SPECTRAL CHARACTERISTICS OF THE EXCITED STATES OF THE PRODUCT OF THE CHEMILUMINESCENCE OF LUMINOL*

Abstract— In dimethylsulfoxide the emission spectrum of luminol chemiluminescence is red-shifted by 300 cm^-1 from the photoexcited fluorescence of the product 3-aminophthalate dianion, while in aqueous solvent the two spectra are identical. The spectral properties of the product dianion have been measured in aqueous solvent and in a number of aprotic solvents, both at room temperature and at 77°K. The ground states and the excited states from which emissions are observed are characterized. Two alternatives are presented to explain the aprotic emission spectra.     

QUANTUM YIELDS OF THE LUMINOL CHEMILUMINESCENCE REACTION IN AQUEOUS AND APROTIC SOLVENTS*

Abstract— Quantum yields for luminol (3-aminophthalic hydrazide) chemiluminescence reactions fall into two classes depending on oxidizing conditions. In aprotic solvents the quantum yield is high and the excitation yield which allows for the fluorescence quantum yield of the product, is 0·09 and is unaffected by changes in solution temperature or polarity, or the presence of quenchers. In aqueous solution under optimum pH conditions (11–13), hydrogen peroxide oxidation results in a high chemiluminescence quantum yield with an excitation yield of 0·04 again unaffected by temperature, viscosity or quenchers. Other oxidizing conditions produce lower quantum yields probably by the introduction of competing chemical pathways. The luminol chemiluminescence light standard has been used to calibrate a spectrofluoro-meter with results in good agreement with the quantum yields of the ferrioxalate actinometer and the fluorescence of quinine sulfate and diphenylanthracene.     

银（III）配合物-鲁米诺流动注射化学发光新体系测定肾上腺素

儿茶酚胺是一类非常重要的神经递质,在人体的心血管系统、神经系统、内分泌腺、肾脏、平滑肌等组织系统的生理活动中起着广泛的调节作用。肾上腺素为儿茶酚胺的一种,建立灵敏、高效的肾上腺素检测技术具有重要的临床意义。本文将银（Ⅲ）配合物与鲁米诺组成新的流动注射化学发光体系,利用碱性介质中肾上腺素对三价银配合物－鲁米诺化学发光体系有明显的增强效应来测定肾上腺素的含量,并据此建立了高效测定肾上腺素的流动注射化学发光新方法。在优化的条件下,该方法测定肾上腺素的线型范围为1.0×10－9～1.0×10－7 mol L-1,检出限为8.0×10－10 mol L-1,对1.5×10－8 mol L-1肾上腺素11次平行测定,其相对标偏差为2.9％。利用建立的分析方法测定了药物肾上腺素,并对三价银－鲁米诺化学发光新体系测定肾上腺素的反应机理进行了讨论。     

Post‐chemiluminescence Method of the Determination of Loperamide Hydrochloride in Human Plasma and Pharmaceutical by Using Dichlorofluorescein as Chemiluminescence Reagent

Abstract

A post‐chemiluminescence (PCL) was observed when loperamide hydrochloride solution was injected into the reaction mixture after the finish of CL reaction of alkaline N‐Chlorosuccinimide (NCS) and dichlorofluorescein. Based on this phenomenon, a simple, sensitive and fast flow injection PCL method was established for the determination of loperamide hydrochloride. The possible mechanism for the PCL reaction was discussed via the investigation of the CL kinetic characteristics, the CL spectra, the fluorescence spectra. The PCL intensity responded linearly to the concentration of loperamide hydrochloride in the range 8.0×10^?10 to 6.0×10^?7 g · ml^?1 with a linear correlation of 0.9995. The detection limit was 4×10^?10 g · ml^?1. The relative standard deviation was 2.4% for 4.0×10^?8 g · ml^?1 loperamide hydrochloride (n=11). This method has been applied to the determination of loperamide hydrochloride in human plasma and pharmaceutical samples with satisfactory results.     

