Nanopatterning of mesoporous inorganic oxide films for efficient light harvesting of dye-sensitized solar cells

Nanopatterning provides facile process to well-arrayed mesoporous inorganic oxide films at low cost by using readily available pastes and elastomeric nanostamps. The fabricated nanopattern boosted the light-harvesting efficiency of dye-sensitized solar cells (DSSCs) by a light-trapping technique. The iodine-free solid-state DSSCs showed a 40 % increase in the current density and high efficiency (7.03 %).     

Photovoltaic activity of Ti/MCM‐41

Ti/MCM‐41 is a well‐known heterogeneous catalyst for alkene epoxidation with organic peroxides. This titanosilicate contains isolated titanium atoms forming part of a framework of mesoporous silica whose structure is formed by parallel hexagonal channels 3.2 nm in diameter. The surface area and porosity of Ti/MCM‐41 are about 880 m² g^?1 and 0.70 cm³ g^?1, respectively. These values are among the highest for any material. Herein, we show that Ti/MCM‐41 exhibits photovoltaic activity. Dye‐sensitized solar cells using mesoporous Ti/MCM‐41 (2.8–5.7 % Ti content) as active layer, black dye N3 as photosensitizer and I₃^?/I^? in methoxyacetonitrile as electrolyte exhibit a V_OC, J_SC and FF of 0.44 V, 0.045 mA cm^?2 and 0.33, respectively. These values compare well against 0.75 V, 4.1 mA cm^?2 and 0.64, respectively, measured for analogous solar cells using conventional P‐25 TiO₂. However, the specific current density (J_SC/Ti atom) for the Ti/MCM‐41 is very similar to that of P25 TiO₂.     

Hydrothermal fabrication of quasi-one-dimensional single-crystalline anatase TiO2 nanostructures on FTO glass and their applications in dye-sensitized solar cells

One-dimensional and quasi-one-dimensional semiconductor nanostructures are desirable for dye-sensitized solar cells (DSSCs), since they can provide direct pathways for the rapid collection of photogenerated electrons, which could improve the photovoltaic performance of the device. Quasi-1D single-crystalline anatase TiO(2) nanostructures have been successfully prepared on transparent, conductive fluorine-doped tin oxide (FTO) glass with a growth direction of [101] through a facile hydrothermal approach. The influences of the initial titanium n-butoxide (TBT) concentration, hydrothermal reaction temperature, and time on the length of quasi-1D anatase TiO(2) nanostructures and on the photovoltaic performance of DSSCs have been investigated in detail. A power conversion efficiency of 5.81% has been obtained based on the prepared TiO(2) nanostructure photoelectrode 6.7 μm thick and commercial N719 dye, with a short-circuit current density of 13.3 mA cm(-2) , an open-circuit voltage of 810 mV, and a fill factor of 0.54.     

Transition from anodic titania nanotubes to nanowires: arising from nanotube growth to application in dye-sensitized solar cells

Anodic formation of titania nanowires has been interpreted using a bamboo-splitting model; however, a number of phenomena are difficult to explain with this model. Herein, transition from nanotubes to nanowires is investigated by varying the anodizing conditions. The results indicate that the transition requires a large number of hydrogen ions to reduce the passivated area of tube walls, and therefore can be observed only in an intermediate chemical dissolution environment. Accordingly, a model in terms of stretching and splitting is proposed to interpret the transition process. The model provides a basis to suppress the nanowires with surface treatments before anodization and to clear the nanowires with an ultrasonication process after anodization. The nanotube-nanowire transition also arises when the tubes are directly used in dye-sensitized solar cells. Treatment with titanium tetrachloride solution for about 10 h is found to be effective in suppressing the nanowires, and thus improving the photovoltaic properties of the solar cells.     

