ZIF-8/改性聚丙烯腈电纺纳米纤维的制备及其高效去除水中孔雀石绿

通过原位生长方法,将最常见的金属有机骨架(MOFs)——沸石咪唑酯骨架材料(ZIF-8)固定到羧甲基化聚丙烯腈静电纺丝纳米纤维(PAN-COOH NFs)表面,得到ZIF-8/PAN-COOH NFs。通过扫描电子显微镜(SEM)、能量色散光谱(EDS)、X射线粉末衍射(XRD)和傅里叶变换红外光谱(FTIR)对合成的ZIF-8/PAN-COOH NFs形貌和结构进行表征,并深入研究ZIF-8/PAN-COOHNFs从废水中去除孔雀石绿(MG)的性能。研究发现： ZIF-8/PAN-COOH NFs对MG的吸附符合拟二级动力学方程,吸附过程可采用Langmuir等温线模型拟合,其对MG的最大吸附容量可达3 604 mg·g^-1。此外,ZIF-8/PAN-COOH NFs在染料吸附实验中表现出良好的分离功能和重复利用性。     

ZIF-8/改性聚丙烯腈电纺纳米纤维的制备及其高效去除水中孔雀石绿

通过原位生长方法,将最常见的金属有机骨架（MOFs）——沸石咪唑酯骨架材料（ZIF‐8）固定到羧甲基化聚丙烯腈静电纺丝纳米纤维（PAN‐COOH NFs）表面,得到ZIF‐8/PAN‐COOH NFs。通过扫描电子显微镜（SEM）、能量色散光谱（EDS）、X射线粉末衍射（XRD）和傅里叶变换红外光谱（FTIR）对合成的ZIF‐8/PAN‐COOH NFs形貌和结构进行表征,并深入研究ZIF‐8/PAN‐COOHNFs从废水中去除孔雀石绿（MG）的性能。研究发现： ZIF‐8/PAN‐COOH NFs对MG的吸附符合拟二级动力学方程,吸附过程可采用Langmuir等温线模型拟合,其对MG的最大吸附容量可达3 604 mg·g^-1。此外,ZIF‐8/PAN‐COOH NFs在染料吸附实验中表现出良好的分离功能和重复利用性。     

Water-soluble Fe3O4 nanoparticles with high solubility for removal of heavy-metal ions from waste water

In this contribution, we synthesized water-soluble Fe(3)O(4) nanoparticles (NPs) with sufficiently high solubility (28 mg mL(-1)) and stability (at least one month) through a hydrothermal approach, and found that they exhibited excellent removal ability for heavy-metal ions from waste water. For the first time, the water-soluble Fe(3)O(4) NPs were used as adsorbents for heavy-metals removal from wastewater. It is noteworthy that the adsorption ability of the water-soluble Fe(3)O(4) NPs for Pb(2+) and Cr(6+) is stronger than water-insoluble Fe(3)O(4) NPs. Furthermore, the water-soluble Fe(3)O(4) NPs exhibited relatively high saturation magnetization (83.4 emu g(-1)), which allowed their highly-efficient magnetic separation from wastewater. The most important thing is that the water-soluble magnetite as an adsorbent can directly dissolve in water without the help of mechanical stirring or any extraneous forces, which may solve a key problem for the practical application of magnetic powders in the field of sewage purification. Moreover, the water-soluble Fe(3)O(4) NPs show a highly-efficient adsorption capacity for 10 ppm of Pb(2+) ions solution which can reach 90% within 2 minutes.     

Phosphorylated polyacrylonitrile‐based electrospun nanofibers for removal of heavy metal ions from aqueous solution