Determination of Gallic Acid by Flow Injection Analysis Based on Luminol‐AgNO3‐Ag NPs Chemiluminescence System

A novel flow injection procedure has been developed for the determination of gallic acid based on the enhancement function for luminol‐AgNO₃‐Ag NPs chemiluminescence (CL) system by gallic acid. The enhancement mechanism was proposed for the reinforcing effect of the gallic acid on the CL system. The UV‐vis absorption spectrum and CL emission spectrum were applied to confirm the mechanism. The method is simple, rapid and sensitive with a detection limit of 5×10^?10 g·mL^?1 and a linear range of 8.0×10^?10–1.0×10^?7 g·mL^?1. The relative standard deviation (RSD) is 1.3% for eleven measurements of 5×10^?8 g·mL^?1 gallic acid. The method has been successfully applied to the determination of gallic acid in Chinese proprietary medicine–Jianmin Yanhou tablets and synthesized samples.     

Raman spectra of chlorophyll forms

The Raman spectra of chlorophyll a (Chl) forms in aqueous poly(vinyl alcohol) (PVA) and in dimethyl sulfoxide (DMSO)—water mixtures were recorded at 457.9 nm excitation and their structures were characterized by comparison with the spectra of the following well-known chlorophyll forms: (1) monomers (Chl)₁ in the polar solvents of group (A), i.e., diethyl ether, tetrahydrofuran, acetone, N,N-dimethylformamide and DMSO, of which the oxygen atom is expected to coordinate to the central magnesium atom; (2) monomers (Chl)₁ in the polar solvents of group (B), i.e., methanol, ethanol, 1-propanol, 2-propanol and 1-butanol, which are supposed to form a hydrogen-bond to the C₉=O group in addition to the coordination-bond to the Mg atom; (3) dehydrated aggregates (Chl)_n in dry non-polar solvents, i.e., carbon tetrachloride, n-hexane and n-octane; and (4) hydrated aggregates (Chl·2H₂O)_n in wet non-polar solvents, i.e., n-hexane and n-octane. The frequency of the C₉ = O stretching Raman line of each of the above chlorophyll forms was: (1) 1702—1680 cm⁻¹; (2) 1673—1668 cm⁻¹; (3) around 1655 cm⁻¹; (4) around 1645 cm⁻¹. The frequency proved to be a marker of intermolecular interaction of the Chl molecules. The spectral patterns in the 1650—700 cm⁻¹ region of (1), (2) and (3) were similar. However, the relative intensities of Raman lines of (4), which was ascribed to a one-dimensional, regular stacking of the Chl macrocycles, were quite different from those of (1)—(3).The chlorophyll form in PVA aqueous solution was identified as (Chl·2H₂O)_n by spectral comparison. The chlorophyll forms present in the DMSO—water mixtures were highly dependent on the DMSO content. It is suggested that (Chl)₁ having hydrogen-bonded H₂O should be present in 10% DMSO solution, and that a new chlorophyll form (Chl·DMSO)_n having (a) a stoichiometric intermolecular interaction with DMSO and (b) a regular stacking of the chlorophyll macrocycles, should be predominant in 50% DMSO aqueous solution.     

Investigating the post-chemiluminescence behavior of phenothiazine medications in the luminol–potassium ferricyanide system: molecular imprinting–post-chemiluminescence method for the determination of chlorpromazine hydrochloride

A new post-chemiluminescence (PCL) phenomenon was observed when phenothiazine medications were injected into the reaction mixture after the chemiluminescence (CL) reaction of luminol and potassium ferricyanide had finished. A possible reaction mechanism was proposed based on studies of the kinetic characteristics of the CL, CL spectra, fluorescence spectra, and on other experiments. The feasibility of determining various phenothiazine medications by utilizing these PCL reactions was examined. A molecular imprinting–post-chemiluminescence (MI-PCL) method was established for the determination of chlorpromazine hydrochloride using a chlorpromazine hydrochloride-imprinted polymer (MIP) as the recognition material. The method displayed high selectivity and high sensitivity. The linear range of the method was 1.0×10⁻⁸∼1.0×10⁻⁶, with a linear correlation coefficient of 0.9985. The detection limit was 3×10⁻⁹ g/ml chlorpromazine hydrochloride, and the relative standard deviation for a 1.0×10⁻⁷ g/ml chlorpromazine hydrochloride solution was 4.0% (n=11). The method has been applied to the determination of chlorpromazine hydrochloride in urine and animal drinking water with satisfactory results.      

