Initiation and termination mechanism in the cooligomerization of the styrene–methyl methacrylate–carbon tetrachloride system

The analysis of the endgroups of the oligomers produced in the styrene (A)–CCl₄(S) system (system I), the methyl methacrylate(B)–CCl₄ system (system II), and the styrene–methyl methacrylate–CCl₄ system (system III) was carried out in order to clarify the mechanism of the initiation, transfer, and termination. In system I, the number of Cl atoms per oligomer molecule N_Cl increases with the molar ratio of [S]/[A] when the molar ratio of [S]/[A] is below unity and is about four when the molar ratio of [S]/[A] is above unity, and the number of initiator fragments per oligomer molecule N_I decreases with the increase in the molar ratio of [S]/[A]. In system II, N_Cl is about 0.45 over a considerably wide range of the molar ratio of [S]/[B]. In system III, N_Cl increases and N_I decreases with the increase in the molar ratios of [S]/([A] + [B]) and [A]/[B]. From the data of N_Cl and N_I, the fraction I_CC14 of the initiation by the tri-chloromethyl radical in the overall initiation reactions and the fraction T_CC14 of the chain transfer reaction of the growing radical of styrene in all the reactions which produce the cooligomer in the system III were calculated. I_CCl3 and T_CC14 both increase with the molar ratios [S]/([A] + [B]) and [A]/[B].     

Computer simulation for the cooligomerization system

In order to clarify the kinetic features of the styrene (A)–methyl methacrylate (B)–CCl₄(S) cooligomerization system, a computer simulation was carried out. The experimental data on the degree of polymerization and the deviation of the cooligomer composition from the statistical steady-state composition were comparatively well explained by calculations based on the kinetic equations derived from the assumed reaction scheme and the values of the velocity coefficients, although the values of the four velocity coefficients in the initiation step and the velocity coefficient of the termination by the coupling of two solvent radicals were estimated. The results of the calculation of the rate of each component reaction show that the following two reactions are the most important in the initiation and in the transfer and termination steps when the [S]/([A] + [B]) ratio is large: where, A, A*, and P are styrene, polystyryl radical, and the cooligomer, respectively. Moreover, it was concluded that the deviation of the cooligomer composition from the statistical steady-state composition was caused by these two reactions.     

Simplified treatment of cooligomerization kinetics

Equations for the degree of polymerization and the cooligomer composition in the styrene (A)–methyl methacrylate (B)–CCl₄(S) system were derived from the assumed reaction scheme by the use of some assumptions for simplification, and their appropriateness was examined. The chain transfer constants of the growing radicals of styrene (C_SA) and methyl methacrylate (C_SB) to CCl₄, which were estimated from the apparent chain transfer constants C_SAB in the cooligomerization system, agreed with the homooligomerization values. This means that the degree of the polymerization of the cooligomer can be expressed by the equation: where P_n is the degree of polymerization of the cooligomer and P_nO is that when no chain transfer agent (CCl₄) is added; r_A and r_B are the monomer reactivity ratios of monomers A and B in this system. The cooligomer composition deviated from the statistical steady-state composition on the low molecular weight side, and this deviation was explained by the equation:      

Polymerization of coordinated monomers. XIV. Systematic deviations from alternating regulation in copolymerization of methyl methacrylate with styrene in the presence of metal halides

Methyl methacrylate (MMA) and styrene (St) copolymerize in the presence of zinc chloride at 3°C under photoirradiation. The contents of methyl methacrylate in the copolymers obtained at a [ZnCl₂]/[MMA] molar ratio of 0.4 are systematically larger than 53 mole %, which is the limiting value at a small feed ratio of methyl methacrylate. The resulting copolymers are confirmed as the sole products and not the mixtures by thin layer chromatography. The effect of dilution of the monomer feed mixture with toluene on copolymer composition suggests that it depends chiefly on the feed concentration of styrene and hardly at all on monomer feed ratios. Copolymerizations are also conducted in the presence of stannic chloride at ?17°C under photoirradiation and in the presence of ethylaluminium sesquichloride at 0°C with spontaneous initiation. The contents of methyl methacrylate in both copolymers obtained at feed ratios lower than 60 mole % almost correspond to the 1:1 alternating copolymer and increase systematically with higher feed ratios. The systematic deviations of copolymer composition obtained in the presence of metal halides are reasonably interpreted by the participation of the binary molecular complex composed of metal halide and methyl methacrylate in the polymerization of the ternary molecular complex composed of metal halide, methyl methacrylate, and styrene.     

