Enhanced electrochemical properties of polyethylene oxide-based composite solid polymer electrolytes with porous inorganic–organic hybrid polyphosphazene nanotubes as fillers

Solid composite polymer electrolytes consisting of polyethylene oxide (PEO), LiClO₄, and porous inorganic–organic hybrid poly (cyclotriphosphazene-co-4, 4′-sulfonyldiphenol) (PZS) nanotubes were prepared using the solvent casting method. Differential scanning calorimetry and scanning electron microscopy were used to determine the characteristics of the composite polymer electrolytes. The ionic conductivity, lithium ion transference number, and electrochemical stability window can be enhanced after the addition of PZS nanotubes. The electrochemical impedance showed that the conductivity was improved significantly. Maximum ionic conductivity values of 1.5 × 10⁻⁵ S cm⁻¹ at ambient temperature and 7.8 × 10⁻⁴ S cm⁻¹ at 80 °C were obtained with 10 wt.% content of PZS nanotubes, and the lithium ion transference number was 0.35. The good electrochemical properties of the solid-state composite polymer electrolytes suggested that the porous inorganic–organic hybrid polyphosphazene nanotubes had a promising use as fillers in SPEs and the PEO₁₀–LiClO₄–PZS nanotube solid composite polymer electrolyte might be used as a candidate material for lithium polymer batteries.     

PEO/P(VdF-HFP) blend based Li+ ion-conducting composite polymer electrolytes dispersed with dedoped (insulating) polyaniline nanofibers

Composite polymer electrolyte membranes composed of poly(ethylene oxide) (PEO), poly(vinylidene fluoride-hexafluoropropylene) {P(VdF-HFP)} blends, dedoped (insulating) polyaniline (PAni) nanofibers, and LiClO₄ as salt have been synthesized with varying fraction of dedoped PAni nanofibers (from 2 to 10 wt.%). The ionic conductivity of PEO–P(VdF-HFP)–LiClO₄ electrolyte system increases with increase in the fraction of dedoped polyaniline nanofibers. This could be attributed to the incorporation of nanofibers (aspect ratio >50), which may provide high ion conducting path along the interface due to Lewis acid–base interactions between Li⁺ ions and lone pair of electrons of nitrogen atom of polyaniline. However, at higher fraction (>6 wt.%), the nanofibers get phase separated from the polymer matrix and form domain-like structures, which may act as physical barrier to the conduction of Li⁺ ions resulting in decreased ionic conductivity. Electrochemical potential window and interfacial stability of nanofibers dispersed polymer electrolyte membranes are also better than that of nanofibers free membranes.     

An electrochemically prepared sky-blue light emitting ether functionalized polyfluorene as chemosensor for metal ions

Synthesis and electrochemical polymerization of 9,9-bis(2-(2-(2-methoxy ethoxy)ethoxy)ethyl)-fluorene(EO-F)into poly[9,9-bis(2-(2-(2-methoxy ethoxy)ethoxy)ethyl)-fluorene](EO-PF) films are reported. The boron trifluoride diethyl etherate electrolyte enables facile preparation of EO-PF films at lower potential compared to LiClO4/MeCN and the electrochemical polymerizations are discussed. The EO-PF shows good electrochemical behavior and can be dissolved in solvents such as DMSO and THF. The solubility of EO-PF in THF is 2 mg mL 1and the number average molecular weight is35300 with a polydispersity index of 1.65. The side chains on C9position of the monomer maintain unchanged after electrooxidation into corresponding polymer. The EO-PF dissolved in THF under 365 nm ultraviolet light is sky blue light emitting with the Commission Internationale de L Eclairage-CIE coordinates of(0.19, 0.15). The electropolymerized EO-PF is used for the first time in chemosensing metal ions, demonstrating fluorescence quenching for Mn2+and Fe3+while fluorescence enhancement for Cr6+ions.     

