Influence of laser irradiation on the optical and structural properties of poly(ethylene terephthalate) fibres

Laser irradiation has been previously investigated for achieving uniform heating of polyethylene terephthalate (PET) fibres in the hot-drawing stage of the production process, so as to obtain better fibre mechanical properties. The optical properties and dye uptake of PET fibres also depend on the polymer chain orientation and crystallinity within the fibre structure. This paper reports an investigation of a concept whereby laser irradiation and interferometry could be used to modify and trace a small change in the optical properties of a PET monofilament fibre, but the corresponding change in the dye uptake would not be detected visually. A copper vapour laser (550-580 nm wavelengths) was used to expose consecutive 4 mm lengths along a running length of monofilament to 39.8 W cm⁻², at a pulse rate of 9.89 kHz in order to modify, in a controlled way, the polymer crystallinity and orientation. A 3D finite element simulation, based on uncoupled heat-transfer analysis, indicated that rapid heating and cooling could be obtained with the laser to give the small changes required. Irradiated and untreated samples were analysed by interferometry and a 0.16% change was detected in the birefringence profiles, corresponding to a small reduction in the degree of orientation and crystallinity of the irradiated samples. Density measurements and wide-angle X-ray scattering (WAXS) analysis confirmed the change in crystallinity. Tests conducted for dye adsorption and tensile strength showed a small increase in the former and only a very small decrease in the latter. It was concluded that these changes in property provide the opportunity for a laser-irradiated PET monofilament fibre to be used as a subtle tracer element in brand labels for textile garments as an anti-counterfeit measure.     

Influence of annealing temperature on structural,electrical and optical properties of WSi2

WSi₂ polycrystalline films of different thicknesses were prepared by low pressure chemical vapor deposition on silicon wafers, and their crystallization properties were studied as a function of the annealing temperature. Structural measurements were performed by X-ray diffraction, detailing for the first time the phase transition from the amorphous to the hexagonal structure at an annealing temperature 380° C and from hexagonal to tetragonal above 700° C. The electrical sheet resistance showed the same transition temperatures.Optical characterization was performed by spectroscopic ellipsometry, and the real and imaginary part of the complex refractive index were obtained as a function of the annealing temperature in the 0.25–0.9 m wavelength range. A broad optical band was found for samples annealed up to 700° C, while for higher annealing temperatures a transparency region for wavelengths greater than 0.5 m and some significant structures appear. A corresponding behavior was observed in the infrared reflectance spectra. Furthermore, it was shown that the determination of the thickness of SiO₂ grown on WSi₂ requires a multilayer model, taking into account the transparency of tetragonal WSi₂.     

衬底温度对HfO_2薄膜结构和光学性能的影响

采用直流磁控反应溅射法,分别在室温,200,300,400和500℃下制备了HfO2薄膜。利用X射线衍射(XRD)、椭圆偏振光谱(SE)和紫外可见光谱(UVvis)研究了衬底温度对HfO2薄膜的晶体结构和光学性能的影响。XRD研究结果显示:不同衬底温度下制备的HfO2薄膜均为单斜多晶结构;随衬底温度的升高,(-111)面择优生长更加明显,薄膜中晶粒尺寸增大。SE和UVvis研究结果表明:随衬底温度升高,薄膜折射率增加,光学带隙变小;制备的HfO2薄膜在250～850nm范围内有良好的透过性能,透过率在80%以上。     

Influence of curvature on the transmission properties of plastic optical fibres

The effect of fibre bending on the passage of a laser beam through a cladded plastic optical fibre has been investigated. Results indicate that the additional loss is determined by the bending radius, the locus of a bend, and the aperture angle of the applied launching system.     

Influence of annealing temperature on the structural, optical and mechanical properties of ALD-derived ZnO thin films

ZnO thin films grown on Si(1 1 1) substrates by using atomic layer deposition (ALD) were annealed at the temperatures ranging from 300 to 500 °C. The X-ray diffraction (XRD) results show that the annealed ZnO thin films are highly (0 0 2)-oriented, indicating a well ordered microstructure. The film surface examined by the atomic force microscopy (AFM), however, indicated that the roughness increases with increasing annealing temperature. The photoluminescence (PL) spectrum showed that the intensity of UV emission was strongest for films annealed at 500 °C. The mechanical properties of the resultant ZnO thin films investigated by nanoindentation reveal that the hardness decreases from 9.2 GPa to 7.2 GPa for films annealed at 300 °C and 500 °C, respectively. On the other hand, the Young's modulus for the former is 168.6 GPa as compared to a value of 139.5 GPa for the latter. Moreover, the relationship between the hardness and film grain size appear to follow closely with the Hall-Petch equation.     

