预处理对Ni-Co双金属沼气重整催化剂性能与结构的影响

采用过量浸渍法制备了Ni-Co/La₂O₃-γ-Al₂O₃双金属催化剂, 并使用固定床石英反应器在850℃,0.1MPa和空速为6000mL g_cat^-1 h^-1的条件下考察了预处理对催化剂性能的影响. 运用X射线衍射、热重-差示扫描量热、透射电子显微镜、扫描电镜和X射线能谱分析等手段对催化剂进行了表征. 结果表明,与传统氢气还原预处理相比,经氢气和二氧化碳预处理后, 催化剂性能明显提高,且能基本消除该催化剂上沼气重整反应的诱导期. 511 h的稳定性实验结果表明,催化剂经氢气和二氧化碳预处理后具有很好的稳定性和抗积碳性,平均积碳速率仅为0.2 mg g_cat^-1 h^-1. 表征结果显示,经氢气和二氧化碳预处理后,催化剂具有更好的抗烧结和抗积碳性能,反应后金属颗粒较小,分布较均匀,粒径分布范围较窄,从而增强了催化剂的稳定性.     

预处理方法对Ni-Co双金属催化剂性能与结构的影响

浸渍法制备了Ni-Co/La₂O₃-γ-Al₂O₃双金属催化剂, 经氢气还原预处理后, 再分别由一氧化碳、甲烷和二氧化碳进行再次预处理, 考察了预处理方法对该催化剂上沼气重整制氢性能的影响, 并运用X射线衍射(XRD)、热重-差示扫描量热(TG-DSC)、透射电子显微镜(TEM)等手段对催化剂进行了表征. 结果表明, 与传统氢气还原预处理相比, 经氢气与一氧化碳预处理后, 催化剂性能无明显变化; 经氢气与甲烷预处理后, 催化剂性能明显变差; 而经氢气和二氧化碳预处理后, 催化剂性能明显变优, 且能基本消除该催化剂上沼气重整反应的诱导期. 分析结果表明, 经氢气和二氧化碳预处理后, 催化剂中金属颗粒较小, 分布较均匀, 粒径分布范围较窄, 从而减少了催化剂表面碳的沉积, 增强了催化剂的抗积炭性能, 可延长催化剂的使用寿命.     

甲烷二氧化碳重整制合成气镍-钴双金属催化剂

积炭;甲烷二氧化碳重整制合成气镍-钴双金属催化剂     

镍基催化剂催化木醋液重整制氢实验研究

为了实现木醋液的高值化利用,在固定床反应器中,进行木醋液催化重整制氢实验,采用浸渍法制备一系列不同Co添加量的Ni基催化剂,以产氢率、碳转化率、H2选择性和积炭量为主要评价指标,探究液时空速、反应温度、镍钴比等工况对木醋液催化重整制氢的影响,同时采用XRF、H2-TPR、SEM及元素分析等方法对催化剂进行了表征.结果表...     

负载Ni催化剂用于乙二醇蒸汽重整制氢催化性能研究

采用等体积浸渍法和共沉淀法制备了Ni催化剂,在固定床反应器上考察了Ni负载量、焙烧温度、反应温度等因素对乙二醇低温重整制氢反应活性和选择性的影响。应用X射线衍射、氮物理吸附、H₂程序升温还原等技术对负载型Ni催化剂进行了表征。结果表明,共沉淀法制备的Ni/CeO₂催化剂具有较小的NiO颗粒与CeO₂载体颗粒粒径,催化活性较高。添加少量氧化钴到Ni/CeO₂催化剂中可使H₂收率达72.6%,EG转化率达93.1%。在CeO₂中添加Al₂O₃能提高负载Ni催化剂的活性,乙二醇转化率达94.0%,H₂收率达67.0%;但添加SiO₂则使其活性明显变差。     