H2O2-鲁米诺-荧光素钠-K2CO3高灵敏化学发光法测定二氧化碳

在碱性介质中, CO₃^2－对H₂O₂氧化鲁米诺化学发光反应具有重要作用, 荧光素钠对该反应具有很强的增敏作用. 据此, 建立了化学发光法测定二氧化碳的新方法. 方法的线性范围为1.0×10^－10～5.0×10^－6 mol•L^－1 CO₃^2－, 检出限为 1.2×10^－11 mol•L^－1 CO₃^2－ (相当于5.3×10^－10 g•L^－1 CO₂). 该方法用于室内外空气中二氧化碳含量的测定, 相对标准偏差1.8%～2.1% (n＝11), 加标实验回收率97.6%～101.4%. 论文还探讨了反应的发光机理, 发光反应很可能是由溶液中的CO₃^2－与H₂O₂作用而产生的活性自由基引发, 荧光素钠对发光的增敏作用为化学能量转移过程.     

Silicon-hybrid carbon dots strongly enhance the chemiluminescence of luminol

We report on a 4-min microwave pyrolytic method for the preparation of fluorescent and water-soluble silicon-hybrid carbon dots (C-dots) with high fluorescent quantum yield. The material is prepared by preheating aminopropyltriethoxysilane and ethylene diamine tetraacetic acid for 1 min, then adding a mixture of poly(ethylene glycol) and glycerin to the solution and heating for another 3 min. It is found that the hybrid carbon dots strongly enhance the chemiluminescence (CL) of the luminol/N-bromosuccinimide system. A study on the enhancement mechanism via CL, fluorescence and electron paramagnetic resonance spectroscopy showed that the effect most probably is due to electrostatic interaction between the C-dots and the luminol anion which facilitates electron transfer from luminol anion to the N-bromosuccinimide oxidant. CL intensity is linearly related to the concentration of the C-dots in the range between 1.25 and 20 μg mL^?1. The detection limit is 0.6 μg mL^?1 (at an S/N of 3).

SPECTROSCOPIC STUDIES OF PURINES—I. FACTORS AFFECTING THE FIRST EXCITED LEVELS OF PURINE*

Abstract— Studies of purine absorption and emission in seven solvents differing greatly in dielectric constant and hydrogen bonding potential, reveal a variety of solvent effects. For example, the resolution of structure in the absorption spectrum, the position and/or intensity of the X₂ absorption band, the intensity of fluorescence, the magnitude of the long wave-lenth tail, and the position of the X₁ absorption band are differentially affected—in the order listed—by the solvents tested. Even though it is possible to correlate the extent of decrease in the n-π* tail with increasing solvent dielectric constant, probably alterations in all of these spectroscopic parameters depend most critically upon the ability of the various solvents to form hydrogen bonds with the hydrogen on N9 and/for with the non-bonding electrons on the purine nitrogens: it is tentatively concluded that the probability of hydrogen bonding is directly correlated with the electronegativity of the aza nitrogens (N7 > N3 > N1). In solvents like isopropanol not all of the non-bonding electrons must be solvated maximally in most purine molecules since there is appreciable fluorescence under conditions where a long wavelength tail is readily observed in the absorption spectrum (alternatively some noa-bonding electrons may not te relevant to fluorescence quenching.) Decreases in fluorescence yield are associated with red shifts in the fluorescence maximum, and in the solvents of highest polarity the fluorescence yield is again small indicating that glycerol and water can enhance radiationless tunneling—presumably by altering Franck-Condon configurations and/or improving electronic-vibrational coupling between solute and solvent. The quantum yield is uniform throughout the atsorption band for a given solvent, but studies in aqueous buffers varying from pH 1 to 11 show that the fluorescence yield is greater for charged than for neutral molecules. Further, the fluorescence excitation peak is red shifted in powders. Since phosphorescence is the predominant emission at 777deg;K and increases in fluorescence can be correlated with the presumed solvation of non-bonding electrons, the singlet excited state of lowest energy in ‘unperturbed’ purine must be n-π* in nature. The shape of the phosphorescence band and the decay lifetime of ? 1 sec at 77°K lead to the conclusion that the emitting triplet is a π-π* state. The eight vibrational structures in phosphorescence emission can be readily grouped into two progressions: there is an average separation of about 1300 cm^-1 between peaks within a given progression, and the two sets are mutually displaced by about 500 cm-^l. Individual vibrational peaks are favoured in different solvents and the whole band may be shifted up to 500 cm^-l. Even larger shifts are observed in charged purine molecules and in powders (up to 3000 cm^-l) and the presumed 0–0 band is not observed.     