醋酸锌热解温度对ZnO纳米棒的结构及光学性质的影响

采用水热法在普通载玻片上热解醋酸锌生成的ZnO种子层上制备ZnO纳米棒, 采用 X射线衍射仪、扫描电镜、分光光度计等测试手段详细研究了醋酸锌热解温度对 ZnO纳米棒的结构和光学性质的影响. 结果表明: 纳米棒的结晶质量、端面尺寸、宏观应力和透射率与醋酸锌热解温度有密切关系. 随着热解温度的增加, ZnO纳米棒具有的c轴择优取向性先增强后减弱, 拉应力先减小后增大, 可见光区的平均透射率先增大后减小. 热解温度为350 ℃时, ZnO纳米棒c轴择优取向性最强, 拉应力最小, 平均透射率最大. 端面尺寸诱导的表面散射 是影响ZnO纳米棒可见光区平均透射率的主要机制. 关键词： 醋酸锌 水热法 ZnO纳米棒     

The effect of mechanical drawing on optical and structural properties of nylon 6 fibres

The Pluta polarizing double-refracting interference microscope was attached to a mechanical drawing device to study the effect of cold drawing on the optical and structural properties of nylon 6 fibres. The microscope was used in its two positions for determining the refractive indices and birefringence of fibres. Different applied stresses and strain rates were obtained using the mechanical-drawing device. The effect of the applied stresses on the optical and physical parameters was investigated. The resulting optical parameters were utilized to investigate the polarizability per unit volume, the optical orientation factor, the orientation angle and the average work per chain. The refractive index and birefringence profiles were measured. Relationships between the average work per chain and optical parameters at different strains rates were determined. An empirical formula was deduced for these fibres. Micro-interferograms are given for illustration.     

衬底温度对HfO2薄膜结构和光学性能的影响

采用直流磁控反应溅射法,分别在室温,200,300,400和500 ℃下制备了HfO2薄膜。利用X射线衍射（XRD）、椭圆偏振光谱（SE）和紫外可见光谱（UV-vis）研究了衬底温度对HfO2薄膜的晶体结构和光学性能的影响。XRD研究结果显示：不同衬底温度下制备的HfO2薄膜均为单斜多晶结构;随衬底温度的升高,（-111）面择优生长更加明显,薄膜中晶粒尺寸增大。SE和UV-vis研究结果表明：随衬底温度升高,薄膜折射率增加,光学带隙变小;制备的HfO2薄膜在250～850 nm范围内有良好的透过性能,透过率在80%以上。     

Propagation of partial coherence along optical fibres

The degree of coherence of the field along an optical fibre excited by a spatially coherent source is discussed. The degree of coherence undergoes a transitions as the source becomes less coherent; initially it is determined by the source coherence properties but for highly incoherent source it is controlled by fibre acceptance parameters.     

Influence of Si doping on the structural and optical properties of InGaN epilayers

Influences of the Si doping on the structural and optical properties of the InGaN epilayers are investigated in detail by means of high-resolution X-ray diffraction （HRXRD）, photolumimescence （PL）, scanning electron microscope （SEM）, and atomic force microscopy （AFM）. It is found that the Si doping may improve the surface morphology and crystal quality of the InGaN film and meanwhile it can also enhance the emission efficiency by increasing the electron concentration in the InGaN and suppressing tile formation of V-defects, which act as nonradiative recombination centers in the InGaN, and it is proposed that the former plays a more important role in enhancing the emission efficiency in the InGaN.     

Influence of Tb incorporation on the structural and the optical properties of ZnO nanoparticles

Structural and optical properties of the Tb doped ZnO nanoparticles are systematically studied as a function of the Tb mole-fraction. Our study suggests that the Tb incorporates mostly on the surface and affects the optical properties of the ZnO nanoparticles by influencing the attachment of certain adsorbed groups, which are found to be responsible for the appearance of a broad green luminescence (GL) band in the photoluminescence spectra recorded for these nanoparticles. It has been found that the accumulation of Tb on the surface of the nanoparticles not only enhances the band edge to green luminescence intensity ratio under the vacuum condition but also increases the band gap energy by introducing a hydrostatic compressive strain in individual nanoparticles, which provides a unique opportunity to study the pressure dependence of the optical properties of nanoparticles without applying any external pressure. The hydrostatic compressive strain is explained in terms of the increase of the surface strain energy as a result of the Tb accumulation on the surface of the nanoparticles. The average value of the surface energy density for the particles has been estimated as a function of Tb mole-fraction. The pressure coefficient of the band gap which is obtained from the variation of the band gap energy with the hydrostatic strain has been found to decrease significantly with the particle size for the ZnO nanoparticles.     

