Hydrogen storage in borohydrides Comparison of hydrolysis conditions of LiBH<Subscript>4</Subscript>, NaBH<Subscript>4</Subscript> and KBH<Subscript>4</Subscript>

The hydrogen storage capabilities of alkaline borohydrides through a hydrolyzing process were determined by taking into consideration the hydration of the end products. Comparison of LiBH₄, NaBH₄ and KBH₄ showed their storage capacities to be dependent on the composition of the metaborate formed. This composition is ruled by the hydrolysis conditions, especially the temperature reached during the reaction and the stability of the hydrates. The borohydride with the highest hydrogen content in the solid state, LiBH₄, could be less efficient than KBH₄ if the hydrolysis is performed at 120°C.     

Conductivity of molten LiF-ZrF<Subscript>4</Subscript>, NaF-ZrF<Subscript>4</Subscript>, KF-ZrF<Subscript>4</Subscript>, RbF-ZrF<Subscript>4</Subscript>, and CsF-ZrF<Subscript>4</Subscript> systems

Specific conductivity of molten salt mixtures of the LiF-ZrF₄, NaF-ZrF₄, KF-ZrF₄, RbF-ZrF₄, and CsF-ZrF₄ systems is measured in the whole concentration range using the reference capillary technique. The results are presented in the form of equations of the χ = a + bT + cT ² [S m^?1] type. The concentration dependences of molar conductivity are calculated on the basis of the density data. The obtained regularities are explained in the terms of the complex model of ion melt structures.     

Kinetics of Li-ion transfer reaction at LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript>, LiCoO<Subscript>2</Subscript>, and LiFePO<Subscript>4</Subscript> cathodes

Kinetics of LiFePO₄, LiMn₂O₄, and LiCoO₂ cathodes operating in 1 M LIPF₆ solution in a mixture of ethylene carbonate and dimethyl carbonate was deduced from impedance spectra taken at different temperatures. The most striking difference of electrochemical impedance spectroscopy (EIS) curves is the impedance magnitude: tens of ohms in the case of LiFePO₄, hundreds of ohms for LiMn₂O₄, and thousands of ohms for LiCoO₂. Charge transfer resistances (R _ct) for lithiation/delitiation processes estimated from the deconvolution procedure were 6.0 Ω (LiFePO₄), 55.4 Ω (LiCoO₂), and 88.5 Ω (LiMn₂O₄), respectively. Exchange current density for all the three tested cathodes was found to be comparable (0.55–1·10^?2 mAcm^?2, T = 298 K). Corresponding activation energies for the charge transfer process, \( {E}_{ct}^{\#} \), differed considerably: 66.3, 48.9, and 17.0 kJmol^?1 for LiMn₂O₄, LiCoO₂, and LiFePO₄, respectively. Consequently, temperature variation may have a substantial influence on exchange current densities (j _o) in the case of LiMn₂O₄ and LiCoO₂ cathodes.     

Study on chemisorption of H<Subscript>2</Subscript>, O<Subscript>2</Subscript>, CO and C<Subscript>2</Subscript>H<Subscript>4</Subscript>on Pt-Ag/SiO<Subscript>2</Subscript>catalysts by microcalorimetry and FTIR

Adsorption microcalorimetry has been employed to study the interaction of ethylene with the reduced and oxidized Pt-Ag/SiO₂catalysts with different Ag contents to elucidate the modified effect of Ag towards the hydrocarbon processing on platinum catalysts. In addition, microcalorimetric adsorption of H₂, O₂, CO and FTIR of CO adsorption were conducted to investigate the influence of Ag on the surface structure of Pt catalyst. It is found from the microcalorimetric results of H₂and O₂adsorption that the addition of Ag to Pt/SiO₂leads to the enrichment of Ag on the catalyst surface which decreases the size of Pt surface ensembles of Pt-Ag/SiO₂catalysts. The microcalorimetry and FTIR of CO adsorption indicates that there still exist sites for linear and bridged CO adsorption on the surface of platinum catalysts simultaneously although Ag was incorporated into Pt/SiO₂. The ethylene microcalorimetric results show that the decrease of ensemble size of Pt surface sites suppresses the formation of dissociative species (ethylidyne) upon the chemisorption of C₂H₄on Pt-Ag/SiO₂. The differential heat vs. uptake plots for C₂H₄adsorption on the oxygen-preadsorbed Pt/SiO₂and Pt-Ag/SiO₂catalysts suggest that the incorporation of Ag to Pt/SiO₂could decrease the ability for the oxidation of C₂H₄.     

