat brain.     

Amperometric determination of glutathione and cysteine on a Pd-IrO(2) modified electrode with high performance liquid chromatography in rat brain microdialysate

A Pd/IrO(2) co-electrodeposited glassy carbon electrode was prepared and the electrochemical behavior of glutathione (GSH) at this chemically modified electrode (CME) has been studied by cyclic voltammetry (CV). The results indicated that the modified electrode efficiently exhibited electrocatalytic oxidation for GSH with relatively high sensitivity, stability, and long-life. Coupled with high-performance liquid chromatography (HPLC), the Pd/IrO(2) modified electrode was utilized for the electrochemical detection (ECD) of the thiocompounds, glutathione and cysteine (Cys). The peak currents were linear with the substance concentrations in the range of 1.0 x 10(-5) mol L(-1) to 8.0 x 10(-4) mol L(-1) for GSH and 4.0 x 10(-6) mol L(-1) to 2.0 x 10(-4) mol L(-1) for Cys. The detection limits were 2.0 x 10(-6) mol L(-1) for GSH and 5.0 x 10(-7) mol L(-1) for Cys with S/N of 3. The method has been successfully applied to assess the contents of GSH and Cys in rat brain microdialysates.     

一步电沉积纳米铜/石墨烯/壳聚糖复合膜修饰玻碳电极测定邻苯二酚

用一步电沉积法制备了纳米铜/石墨烯/壳聚糖复合膜修饰玻碳电极。用循环伏安法(CV)和差分脉冲伏安法(DPV)对邻苯二酚在该修饰电极的电化学行为进行了研究。实验结果表明,在pH值为7.0的磷酸盐缓冲液(PBS)中,该修饰电极对邻苯二酚具有良好的电催化作用,其电化学信号与邻苯二酚的浓度在1.0×10-6～2.0×10-4mol/L范围内呈良好的线性关系,线性相关系数为0.991。检出限为1×10-7mol/L。结果表明,纳米铜/石墨烯/壳聚糖复合膜修饰电极显著提高了邻苯二酚的电化学响应信号,并表现出良好的选择性和重现性。该方法成功用于水样中邻苯二酚含量的测定。     

纳米金/3-氨丙基-三乙氧基硅烷修饰传感器电化学检测NO-2

将3-氨丙基-三乙氧基硅烷（ATS）修饰在玻碳电极表面,再自组装一层纳米金,制备了一种新型NO2^-的电化学传感器。该修饰电极对NO2^-有较好的催化作用。在pH为3时,NO2^-的氧化峰电流与其浓度在5．0×10^-7～1．0×10^-3mol／L范围内呈良好的线性关系,检出限可达2．0×10^-7mol／L。方法具有较高的灵敏度和较好的重现性。     

维生素B6在纳米金/石墨烯修饰电极上的电化学行为

将金纳米粒子电沉积在石墨烯修饰的玻碳电极表面,研究了维生素B6(VB6)在该修饰电极上的电化学行为。扫描电镜用于该修饰电极组装过程的形貌表征。实验结果表明:VB6在此修饰电极上出现一个良好的氧化峰,在最佳实验条件下,其氧化峰电流与VB6浓度在5.0×10-8～2.0×10-5 mol/L范围内呈线性关系,其线性回归方程为I(μA)=0.5697c(μmol/L)+0.06275,R=0.9992,检出限为2.0×10-8 mol/L(S/N=3)。一些常见的干扰物质如抗坏血酸不干扰VB6的检测。方法已用于片剂中VB6的含量的检测。     

A multiwall carbon nanotubes film-modified carbon fiber ultramicroelectrode for the determination of nitric oxide radical in liver mitochondria