Segmental mobility and relaxation processes of Fe2O3 nanoparticle-loaded fast ionic transport nanocomposite gel polymer electrolyte

The interaction of Fe₂O₃ nanoparticles emphasized between poly(propylene glycol) (PPG 4000) and silver triflate (AgCF₃SO₃) on the conformal changes of coordination sites and the electrochemical properties have been investigated. On the influence of Fe₂O₃ nanoparticles distribution, the interactions between the ether oxygen in C–O–C of the polymer chain with Ag⁺ ion as a result of bond strength of the C–O–C stretching vibration, the end group effect has been examined by Fourier transform infrared (FT-IR) spectroscopy. The formation of transient cross-links between polymer chains and filler particles appears to be a characteristic change in the glass transition temperature (T _g) and enhance the effective number of cations as well. The strength of ion–polymer interactions was revealed by the transport of ions, t _Ag+, and found to be in the range of 0.42–0.50, and the ionic conductivity was ascertained by complex impedance analysis with a maximum of 9.2?×?10^?4 S cm^?1 at 298 K with a corresponding concentration of 10 wt% Fe₂O₃ nanoparticles. The temperature dependence of conductivity has been examined based on the Vogel–Tammann–Fulcher (VTF) equation, thereby suggesting the segmental chain motion and free volume changes. From the impedance data, both the dielectric and modulus behaviours have been revealed and both were well correlated as a function of frequency.     

Effects of dopant anions and N-substituents on the electrochemical behavior of polypyrrole films in propylene carbonate solution

The electrochemical properties of poly(N-ethylpyrrole) (PEPy) and poly(N-methylpyrrole) (PMPy) films in propylene carbonate (PC) solution, where ion transport is anion-specific, has been investigated using the cyclic electrochemical quartz crystal microbalance (EQCM) technique and electrochemical impedance techniques. The type of dopant anion (PF₆⁻ vs. ClO₄⁻) used for the film preparation and the N-substituents (ethyl vs. methyl) have profound effects on the solvent transport behavior, charge capacity, and ionic resistance of the films.     

The network gel polymer electrolyte based on poly(acrylate-co-imide) and its transport properties in lithium ion batteries

Poly (acrylate-co-imide)-based gel polymer electrolytes are synthesized by in situ free radical polymerization. Infrared spectroscopy confirms the complete polymerization of gel polymer electrolytes. The ionic conductivity of gel polymer electrolytes are measured as a function of different repeating EO units of polyacrylates. An optimal ionic conductivity of the poly (PEGMEMA₁₁₀₀-BMI) gel polymer electrolyte is determined to be 4.8 × 10^–3 S/cm at 25 °C. The lithium transference number is found to be 0.29. The cyclic voltammogram shows that the wide electrochemical stability window of the gel polymer electrolyte varies from −0.5 to 4.20 V (vs. Li/Li⁺). Furthermore, we found the transport properties of novel gel polymer electrolytes are dependent on the EO design and are also related to the rate capability and the cycling ability of lithium polymer batteries. The relationship between polymer electrolyte design, lithium transport properties and battery performance are investigated in this research.     

Magnesium ion-conducting gel polymer electrolytes dispersed with fumed silica for rechargeable magnesium battery application

Effect of fumed silica dispersion on poly(vinylidene fluoride-co-hexafluoropropylene)-based magnesium ion-conducting gel polymer electrolyte has been studied using various physical and electrochemical techniques. The composite gel electrolytes are free-standing and flexible films with enough mechanical strength. The optimized composition with 3 wt.% filler offers a maximum ionic conductivity of ∼1.1 × 10⁻² S cm⁻¹ at ∼25 °C with good thermal and electrochemical stabilities. The Mg²⁺ ion conduction in the gel nanocomposite film is confirmed from the cyclic voltammetry, impedance spectroscopy, and transport number measurements. The space-charge layers formed between filler particles and gel electrolyte are responsible for the enhancement in ionic conductivity. The applicability of the gel nanocomposite to a rechargeable battery is examined by fabricating a prototype cell consisting of Mg [or Mg-multiwalled carbon nanotube (MWCNT) composite] and MoO₃ as negative and positive electrodes, respectively. The discharge capacity and the rechargeability of the cell have been improved when Mg metal is substituted by Mg-MWCNT composite. The discharge capacity of the optimized cell has found to be ∼175 mAh g⁻¹ of MoO₃ for an initial ten charge–discharge cycles.     