Five-component reciprocal systems Na,K∥Cl,CO<Subscript>3</Subscript>,MoO<Subscript>4</Subscript>,WO<Subscript>4</Subscript> and Na,K∥F,CO<Subscript>3</Subscript>,MoO<Subscript>4</Subscript>,WO<Subscript>4</Subscript>

Five-component reciprocal systems Na,K∥Cl,CO₃,MoO₄,WO₄ and Na,K∥F,CO₃,MO₄,WO₄ have been studied by differential thermal analysis (DTA) and X-ray powder diffraction (XPD). The systems have been triangulated to phase simplexes. The main reciprocal and complex-formation reactions have been revealed. The stability of [Na,K]₂CO₃, Na₂[Mo,W]O₄, and K₂[Mo,W]O₄ binary solid solutions and the nonexistence of quintuple invariant points in the title systems have been verified.     

Solid-phase synthesis of intermetallic compounds Al<Subscript>13</Subscript>Co<Subscript>4</Subscript>, Al<Subscript>13</Subscript>Fe<Subscript>4</Subscript>, and Al<Subscript>13</Subscript>Co<Subscript>2</Subscript>Fe<Subscript>2</Subscript>

Intermetallic compounds Al₁₃Co₄, Al₁₃Fe₄, and Al₁₃Co₂Fe₂ were obtained by solid-phase synthesis in air at temperatures below 600°C using precursor metals subjected to mechanochemical preactivation. The phase composition of the synthesized aluminides and composites Al₁₃Co₄/SiO₂ and Al₁₃Fe₄/SiO₂ was analyzed.     

A Systemic DFT Study on Several 5<Emphasis Type="Italic">d</Emphasis>-Electron Element Dimers: Hf<Subscript>2</Subscript>, Ta<Subscript>2</Subscript>, Re<Subscript>2</Subscript>, W<Subscript>2</Subscript>, and Hg<Subscript>2</Subscript>

Eleven kinds of density functionals in conjunction with three different basis sets are employed to investigate the homonuclear 5d-electron dimers: Hf₂, Ta₂, Re₂, W₂ and Hg₂. The computed bond lengths, vibrational frequencies and dissociation energies of these molecules are used to compare with available experimental data to find the appropriate combination of functional and basis set. The different functionals and basis sets favor different ground electronic state for Hf₂ and Re₂ molecules, indicating that these two dimers are sensitive to the functionals used. The molecular properties of Hg₂ dimer depend strongly on both functionals and basis sets used. It is found that the BP86 and PBEPBE functionals are generally successful in describing the 5d-electron dimers. For the ground states of these dimers, the bonding patterns are determined by natural bond orbital (NBO) analysis. Natural electron configurations show that the 6s and 5d orbitals in the bonding atoms hybrid with each other for the studied dimers except for Hg₂.     

Quantum-chemical study of adsorption of Ag<Subscript>2</Subscript>, Ag<Subscript>4</Subscript>, and Ag<Subscript>8</Subscript> on different parts of the TiO<Subscript>2</Subscript> surface

Quantum-chemical study of the adsorption of two-, four- and eight-atomic silver clusters on stoichiometric and partially reduced rutile (110) surface, and of silver tetramer on the surface of anatase (101) was carried out in the framework of periodic DFT model. The most energetically favorable positions of clusters on the surface of TiO₂ and the mechanism of binding the clusters with the substrate were revealed. According to the calculations, the adsorption of silver clusters on the surface of stoichiometric rutile (110) is more preferable than on the partially reduced one. The mechanism of binding the clusters with the surface of anatase and rutile is shown to be similar.     

One-pot synthesis of diphenyl pyrazolylmethylanilines via reductive amination using NaBH<Subscript>4</Subscript>/I<Subscript>2</Subscript> and their antimicrobial screening

Abstract  

Direct reductive amination of 1,3-diphenyl-1H-pyrazole-4-carbaldehyde and 3-(4-methylphenyl)-1-phenyl-1H-pyrazole-4-carbaldehyde with various substituted aromatic amines using NaBH₄ in the presence of I₂ as reducing agent is described. The reaction has been carried out in anhydrous methanol under neutral conditions at room temperature. The structure of newly synthesized diphenyl pyrazolylmethylanilines was established on the basis of IR, ¹H, ¹³C NMR, and mass spectral data. All diphenyl pyrazolylmethylaniline derivatives were tested in vitro for their antifungal and antibacterial activity against different strains of fungi and bacteria. Most of the compound exhibited considerable antifungal activity but poor antibacterial activity against the test strains.     