The phosphorylated polyacrylonitrile‐based (P‐PAN) nanofibers were prepared by electrospinning technique and used for removal of Cu²⁺, Ni²⁺, Cd²⁺, and Ag⁺ from aqueous solution. The morphological and structural properties of P‐PAN nanofibers were characterized by scanning electron microscope and Fourie transform infrared spectra. The P‐PAN nanofibers were evaluated for the adsorption capacity at various pH, contact time, and reaction temperature in a batch system. The reusability of P‐PAN nanofibers for the removal of heavy metal ions was also determined. Adsorption isotherms and adsorption kinetics were also used to examine the fundamental adsorption properties. It is found that the P‐PAN nanofibers show high efficiency, and the maximal adsorption capacities of metal ions as calculated from the Langmuir model were 92.1, 68.3, 14.8, and 51.7 mg/g, respectively. The kinetics of the heavy metal ions adsorption were found to follow pseudo‐second‐order rate equation, suggesting chemical adsorption can be regarded as the major factor in the adsorption process. Sorption/desorption results reveal that the obtained P‐PAN nanofibers can remain high removal efficiency after four cycles.     

Functionalized electrospun carbon nanofibers for removal of cationic dye

Electrospun carbon nanofibers (ECNFs) have attracted significant attention in recent years as relatively inexpensive alternative to carbon nanotubes for adsorption organic pollutants. In this study, ECNFs were fabricated from polyacrylonitrile (PAN) using an electrospinning technique, followed by carbonization and oxidation via treatment with a H₂SO₄/HNO₃ mixture. The prepared oxidized electrospun carbon nanofibers (O-ECNFs) were characterized using scanning and transmission electron microscopy (SEM and TEM), Fourier transform infrared (FT-IR), Brunauer-Emmett-Teller (BET), X-ray diffraction (XRD), and thermogravimetric analysis (TGA). The O-ECNFs were used as nano-adsorbents for the adsorption of methylene blue (MB) from aqueous solution. The adsorption of MB by the O-ECNFs was studied as a function of pH, time, adsorbent dosage, MB concentration, and temperature. ECNF functionalization enhanced the adsorption capacity towards MB dye compared pristine ECNFs. Detailed analysis of the adsorption kinetics showed that the adsorption process followed a pseudo-second-order model. The adsorption isotherm was best fit by the Langmuir model. The thermodynamic results showed that MB adsorption onto the O-ECNFs was endothermic and spontaneous.     

Preparation of amidoxime-modified polyacrylonitrile (PAN-oxime) nanofibers and their applications to metal ions adsorption

Polyacrylonitrile (PAN) nanofibers were applied to metal adsorption. PAN nanofibers (prepared by an electrospinning technique) were chemically modified with amidoxime groups, which are suitable for metal adsorption due to their high adsorption affinity for metal ions. The adsorption of the amidoxime-modified PAN (PAN-oxime) (25% conversion) nanofibers followed Langmuir isotherm. The saturation adsorption capacities for Cu(II) and Pb(II) of 52.70 and 263.45 mg/g (0.83 and 1.27 mmol/g), respectively, indicating that the monolayer adsorption occurred on the nanofiber mats. In addition, over 90% of metals were recovered from the metal-loaded PAN-oxime nanofibers in a 1 mol/L HNO₃ solution after 1 h.     

Process optimization and empirical modeling for electrospun polyacrylonitrile (PAN) nanofiber precursor of carbon nanofibers

Ultrafine fibers were spun from polyacrylonitrile (PAN)/N,N-dimethyl formamide (DMF) solution as a precursor of carbon nanofibers using a homemade electrospinning set-up. Fibers with diameter ranging from 200 nm to 1200 nm were obtained. Morphology of fibers and distribution of fiber diameter were investigated varying concentration and applied voltage by scanning electric microscopy (SEM). Average fiber diameter and distribution were determined from 100 measurements of the random fibers with an image analyzer (SemAfore 5.0, JEOL). A more systematic understanding of process parameters was obtained and a quantitative relationship between electrospinning parameters and average fiber diameter was established by response surface methodology (RSM). It was concluded that concentration of solution played an important role to the diameter of fibers and standard deviation of fiber diameter. Applied voltage had no significant impact on fiber diameter and standard deviation of fiber diameter.     

