Cu/MoO3-TiO2光催化CO2与C3H6反应合成甲基丙烯酸的性能

 研究了Cu/MoO3-TiO2上CO2和C3H6的吸附特性及其光催化CO2与C3H6反应合成甲基丙烯酸(MAA)的性能. 结果表明,在Cu/MoO3-TiO2催化剂表面存在金属Cu位、Lewis酸位Mo6+和Ti4+以及Lewis碱位Mo-O-Ti的桥氧和Mo=O的端氧三类活性中心. 在金属Cu位和Lewis酸位Ti4+(Mo6+)的协同作用下,CO2形成活性较高的卧式吸附态Cu-(CO)-O→Ti4+(Mo6+),C3H6的β-H和β-C分别吸附在Lewis碱位 Mo=O 与金属Cu位上形成Cu-C(CH2)(CH3)-H→O=Mo吸附态. Cu/MoO3-TiO2催化剂吸收阈值蓝移和光吸收量的提高均有利于其催化活性的提高,Cu/10%MoO3-TiO2 光催化剂的催化活性优于其它MoO3含量的催化剂,光量子产率达22.8%,在110 ℃,0.1 MPa,空速200 h-1和125 W紫外灯辐照下,C3H6转化率为8.4%,MAA选择性超过95%. 提出了催化剂光促表面催化CO2与C3H6合成MAA的反应机理.     

CO2和CH3OH直接合成碳酸二甲酯Cu-Ni/V2O5-SiO2催化剂

采用表面反应改性法制备了V2O5 SiO2(VSiO)表面复合物 ,用等体积浸渍法制备了VSiO担载的Cu Ni双金属催化剂 ,用IR、TPD、TPSR和微反技术研究了CO2 和CH3OH在催化剂表面上的化学吸附与反应性能.结果表明,在Cu Ni/VSiO催化剂上存在着金属位Cu Ni合金、Lewis酸位Vn 和Lewis碱位V=O三类活性中心 ;CO2 在金属位和Lewis酸位协同作用下可生成CO2卧式吸附态M -(CO) -O→Vn ,此吸附态在138℃左右可解离成M -CO和V=O ;CH3OH在Lewis酸位和Lewis碱位协同作用下可形成解离吸附态V -OCH3和V -OH ;CO2 和CH3OH在Cu Ni/VSiO催化剂表面上的反应产物主要为碳酸二甲酯(DMC)、CH2O、CO和H2O ,其生成DMC的选择性在85%以上.     

CO2和CH3OH直接合成碳酸二甲酯用Cu-Ni/ZrO2-SiO2催化剂

 采用表面反应改性法制备了ZrO2－SiO2（ZrSiO）表面复合物,用等体积浸渍法制备了ZrSiO担载的Cu－Ni双金属催化剂,并用IR,TPD,TPSR和微反技术考察了CO2和CH3OH在催化剂表面上的化学吸附及反应性能．实验结果表明：在Cu－Ni／ZrSiO催化剂上存在着Cu－Ni金属位M,Lewis酸位Zrn＋和Lewis碱位Zr－O－三类活性中心;CO2在金属位和Lewis酸位的协同作用下可形成CO2卧式吸附态,此吸附态在142℃左右可解离成M－CO和Zr－O－;CH3OH在Lewis酸位和Lewis碱位的协同作用下可形成解离吸附态Zr－OCH3和Zr－OH;CO2和CH3OH在Cu－Ni／ZrSiO催化剂表面上的主要反应产物为碳酸二甲酯（选择性在85％以上）,另有少量的CH2O,CO和H2O．     

CH4部分氧化制氢Ni-Cu/ZrSiO催化剂的研究

采用表面反应改性法制备了ZrO2-SiO2(ZrSiO)表面复合物，用等体积浸渍法制备了ZrSiO负载的Ni-Cu双金属催化剂，并用IR、TPD、TPSR和微反技术考察了CH4、H2O和O2在催化剂表面上的化学吸附及反应性能。结果表明，在Ni-Cu /ZrSiO催化剂上存在着Ni-Cu金属位，Lewis酸位Znn+和碱位Zr-O－三类活性中心；CH4和H2O在金属位和Lewis酸位Znn+和碱位Zr-O－的协同作用下可形成解离吸附态； CH4、H2O和O2在Ni-Cu /ZrSiO催化剂表面上的主要反应产物为H2和CO2，选择性均在95％以上。     