Thermal analysis on C<Subscript>6</Subscript>H<Subscript>10</Subscript>Ge<Subscript>2</Subscript>O<Subscript>7</Subscript>-doped MgB<Subscript>2</Subscript>

Additives to MgB₂ can improve the superconducting functional characteristics, such as critical current density (J _c) and irreversibility field (H _irr). Recently, we have shown that repagermanium (C₆H₁₀Ge₂O₇) is an effective additive, enhancing both J _c and H _irr. To look into details of the processes taking place during the reactive sintering, a thermal analysis study (0.167 K s^?1, in Ar) is reported. We used differential scanning calorimetry between 298 and 863 K and simultaneous thermogravimetric—differential thermal analysis between 298 and 1233 K. Samples were mixtures of powders with composition 97 mol% MgB₂ and 3 mol% C₆H₁₀Ge₂O₇. Up to 863 K, repagermanium decomposes by multiple steps and forms amorphous phases. A reaction with MgB₂ is not observed. Above this temperature, partial decomposition of MgB₂ occurs. Crystalline Ge and MgO are detected before formation of Mg₂Ge and MgB₄, when temperature approaches the melting point of Ge (1211 K). Carbon substitution for boron in the crystal lattice of MgB₂ is observed for samples heated above 863 K. The amount of substitutional C does not significantly change with temperature.     

Electronic energy structure of As<Subscript>2</Subscript>S<Subscript>3</Subscript>, AsSI,AgAsS<Subscript>2</Subscript>, and TiS<Subscript>2</Subscript> semiconductors

Quantum-mechanical calculations with the FEFF8 code were used to study the electronic energy structure of 200-atomic clusters of As₂S₃, AsSI, AgAsS₂, and TiS₂ semiconductor compounds. The calculated local partial densities of electronic states are compared with the sulfur K and L X-ray emission spectra and sulfur K absorption spectra for fine powders of these compounds. Good agreement between theory and experiment has been obtained.     

Cobalt boride catalysts for hydrogen storage systems based on NH<Subscript>3</Subscript>BH<Subscript>3</Subscript> and NaBH<Subscript>4</Subscript>

The catalytic activity of cobalt borides forming in situ under conditions of NH₃BH₃ and NaBH₄ hydrolysis have been investigated. The reaction properties of the catalysts depend on the nature of the hydride. According to high-temperature X-ray diffraction, thermal analysis, high-resolution transmission electron microscopy, IR spectroscopy, and chemical analysis data, the nature of the hydride determines the particle size, chemical composition, and crystallization properties of the cobalt borides.     

Reactions of Cr atoms with NO,N<Subscript>2</Subscript>O,CO<Subscript>2</Subscript>, NO<Subscript>2</Subscript>, and SO<Subscript>2</Subscript> molecules

Experimental results on the interaction of Cr atoms with various oxygen-containing molecules (NO, N₂O, CO₂, NO₂, and SO₂) at high temperatures (>1000 K) are presented. It is demonstrated that activation barrier for spin-forbidden reactions is higher, all other things being equal. For the reaction of Cr atoms with N₂O, an interpolated temperature dependence of the rate constant, based on the high-temperature measurements conducted in the present work and the published low-temperature data, is proposed.     

Thermochemical study of gaseous salts of oxygen-containing acids: XXIII. Molecules MnB<Subscript>2</Subscript>O<Subscript>4</Subscript>, MnNbO<Subscript>2</Subscript>, MnNbO<Subscript>3</Subscript> and MnTiO<Subscript>3</Subscript>

Gas-phase equilibria involving manganese borate, niobates, and titanate were studied. Standard enthalpies of formation and atomization of the gaseous molecules MnB₂O₄, MnNbO₂, MnNbO₃, and MnTiO₃ were determined.     

Benzene Adsorption on C<Subscript>24</Subscript>, Si@C<Subscript>24</Subscript>, Si-Doped C<Subscript>24</Subscript>, and C<Subscript>20</Subscript> Fullerenes

The absorption feasibility of benzene molecule in the C₂₄, Si@C₂₄, Si-doped C₂₄, and C₂₀ fullerenes has been studied based on calculated electronic properties of these fullerenes using Density functional Theory (DFT). It is found that energy of benzene adsorption on C₂₄, Si@C₂₄, and Si-doped C₂₄ fullerenes were in range of –2.93 and –51.19 kJ/mol with little changes in their electronic structure. The results demonstrated that the C₂₄, Si@C₂₄, and Si-doped C₂₄ fullerenes cannot be employed as a chemical adsorbent or sensor for benzene. Silicon doping cannot significantly modify both the electronic properties and benzene adsorption energy of C₂₄ fullerene. On the other hand, C₂₀ fullerene exhibits a high sensitivity, so that the energy gap of the fullerene is changed almost 89.19% after the adsorption process. We concluded that the C₂₀ fullerene can be employed as a reliable material for benzene detection.     