Influence of GaAsSb structural properties on the optical properties of InAs/GaAsSb quantum dots

The optical properties of InAs quantum dots with GaAsSb buffer, capping and cladding layers of different alloy compositions are studied by photoluminescence techniques. Fully strained GaAsSb layers show that the inclusion of a buffer layer gives a blue-shift to quantum dot emission, while for quantum dots capped with GaAsSb a clear red-shift is seen. Power-dependent photoluminescence suggests a transition from type-I to type-II can be achieved by GaAsSb at Sb composition between 11–13%, while the transition for the GaAsSb cladding layer occurs at around 11%. At low Sb composition, good crystal quality and energy barrier are detected by temperature-dependent photoluminescence, while high-level dislocation and defects exist under high antimony content, as evidenced by X-Ray Diffraction and Transmission Electron Microscopy.     

Influence of Fe-doping on the structural,optical and magnetic properties of ZnO nanoparticles

Zn_1–xFe_xO (x=0–0.05) nanoparticles were synthesized without a catalyst by a two-step method. Fe was doped into ZnO by a source of metallic Fe sheets in a solid–liquid system at 80 °C, and the Zn_1−xFe_xO nanoparticles were obtained by annealing at 300 °C. X-ray diffraction, X-ray photoelectron spectroscopy (XPS) and transmission electron microscopy were used to characterize the structural properties of the as-grown Zn_1−xFe_xO. The optical properties were determined by Infrared and Ultraviolet–visible spectroscopy. The results confirm that the crystallinity of the ZnO is deteriorated due to Fe-doping. XPS results show that there is a mixture of Fe⁰⁺ and the Fe³⁺ in the representative Zn_0.95Fe_0.05O sample. The optical band gap of Zn_1−xFe_xO is enhanced with increasing of Fe-doping. Room temperature ferromagnetism was observed in all the Fe-doped ZnO samples.     

Influence of synthesis conditions on the structural and optical properties of passivated silicon nanoclusters

First-principles molecular dynamics and quantum Monte Carlo techniques are employed to gain insight into the effect of preparation conditions on the structural and optical properties of silicon nanoparticles. Our results demonstrate that (i) kinetically limited nanostructures form different core structures than bulk-derived crystalline clusters, (ii) the type of core structure that forms depends on how the cluster is passivated during synthesis, and (iii) good agreement with measured optical gaps can be obtained for nanoparticles with core structures different from those derived from the bulk.     

Annealing temperature effect on the structural, optical and electrical properties of ZnS thin films

Zinc sulfide thin films were prepared on glass substrates at room temperature using a chemical bath deposition method. The obtained films were annealed at temperatures ranging from 100 to 500 °C in steps of 100 °C for 1 h. The films were characterized by X-ray diffraction (XRD), Raman spectroscopy, energy dispersive X-ray analysis (EDX), optical absorption spectra, and electrical measurements. X-ray diffraction analysis indicates that the deposited films have an amorphous structure, but after being annealed at 500 °C, they change to slightly polycrystalline. The optical constants such as the refractive index (n_r), the extinction coefficient (k), and the real (ε₁) and imaginary (ε₂) parts of the dielectric constant are calculated depending on the annealing temperature. Aside from the ohmic characteristics of the I-V curve, a nonlinear I-V curve owing to the Schottky contact is also found, and the barrier heights (?_bn) for Au/n-ZnS and In/n-ZnS heterojunctions are calculated. The conductivity type was identified by the hot-probe technique.     

Influence of annealing temperature on structural, optical and magnetic properties of Mn-doped ZnO thin films prepared by sol-gel method

Thin films of Zn_1−xMn_xO (x=0.01) diluted magnetic semiconductor were prepared on Si (1 0 0) substrates by the sol-gel method. The influence of annealing temperature on the structural, optical and magnetic properties was studied by X-ray diffraction (XRD), atom force microscopy (AFM), photoluminescence (PL) and SQUID magnetometer (MPMS, Quantum Design). The XRD spectrum shows that all the films are single crystalline with (0 0 2) preferential orientation along c-axis, indicating there are not any secondary phases. The atomic force microscopy images show the surfaces morphologies change greatly with an increase in annealing temperature. PL spectra reveal that the films marginally shift the near band-edge (NBE) position due to stress. The magnetic measurements of the films using SQUID clearly indicate the room temperature ferromagnetic behavior, and the Curie temperature of the samples is above room temperature. X-ray photoelectron spectroscopy (XPS) patterns suggest that Mn²⁺ ions were successfully incorporated into the lattice position of Zn²⁺ ions in ZnO host. It is also found that the post-annealing treatment can affect the ferromagnetic behavior of the films effectively.     