V2O5/SiO2催化剂的异丁烷选择氧化反应性能

 采用溶胶－凝胶法和浸渍法制备了V2O5／SiO2催化剂,并用XRD,IR,TPD和活性评价等手段对催化剂的表面构造、化学吸附性能和异丁烷选择氧化反应性能进行了研究．结果表明：催化剂表面由Lewis碱位V＝O双键的端氧和Lewis酸位V5＋构成,异丁烷分子主要通过甲基中的H双位吸附在催化剂表面的Lewis碱位上,异丁烯分子可通过甲基的H吸附在催化剂表面的Lewis碱位,也可通过C＝C双键吸附在催化剂表面的Lewis酸位上．在常压条件下,异丁烷选择氧化产物主要有异丁烯、甲基丙烯醛和甲基丙烯酸,其中深度氧化产物CO2主要由通过C＝C吸附的异丁烯继续反应生成．     

K2O助剂对合成碳酸二甲酯用Cu/Ni/ZrO2-SiO2催化剂的吸附和催化性能的影响

 用等体积浸渍法制备了ZrO2－SiO2（ZrSiO）表面复合氧化物负载的Cu－Ni催化剂,并用IR,TPR,TPD及微反技术考察了K2O助剂对CO2和CH3OH在Cu－Ni／ZrSiO催化剂表面上的吸附及合成碳酸二甲酯（DMC）反应性能的影响．结果表明：加入K2O助剂使CO2在催化剂表面上的吸附增强,当n（K）／n（Cu＋Ni）＝15％时,CO2在催化剂表面上吸附后生成K2CO3;CH3OH在催化剂表面上的解离吸附态（CH3O－和H＋）的吸附减弱;CO2和CH3OH在Cu－Ni／ZrSiO催化剂表面上反应的主要产物为DMC,H2O,CO和CH2O;随着K2O助剂的加入,反应转化率及DMC选择性提高,副产物（CO和CH2O）的选择性下降．根据实验结果,探讨了K2O对催化剂表面活性中心电荷分布的影响．     

Cu/WO3-TiO2光催化剂上丙烯和二氧化碳合成MAA反应性能

研究了Cu/WO₃-TiO₂对CO₂和C₃H₆的吸附特性和光催化性能.结果表明,在Cu/WO₃-TiO₂催化剂表面存在金属位Cu,Lewis酸位W⁶⁺和Ti⁴⁺以及Lewis碱位W-O-Ti的桥氧和WO的端氧三类活性中心;在金属位Cu和Lewis酸位Ti⁴⁺(或W⁶⁺)的协同作用下,CO₂形成活性较高的卧式吸附态Cu-(CO)-O→Ti⁴⁺(或W⁶⁺),C₃H₆的β-H和β-C分别吸附在Lewis碱位WO与金属位Cu上,形成Cu-(CH₂)C(CH₃)-H→OW吸附态;Cu/WO₃-TiO₂催化剂吸收阈值蓝移和光吸收量的提高均有利于其催化活性的提高,担载质量分数为10%的WO₃光催化剂的催化活性优于其它含量的催化剂,光量子效率最高(19.7%);在383K,0.1MPa,空速200h^-1和125W紫外灯辐照下,C₃H₆转化率为7.4%,甲基丙烯酸(MAA)的选择性超过95%.根据实验结果提出了光促表面催化合成反应的机理.     