Improved conversion efficiency in dye-sensitized solar cells based on electrospun Al-doped ZnO nanofiber electrodes prepared by seed layer treatment

The application of electrospun nanofibers in electronic devices is limited due to their poor adhesion to conductive substrates. To improve this, a seed layer (SD) is introduced on the FTO substrate before the deposition of the electrospun composite nanofibers. This facilitates the release of interfacial tensile stress during calcination and enhances the interfacial adhesion of the AZO nanofiber films with the FTO substrate. Dye-sensitized solar cells (DSSC) based on these AZO nanofiber photoelectrodes have been fabricated and investigated. An energy conversion efficiency (η) of 0.54-0.55% has been obtained under irradiation of AM 1.5 simulated sunlight (100 mW/cm²), indicating a massive improvement of η in the AZO nanofiber film DSSCs after SD-treatment of the FTO substrate as compared to those with no treatment. The SD-treatment has been demonstrated to be a simple and facile method to solve the problem of poor adhesion between electrospun nanofibers and the conductive substrate.     

Asymmetric ZnO Panel‐Like Hierarchical Architectures with Highly Interconnected Pathways for Free‐Electron Transport and Photovoltaic Improvements

Through a rapid and template‐free precipitation approach, we synthesized an asymmetric panel‐like ZnO hierarchical architecture (PHA) for photoanodes of dye‐sensitized solar cells (DSCs). The two sides of the PHA are constructed differently using densely interconnected, mono‐crystalline and ultrathin ZnO nanosheets. By mixing these PHAs with ZnO nanoparticles (NPs), we developed an effective and feasible strategy to improve the electrical transport and photovoltaic performance of the composite photoanodes of DSCs. The highly crystallized and interconnected ZnO nanosheets largely minimized the total grain boundaries within the composite photoanodes and thus served as direct pathways for the transport and effective collection of free electrons. Through low‐temperature (200 °C) annealing, these novel composite photoanodes achieved high conversion efficiencies of up to 5.59 % for ZnO‐based quasi‐solid DSCs.     

High dispersion Pt nanoparticles using mesoporous carbon support for enhancing conversion efficiency of dye-sensitized solar cells

<正>Mesoporous carbon(MC) with surface area of 380 m~2/g was prepared and employed as the carbon support of Pt catalyst for counter electrode of dye-sensitized solar cells.Pt/MC samples containing 1 wt%Pt were prepared by reducing chloroplatinic acid on MC using wet impregnation.It was found that Pt nanoparticles were uniform in size and highly dispersed on MC supports.The average size of Pt nanoparticles is about 3.4 nm.Pt/MC electrodes were fabricated by coating Pt/MC samples on fluorine-doped tin oxide glass.The overall conversion efficiency of dye-sensitized solar cells with Pt/MC counter electrode is 6.62%,which is higher than that of the cells with conventional Pt counter electrode in the same conditions.     

Template‐free synthesis of polyaniline nanobelts as a catalytic counter electrode in dye‐sensitized solar cells

Polyaniline (PAn) nanobelts were synthesized by simply mixing aniline and hydrochloric acid aqueous solution with ammonium peroxydisulfate and hydrochloric acid aqueous solution at room temperature without any templates. The PAn nanobelt paste with polytetrafluoroethylene as binder is proper for low‐cost and efficient casting processes such as doctor blade method, screen printing, spin‐casting, and even roll‐to‐roll painting. The porous network structure of the PAn nanobelt counter electrode was obtained after drying the paste on the conductive glass. The as‐prepared PAn nanobelt counter electrode showed nearly equivalent electrochemical catalytic activity as that of thermal decomposed Pt counter electrode, owing to the well‐connected conductive network and high active surface area. The power conversion efficiency of dye‐sensitized solar cell with PAn nanobelt counter electrode attained 90% of the value of the cell with Pt counter electrode. Copyright © 2014 John Wiley & Sons, Ltd.     

Molecular design of organic dyes based on vinylene hexylthiophene bridge for dye-sensitized solar cells

Three donor-(π-spacer)-acceptor (D-π-A) organic dyes, containing different groups (triphenylamine, di(p-tolyl)phenylamine, and 9-octylcarbazole moieties) as electron donors, were designed and synthesized. Nanocrystalline TiO₂ dye-sensitized solar cells were fabricated by using these dyes. It was found that the variation of electron donors in the D-π-A dyes played an important role in modifying and tuning photophysical properties of organic dyes. Under standard global AM 1.5 solar condition, the DSSC based on the dye D2 showed the best photovoltaic performance: a short-circuit photocurrent density (J _sc ) of 13.93 mA/cm², an open-circuit photovoltage (V _oc ) of 0.71 V, and a fill factor (FF) of 0.679, corresponding to solar-to-electric power conversion efficiency (η) of 6.72%. Supported by the Key Project of Hunan Province of China (Grant No. 2008FJ2004), Natural Science Foundation of Hunan Province of China (Grant Nos. 09JJ3020 & 09JJ4005), and Scientific Research Fund of Hunan Provincial Education Department (Grant No. 08C888).     