Electrical and Structural Properties of Poly (Methyl Methacrylate) Doped Potassium Iodide (KI) Solid Polymer Electrolyte

A high-conducting salt-doped polymer electrolyte layer has been created here for use in photocell technologies. The solution casting method is used to produce ion conducting film where poly (methyl methacrylate) (PMMA) is used as the host polymer and potassium iodide (KI) as the dopant. The conductivity and amorphic increases of the polymer electrolytes with the addition of salt concentrations helps in the enhancement of the charge transfer properties. Using electrochemical impedance spectroscopy (EIS), ionic conductivity is evaluated where maximum conductivity is 3.99 × 10⁻⁶ S cm^-1 at 20 wt% KI concentration. Polarized optical microscopy (POM) shows the reduction in crystallinity by salt doping, while Fourier transforms infrared spectroscopy (FTIR) shows the complexation as well as composite nature of the film. Ionic transference number (t_ion) measurement shows the predominantly ionic nature of this polymer electrolyte.     

Novel composite polymer electrolytes based on poly(ether-urethane) network polymer and fumed silicas

Novel composite solid polymer electrolytes (CSPEs) and composite gel polymer electrolytes (CGPEs) have been prepared. CSPE consists of poly(ether-urethane) network polymer (PUN), fumed silicas and LiClO₄. The ionic conductivity of CSPEs can be enhanced nearly 20 times in comparison with the plain system without the addition of fumed silicas and can be above 1×10⁻⁵ S/cm at room temperature. The effects of both kinds of fumed silicas, viz. uSiO₂ with hydrophilic groups at the surface and mSiO₂ with hydrophobic groups at the surface on ionic conductivity were investigated. CGPE comprising of the CSPE and LiClO₄–PC solution with good mechanical strength exhibits ionic conductivity in the order of 10⁻³ S/cm at room temperature and above 3×10⁻⁴ S/cm at low temperature −40 °C.     

Characterization and properties of ternary P(VdF-HFP)-LiTFSI-EMITFSI ionic liquid polymer electrolytes

Gel polymer electrolytes containing 1-ethyl-3-methylimidazolium-bis (trifluoromethyl-sulfnyl)imide (EMITFSI) ionic liquid were prepared for lithium ion batteries by solution casting method. Thermal and electrochemical properties have been determined for the gel polymer electrolytes. Proper addition of EMITFSI to the P(VdF-HFP)-LiTFSI polymer electrolyte improves the ionic conductivity and electrochemical window to 2.11 × 10⁻³ S cm⁻¹ (30 °C) and 4.6 V. In combination of the prepared ternary P(VdF-HFP)-LiTFSI-EMITFSI ionic liquid polymer electrolytes, Li₄Ti₅O₁₂ anode exhibited two extra voltage plateaus around 1.1 V and 2.3 V except the typical voltage plateau around 1.6 V by possible side reaction between ionic liquid and polymer. LiFePO₄ cathode exhibited high capacity above 140 mA h g⁻¹ and retention of 93.1% due to the suppressed polarization effect caused by enhanced ion transport properties. The high temperature of 80 °C didn't have significant impact on the cycling performance.     