Polymerization of methyl methacrylate by the binary system of the copper–amine complex type resin and carbon tetrachloride

The polymerization of vinyl monomers initiated by binary initiator systems composed of a copper–amine complex type resin and organic halides has been studied. These binary systems initiated the polymerization of various vinyl monomers. A kinetic study of the polymerization of methyl methacrylate initiated by the copper–amine complex resin–CCl₄ system was carried out, and it was found that the polymerization proceeds by way of a radical mechanism. This fact was also supported by the copolymerization of methyl methacrylate with styrene. The overall activation energy of the polymerization of methyl methacrylate was estimated as 8.4 kcal/mole. The activity of the initiator systems was greatly dependent upon the dissociation energy of carbon–halogen bonds in the organic halides. A possible initiation mechanism with the binary systems is proposed and discussed.     

A sterically hindered cobalt o-iminobenzosemiquinone complex in the polymerization of vinyl monomers

The influence of bis[4,6-di-tert-butyl-N-(2,6-dimethylphenyl)-o-iminobenzosemiquinonato]cobalt (II) on the radical polymerization of methyl methacrylate and styrene under the conditions of radical initiation by azo-bis-isobutyric acid dinitrile in the temperature range 70–90°C has been studied. The use of the cobalt complex containing redox-oxidized ligands leads to the suppression of autoacceleration of the polymerization of methyl methacrylate and to a linear increase in the molecular masses of the polymers with conversion. In the case of styrene polymerization, the control over the kinetics of the process and molecular weight characteristics of the polymers synthesized in the presence of the cobalt iminobenzosemiquinone complex is less pronounced.     

Atom transfer radical polymerization of styrene and methyl methacrylate catalyzed by FeCl2/iminodiacetic acid

The atom transfer radical polymerization of styrene and methyl methacrylate with FeCl₂/iminodiacetic acid as the catalyst system in bulk was successfully implemented at 70 and 110 °C, respectively. The polymerization was controlled: the molecular weight of the resultant polymer was close to the calculated value, and the molecular weight distribution was relatively narrow (weight‐average molecular weight/number‐average molecular weight ∼ 1.5). Block copolymers of polystyrene‐b‐poly(methyl methacrylate) and poly(methyl methacrylate)‐b‐poly(methyl acrylate) were successfully synthesized, confirming the living nature of the polymerization. A small amount of water added to the reaction system increased the reaction rate and did not affect the living nature of the polymerization system. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 4308–4314, 2000     

Kinetics of PdII‐catalyzed polymerization of methyl methacrylate by triethanolamine in the presence of CCl4

Polymerization of methyl methacrylate (MMA) with triethanolamine (TEA) and carbon tetrachloride has been investigated in the presence of PdCl₂ and in a dimethylsulfoxide (DMSO) medium by employing a dilatometric technique at 60°C. The rate of polymerization has been obtained under the conditions [CCl₄]/[TEA] ≤ 1. The kinetic date indicate the possible participation of the charge‐transfer complex formed between the {amine–Pd^II} complex and CCl₄ in the polymerization of MMA. In the absence of either CCl₄ or amine, no polymerization of MMA was observed under the present experimental conditions. The rate of polymerization was inhibited by hydroquinone, suggesting a free‐radical initiation. © 2000 John Wiley & Sons, Inc. Int J Chem Kinet 32: 171–177, 2000     

Luminescent polymeric ruthenium complexes with polystyrene‐b‐poly(methyl methacrylate) macroligands: The sequential activation of initiator sites for blocks generated by parallel polymerization mechanisms