Enhancing adsorption of heavy metal ions onto biobased nanofibers from waste pulp residues for application in wastewater treatment

Biobased nanofibers are increasingly considered in purification technologies due to their high mechanical properties, high specific surface area, versatile surface chemistry and natural abundance. In this work, cellulose and chitin nanofibers functionalized with carboxylate entities have been prepared from pulp residue (i.e., a waste product from the pulp and paper production) and crab shells, respectively, by chemically modifying the initial raw materials with the 2,2,6,6-tetramethyl-1-piperidinyloxy (TEMPO) mediated oxidation reaction followed by mechanical disintegration. A thorough investigation has first been carried out in order to evaluate the copper(II) adsorption capacity of the oxidized nanofibers. UV spectrophotometry, X-ray photoelectron spectroscopy and wavelength dispersive X-rays analysis have been employed as characterization tools for this purpose. Pristine nanofibers presented a relatively low content of negative charges on their surface thus adsorbing a low amount of copper(II). The copper adsorption capacity of the nanofibers was enhanced due to the oxidation treatment since the carboxylate groups introduced on the nanofibers surface constituted negative sites for electrostatic attraction of copper ions (Cu²⁺). The increase in copper adsorption on the nanofibers correlated both with the pH and carboxylate content and reached maximum values of 135 and 55 mg g^?1 for highly oxidized cellulose and chitin nanofibers, respectively. Furthermore, the metal ions could be easily removed from the contaminated nanofibers through a washing procedure in acidic water. Finally, the adsorption capacity of oxidized cellulose nanofibers for other metal ions, such as nickel(II), chromium(III) and zinc(II), was also demonstrated. We conclude that TEMPO oxidized biobased nanofibers from waste resources represent an inexpensive and efficient alternative to classical sorbents for heavy metal ions removal from contaminated water.     

In situ synthesis of gold nanoparticles on porous polyacrylonitrile nanofibers for sensing applications

A simple and cost-effective method was reported to synthesize small size (6 nm) gold nanoparticles (AuNPs) on polyacrylonitrile (PAN) electrospun nanofibers (AuNPs/PAN). The formation of AuNPs is attributed to the in situ reduction of Au(III) to Au(0) by 4-(dimethylamino)benzaldehyde doped in the PAN nanofibers. Electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV) confirmed that the AuNPs/PAN nanofibers showed good conductivity. The AuNPs/PAN nanofibers were used to immobilize tris(2,2'-bipyridyl)ruthenium(II) ions (Ru(bpy)(3)(2+)) to form an electrochemiluminescence (ECL) sensor. The AuNPs on the PAN nanofibers exhibited an excellent catalytic effect on the ECL of Ru(bpy)(3)(2+) which could be employed to detect low concentrations of phenolic compounds. The linear response range of the ECL sensor to hydroquinone is 0.55-37 μM with limit of detection of 80 nM (S/N = 3). This sensor has been successfully applied to determine the hydroquinone content in photographic developer samples. Our work provides a very simple and cost-effective method to synthesize AuNPs on polymer nanofibers which shows great potential in the field of electrocatalysis and chemo/biosensors.     

Carrier mediated extraction: application of double emulsion technique for mercury removal from waste water

Extraction of mercury(II) cations from low-pH aqueous solutions by means of a double emulsion technique was studied in a laboratory scale, 2 l turbine agitator. A 10% solution of long-chain fatty acids (oleic and linolic) in normal paraffins (C₁₁C₁₅) was used as the intermediate phase. The optimal operational conditions for fast and complete removal of mercury, providing a 1000 fold concentration increase of the metal in the receiving, encapsulated phase, were obtained.     

Polymer-free electrospun separator film comprising silica nanofibers and alumina nanoparticles for Li-ion full cell

A separator film for high-performance Li-ion batteries was prepared by electrospinning. The film had a hybrid morphology of silica nanofibers(SNFs) and alumina nanoparticles(ANPs), with a smooth surface, polymer-free composition, high porosity(79%), high electrolyte uptake(876%), and excellent thermal stability. Contact angle measurements demonstrated the better immersion capability of the SNF-ANP separator film for commercial liquid electrolytes than a commercial CELGARD 2500 separator film. Moreover,compared to the commercial CELGARD 2500 separator, the ionic conductivity of the SNF-ANP separator film was nearly three times higher, the bulk resistance was lower at elevated temperature(120 ℃), the interfacial resistance with lithium metal was lower, and the electrochemical window was wider. Full cells were fabricated to determine the cell performance at room temperature. The specific capacity of the full cell with the SNF-ANP separator film was 165 mAh g~(-1); the cell was stable for 100 charge/discharge cycles and exhibited a capacity retention of 99.9%. Notably, the electrospun SNF-ANP separator film can be safely used in Li-ion or Li-S rechargeable batteries.     