Polyethylene-supported poly(acrylonitrile-co-methyl methacrylate)/nano-Al2O3 microporous composite polymer electrolyte for lithium ion battery

Nano-Al₂O₃ was doped in poly(acrylonitrile-co-methyl methacrylate) (P(AN-co-MMA)), and polyethylene(PE)-supported P(AN-co-MMA)/nano-Al₂O₃ microporous composite polymer electrolyte (MCPE) was prepared. The performances of the prepared MCPE for lithium ion battery use, including ionic conductivity, electrochemical stability, interfacial compatibility, and cyclic stability, were studied by scanning electron spectroscopy, linear sweep voltammetry, and electrochemical impedance spectroscopy. It is found that the nano-Al₂O₃ significantly affects the MCPE performances. Compared to the MCPE without any nano-Al₂O₃, the MCPE with 10 wt.% nano-Al₂O₃ reaches its best performances. Its ionic conductivity is improved from 2.0 × 10⁻³ to 3.2 × 10⁻³ S cm⁻¹, its decomposition potential is enhanced from 5.5 to 5.7 V (vs Li/Li⁺), and its interfacial resistance on lithium is reduced from 520 to 160 Ω cm². Thus, the battery performance is improved.     

New ladder‐type conjugated polymer containing carbazole and fluorene units in backbone: Synthesis,optical, and electrochemistry properties

This article describes the synthesis and characterization of a new ladder‐type poly (p‐phenylene) (LPFC) containing alkylcarbazole and dialkylfluorene units in backbone, and its optical and electrochemical properties as well as its light‐emitting device performance. LPFC shows the well‐defined structure, high molecular weights, excellent thermal stability, and good solubility in common organic solvents. And it also shows strongly blue emission (λ_max = 465 nm) with quantum efficiency of 70% in solution, while its solid emission (λ_max = 470 nm) is almost the same as its solution. Electrochemical studies show that the highest occupied molecular orbital (HOMO) energy levels of LPFC is up to 5.29 eV, which is significantly higher than that of LPPP without carbazole in backbone, indicating an enhanced ability of hole injection from anodes. Furthermore, the single layer light‐emitting device using LPFC as the active layer shows blue emission (λ_max = 470 nm) with maximum luminescence of ～ 2000 cd/m² and maximum luminance efficiency of 0.43 cd/A. The attractive properties exhibited from new ladder‐type polymer establish LPFC as a good candidate for the potential application as transporting and emitting layer in polymeric light emitting diodes. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 3120–3127, 2008     

Solid polymer electrolytes. IV. Preparation and characterization of novel crosslinked epoxy‐siloxane polymer complexes as polymer electrolytes

Two series of novel crosslinked siloxane‐based polymers and their complexes with lithium perchlorate (LiClO₄) were prepared and characterized by Fourier transform infrared spectroscopy, solid‐state NMR (¹³C, ²⁹Si, and ⁷Li nuclei), and differential scanning calorimetry. Their thermal stability and ionic conductivity of these complexes were also investigated by thermogravimetric and AC impedance measurements. In these polymer networks, poly(propylene oxide) chains with different molecular weights were introduced through self‐synthesized epoxy‐siloxane precursors cured with two curing agents. The glass‐transition temperature (T_g) of these copolymers is dependent on the length of the ether units. The dissolution of LiClO₄ considerably increases the T_g of the polyether segments. The dependence of the ionic conductivity was investigated as a function of temperature, LiClO₄ concentration, and the molecular weight of the polyether segments. The ion‐transport behavior was affected by the combination of the ionic mobility and number of carrier ions. The ⁷Li solid‐state NMR line shapes of these polymer complexes suggest a significant interaction between Li⁺ ions and the polymer matrix, and temperature‐ and LiClO₄ concentration‐dependent chemical shifts are correlated with ionic conductivity. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 1226–1235, 2002     

Investigation of polymer thin films by use of Bi-cluster-ion-supported time of flight secondary ion mass spectrometry

The investigation and analysis of polymer thin films with Bi _n ⁺, n = 1–7 cluster ions has been demonstrated by means of static secondary ion mass spectrometry (SIMS). The highly specific signal enhancement of these primary ions combined with the individual fragmentation pattern of poly(4-vinylphenol) and poly(methyl methacrylate) is the basic principle for a modified approach of data reduction derived from the well-established g-SIMS procedure. Based on mass spectra, which correspond to different cluster ion sizes, not only a clear distinction between the two polymers is feasible but also a further simplification of the data can be demonstrated. It has been successfully proven that characteristic polymer-relevant species can be refined out of the large amount of unspecific and highly fragmented secondary ions, which are usually present in SIMS spectra. Therefore, a more precise and direct interpretation of complex organic fragments becomes feasible, which consequently enables the investigation of even more sophisticated samples.     