二氧化碳与丙烯直接合成甲基丙烯酸用CuPMo／TiO2催化剂的研究

 用溶胶－凝胶法以磷钼酸（MPA）的铜盐溶液水解钛酸四丁酯制备了CuPMo／TiO2催化剂，并用ICP，XRD，TG－DTA，IR，TPD－MS和微反技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化性能．结果表明：杂多钼酸盐与TiO2表面通过O2－桥发生键联．在623K下，杂多阴离子仍保持其原有的Keggin结构；CO2在Lewis酸位Cu（Ⅱ）和Lewis碱位Cu－O－Mo桥氧的协同作用下形成卧式吸附态Cu（Ⅱ）←O－（CO）←（O－－Cu）；丙烯以分子吸附态在催化剂上吸附；在空速1500h－1，压力1MPa和温度563K的反应条件下，丙烯的转化率为4．2％，甲基丙烯酸的选择性为96％．     

K_2O助剂对合成碳酸二甲酯用Cu-Ni/MoO_3-SiO_2催化剂吸附和反应性能的影响

用等体积浸渍法制备了MoO3 SiO2 (MoSiO)表面复合氧化物负载的Cu Ni K2 O催化剂。利用IR ,TPR ,TPD以及微反技术研究了K2 O助剂对CO2 和CH3OH在Cu Ni MoSiO催化剂表面上吸附和合成DMC(碳酸二甲酯 )反应性能的影响。结果表明 :K2 O助剂的加入 ,使CO2 在催化剂表面吸附强度增加 ,当K2 O含量达Cu Ni总量的 15 %时 ,CO2 在催化剂表面上吸附后生成K2 CO3;CH3OH在催化剂表面上的解离吸附态 (CH3O- H )的吸附强度减弱 ;CO2 和CH3OH在Cu Ni K2 O MoSiO催化剂表面反应主要产物为DMC ,H2 O ,CO和CH2 O。随着K2 O助剂的加入 ,反应转化率在 10 %之前增加 ,之后下降 ,DMC选择性稍有提高。副产物 (CO和CH2 O)的选择性下降。根据实验结果探讨了K2 O对催化剂表面活性中心的电荷分布的影响。     

SnO2—SiO2负载Cu,Ni催化剂的CO2加氢反应性能

采用表面反应改性法制备了SnO2-SiO2(SnSIO)表面复合物载体,用等体积浸渍法制备了SnSiO担载的Cu-Ni双金属催化剂,借助BFT,XRD,TPR,IR和微反等技术研究了SnSiO及其负载的Ni,Cu双金属催化剂的表面构造,化学吸附及CO2加氢反应性能,结果表明：SnSiO是SnO2单分子层价联于SiO2表面的复合氧化物,仍保持类似SiO2载体的孔结构和比表面;SnO2引入SiO2表面后可以有效地促进CuO,NiO的还原,还原后成为负载在SnSiO载体表面的Cu-Ni合金,CO2在负载型Cu-Ni合金表面Cu或表面Ni位 发生化学吸附,形成线式和剪式吸附;CO2在催化剂上的加氢反应产物主要是CH3OH,CH4,CO和H2O,生成CH3OH的选择性与催化剂组成及反应条件密切相关,Cu-Ni催化剂,在0．5MPa,170度,H2。CO2（mol/mol)为3 的条件下,CH3OH的选择性达到84．6％。     

Syntheses of 2-hydroperoxy-and 2-hydroxy-2H-imidazoles

Oxidation of fully substituted imidazoles 1 by singlet oxygen gives in good yield fully substituted 2-hydroperoxy-2H-imidazoles 2 . Reduction of 2 by triphenylphosphine leads to 2-hydroxy-2H-irnidazoles 3 . Limitations of the methods are reported.     

Crystal Structures of [Bu2Sn(O2PPh2)2], [Ph2Sn(O2PPh2)2], and [PhClSn(O2PPh2)OMe]2. Raman Spectra of [Ph2Sn(O2PPh2)2] and [PhClSn(O2PPh2)OMe]2