A novel chemically modified electrode based on the multiwall carbon nanotubes (MWNTs) film-coated carbon fiber ultramicroelectrode (CFUE) has been described for the determination of nitric oxide radical (.NO). The electrochemical behaviors of MWNTs-modified CFUE have been characterized in 0.2 mmol L(-1) K(4)Fe(CN)(6) and 0.1 mol L(-1) KCl solution. The Nafion film was used to avoid some electroactive interferences. The amount of Nafion was optimized, and some possible interferents [such as nitrite (NO(2)(-)), nitrate (NO(3)(-)), ascorbate, dopamine (DA), l-arginine (l-Arg), etc.] were tested and evaluated. The oxidation peak current of .NO increases significantly at the MWNT/Nafion-modified CFUE, in contrast to that at the bare and the Nafion-modified CFUE, and the oxidation peak potential is at 0.78 V (vs. SCE), which can be used for the detection of .NO. The oxidation peak current is linearly with the concentration of .NO from 2x10(-7) to 8.6x10(-5) mol L(-1), and the detection limit is 2x10(-8) mol L(-1). The liver mitochondria in Carassius auratus were isolated and .NO release from mitochondria was monitored by using this ultramicroelectrode system.     

维生素B6在维生素B12修饰电极上的电化学行为及其分析应用

采用循环伏安法研究了维生素B6在维生素B12修饰玻碳电极上的电化学行为,建立了测定痕量维生素B6的新方法.在pH 8.6的NH3-NH4Cl缓冲溶液中,维生素B6在修饰电极上产生一个灵敏的氧化峰,采用差分脉冲伏安法测定,其氧化峰电流与维生素B6的浓度在8.0×10-7～2.0×10-4 mol/L范围内呈良好的线性关系,检出限为2.0×10-7 mol/L.该修饰电极具有良好的选择性、灵敏度及稳定性,用于片剂中维生素B6的定量分析,结果令人满意.     

石墨烯/铁氰化钴复合膜修饰玻碳电极同时测定对苯二酚、邻苯二酚和间苯二酚

采用滴涂法和电沉积法制备了石墨烯/铁氰化钴复合膜修饰玻碳电极. 用扫描电镜对该纳米复合膜进行了表征.用循环伏安法研究了对苯二酚(HQ)、邻苯二酚(CT)和间苯二酚(RS)在修饰电极上的电化学行为. 实验结果表明, 相对于裸玻碳电极和石墨烯修饰电极, HQ, CT 和RS 在石墨烯/铁氰化钴修饰电极上的氧化峰电流显著提高. 利用差分脉冲伏安法测定, HQ, CT 和RS 分别在1.0×10^－6～1.5×10^－4 mol/L, 1.0×10^－6～2.0×10^－4 mol/L 和3.5×10^－6～2.5×10^－4 mol/L浓度范围内与氧化峰电流呈良好的线性关系, 相关系数分别为0.991, 0.993 和0.992. 信噪比为3 时, HQ, CT 和RS 检出限分别为2.0×10^－7, 2.1×10^－7 和3.5×10^－7 mol/L. 将该方法用于水样分析, 回收率为95.6%～106.1%.     

Electrochemical study of bergenin on a poly(4-(2-pyridylazo)-resorcinol) modified glassy carbon electrode and its determination in tablets and urine

A very sensitive electroanalytical method was employed to determine bergenin in phosphate buffer with a pH of 6.0, bergenin was accumulated at a 4-(2-pyridylazo)-resorcinol (PAR) polymer film modified glassy carbon electrode (GCE) surface under the condition of open-circuit. In the following anodic sweep from −0.4 to 0.8 V, bergenin adsorbed at the PAR polymer film modified electrode surface, was oxidized and yielded a sensitive oxidation peak at 0.595 V. Due to its unique structure and extraordinary properties, the PAR polymer film shows higher accumulation efficiency toward bergenin compared with a bare GCE. Hence, the amount of bergenin at the PAR polymer film modified GCE surface increases significantly, and finally the oxidation peak current improves greatly. The experimental conditions, such as supporting electrolyte, pH value, accumulation time and scan rate, were optimized for the measurement of bergenin, and a sensitive electroanalytical method was proposed for bergenin determination. The oxidation peak current varies linearly with the concentration of bergenin over the range of 2.0 × 10⁻⁷ to 1.2 × 10⁻⁵ mol/L, and the detection limit is 2.0 × 10⁻⁸ mol/L after 3 min open-circuit accumulation. The relative standard deviation of the same electrode in 10 successive scans is 1.8% for 1.0 × 10⁻⁶ mol/L bergenin and 2.1% for interelectrodes, indicating excellent reproducibility. This new method was successfully demonstrated with bergenin tablets and diluted urine.     