β—二酮合钴配合物在各种溶剂中与氧反应的热力学性质和动力学

本文研究了二甲亚砜(DMSO),二甲替甲酰胺(DMF)吡啶(py)等溶剂对[Co(acac)_2·2H_2O]载氧和氧化性能的影响.实验证明[Co(acac)_2·2H_2O]与O_2的反应第一步为可逆载氧,而第二步为不可逆载氧.用元素分析和波谱研究了[Co(acac)_2·2H_2O]在溶剂中的存在形态和热力学性质。用配位场理论计算了[Co(acac)_2·2H_2O]在溶剂中的各种配位场参数。动力学的研究表明,[Co(acac)_2·2H_2O]在DMF溶剂中O_2的反应发生一级半过程,一级为[Co(acac)_2·2H_2O]半级为O_2.反应的动力学方程为v=k[Co(acac)_2·2H_2O]·P_(o_2)~(0.41).反应的表观活化能为44.8千焦/摩尔,波谱的分析结果证实,氧化反应的主要产物为[Co(acac)_3]     

Structure and electrospray mass spectrometry studies on dithiacyclooctan-3-ol-containing palladium (II) complex of trans -[Pd(dtco-3-OH)_2](ClO_4)_2·2DMSO

The structure of trans-[Pd(dtco-3-OH)2] (ClO4)2·2DMSO, in which dtco-3-OH is dithiacyclooctan-3-ol and DMSO is dimethyl sulfoxide, was determined by X-ray crystallographic analysis. The crystal data: space group pi, a = 0.7077(2) nm, b = 1.0788(1) nm, c = 1.1111(1) nm, α=67.710(8)°, β = 73. 59(2)°, γ = 85. 39(2)°,R1 = 0 . 0368 and Rw = 0.0998. The palladium (II) is coordinated by four sulfur atoms with a regular square planar configuration. The Pd-S distances are 0.2314(1) and 0.2317(1) nm, respectively. Both dtco-3-OH ligands are in the boat-chair configuration and two hydroxyl groups are on the opposite sites of the PdS4 coordination plane and are towards Pd(II). The Pd-O distance is 0. 285 nm, indicating a weak interaction between them. A typical hydrogen bond between the hydroxyl group of dtco-3-OH ligand and DMSO was observed in the crystal structure. An aqueous solution prepared with the crystals of the complex was used for the investigation of electrospray mass spectrometry ( ESMS ). Besid     

Synthesis and pH-sensitive redox properties of 1,10-phenanthroline-5,6-dione complexes

Synthesis and pH-sensitive electrochemical properties of three complexes, [Cu(PD)₃] · (ClO₄)₂ · 2.25CH₃CN · 6H₂O (1), [Cu(PD)(DMSO)Cl₂] · DMSO · H₂O (2) and [Co(PD)₃] · (ClO₄)₂ · CH₃CN · 2H₂O (3) (PD=1,10-phenanthroline-5,6-dione), are reported. Single-crystal X-ray diffraction of the complexes suggest that the structure of 1 is orthorhombic, 2 triclinic and 3 orthorhombic. The electrochemical properties of free PD and the three complexes in phosphate buffer solutions in a pH range between 2 and 9 have been investigated using cyclic voltammetry. The redox potentials of these compounds are strongly dependent on the proton concentration in the range ?0.3 V ～ 0.4 V versus SCE (saturated calomel reference electrode). The reduction behavior of PD can be described from quinone species to semiquinone anion then to the fully reduced dianion. At pH < 4, the reduction of PD proceeds via 2e^?/3H⁺ processes, while at pH > 4, the reduction of PD proceeds via 2e^?/2H⁺. For all complexes, the N–N chelate PD ligand is electrochemically active and underwent step reduction via 2e^?/2H⁺.     