Carbon nanofibers with nanoporosity and hollow channels from binary polyacrylonitrile systems

Carbon nanofibers with new structural features, e.g. nanoporosity, hollow, U-shape cross-section, were generated by utilizing the phase separation behavior of polymer additive with polyacrylonitrile (PAN). The approach involved the formation of precursor fibers by electrospinning of binary mixtures of PAN with poly(ethylene oxide) (PEO), cellulose acetate (CA) or poly(methyl methacrylate) (PMMA), the removal of the polymer and the carbonization of the remaining PAN. The carbon nanofiber yield was ca 50% of PAN in all cases. Nanoporous carbon nanofibers with an average diameter of 100 nm were generated from the water treated PAN/PEO precursors. Multi-channel hollow fibers (90-190 nm diameters) were produced from the acetone treated PAN/CA precursors. Carbon fibers produced from the chloroform treated PAN/PMMA precursors were 250-400 nm in diameters and consisted of varied hollow structures, i.e., hollow and U-shape cross-sections from those containing 30% and 50% PAN, respectively, and multi-channel hollow fibers from the 70/30 PAN/PMMA precursor. Carbonization of equal-mass PAN/PMMA as-spun fibers also produced similarly U-shape cross-sections as the chloroform treated ones, showing promise of direct carbonization. This simple and yet versatile approach to create new structural features in carbonized fibers has shown to depend on the distinct phase separation as well as the pyrolytic behaviors of the second polymer component.     

One-pot surfactantless route to polyaniline hollow nanospheres with incontinuous multicavities and application for the removal of lead ions from water

Polyaniline (PANI) hollow nanospheres with controllable incontinuous nanocavities ranging in size from 10 to 50 nm as a novel hollow nanostructure have been successfully fabricated by chemical polymerization of aniline with chloroaurate acid as the oxidant and citric acid as the doping acid. Experimental factors, such as concentration and kind of oxidant and doping acid, were investigated to illustrate their effect on morphology of PANI. According to experimental results and time-dependent investigations, a possible formation mechanism involved was then proposed. The adaptability of this route to hollow nanostructures with multicavities of other conducting polymer was also revealed. Furthermore, the adsorption properties of PANI hollow nanospheres toward lead ions in water were investigated.     

Cellulosic-based hydrogel from biomass material for removal of metals from waste water

Abstract

Cellulose and carboxymethyl cellulose (CMC), prepared from rice straw, were used for hydrogel preparation, separately or in a mixture of both of them in a ratios of 1:1, 1:4, 1:9, 2:3 and 3:7 (by weight).They were polymerized with partially neutralized acrylic acid (AA) in the presence of potassium persulphate, as initiator, and vinylsulphone (VS), as cross-linker. Moreover, glutaraldehyde, N,N-methylene bis acrylamide (MBA) and Epichlorohydrin (ECH) were used as cross-linker for the mixture of 1:1 of Cellulose: CMC. The mechanism of the polymerization was studied and the resulted hydrogels were characterized for their appearances, yields percentage, and water absorbencies. The Fourier transform infrared spectroscopy (FT-IR) and XRD analysis were also investigated for the hydrogel samples. Since the textile industry produces large volumes of wastewaters which contain hazardous compounds such as dyes, heavy metals like Cu(II), and surfactants, so we aimed in this research to use the hydrogel samples for Cu²⁺ absorption that can be presented in the wastewater. The FT-IR spectrum, before and after absorption, indicated that the prepared hydrogels were able to absorb the Cu²⁺. The Cu²⁺ ions can be recovered and dried to be reused again as well as the hydrogel samples can be available again for reuse.     