CO2预处理操作条件对Ni-Co双金属催化剂性能与结构的影响

The performance of the Ni-Co bimetallic catalyst was significantly improved by a novel H₂ and CO₂ (HCD) pretreatment in the dry reforming of methane compared with traditional H₂ pretreatment. The effects of the HCD pretreatment operating conditions, such as pretreatment time, temperature, gas feeding ratio, and gas flow rate, on the catalytic performance of Ni-Co bimetallic catalyst were investigated. The optimal pretreatment time, temperature, gas feeding ratio (CH₄/CO₂), and gas flow rate were 0.5-1 h, 780-800 ℃, 0:10, and 175-200 mL·min^-1, respectively. Biogas was simulated with CH₄ and CO₂ in a volume ratio of 1 and without any other diluted gas. The catalyst was characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), and thermogravimetry (TG) coupled to differential scanning calorimetry (DSC). In a 511 h stability test under the optimized operating conditions, the catalyst pretreated with both H₂ and CO₂ exhibited excellent stability. The average conversions of CH₄ and CO₂, selectivities for H₂ and CO, and volume ratio of H₂/CO were 96%, 97%, 98%, 99%, and 0.98, respectively. The average carbon deposition rate over the Ni-Co bimetallic catalyst was only about 0.2 mg·g^-1·h^-1. The characterization results revealed that the sintering speed of the metal greatly decreased with testing time, and the metal particle will not greatly sinter with further testing time. The amount of deposited carbon on the catalyst gradually decreased and growth of filamentous carbon over the surface of the catalyst could be inhibited. The performance of the Ni-Co bimetallic catalyst was significantly improved by a novel H₂ and CO₂ (HCD) pretreatment in the dry reforming of methane compared with traditional H₂ pretreatment. The effects of the HCD pretreatment operating conditions, such as pretreatment time, temperature, gas feeding ratio, and gas flow rate, on the catalytic performance of Ni-Co bimetallic catalyst were investigated. The optimal pretreatment time, temperature, gas feeding ratio (CH₄/CO₂), and gas flow rate were 0.5-1 h, 780-800 ℃, 0:10, and 175-200 mL·min^-1, respectively. Biogas was simulated with CH₄ and CO₂ in a volume ratio of 1 and without any other diluted gas. The catalyst was characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), and thermogravimetry (TG) coupled to differential scanning calorimetry (DSC). In a 511 h stability test under the optimized operating conditions, the catalyst pretreated with both H₂ and CO₂ exhibited excellent stability. The average conversions of CH₄ and CO₂, selectivities for H₂ and CO, and volume ratio of H₂/CO were 96%, 97%, 98%, 99%, and 0.98, respectively. The average carbon deposition rate over the Ni-Co bimetallic catalyst was only about 0.2 mg·g^-1·h^-1. The characterization results revealed that the sintering speed of the metal greatly decreased with testing time, and the metal particle will not greatly sinter with further testing time. The amount of deposited carbon on the catalyst gradually decreased and growth of filamentous carbon over the surface of the catalyst could be inhibited. Thereby, great catalytic activity and stability could be obtained during the dry reforming of methane reaction.     

负载Ni催化剂上低温甘油蒸汽重整制氢

采用等体积浸渍法制备了Al₂O₃、CeO₂、TiO₂及MgO负载Ni催化剂,考察了它们对甘油蒸汽重整制氢反应的催化性能。采用X射线衍射、N₂吸附、透射电镜及H₂程序升温还原等方法对催化剂进行了表征。结果表明,载体对Ni催化剂的活性有显著影响。在400 ℃下Ni/CeO₂的催化活性明显好于其他催化剂,活性次序为Ni/CeO₂> Ni/Al₂O₃ > Ni/TiO₂ ~ Ni/MgO。Ni/CeO₂也具有好的稳定性,反应20 h未见活性下降,甘油转化率70%,氢气收率69.2%。这与CeO₂的本性及其与活性组分的相互作用有关。Al₂O₃具有较大的比表面积与孔体积,有利于CO吸附及甲烷化反应的进行,使得Ni/Al₂O₃催化剂在较高温度下具有很高的甘油转化率85.7%,但H₂选择性较差。由于MgO载体与活性组分强的相互作用而生成NiMgO₂固溶体,导致Ni/MgO低温活性差。     