Synthesis and characterization of polymer electrolytes based on cross‐linked phenoxy‐containing polyphosphazenes

A new method to prepare the polymer electrolytes for lithium‐ion batteries is proposed. The polymer electrolytes were prepared by reacting poly(phosphazene)s (MEEPP) having 2‐(2‐methoxyethoxy)ethoxy and 2‐(phenoxy)ethoxy units with 2,4,6‐tris[bis(methoxymethyl)amino]‐1,3,5‐triazine (CYMEL) as a cross‐linking agent. This method is simple and reliable for controlling the cross‐linking extent, thereby providing a straightforward way to produce a flexible polymer electrolyte membrane. The 6 mol % cross‐linked polymer electrolyte (ethylene oxide unit (EO)/Li = 24:1) exhibited a maximum ionic conductivity of 5.36 × 10^?5 S cm^?1 at 100 °C. The ⁷Li linewidths of solid‐state static NMR showed that the ionic conductivity was strongly related to polymer segment motion. Moreover, the electrochemical stability of the MEEPP polymer electrolytes increased with an increasing extent of cross‐linking, the highest oxidation voltage of which reached as high as 7.0 V. Moreover, phenoxy‐containing polyphosphazenes are very useful model polymers to study the relationship between the polymer flexibility; that is, the cross‐linking extent and the mobility of metal ions. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 352–358     

Review on gel polymer electrolytes for lithium batteries

This paper reviews the state-of-art of polymer electrolytes in view of their electrochemical and physical properties for the applications in lithium batteries. This review mainly encompasses on five polymer hosts namely poly(ethylene oxide) (PEO), poly(acrylonitrile) (PAN), poly(methyl methacrylate) (PMMA), poly(vinylidene fluoride) (PVdF) and poly(vinylidene fluoride-hexafluoro propylene) (PVdF-HFP) as electrolytes. Also the ionic conductivity, morphology, porosity and cycling behavior of PVdF-HFP membranes prepared by phase inversion technique with different non-solvents have been presented. The cycling behavior of LiMn₂O₄/polymer electrolyte (PE)/Li cells is also described.     

Electrochemical polymerization of nano-micro sheaf/wire conducting polymer poly[Ni(salen)] for electrochemical energy storage system

<正>The polymer of complex[Ni(salen)],(N,N'-ethylenebis(salicylideneaminato) nickel(H)),was prepared on graphite electrode by the route of linear sweep potential method.The nano-micro sheaf/wire structures of poly[Ni(salen)]have been obtained by adjusting the polymerization sweep rate of 5,20 and 40 mV·s~(-1).The polymer prepared at 20 mV·s~(-1) had nanoscaled wire structure of ca.100 nm in diameter.The good electrochemical reversibility of poly[Ni(salen)]was investigated by cyclic voltammetry and galvanostatic test in 1.0 mol/L Et_3MeNBF_4/acetonitrile solution.The initial specific gravimetric capacitance of poly[Ni(salen)]at the current density of 0.1 mA·cm~(-2) reached 270.2 F·g~(-1),however,the cycle stability needs to be improved.     