[(n‐Bu)₂Sn(O₂PPh₂)₂] ( 1 ), and [Ph₂Sn(O₂PPh₂)₂] ( 2 ) have been synthesized by the reactions of R₂SnCl₂ (R=n‐Bu, Ph) with HO₂PPh₂ in Methanol. From the reaction of Ph₂SnCl₂ with diphenylphosphinic acid a third product [PhClSn(O₂PPh₂)OMe]₂ ( 3 ) could be isolated. X‐ray diffraction studies show 1 to crystallize in the monoclinic space group P2₁/c with a = 1303.7(1) pm, b = 2286.9(2) pm, c = 1063.1(1) pm, β = 94.383(6)°, and Z = 4. 2 crystallizes triclinic in the space group , the cell parameters being a = 1293.2(2) pm, b = 1478.5(4) pm, c = 1507.2(3) pm, α = 98.86(3)°, β = 109.63(2)°, γ = 114.88(2)°, and Z = 2. Both compounds form arrays of eight‐membered rings (SnOPO)₂ linked at the tin atoms to form chains of infinite length. The dimer 3 consists of a like ring, in which the tin atoms are bridged by methoxo groups. It crystallizes triclinic in space group with a = 946.4(1) pm, b = 963.7(1) pm, c = 1174.2(1) pm, α = 82.495(6)°, β = 66.451(6)°, γ = 74.922(6)°, and Z = 1 for the dimer. The Raman spectra of 2 and 3 are given and discussed.     

Electrochemical study of (NEt4)2Cl2FeS2MoS2 and (NEt4)2Cl2FeS2MoS2FeCl2

Summary The ability of [MoS₄]^2–, anions to be used as ligands for transition metal ions has been widely demonstrated, especially with Fe²⁺. The present study has been restricted to linear complexes such as (NEt₄)₂ [Cl₂FeS₂MoS₂] and (NEt₄)₂[Cl₂FeS₂MoS₂FeCl₂]. Their electrochemical properties are described: upon electrochemical reduction, these compounds yield MoS₂, as a black precipitate, and an iron complex in solution, assumed to be [SFeCl₂]^2–. The electrochemical reduction goes through two electron transfers, coupled with the breakdown of the molecular skeleton: a DISPl and an ECE mechanism. Depending on the solvent, the following equilibrium may be observed: [Cl₄Fe₂MoS₄]^2–[Cl₂FeMoS₄]^2–+FeCl₂. The equilibrium constant, K_D, was evaluated by differential pulse polarography. K_D is tightly related to the donor number of the solvent.     

Photocycloaddition of 2-Cyanocycloalk-2-Enones to 2, 3-Dimethylbut-2-Ene

Irradiation of 5,5-dimethyl-6-oxocyclohex- l-ene- l-carbonitrile ( 1 ) in the presence of 2,3-dimethylbut-2-ene afforded 3,3,4,4,7,7-hexamethyl-3,4,4a,5,6,7-hexahydroindeno[1,7-c,d]-],2-oxazole (3) in nearly quantitative yield. In contrast, 4,4-dimethyl-5-oxo-cyclopent-l-ene-l-carbonitrile ( 2 ) under the same conditions reacted not to a tricyclic isoxazole but to a 2:1 mixture of 3,3,6,6,7,7-hexamethyl-2-oxo-bicyclo[3.2.0]heptane-l-carbonitrile ( 4 ) and trans-3,3-dimethyl-2-oxo-5-(2,3-dimethylbut-3-en-2-yl)cyclopentane-l-carbonitrile ( 5 ), respectively.     

Thermal decomposition of Me3SnO2PCl2, Me2Sn(O2PCl2)2 and Ph3SnO2PCl2

TG and DTA studies on Me₃SnO₂PCl₂, Me₂Sn(O₂PCl₂)₂ and Ph₃SnO₂PCl₂ were carried out under dynamic argon atmosphere. The results show that the decomposition proceeds in different stages leading to the formation of Sn₃(PO₄)₂ as a stable product. This compound was characterized by IR spectroscopy. Decomposition schemes involving reductive elimination reactions were proposed.     

Efficient C2 functionalisation of 2H-2-imidazolines

Alkylation and oxidation of 2H-2-imidazolines, followed by regioselective deprotection, thionation and microwave-assisted Liebeskind-Srogl reaction, efficiently led to 2-aryl-2-imidazolines as new analogues of p53-hdm2 interaction inhibitors (Nutlins).