CO2预处理操作条件对Ni-Co双金属催化剂性能与结构的影响

与传统H₂预处理方法相比,新型H₂+CO₂预处理方法（HCD）能显著提升Ni-Co双金属催化剂的沼气重整活性及抗积碳性能. 考察了HCD预处理操作条件对催化剂性能与结构的影响. 较好的HCD预处理操作条件是在催化剂经H₂处理之后,再用175-200 mL·min^-1的原料气CH₄/CO₂（比例为0：10）在780-800 ℃下还原0.5-1h. 在优化预处理操作条件下对催化剂进行了511 h的耐久性考察,并运用X射线衍射（XRD）、热重-差示扫描量热（TG-DSC）、透射电子显微镜（TEM）等手段对耐久性测试后的催化剂进行了表征. 在511 h 的稳定性实验内,CH₄、CO₂转化率,H₂、CO选择性及H₂/CO体积比分别高达96%、97%,98%、99%及0.98. 催化剂在测试期间的平均积碳速率仅为0.2 mg·g^-1·h^-1. 在该预处理操作参数下,催化剂拥有最好的综合性能和良好的耐久性.     

Ce改性Co/SEP催化剂对乙醇重整制氢的影响

采用海泡石（SEP）为载体,通过化学沉淀法制备了Co/SEP和Co-Ce/SEP催化剂,对催化剂进行X射线衍射（XRD）、H₂-程序升温还原（H₂-TPR）和透射电镜（TEM）等表征。结果表明,Ce的加入显著改善催化剂的分散度和还原性;两种催化剂应用于乙醇重整制氢实验,考察Ce的加入、反应时间、反应温度和水碳比（S/C比）对制氢的影响。结果表明,在WHSV为20.5h^-1,水碳比（S/C）为3,反应温度600℃时,Co-Ce/SEP乙醇转化率和氢气产率达到最高,分别为85%和65%。同时Ce的添加能使Co-Ce/SEP拥有更优的活性和稳定性。     

蜂窝催化剂上甲醇自热重整制氢的动力学研究

400 ℃～460 ℃,400 h－1～1 600 h－1,O2/CH3OH(mol ratio)=0.10～0.25,H2O/CH3OH (mol ratio) =1.0～1.8下,通过正交实验设计方法,用BSD-2A型内循环无梯度反应器研究了Zn-Cr/CeO2-ZrO2蜂窝催化剂上甲醇自热重整制氢反应的宏观动力学。以甲醇水蒸气重整反应、甲醇分解反应和甲醇完全氧化反应为独立反应进行了研究,得出了幂指数型反应速率表达式,并根据实验结果,利用最小二乘法求解了动力学参数值。F检验表明该动力学模型是高度显著的。该多重反应动力学方程的得出为蜂窝反应器的进一步模拟、优化和设计提供了数据。     

Production of Hydrogen from Bio-oil Using Low-temperature Electrochemical Catalytic Reforming Approach over CoZnAl Catalyst

High-efficient production of hydrogen from bio-oil was performed by electrochemical catalytic reforming method over the CoZnAl catalyst. The influence of current on the hydrogen yield, carbon conversion, and products distribution were investigated. Both the hydrogen yield and carbon conversion were remarkably enhanced by the current through the catalyst, reaching hydrogen yield of 70% and carbon conversion of 85% at a lower reforming temperature of 500 oC. The influence of current on the properties of the CoZnAl catalyst was also characterized by X-ray diffraction, X-ray photoelectron spectroscopy, thermal gravimetric analysis, and Brunauer-Emmett-Teller measurements. The thermal electrons would play an important role in promoting the reforming reactions of the oxygenated-organic compounds in the bio-oil.     