The interaction of CH<Subscript>3</Subscript>Cl,CH<Subscript>2</Subscript>Cl<Subscript>2</Subscript>, CHCl<Subscript>3</Subscript>, and CCl<Subscript>4</Subscript> with ozone on the surface of ice under stratospheric conditions

The interaction of ozone with chlorinated methanes adsorbed on a thin ice film was studied over the temperature range 77–292 K. Ozone was shown to oxidize chlorinated methanes starting with 210 K to produce chlorine oxides of various compositions. The products formed in the oxidation of chlorinated methanes with ozone over the temperature range 77–292 K were analyzed by IR Fourier transform spectroscopy. Along with carbon dioxide and water, chlorine oxides in high oxidation states were predominantly formed.     

Solubility of YF<Subscript>3</Subscript>, CeF<Subscript>3</Subscript>, PrF<Subscript>3</Subscript>, NdF<Subscript>3</Subscript>, and DyF<Subscript>3</Subscript> in solutions containing sulfuric and phosphoric acids

The solubility of YF₃, CeF₃, PrF₃, NdF₃, and DyF₃ in solutions containing 0–4.496% mol/L (0–35 wt %) of H₂SO₄ and 0–27.6 g/L of H₃PO₄ (0–20 g/L of P₂O₅) at 20 °C was determined. Higher solubility in sulfuric acid solutions compared to that in hydrochloric and phosphoric acid solutions was attributed to the formation of fluorosulfate complexes M₂(SO₄)F₄(M = Y, Ce, Pr, Nd, Dy). The effect of minor concentrations of the phosphate ions on the solubility of YF₃, CeF₃, PrF₃, NdF₃, and DyF₃ in sulfuric acid solutions and the effect of fluoride ions on the recovery of lanthanides during sulfuric acid leaching from the phosphohemihydrate were discussed.     

Comparison of the Solubility of ZnFe<Subscript>2</Subscript>O<Subscript>4</Subscript>, Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> and Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> in High Temperature Water

As the solubility is a direct measure of stability, this study compares the solubilities of ZnFe₂O₄, Fe₃O₄ and Fe₂O₃ in high temperature water. Through literature analysis and formula derivation, it is shown that it is reasonable to assume ZnFe₂O₄ and Fe(OH)₃ coexist when ZnFe₂O₄ is dissolved in water. Results indicated that the solubility of ZnFe₂O₄ is much lower than that of Fe₂O₃ or Fe₃O₄. The low solubility of ZnFe₂O₄ indicates that it is more protectively stable as an anticorrosion phase. Moreover, the gap between the solubility of ZnFe₂O₄ and that of Fe₃O₄ or Fe₂O₃ was enlarged with an increase of temperature. This means that ZnFe₂O₄ is more protective at higher temperatures. Further analysis indicated that with the increase of temperature, the solubility of ZnFe₂O₄ changed little while those of Fe₂O₃ or Fe₃O₄ changed a lot. Little change of the solubility of ZnFe₂O₄ with increase of temperature showed that ZnFe₂O₄ is stable. The very low and constant solubility of ZnFe₂O₄ suggests that it is more protective than Fe₂O₃ and Fe₃O₄, especially in water at higher temperature.     

Three-component systems LiBr-LiVO<Subscript>3</Subscript>-Li<Subscript>2</Subscript>MoO<Subscript>4</Subscript> and LiBr-Li<Subscript>2</Subscript>SO<Subscript>4</Subscript>-Li<Subscript>2</Subscript>MoO<Subscript>4</Subscript>

Phase equilibria in the three-component systems LiBr-LiVO₃-Li₂MoO₄ and LiBr-Li₂SO₄-Li₂MoO₄ have been studied using differential thermal analysis (DTA). Eutectic compositions have been determined (mol %): in the system LiBr-LiVO₃-Li₂MoO₄, 56.0 LiBr, 22.0 LiVO₃, and 22.0 Li₂MoO₄ with a melting temperature of 413°C; and in the system LiBr-Li₂SO₄-Li₂MoO₄, 65.0 LiBr, 14.0 Li₂SO₄, and 21.0 Li₂MoO₄ with a melting temperature of 421°C. Phase fields have been demarcated.