Dediazoniation of arenediazonium ions in homogeneous solution. Part VIII. Reaction kinetics and products in dimethyl sulfoxide

p-Nitrobenzenediazonium tetrafluoroborate dissolved in dimethylsulfoxide (DMSO) at 50° forms p-nitrophenol in 88–90% yield. The phenolic oxygen atom originates exclusively from the oxygen atom of DMSO as demonstrated by the use of ¹⁸O-labelled DMSO. The first-order rate of dediazoniation is the same under N₂ as it is in the presence of air. The rate is little influenced by the addition of benzene or iodobenzene. However, the products formed in the presence of these additives are significantly different. UV. spectra and the reactivity of diazonium salt solutions in DMSO when mixed with reagents in aqueous solution demonstrate that a relatively stable charge-transfer complex is formed between the diazonium ion and DMSO. The product analyses and the kinetic and spectral results of dediazoniation in DMSO with and without additives are consistent with a mechanism in which the rate-limiting step is the formation of a p-nitrophenyl radical from the charge-transfer complex. p-Nitrophenol and the products with benzene and iodobenzene are formed in subsequent fast competition steps. In the presence of small amounts of pyridine the dediazoniation is much faster and follows a different kinetic law. Pyridine effectively competes with DMSO in the reaction with diazonium ions.     

'Uphill' energy transfer in a photosynthetic bacterium

Abstract— Detectable energy flow in the ‘uphill’ direction was demonstrated by exciting the fluorescence of a shorter wavelength band of Rhodopseudomonas spheroides with light absorbed by a longer wavelength band. A variation in the fluorescence spectrum which depends on the state of the traps was also demonstrated. This information, coupled with fluorescence data obtained with monochromatic light, leads to the conclusion that for the longest wavelength bands the ‘uphill’ transfer is about as fast as transfer to the traps; i.e. the ‘average’ rate constant is on the order of 10⁹ sec. The ratio of the uphill to downhill rate agrees with a theoretical estimate of about 0·5. Some possible ramifications of such uphill flow are discussed.     

Synthesis,spectral, thermal,solid-state DC electrical conductivity and biological studies of Co(II) complexes with Schiff bases derived from 3-substituted-4-amino-5-hydrazino-1,2,4-triazole and substituted salicylaldehydes

A series of Co(II) complexes have been synthesized with Schiff bases derived from 3-substituted-4-amino-5-hydrazino-1,2,4-triazole and substituted salicylaldehydes. These complexes are insoluble in water but more soluble in DMF and DMSO. The complexes have been characterized by elemental analyses, spectral (IR, UV–Vis, ¹H-NMR, FAB-mass, fluorescence), magnetic, thermal, solid-state DC electrical conductivity and molar conductance data. The molar conductivity values indicate that they are non-electrolytes. The elemental analyses of the complexes suggest a stoichiometry of the type Co · L1–L16 · 2H₂O. The complexes have been considered as semiconductors on the basis of the solid-state DC electrical conductivity data. Fluorescence spectra of one Schiff base and its complex were investigated in various solvents and some of the Schiff bases and their complexes were evaluated for their antimicrobial activities.     

