Amperometric measurements with ion-selective electrode membranes in a flow system

Calcium and salicylate sensitive electrode membranes based on plasticized PVC were used for selective amperometric detection in a flow injection system. The peak current was found to depend linearly on concentration and the working range extended well below the potentiometric detection limit.Dedicated to Professor W. Simon on the occasion of his 60th birthday     

Spectrophotometric determination of chloride in waters using a multisyringe flow injection system

A multisyringe flow injection system (MSFIA) with spectrophotometric detection is proposed as a fast, robust and low-reagent consumption system for the determination of chloride (Cl⁻) in waters. The system is based in the classic reaction of Cl⁻ with Fe³⁺ and Hg(SCN)₂, but due to the hazardous properties of this last reagent, the proposed methodology has been developed with the aim to minimize the consumption of this one, consuming less than 0.05 mg of Hg for a Cl⁻ determination, being the system of this type with the lowest Hg consumption. The linear working range was between 1 and 40 mg L⁻¹ Cl⁻ and the detection limit was 0.2 mg L⁻¹ Cl⁻. The repeatability (RSD) was 0.8% for a 10 mg L⁻¹ Cl⁻ solution, and the injection throughput was 130 h⁻¹. The proposed system is compared with other chloride monitoring flow systems, this comparison is realized with a point of view of the equilibrium between the obtained analytical features and produced residues toxicity. The proposed system was applied to the determination of Cl⁻ in mineral, tap and well water.     

Multicomponent analysis with a computerized flow injection system using LED photometric detection

An original computer-controlled solid-state photometer has been developed and its potential for simultaneous multicomponent flow-injection analysis of binary and ternary mixtures is demonstrated. The device is simple in construction. Its principle of operation is based on rapid sequential measurements of the absorbance of the complexes formed by the analytes with chromogenic reagents at the wavelengths corresponding to the emission maxima of three light emitting diodes (563, 580 and 638 nm).     

Selective detection in flow analysis based on the combination of immobilized enzymes and chemically modified electrodes

The combination of immobilized enzymes and amperometry to build selective detection devices in flow-injection analysis and liquid chromatography is described. The pros and cons of enzyme electrodes and of immobilized enzyme reactors are discussed. The paper concentrates on the use of immobilized dehydrogenases, oxidases, peroxidases, and on electrodes on which these enzyme reactions can be selectively followed. The work in the field by the authors is reviewed.     

An environmental friendly method for the automatic determination of hypochlorite in commercial products using multisyringe flow injection analysis

A multisyringe flow injection analysis system was used for the determination of hypochlorite in cleaning agents, by measurement of the native absorbance of hypochlorite at 292 nm. The methodology was based on the selective decomposition of hypochlorite by a cobalt oxide catalyst giving chloride and oxygen. The difference of the absorbance of the sample before and after its pass through a cobalt oxide column was selected as analytical signal. As no further reagent was required this work can be considered as a contribution to environmental friendly analytical chemistry. The entire analytical procedure, including in-line sample dilution in three steps was automated by first, dilution in a stirred miniature vessel, second by dispersion and third by in-line addition of water using multisyringe flow injection technique. The dynamic concentration range was 0.04-0.78 g L⁻¹ (relative standard deviation lower than 3%), where the extension of the hypochlorite decomposition was of 90 ± 4%. The proposed method was successfully applied to the analysis of commercial cleaning products. The accuracy of the method was established by iodometric titration.     

Design of a field flow system for the on-line spectrophotometric determination of phosphate, nitrite and nitrate in natural water and wastewater

This study describes the design and optimisation of a field flow system for the in-situ collection and on-line determination of phosphate, nitrate and nitrite by flow injection analysis-spectrophotometry. The method is based on the initial determination of phosphate as its phosphoantimonylmolybdenum blue complex which is then oxidized on-line by nitrite and the decrease in absorbance is monitored at 880 nm. Nitrate is determined as the difference between total and initial nitrite content in a separate flow after reduction to nitrite in a cadmium reductive column. The calibration curves were linear in the range 0–2.00 mg L⁻¹ P-phosphate, 0–10.00 mg L⁻¹ nitrite and 0–7.00 mg L⁻¹ nitrate with correlation coefficients of 0.9979, 0.9993 and 0.9995, respectively. The detection limits, calculated as 3S/N, were 0.15 mg L⁻¹ for P-phosphate, 0.17 mg L⁻¹ for nitrite and 0.09 mg L⁻¹ for nitrate. The reproducibility was below 3.0% (n = 7). Method validation in the analysis of natural water and wastewater samples revealed that it can efficiently be applied to the determination of the target analytes, with recoveries in the range of 92–108%. Correspondence: Athanasios G. Vlessidis, Laboratory of Analytical Chemistry, Department of Chemistry, University of Ioannina, Ioannina 45110, Greece     

Quantitative determination of chloride by means of flow injection analysis with spectrophotometric detection in the UV/VIS range