静电喷雾法制备高效染料敏化太阳能电池的二氧化钛光阳极

TiO2光阳极膜是染料敏化太阳能电池（DSSC）的核心部件之一,它对电池的光电转换效率起决定性作用．TiO2电极一般采用刮涂法和丝网印刷法制备．近3年,通过静电喷雾制备光阳极的方法得到国内外学者的关注．静电喷雾制备光阳极会受到多种因素的影响,如电压、流速、悬浮液浓度、喷雾距离以及喷雾时间等．但这些因素对成膜和DSSC器件性能的影响却没有得到全面的研究或者报道．本文使用静电喷雾法制备了多孔TiO2纳米膜,并研究了以其为电极的电池器件特性．经过超声充分分散的稳定TiO2乙醇悬浮液在高电压下喷雾到导电玻璃上成膜．通过改变电喷雾距离,得到了具有不同形貌的TiO：光阳极膜,并解释了其形成的机理及其对电池性能的影响．研究还表明,光阳极膜的TiC14处理能够很好地改善电池性能．通过优化,基于流速为0．8mL／h、电喷雾距离和时间分别为2．2cm和8min条件下制备的光阳极,结合TiC14处理,组装的电池在模拟太阳光源AM1．5G下光电转化效率达6．24％．     

Synthesis of organic sulfobetaine‐based polymer gel electrolyte for dye‐sensitized solar cell application

We have synthesized eco‐friendly, economic, and equally efficient polysulfobetaine‐based gel electrolyte to the alternative of liquid electrolyte in the fabrication of dye‐sensitized solar cells (DSSCs) for the first time. This nitrogen‐rich and highly conductive polysulfobetaine was synthesized by an easy and facile method without the use of any catalyst and explored for its DSSC application. The synthesized polymer gel electrolyte exhibited good ionic conductivity about 6.8 × 10^?3 Scm^?1 at ambient temperatures. DSSCs were fabricated based on this polysulfobetaine gel electrolyte and studied for their performance based on photovoltaic parameters. The DSSC photovoltaic results were appreciable and are Voc = 0.82 V, Jsc = 11.49 mA/cm², FF = 66%, and PCE = 6.26% at 1 sun intensity. These values are slightly lower than conventional liquid electrolyte‐based DSSC shown as Voc = 0.78 V, Jsc = 12.90 mA/cm², FF = 69%, and PCE = 7.07%, both at 100 mWcm^?2. Conductivity and photovoltaic parameters of the device reveals that as prepared polysulfobetaine‐based polymer gel electrolyte may be useful in the fabrication of DSSC and other electrochemical devices. Copyright © 2017 John Wiley & Sons, Ltd.     

Theoretical study of quinolines-I(2) intermolecular interaction and implications on dye-sensitized solar cell performance

The monomer and intermolecular charge-transfer complexes of 13 different quinoline derivatives with diiodine were studied using ab initio molecular orbital (MO) and density functional theory (DFT) methods. Calculations revealed that the sigma* orbital of iodine interacts with the nitrogen lone pair in the quinoline ring. The open-circuit photovoltage (V(oc)) values of an Ru(II) complex dye-sensitized nanocrystalline TiO(2) solar cell with an I(-)/I(3) (-) redox electrolyte in acetonitrile using quinoline additives were compared to the computational calculations on the intermolecular interaction between quinolines and I(2). The optimized geometries, frequency analyses, Mulliken population analyses, natural bond orbital (NBO) analyses, and interaction energies indicate that the V(oc) value of the solar cell is higher when quinoline complexes more favorably interact with I(2). Therefore, the interaction between the quinoline additives and iodine redox electrolyte is an important factor for controlling dye-sensitized solar cell performance.     