The synthesis of polystyrene‐b‐poly(methyl methacrylate) diblock copolymers with a luminescent ruthenium(II) tris(bipyridine) [Ru(bpy)₃] complex at the block junction is described. The macroligand precursor, polystyrene bipyridine‐poly(methyl methacrylate) [bpy(PS–H)(PMMA)], was synthesized via the atom transfer radical polymerization of styrene and methyl methacrylate from two independent, sequentially activated initiating sites. Both polymerization steps resulted in the growth of blocks with sizes consistent with monomer loading and narrow molecular weight distributions (i.e., polydispersity index < 1.3). Subsequent reactions with ruthenium(II) bis(bipyridine) dichloride [Ru(bpy)₂Cl₂] in the presence of Ag⁺ generated the ruthenium tris(bipyridine)‐centered diblock, which is of interest for the imaging of block copolymer microstructures and for incorporation into new photonic materials. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 4250–4255, 2002     

Immobilized copper catalyst for atom transfer radical addition and polymerization

A novel multidentate amine grafted on silica gel and magnetic microsphere was prepared. Its chemical structure was confirmed by C¹³ NMR, XPS and FTIR, and the nitrogen content was determined by elemental analysis. It was also used as a ligand for CuCl and successfully catalyzed the atom transfer radical addition of both carbon tetrachloride (CCl₄) to methyl methacrylate and methyl trichloroacetate to styrene, repeatedly. The conversion and purity of the product were determined through gas chromatography and ¹H NMR, respectively. The immobilized copper catalyst complex was also used in atom transfer radical polymerization of styrene initiated by 1,1,1,3‐tetrachloro‐3‐phenylpropane and methyl methacrylate initiated by methyl 2‐methyl‐2,4,4,4‐tetrachlorobutyrate, respectively. Although the polymerization took place successfully, it did not proceed in a controlled fashion. Copyright © 2010 John Wiley & Sons, Ltd.     

Reverse atom transfer radical solution polymerization of methyl methacrylate under pulsed microwave irradiation

The reverse atom transfer radical polymerization (RATRP) of methyl methacrylate (MMA) was successfully carried out under pulsed microwave irradiation (PMI) at 69 °C with N,N‐dimethylformamide as a solvent and with azobisisobutyronitrile (AIBN)/CuBr₂/tetramethylethylenediamine as an initiation system. PMI resulted in a significant increase in the polymerization rate of RATRP. A 10.5% conversion for a polymer with a number‐average molecular weight of 34,500 and a polydispersity index of 1.23 was obtained under PMI with a mean power of 4.5 W in only 52 min, but 103 min was needed under a conventional heating process (CH) to reach a 8.3% conversion under identical conditions. At different [MMA]₀/[AIBN]₀ molar ratios, the apparent rate constant of polymerization under PMI was 1.5–2.3 times larger than that under CH. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 3823–3834, 2002     

Reverse atom transfer radical polymerization of vinyl monomers with Fe[SC(S)NEt2]3 alone as the catalyst

The living radical polymerization of methyl methacrylate and styrene was successfully carried out with diethyl 2,3‐dicyano‐2,3‐diphenylsuccinate (DCDPS)/ferric tri(diethyldithiocarbamate) as a novel reverse atom transfer radical polymerization initiation system in which DCDPS was a hexa‐substituted ethane‐type thermal iniferter, DC was a diethyldithiocarbamate group, and no additional ligands such as nitrogen‐ or phosphine‐based compounds were required. The bulk polymerization of methyl methacrylate was carried out at 95 °C, and that of styrene was carried out at 120 °C. Poly(methyl methacrylate) and polystyrene (PSt) with high molecular weights and quite narrow molecular weight distributions (as low as 1.09 for PSt) were obtained. ¹H NMR spectroscopy revealed the presence of an α‐(carbethoxycyanophenyl)methyl group from the initiator and an ω‐DC group from the catalyst in the obtained polymers. Various chain‐extension reactions under UV light or thermal treatments were successfully conducted to prove the presence and efficient reinitiating of the ω‐DC group. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 3464–3473, 2001     