Chloride is determined indirectly by Spectrophotometric flow injection analysis. Two systems are compared, both based on the principle of ion exchange of easily detectable anions versus chloride from suitable mercury salts. The first method is based on the exchange of chloride with chloranilate which is detected at 332 nm or at 306 nm in neutral or in acidic medium respectively. In the second case, chloride reacts with Hg(SCN)₂. The liberated thiocyanate forms a strongly coloured complex with Fe(III) in acidic solution with an absorption maximum at 460 nm. Both methods have a detection limit of about 5 mol Cl^–/l (175 ng/ml). In the case of the thiocyanate method, the relative standard deviation is about 2% (7 measurements) in the range of 5 to 150 mol/l and decreases significantly to a value of approximately 0.2% at higher concentrations; for the chloranilate method it is 10% for lower and about 1% for higher concentrations respectively.     

试剂固定化的流动注射化学发光测定盐酸伊托必利

基于盐酸伊托必利在碱性条件下对铁氰化钾鲁米诺化学发光体系有较强的抑制作用,并采用离子交换固定法将鲁米诺和铁氰化钾全部固定在阴离子交换树脂上,联用流动注射技术建立了测定盐酸伊托必利的新方法。本法的线性范围为1.0~100.0μg/mL,检出限0.2μg/mL,对20μg/mL的盐酸伊托必利11次平行测定,其相对标准偏差为2.1%。单次测定在45 s内完成。此固定化柱可使用200次以上。可用于盐酸伊托必利片剂中盐酸伊托必利的质量检测。     

Single interface flow system with potentiometric detection for the determination of nitrate in water and vegetables

In this work a single interface flow system (SIFA) with potentiometric detection was for the first time implemented and applied to the determination of nitrate in waters and plant extracts. The analytical potential of the SIFA system was exploited not only to transport the sample towards detection but also to carry out, in a reproducible and automated way, the tasks associated with sample pre-treatment, namely ionic strength, pH adjustment and interfering species suppression. The advantageous aspects of combining a SIFA system with potentiometry with enhanced simplicity, ease of implementation and automation were further discussed and emphasised.The obtained results showed relative deviations lower than 5%, for both types of samples, with sampling rates of about 40 h⁻¹.In addition, an innovative and straightforward process for constructing plastic membrane ion selective electrodes with a tubular configuration able to be coupled to flow-based analytical systems is also proposed. The developed approach, consisting of assembling the electrode inside a flow tubing connector is very simple to implement, robust, particularly adequate to be combined with flow methodologies and maintains all dynamic and analytical characteristics exhibited by previous assembling processes.     

Microchemical determination of lodate and iodide in sea waters by flow injection analysis

A flow injection analysis method for iodate and iodide in sea water is described. The system involves spectrophotometric detection based on the catalytic, fading effect of either iodate or iodide on the indicator reaction of iron (III) thiocyanate and nitrite. With and without an anion-exchange column in the flow conduit, the system allows the determination of iodate and total iodine, respectively; iodide can be found by difference. Both iodate-iodine and total iodine can be determined in the range 0.75 to 150 g/1 on the sea water basis with analysis times of 20 min for iodate-iodine and 9 min for total iodine. The RSDs are within 1.3% for both iodate and iodide. Results are presented for the determination of iodate and iodide in sea waters and some brines associated with natural methane gas evolution.     

Electrochemical determination of lead(II) using a montmorillonite calcium-modified carbon paste electrode

Utilizing the fascinating properties of montmorillonite calcium (MMT-Ca), such as huge cationic exchange capacity, strong adsorptive ability, high chemical and mechanical stability, an MMT-Ca modified carbon paste electrode (CPE) was constructed for the sensitive determination of Pb²⁺. In 0.01 mol·L⁻¹ HCl, Pb²⁺ was firstly exchanged and accumulated on an MMT-Ca modified CPE surface and secondly reduced to Pb at −0.90 V. In the following potential sweep from −0.90 to −0.50 V, reduced Pb was oxidized, resulting in an obvious stripping peak at −0.58 V. After optimizing the parameters, such as determining medium, content of MMT-Ca, accumulation potential and time, an electrochemical method was developed for the analysis of Pb²⁺. Compared with bare CPE, the MMT-Ca modified CPE significantly enhances the sensitivity of Pb²⁺ analysis. The limit of detection is evaluated to be 6.0 × 10⁻⁹ mol L⁻¹ Pb²⁺. Finally, this method was successfully employed to determine trace levels of Pb²⁺ in water samples. The first two authors contribute equally do this work     

An automatic system for acidity determination based on sequential injection titration and the monosegmented flow approach

An automatic sequential injection system, combining monosegmented flow analysis, sequential injection analysis and sequential injection titration is proposed for acidity determination. The system enables controllable sample dilution and generation of standards of required concentration in a monosegmented sequential injection manner, sequential injection titration of the prepared solutions, data collecting, and handling. It has been tested on spectrophotometric determination of acetic, citric and phosphoric acids with sodium hydroxide used as a titrant and phenolphthalein or thymolphthalein (in the case of phosphoric acid determination) as indicators. Accuracy better than |4.4|% (RE) and repeatability better than 2.9% (RSD) have been obtained. It has been applied to the determination of total acidity in vinegars and various soft drinks. The system provides low sample (less than 0.3 mL) consumption. On average, analysis of a sample takes several minutes.     