Influence of annealing temperature on structural and optical properties of ZnO: In thin films prepared by ultrasonic spray technique

Transparent conducting indium doped zinc oxide was deposited on glass substrate by ultrasonic spray method. The In doped ZnO samples with indium concentration of 3 wt.% were deposited at 300, 350 and 400 °C with 2 min of deposition time. The effects of substrate temperature and annealing temperature on the structural, electrical and optical properties were examined. The DRX analyses indicated that In doped ZnO films have polycrystalline nature and hexagonal wurtzite structure with (0 0 2) preferential orientation and the maximum average crystallite size of ZnO: In before and annealed at 500 °C were 45.78 and 55.47 nm at a substrate temperature of 350 °C. The crystallinity of the thin films increased by increasing the substrate temperature up 350 °C, the crystallinity improved after annealing temperature at 500 °C. The film annealed at 500 °C and deposited at 350 °C show lower absorption within the visible wavelength region. The band gap energy increased from E_g = 3.25 to 3.36 eV for without annealing and annealed films at 500 °C, respectively, indicating that the increase in the transition tail width. This is due to the increase in the electrical conductivity of the films after annealing temperature.     

Effects of buffer layer annealing temperature on the structural and optical properties of hydrothermal grown ZnO

ZnO was deposited on bare Si(1 0 0), as-deposited, and annealed ZnO/Si(1 0 0) substrates by hydrothermal synthesis. The effects of a ZnO buffer layer and its thermal annealing on the properties of the ZnO deposited by hydrothermal synthesis were studied. The grain size and root mean square (RMS) roughness values of the ZnO buffer layer increased after thermal annealing of the buffer layer. The effect of buffer layer annealing temperature on the structural and optical properties was investigated by photoluminescence, X-ray diffraction, atomic force microscopy, and scanning electron microscopy. Hydrothermal grown ZnO deposited on ZnO/Si(1 0 0) annealed at 750 °C with the concentration of 0.3 M exhibits the best structural and optical properties.     

Influence of substrate temperature and Cobalt concentration on structural and optical properties of ZnO thin films prepared by Ultrasonic spray technique

Pure and Cobalt doped zinc oxide were deposited on glass substrate by Ultrasonic spray method. Zinc acetate dehydrate, Cobalt chloride, 4-methoxyethanol and monoethanolamine were used as a starting materials, dopant source, solvent and stabilizer, respectively. The ZnO samples and ZnO:Co with Cobalt concentration of 2 wt.% were deposited at 300, 350 and 400 °C. The effects of substrate temperature and presence of Co as doping element on the structural, electrical and optical properties were examined. Both pure and Co doped ZnO samples are (0 0 2) preferentially oriented. The X-ray diffraction results indicate that the samples have polycrystalline nature and hexagonal wurtzite structure with the maximum average crystallite size of ZnO and ZnO:Co were 33.28 and 55.46 nm. An increase in the substrate temperature and presence doping the crystallinity of the thin films increased. The optical transmittance spectra showed transmittance higher than 80% within the visible wavelength region. The band gap energy of the thin films increased after doping from 3.25 to 3.36 eV at 350 °C.     

Influence of structural defects on the optical properties of strongly coupled Au nanoshell arrays

The effects of different defects on optical properties and plasmon resonances properties of Au nanoshell arrays were investigated by using the finite-difference time-domain(FDTD) theory.It is found that the optical properties of the nanoshell arrays are strongly influenced by different defects.We show that when the hollow Au nanoshell arrays are placed in air,there is a wide photonic band gap(PBG) in the infrared region,but the band gap becomes narrower as we introduced different defects.Based on the distributions of electric field component E z and the total energy distribution of the electric and the magnetic field,we show that there exhibit dipoles field distributions for the plasmon mode at the long-wavelength edge of the band gap,but composite higher order modes are excited at the short-wavelength edge of the band gap.The plasmon resonant modes also can be controlled by introducing defects.