Resorbable polymer electrospun nanofibers: History,shapes and application for tissue engineering

Resorbable polymer electrospun nanofiber-based materials/devices have high surface-to-volume ratio and often have a porous structure with excellent pore interconnectivity,which are suitable for growth and development of different types of cells.Due to the huge advantages of both resorbable polymers and electrospun nano fibers,re sorbable polymer electrospun nanofibers(RPENs)have been widely applied in the field of tissue engineering.In this paper,we will mainly introduce RPENs for tissue engineering.Firstly,the electrospinning technique and electrospun nanofiber architectures are briefly introduced.Secondly,the application of RPENs in the field of tissue engineering is mainly reviewed.Finally,the advantages and disadvantages of RPENs for tissue engineering are discussed.This review will provide a comprehensive guide to apply resorbable polymer electrospun nanofibers for tissue engineering.     

Synthesis and properties of thermoresponsive magnetic polymer composites and their electrospun nanofibers

The thermoresponsive magnetic polymer composites and nanofibers were fabricated. Their thermal and magnetic properties were also investigated. Fe₃O₄ nanoparticles were prepared by coprecipitation method. Further condensation reaction was used to fabricate the double‐layer lauric acid modified Fe₃O₄ (DLF) nanoparticles dispersed well in water. Thermal properties of poly(N‐isopropylacrylamide) (PNIPAAm) and DLF/PNIPAAm composites and their aqueous solutions were measured by TGA and DSC. With the increasing of DLF content, the interaction between DLF and PNIPAAm caused the lower critical solution temperature (LCST) of polymer solution to shift from 33 to 31.25 °C. The effects of concentration and pH on LCST were also studied. The DLF/PNIPAAm nanofibers were fabricated by electrospinning. Their diameters were around 100–250 nm. Magnetization curves of DLF/PNIPAAm composite and nanofibers were overlapped and the saturated magnetizations were the same. Magnetic attraction behaviors of DLF/PNIPAAm polymer solution at temperatures below and above LCST were different. Aggregation of DLF/PNIPAAm above LCST enhanced magnetic moment density as well as magnetic attraction ability. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 848–856     

Mineral sorbents for the removal of oil products from waste water

Properties of filtering-sorption materials based on basalt fibers and bentonite clays intended for the removal of oil products from water were studied. Optimal parameters of a feed providing the maximal purification efficiency with the minimal power consumption were determined.     

Synthesis of calcium alginate nanoparticles for removal of lead ions from aqueous solutions

Calcium alginate nanoparticles (CANPs) were synthesized to remove lead ion [Pb(??)] as pollutant of environment from aqueous solutions. The produced CANPs were characterized by Fourier transform infrared spectroscopy (FTIR), particle size analysis (PSA) and scanning electron microscope (SEM). Various factors, which affected adsorption efficiency of lead ions by CANPs, such as pH (pH from 1 to 8), initial ions concentration (in the range of 25 to 125 mg L^–1), contact time (varying from 5 to 120 min), and adsorbent dose (50 to 500 mg L^–1), were investigated for determination of optimum experimental conditions. The result of tests showed that the investigated factors had significant effects on adsorption of Pb(??) ions and the maximum adsorption percentage of lead at pH = 6~7, 25 mg L^–1 initial ions concentration, contact time of more than 140 min. and for adsorbent dose at 500 mg L^–1. Also these results demonstrated the effective adsorption of Pb²⁺ ions by synthesized CANPs that occurred due to a high surface area of CANPs and the presence of anionic carboxylate functional groups and allowed effective absorbing and removing Pb(??) ions from aqueous solutions. Thus, these nanoparticles were able to remove over 99% of lead ions from solution.     

Starch-modified filters used for the removal of dyes from waste water

The present article proposes the use of starch-enriched flour as low-cost adsorbent of dyes. The adsorbents have been prepared by reticulation of starch-enriched flour using epichlorohydrin as crosslinking agent. These starch-modified filters exhibit interesting properties in terms of sorption rate. Studies concerning the sorption capacity are presented. The influence of the amine groups and the chemical structure of dyes are also studied. The regeneration procedure of the filters is showed and discussed. In order to explain the results, an adsorption mechanism mainly based on physical adsorption and interactions such as hydrogen bonds and ion-exchange due to the nature of the polymer network is proposed.