Sodium dodecyl sulfate-modified carbon paste electrodes for selective determination of dopamine in the presence of ascorbic acid

A carbon paste electrode (CPE) modified by a monolayer film of sodium dodecyl sulfate (SDS) was used for detection of dopamine (DA). Cyclic voltammetry demonstrated improved response of the DA sensor. This suggests the effectivity of surface modification of CPE by SDS. Impedance spectroscopy was used for the characterization of CPE surface properties. The effect of SDS concentration on the electrode quality also reveals that SDS formed a monolayer on CPE surface with a high density of negative-charged end directed outside the electrode. As a result, the carbon paste electrode modified with SDS (SDS/CPE) exerted discrimination against ascorbic acid in physiological circumstance. Thus, it can selectively determine dopamine even in the presence of 220-fold AA combined with differential pulse stripping voltammetry. In pH 7.40 phosphate buffer solution, the oxidation peak current on differential pulse voltammograms increases linearly with the concentration of DA in the range of 5.0 x 10(-7) to 8.0 x 10(-4) mol . L(-1) with a detection limit of 5.0 x 10(-8) mol . L(-1). Satisfying results are achieved when detecting the DA in injection and simulated biology sample.     

聚色氨酸／镍复合膜修饰电极测定抗坏血酸的研究

采用电化学聚合法制备了聚色氨酸／镍复合膜修饰玻碳电极,研究了抗坏血酸在该修饰电极上的电化学行为,建立了测定痕量抗坏血酸的新方法。在pH6．2的磷酸盐缓冲溶液中,抗坏血酸在修饰电极上产生一个灵敏的氧化峰,采用线性扫描伏安法测定,其氧化峰电流与抗坏血酸浓度在2．0×10^-6 -1．0×10^-3mol／L范围内呈良好的线性关系,检出限为5．0×10^-7mol／L。对1．0×10^-4mol／L抗坏血酸溶液平行测定6次,测定结果的相对标准偏差为1．9％。该法用于片剂中抗坏血酸含量的测定,加标回收率为97．8％～101．2％。     

Carbon paste electrode modified with copper(II) phosphate immobilized in a polyester resin for voltammetric determination of <Emphasis Type="SmallCaps"> l </Emphasis>-ascorbic acid in pharmaceutical formulations

A carbon paste electrode modified with copper(II) phosphate immobilized in a polyester resin (CuP-Poly) is proposed for voltammetric determination of L-ascorbic acid in pharmaceutical formulations. The modified electrode allows the detection of L-ascorbic acid at lower anodic potentials than observed at unmodified electrodes. Several parameters that can influence the voltammetric response of the proposed electrode such as carbon paste composition, pH, scan rate, and possible interference were investigated. The peak current was proportional to the concentration of ascorbic acid in the range 2.0 x 10(-5) to 3.2 x 10(-3) mol L(-1) with a detection limit of 1.0 x 10(-5) mol L(-1). The stability and repeatability of the electrode for the determination of L-ascorbic acid are also discussed. Amperometric response was also recorded for electrocatalytic oxidation of the L-ascorbic acid. Concentrations of the vitamin C in pharmaceutical formulations (tablets) measured using the modified electrode and a titrimetric method are in agreement at the 95% confidence level and within an acceptable range of error.     