Quantitative Monitoring of Rutin in Human Urine by Flow Injection‐Chemiluminescence Analysis

In this paper, a rapid and sensitive flow injection‐chemiluminescence (FI‐CL ) method is proposed for the quantitative determination of rutin based on the inhibitory effect of rutin on the chemiluminescence intensity from the luminol–chymotrypsin (CT ) system. The decrease of CL intensity was found to be proportional to the logarithm of rutin concentration in the range 0.1–30.0 ng/mL . A method for the quantification of rutin is proposed, with the limit of detection (LOD ) of 0.03 ng/mL (3σ). A complete analytical process including sampling and washing for rutin determination, which was conducted at a flow rate of 2.0 mL /min, could be performed completely within 30 s, yielding a sample efficiency of 120 h⁻¹. The proposed procedure was successfully applied for the determination of rutin in human urine after oral intake, with recoveries varying from 93.9 to 108.1% and relative standard derivation <4.0% (n = 5). Results showed that urine reached the maximum concentration at ~2.5 h, and the total excretion ratios were (83.5 ± 0.6) and (86.8 ± 0.7)%, respectively, for two volunteers in 8 h. The pharmacokinetic parameters, including the half‐life (1.05 ± 0.02 h), absorption rate constant (1.18 ± 0.01 h⁻¹), and elimination rate constant (0.70 ± 0.01 h⁻¹), were obtained. The possible CL mechanism of the luminol–CT –rutin reaction is discussed by FI‐CL , fluorescence, and molecular docking methods.     

Picomole‐level Formaldehyde Determination in Gaseous and Beer Samples Using Flow Injection Chemiluminescence Analysis

Based on the linear enhancement of formaldehyde (FA) within 7.0 ～ 1000 pmol l^?1 on luminol—bovine serum albumin (BSA) chemiluminescence (CL) system, FA determination in air and beer samples using CL with flow injection (FI) was proposed. The detection limit was 2.5 pmol l^?1 (3σ) and the relative standard deviations were less than 4.5% (n = 7). At a flow rate of 2.0 mL min^?1, a whole analysis from sampling to washing only needed 32 s, offering a sample throughput of 112 h^?1. This proposed method was successfully utilized to determine FA vapor pressure in liquid (121.8 ± 3.8 Pa), FA content in real air sample (8.93 ± 0.03 mg m^?3), and FA levels in beer (199.5 ± 5.6 ～ 225.2 ± 3.5 mg l^?1), giving determination recoveries from 90.7% to 109.3%. The mechanism of BSA—FA interaction was also investigated, showing FA binding to BSA was a spontaneous process mainly through hydrogen bonding and van der Waals force by FI‐CL, with binding constant K of 1.89 × 10⁶ l mol^?1 and the number of binding sites n of 0.86. Molecular docking analysis further revealed FA could enter into the pocket at subdomain IIA of BSA, with K of 1.71 × 10⁵ l mol^?1 and ΔG of ‐29.68 kJ mol^?1.     

Some donor-acceptor complexes of silicon phthalocyanine dianions

Studying the reaction of PcSiX₂ (X = Cl, OH) with KOH in DMSO we first discovered red D-A complexes [(Pc²⁻)·PcSiX²] and [(Pc²⁻)·O²] in which silicon phthalocyanine dianion Pc²⁻ is a donor, and the parent phthalocyanine silicon or oxygen are acceptors of electron density. The complexes were characterized by electron absorption, NMR, and ESR spectra. In the reactions with Me₃SiCl, H₂O, or CH₃COOH the complexes regenerate phthalocyanine and O₂. In O₂ atmosphere the [(Pc²⁻)·O₂] complex gradually degrades affording a product of unknown nature.     

Effect of fsDNA on chemiluminescence characteristics of luminol–H2O2 system catalyzed by Mn(III)–Tetrakis (4-sulfonatophenyl)-porphyrin

In the present work, the effect of fsDNA (fish sperm DNA) on kinetic parameters of chemiluminescence (CL) of the luminol–hydrogen peroxide system catalyzed by Mn(III)–Tetrakis (4-sulfonatophenyl)-porphyrin was investigated. These parameters including pseudo first-order rise and fall rate constant for the chemiluminescence burst, maximum level intensity, time to reach maximum intensity, total light yield, and values of the intensity at maximum CL were evaluated by computer fitting of the resulted intensity–time plots. Results reveal that CL parameters are dramatically affected due to interaction of metalloporphyrin with DNA. In order to observe quenching effect of DNA on CL intensity, Stern–Volmer plot with k _Q value of 1.18 × 10⁵ M^?1 was calculated in the quencher concentration range of 4 × 10^?6–8.5 × 10^?5 M.