Electrochemical impedance characterization and photovoltaic performance of N719 dye‐sensitized solar cells using quaternized ammonium iodide containing polyfluorene electrolyte solutions

This study develops a series of titanium oxide electrode‐based N719 dye‐sensitized solar cells (DSSCs) using quaternized ammonium iodide containing main‐chain and star‐shaped polyfluorene (MPF‐E and SPF‐E) electrolyte solutions. The electrochemical impedance and photovoltaic properties of the polyfluorene electrolyte‐based DSSCs were studied and compared to those of the poly(ethylene oxide) (PEO) electrolyte‐based DSSCs. As with the PEO electrolyte‐based DSSCs, the recombination impedance increased with increase in the polymer content for the MPF‐E electrolyte‐based DSSCs, whereas the photovoltaic performance did otherwise. Nevertheless, the reduction in the photovoltaic properties was not significant for the SPF‐E electrolyte‐based DSSCs. The electrochemical impedance and photovoltaic properties of the different polymer‐based DSSCs are also discussed as a function of the polymer concentration. Copyright © 2010 John Wiley & Sons, Ltd.     

Room temperature polymerization of poly(3,4‐ethylenedioxythiophene) as transparent counter electrodes for dye‐sensitized solar cells

Poly(3,4‐ethylenedioxythiophene) (PEDOT) counter electrode is prepared with in situ polymerization of 3,4‐ethylenedioxythiophene on a fluorine‐doped tin oxide over‐layer glass at room temperature. The cyclic voltammetry, electrochemical impedance spectroscopy, and Tafel polarization are measured to evaluate the catalytic activity of PEDOT counter electrode for I₃^?/I^? redox couple. Comparing the data with that of traditional thermal decomposed Pt counter electrode, it is found that PEDOT has higher catalytic activity than that of Pt counterpart. Power conversion efficiency of the dye‐sensitized solar cell (DSC) with PEDOT counter electrode can attain to 7.713%, a little higher than that of the cell with Pt counter electrode (7.300%). Taking the advantage of high transparency of PEDOT counter electrode, an Ag mirror is put on the back side of PEDOT counter electrode of the DSC to reflect light back for power conversion. Power conversion efficiency of the DSC with this special structure can be further enhanced to 8.359%, which mainly stems from the improved short‐circuit current density by the increased irradiated light intensity. Copyright © 2014 John Wiley & Sons, Ltd.     

Preparation of chemically sintered ZnO films and their application in dye sensitized solar cells formed on plastic substrates

Meso-porous zinc oxide films were prepared on tin-doped indium oxide-coated, polyethelene naphthalate substrates from binder-free ZnO slurry. The reaction with ammonium hydroxide was found to increase connection between ZnO grains by forming a nano-rod like structure followed by heating at 150 °C. The enhancement of adhesion among ZnO grains was evaluated using a nano-scratch technique. Two different xanthene dyes were used to sensitize ZnO electrodes, with a photo-voltage of 657 mV, fill-factor of 73% and photo-current of 4.1 mA cm⁻² with a maximum light to-electrical energy conversion efficiency of 2.0% being obtained for the plastic based ZnO|mercurochrome|electrolyte solar cell under 1 sun.     

三苯胺类染料敏化太阳能电池能量转化效率的全息定量构效关系研究

研究构建了三苯胺类化合物分子结构与相应染料敏化太阳能电池能量转化效率(PCE)之间的全息定量构效关系(HQSAR)模型。当fragment distinction、fragment size、hologram length和principal components分别为“C、DA”、“4-7”、“199”和“6”时,可以获得最优HQSAR模型。采用外部测试集验证和留一交叉验证对所建立模型进行检验,外部测试集验证中CCC和 Q2F3分别为0.933和0.892,留一交叉验证中其q2cv和r2分别为0.791和0.902,表明所建立模型具有较好的拟合效果和预测能力。通过所建立HQSAR模型的分子贡献图可知,环戊并二噻吩基团的存在有利于提高PCE值,长烷基链的存在可能降低PCE值。