在Ni/HZSM-5催化剂上低温水蒸汽重整生物油制氢

We investigated high catalytic activity of Ni/HZSM-5 catalysts synthesized by the impregna-tion method, which was successfully applied for low-temperature steam reforming of bio-oil. The influences of the catalyst composition, reforming temperature and the molar ratio of steam to carbon fed on the stream reforming process of bio-oil over the Ni/HZSM-5 catalysts were investigated in the reforming reactor. The promoting effects of current passing through the catalyst on the bio-oil reforming were also studied using the electrochemical catalytic re-forming approach. By comparing Ni/HZSM-5 with commonly used Ni/Al₂O₃ catalysts, the Ni₂₀/ZSM catalyst with Ni-loading content of about 20% on the HZSM-5 support showed the highest catalytic activity. Even at 450 oC, the hydrogen yield of about 90% with a near complete conversion of bio-oil was obtained using the Ni₂₀/ZSM catalyst. It was found that the performance of the bio-oil reforming was remarkably enhanced by the HZSM-5 supporter and the current through the catalyst. The features of the Ni/HZSM-5 catalysts were also investigated via X-ray diffraction, inductively coupled plasma and atomic emission spectroscopy, hydrogen temperature-programmed reduction, and Brunauer-Emmett-Teller methods.     

Maximum Hydrogen Production by Autothermal Steam Reforming of Bio-oil With NiCuZnAl Catalyst

Autothermal steam reforming (ATR) of bio-oil, which couples the endothermic steam reform-ing reaction with the exothermic partial oxidation, offers many advantages from a technical and economic point of view. Effective production of hydrogen through ATR of bio-oil was performed at lower temperature with NiCuZnAl catalyst. The highest hydrogen yield from bio-oil reached 64.3% with a nearly complete bio-oil conversion at 600 oC, the ratio of steam to carbon fed (S/C) of 3 and the oxygen to carbon ratio (O/C) of 0.34. The reaction con-ditions in ATR including temperature, O/C, S/C and weight hourly space velocity can be used to control both hydrogen yield and products distribution. The comparison between the ATR and common steam reforming of bio-oil was studied. The mechanism of the ATR of bio-oil was also discussed.     

一种适用于生物油低温制氢的碳纳米纤维促进的镍催化剂

氢气作为一种高热值的清洁能源广泛地应用于工业中. 研究证明: 生物质通过化学过程可以转化为多种气体燃料(氢气), 液体燃料以及高附加值的化学品. 生物质作为一种环境友好型再生洁净能源, 其研究越来越受到关注. 本文旨在探讨利用生物油为原料, 通过水蒸汽重整方法制备富氢合成气的过程. 利用均匀浸渍的方法制备了一种高分散的碳纳米纤维促进的镍(Ni/CNFs)催化剂, 并将普通的Al₂O₃作为载体的Ni/Al₂O₃催化剂和Ni/CNFs作对比. 研究了重整温度以及水蒸汽和碳摩尔比(n_S/n_C)对生物油水蒸汽重整制氢的影响. 结果表明: 碳纳米纤维作为载体用于生物油水蒸汽重整制氢的效果要远优于普通的Al₂O₃载体, 利用22% Ni/CNFs 催化剂时, 在实验温度范围内(350-550℃), 最高生物油转化率和氢气产率分别达到了94.7%和92.1%, 通过研究重整条件以及对催化剂进行表征探讨了生物油在水蒸汽重整过程中催化剂的构效关系.     

Al2O3担载Ni-Cr/MgAl2O4催化剂催化乙醇水蒸气重整制氢研究

利用浸渍法制备了担载于γ-Al2O3上的Ni-Cr/MgAl2O4尖晶石催化剂,考察了催化剂对乙醇水蒸气重整的性能,结合X射线衍射(XRD)的表征结果,研究了催化剂的构效关系.实验结果表明,Ni、Cr担载量为15%和5%的催化剂对乙醇中低温水蒸气重整反应(SRE)表现出较高的催化活性和选择性,400℃时乙醇转化率可达到98.9%,氢气选择性为51.4%;450℃时,转化率可达到100%,氢气选择性为73.8%.     

Highly Active Steam Reforming Catalyst for Hydrogen and Syngas Production

Toyo Engineering Corporation developed a steam reforming catalyst, which is four times as active as conventional catalysts, for hydrogen and syngas production from light natural gas. The catalyst has over three years experience in 1500 t/d class NH₃ plant. Benefits, such as fuel saving, etc., by the developed catalyst are discussed.