The effect of mixed solvents pyridine–carbon tetrachloride on the radical polymerization of methyl methacrylate

A study was made of the methyl methacrylate (MMA) solution polymerization in CCl₄-pyridine mixtures as well as in net components at 30, 50, and 70°C. The results obtained show that there are no significant deviations from additivity in the overall chain transfer constants that fit the straight line between the values of Cs for CCl₄ and pyridine. It can be concluded that the EDA interaction between CCl₄ and pyridine does not change the sensitivity of each component for chain transfer from propagation PMMA free radical. The pyridine in the system increases the rate of MMA polymerization as a result of the higher rate of initiation.     

Determination of chain transfer constant to dodecanethiol in styrene/methyl methacrylate and butyl acrylate/methyl methacrylate copolymerization and effect of chain length on composition and stereochemical configuration of copolymers

Free radical copolymerization of styrene/methyl methacrylate (S/MMA) and butyl acrylate/methyl methacrylate (BA/MMA) in the presence of n-dodecanthiol (DDT) has been studied at 60°C in a 3 mol/L benzene solution using 2,2′-azobis(isobutyronitrile) (AIBN) as initiator. Overall chain transfer constant to DDT has been determined for both copolymerization systems, as a function of monomer feed composition using complete molecular weight distribution and the Mayo method. Overall transfer coefficients have values which are dependent on both monomer feed composition and individual comonomer transfer values. Composition, sequence distribution, and stereoregularity of copolymers obtained are, in our experimental conditions, independent of copolymer molecular weight. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 2913–2925, 1998     

Facile synthesis of AB2‐type miktoarm star polymers through the combination of atom transfer radical polymerization and ring‐opening polymerization

A novel miktofunctional initiator ( 1 ), 2‐hydroxyethyl 3‐[(2‐bromopropanoyl)oxy]‐2‐{[(2‐bromopropanoyl)oxy]methyl}‐2‐methyl‐propanoate, possessing one initiating site for ring‐opening polymerization (ROP) and two initiating sites for atom transfer radical polymerization (ATRP), was synthesized in a three‐step reaction sequence. This initiator was first used in the ROP of ?‐caprolactone, and this led to a corresponding polymer with secondary bromide end groups. The obtained poly(?‐caprolactone) (PCL) was then used as a macroinitiator for the ATRP of tert‐butyl acrylate or methyl methacrylate, and this resulted in AB₂‐type PCL–[poly(tert‐butyl acrylate)]₂ or PCL–[poly(methyl methacrylate)]₂ miktoarm star polymers with controlled molecular weights and low polydispersities (weight‐average molecular weight/number‐average molecular weight < 1.23) via the ROP–ATRP sequence. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2313–2320, 2004     

以双硫酯为链转移剂的活性自由基聚合

合成并研究了两种双硫酯链转移剂的纯化方法 ,进行了多种单体以双硫酯为链转移剂的活性自由基聚合及嵌段共聚 .发现以PhC(S)SC(CH3) 2 Ph为链转移剂的效果比PhC(S)SCH(CH3)Ph好 ,聚合产物的多分散性系数较小 .引发剂与链转移剂的摩尔数比为 1∶3 5～ 1∶4 2时 ,得到多分散性系数小 ,实测分子量与理论分子量相近的聚合产物 .聚合物的分子量随时间和转化率的增加而增加 ,加入第二单体形成嵌段共聚物 ,具有活性聚合特征 .聚甲基丙烯酸酯大分子引发剂引发丙烯酸酯单体聚合时 ,聚合速度最快 .     

Modeling of unseeded emulsion copolymerization of styrene and methyl methacrylate

A mathematical model for the unseeded emulsion copolymerization of styrene and methyl methacrylate has been developed. This model, which includes a new rate coefficient for radical desorption, was used to analyze the effect of the styrene/methyl methacrylate molar ratio in the initial charge on the number of particles, overall conversion and copolymer composition. It was found that the number of particles increased with the methyl methacrylate content and that a drift of the copolymer composition resulted during the polymerization of styrene/methyl methacrylate molar ratios other than 50/50. Good agreement between experimental results and model predictions was achieved.     