利用基于Gouy-Chapman模型的离子有效电荷定量表征离子特异性效应

离子特异性效应在固-液界面反应中是普遍存在的. 近期研究指出, 在较低电解质浓度的某些体系中, 离子特异性效应可能并非来源于色散力、经典诱导力、离子半径或水合半径的大小等, 而是界面附近强电场中的离子极化作用. 这种作用可使界面附近的吸附态反号离子被强烈极化(高达经典极化的10⁴倍). 强烈极化的结果将导致离子在界面附近受到的库仑力远远超过离子电荷所能产生的库仑力, 这体现在离子的有效电荷将远大于离子的实际电荷. 因此胶体体系中基于这种强极化的离子有效电荷可以用来定量表征离子特异性效应的强度. 本研究在蒙脱石-胡敏酸混合悬液凝聚过程中发现了Na⁺、K⁺、Ca²⁺、Cu²⁺四种离子的离子特异性效应, 提出了基于激光散射技术测定离子有效电荷的方法, 并成功获得了被强烈极化后的离子有效电荷数值. 实验测得的Na⁺、K⁺、Ca²⁺、Cu²⁺四种离子的有效电荷值分别为: Z_{Na(effective)}=1.46, Z_K(effective)=1.86, Z_{Ca(effective)}=3.92, Z_{Cu(effective)}=6.48.该结果表明: (1) 离子在强电场中的极化将大大提高离子的有效电荷, 从而极大地增强离子所受的库仑作用力;(2) 离子的电子层数越多, 离子极化越强烈, 离子的有效电荷增加越多.     

Effect of EMIMBF4 ionic liquid addition on the structure and ionic conductivity of LiBF4-complexed PVdF-HFP polymer electrolyte films

New polymer electrolyte films of lithium tetrafluoroborate (LiBF₄)-complexed poly(vinylidene fluoride-co-hexafluoropropylene) (PVdF-HFP) embedded with different quantities of 1-ethyl-3methylimidazolium tetrafluoroborate (EMIMBF₄) ionic liquid were prepared by solution casting. The prepared films were characterized using various techniques: X-ray diffraction, scanning electron microscopy, impedance spectroscopy and electrochemical measurements. The pure PVdF-HFP possessed a semi-crystalline structure and its amorphicity increased with the addition of LiBF₄ salt and EMIMBF₄ ionic liquid. The size and interconnection of pores in the films were enhanced by EMIMBF₄. Impedance measurements indicated that the room-temperature ionic conductivity of the films increased with increasing EMIMBF₄ concentration until 15 wt.%, being up to 0.202 × 10⁻⁴ S cm⁻¹, and then decreased with further increasing EMIMBF₄ concentration. In addition, the temperature-dependent ionic conductivity of the polymer electrolyte films followed an Arrhenius relation and the 15 wt.% EMIMBF₄-incorporated gel polymer electrolyte film exhibited a low activation energy for ionic conduction, being about 0.28 eV. Finally, the electrochemical stability window of the 85PVdF-HFP:15LiBF₄+15 EMIMBF₄ gel polymer electrolyte films was evaluated as approximately 4.4 V, which is a promising value for ion battery applications.     

A novel PEO-based composite solid-state polymer electrolyte with methyl group-functionalized SBA-15 filler for rechargeable lithium batteries

Functionalized molecular sieve SBA-15 with trimethylchlorosilane was used as an inorganic filler in a poly(ethyleneoxide) (PEO) polymer matrix to synthesize a composite solid-state polymer electrolyte (CSPE) using LiClO₄ as the doping salts, which is designated to be used for rechargeable lithium batteries. The methyl group-functionalized SBA-15 (^fSBA-15) powder possesses more hydrophobic characters than SBA-15, which improves the miscibility between the ^fSBA-15 filler and the PEO matrix. The interaction between the ^fSBA-15 and PEO polymer matrix was investigated by scanning electron microscopy, X-ray diffraction, and differential scanning calorimetry. Linear sweep voltammetry and electrochemical impedance spectroscopy were employed to study the electrochemical stability windows, ionic conductivity, and interfacial stability of the CSPE. The temperature dependence of the change of the PEO polymer matrix in the CSPE from crystallization to amorphous phase was surveyed, for the first time, at different temperature by Fourier transform infrared emission spectroscopy. It has demonstrated that the addition of the ^fSBA-15 filler has improved significantly the electrochemical compatibility of the CSPE with a lithium metal electrode and enhanced effectively the ion conductivity of the CSPE. Dedicated to Professor Oleg Petrii on the occasion of his 70th birthday on August 24th, 2007.