Direct Electrochemical Oxidation of Dihydronicotiamide AdenineDinucleotide （NADH） at An Ordered Carbon Nanotubes Electrode

With novel structure, extraordinary electronic properties, high chemical stability and extremely high mechanical strength1, carbon nanotubes (CNTs) have found a wide range of potential applications2-6. The subtle electronic properties suggest that CNTs have the ability to promote electron transfer when they are used as an electrode. The disordered CNTs have been used to fabricate electrode7-10. Thus, it is very interesting to fabricate the electrode using the ordered CNTs and to examin…     

A nitric oxide biosensor based on horseradish peroxidase/kieselguhr co-modified pyrolytic graphite electrode

A reagentless nitric oxide (NO) biosensor was prepared using a pyrolytic graphite (PG) electrode modified with a composite film containing horseradish peroxidase (HRP) and kieselguhr. Noticeably, the electron-transfer reactivity of HRP was significantly enhanced when incorporated in the inorganic kieselguhr material. Consequently, we observed the direct electrochemical response of HRP in this composite film, which would be otherwise electrochemically silent (in the absence of kieselguhr). Importantly, this modified electrode demonstrated nice catalytic activity, as well as high stability, towards the reduction of NO. The peak current related to NO was linearly proportional to its concentration from 2.0 x 10(-7) to 2.0 x 10(-5) mol/L, and the relative standard deviation was 4 % for five successive determinations at a NO concentration of 1.0 x 10(-5) mol/L. The critical level in concentration was estimated to be (4.0 +/- 0.3) x 10(-8) mol/L.     

维生素B1的电化学聚合及催化作用

用循环伏安法在石墨电极上制备了VB1聚合膜修饰电极,VB1聚合膜在pH5的PBS中有一对氧化还原峰,峰电位Epd=350mV,Epc=325mV,峰电流与扫描速率的平方根成正比,表明电子在膜中的传递为扩散控制,且聚合膜与VB1单体有不同的电化学性质。实验表明VB1聚合膜对多巴胺、肾上腺素等神经递质有显著的电催化作用。     

Simultaneous determination of uric acid, xanthine and hypoxanthine at poly(pyrocatechol violet)/functionalized multi-walled carbon nanotubes composite film modified electrode

A sensitive and selective electrochemical method was developed for simultaneous determination of uric acid (UA), xanthine (XA) and hypoxanthine (HX) based on a poly (pyrocatechol violet)/carboxyl functionalized multi-walled carbon nanotubes composite film modified electrode. The preparation and basic electrochemical performance of the novel composite film modified glassy carbon electrode were investigated in details. The electrochemical behaviors of UA, XA and HX at the modified electrode were studied by cyclic voltammetry. The results showed that this new electrochemical sensor exhibited excellent electrocatalytic activity towards the oxidation of the three analytes. The mechanism of catalysis was discussed. The anodic peaks of the three species were well defined with lowered oxidation potential and enhanced oxidation peak currents, so the modified electrode was used for simultaneous voltammetric measurement of UA, XA and HX by differential pulse voltammetry. Under the optimum conditions, the detection limits were 0.16 μmol L(-1) for UA, 0.05 μmol L(-1) for XA and 0.20 μmol L(-1) for HX, respectively (S/N of 3). The proposed method has been successfully applied to simultaneous determination of UA, XA and HX in human serum samples.     

对乙酰氨基酚在聚刚果红修饰电极上的伏安测定

应用循环伏安法于玻碳电极修饰聚刚果红薄膜,并研究对乙酰氨基酚(ACOP)在该修饰电极上的电化学行为.实验表明,聚刚果红修饰电极对ACOP具有良好的电催化性能.在2.0×10-7~2.0×10-6mol.L-1ACOP浓度范围内,其差示脉冲伏安峰电流随浓度变化呈良好的线性关系,检测限为4.0×10-8mol.L-1.该法可用于实际样品的含量测定.