Atom transfer radical copolymerization of acrylonitrile and ethyl methacrylate at ambient temperature

Copolymerization of acrylonitrile (AN) and ethyl methacrylate (EMA) using copper‐based atom transfer radical polymerization (ATRP) at ambient temperature (30 °C) using various initiators has been investigated with the aim of achieving control over molecular weight distribution. The effect of variation of concentration of the initiator, ligand, catalyst, and temperature on the molecular weight distribution and kinetics were investigated. No polymerization at ambient temperature was observed with N,N,N′,N′,N″‐pentamethyldiethylenetriamine (PMDETA) ligand. The rate of polymerization exhibited 0.86 order dependence with respect to 2‐bromopropionitrile (BPN) initiator. The first‐order kinetics was observed using BPN as initiator, while curvature in first‐order kinetic plot was obtained for ethyl 2‐bromoisobutyrate (EBiB) and methyl 2‐bromopropionate (MBP), indicating that termination was taking place. Successful polymerization was also achieved with catalyst concentrations of 25 and 10% relative to initiator without loss of control over polymerization. The optimum [bpy]₀/[CuBr]₀ molar ratio for the copolymerization of AN and EMA through ATRP was found to be 3/1. For three different in‐feed ratios, the variation of copolymer composition (F_AN) with conversion indicated toward the synthesis of copolymers having slight changes in composition with conversion. The high chain‐end functionality of the synthesized AN‐EMA copolymers was verified by further chain extension with methyl acrylate and styrene. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1975–1984, 2006     

Polymerization of methyl methacrylate by charge-transfer mechanism with aliphatic primary amines and carbon tetrachloride

Polymerization of methyl methacrylate (MMA) with aliphatic primary amines and carbon tetrachloride has been investigated in th dimethylsulfoxide medium by employing a dilatometric technique at 60°C. The rate of polymerization (R_p) has been evaluated under the conditions, [CCl₄]/[amine] < 1 and > 1. The kinetic data indicate possible participation of the charge transfer complexes formed between the amine + CCl₄ and the amine + MMA in the polymerization of MMA. In the absence of CCl₄ or amine, no polymerization of MMA was observed under the present experimental conditions. The polymerization of MMA was inhibited by hydroquinone, indicating a free radical initiation. The energy of activation varied from 32 to 58 kJ mol^?1.     

Polymerization of coordinated monomers. III. Copolymerization of acrylonitrile–zinc chloride,methacrylonitrile–zinc chloride or methyl methacrylate–zinc chloride complex with styrene

The 1:1 or 2:1 complex of acrylonitrile, methacrylonitrile, or methyl methacrylate with ZnCl₂ was copolymerized with styrene at the temperature of 0–30°C without any initiator. The structure of the copolymer from methyl methacrylate complex and styrene was examined by NMR spectroscopy. The complexes of acrylonitrile or methacrylonitrile with ZnCl₂ gave a copolymer containing about 50 mole-% styrene units. The complexes of methyl methacrylate yielded an alternating copolymer when the feed molar ratio of methyl methacrylate to styrene was small, but with increasing feed molar ratio the resulting copolymer consisted of about 2 moles of methyl methacrylate per mole of styrene. The formation of a charge-transfer complex of styrene with a monomer coordinated to zinc atom was inferred from the ultraviolet spectra. The regulation of the copolymerization was considered to be effected by the charge-transfer complex. The copolymer resulting from the 2:1 methyl methacrylate–zinc chloride complex had no specific tacticity, whereas the copolymer from the 1:1 complex was richer in coisotacticity than in cosyndiotacticity. The change of the composition of the copolymer and its specific tacticity in the polymerization of the methyl methacrylate complex is related to the structure of the complex.