Flow-through solid-phase based optical sensor for the multisyringe flow injection trace determination of orthophosphate in waters with chemiluminescence detection

In this work, a novel flow-through solid-phase based chemiluminescence (CL) optical sensor is described for the trace determination of orthophosphate in waters exploiting the multisyringe flow injection analysis (MSFIA) concept with multicommutation. The proposed time-based injection flow system relies upon the in-line derivatisation of the analyte with ammonium molybdate in the presence of vanadate, and the transient immobilisation of the resulting heteropolyacid in a N-vinylpyrrolidone/divinylbenzene copolymer packed spiral shape flow-through cell located in front of the window of a photomultiplier tube. The simultaneous injection of well-defined slugs of luminol in alkaline medium and methanol solution towards the packed reactor is afterwards performed by proper switching of the solenoid valves. Then, the light emission from the luminol oxidation by the oxidant species retained onto the sorbent material is readily detected. At the same time, the generated molybdenum-blue compound is eluted by the minute amount of injected methanol, rendering the system prepared for a new measuring cycle. Therefore, the devised sensor enables the integration of the solid-phase CL reaction with elution and detection of the emitted light without the typical drawbacks of the molybdenum-blue based spectrophotometric procedures regarding the excess of molybdate anion, which causes high background signals due to its self-reduction. The noteworthy features of the developed CL-MSFIA system are the feasibility to accommodate reactions with different pH requirements and the ability to determine trace levels of orthophosphate in high silicate content samples (Si/P ratios up to 500). Under the optimised conditions, a dynamic linear range from 5 to 50 μg P l⁻¹ for a 1.8 ml sample, repeatability better than 3.0% and a quantification limit of 4 μg P l⁻¹ were attained. The flowing stream system handles 11 analysis h⁻¹ and has been successfully applied to the determination of trace levels of orthophosphate in environmental samples such as mineral, ground, tap and pond waters as well as samples from a water-steam cycle of an incineration plant. The t-test comparison of the means for the developed optical sensor and the molybdenum-blue spectrophotometric APHA/AWWA/WPCF reference method revealed that there is no evidence of significant differences between the obtained results at the 95% confidence level.     

Preconcentration and determination of inorganic arsenic using a multisyringe flow injection system and hydride generation-atomic fluorescence spectrometry

A new multisyringe flow injection system for inorganic arsenic determination at trace levels by hydride generation-atomic fluorescence spectrometry (HGAFS) is presented. Preconcentration on a solid-phase was carried out using a column packed with an anion-exchange resin (Amberlite IRA-410). The reagents are dispensed to the system using a multisyringe burette coupled with two multi-port selection valves.

Different parameters were changing in order to make the system as effective as possible. An analytical curve was obtained for arsenic determination between 50 and 2000 ng l⁻¹. This new approach improved five times the sensitivity over a MSFIA–HGAFS technique developed previously by the authors. Detection limit of the proposed technique was (3σ_b/S) of 30 ng l⁻¹. The relative standard deviation (R.S.D.) of As at 1 μg l⁻¹ was 4.8% (n=7). A sample throughput of 10 h⁻¹ has been achieved. The proposed method has been applied to different reference solid and water materials with satisfactory results.     

Potentiometric flow injection sensing system for determination of heparin based on current-controlled release of protamine

A flow injection system incorporated with a polycation-sensitive polymeric membrane electrode in the flow cell is proposed for potentiometric determination of heparin. An external current in nano-ampere scale is continuously applied across the polymeric membrane for controlled release of protamine from the inner filling solution to the sample solution, which makes the electrode membrane regenerate quickly after each measurement. The protamine released at membrane–sample interface is consumed by heparin injected into the flow cell via their strong electrostatic interaction, thus decreasing the measured potential, by which heparin can be detected. Under optimized conditions, a linear relationship between the potential peak height and the concentration of heparin in the sample solution can be obtained in the range of 0.1–2.0 U mL⁻¹, and the detection limit is 0.06 U mL⁻¹. The proposed potentiometric sensing system has been successfully applied to the determination of heparin in undiluted sheep whole blood.     

Use of a solid-phase extraction disk module in a FI system for the automated preconcentration and determination of surfactants using potentiometric detection

The global determination of anionic surfactants is proposed by using flow injection potentiometry, and by employing specifically developed tubular flow-through ion selective electrodes (ISEs). The low concentration requirements needed for the environmental application are obtained with an on-line preconcentration stage embedded in the flow system, which has as its goal the unattended monitoring of anionic surfactants in surface waters. The on-line preconcentration is achieved by employing an octadecylsilica extraction disk in the FIA system. This stage performs the solid phase extraction (SPE) for the enrichment and purification of the target analytes from common interfering anions. The outlined procedure improves the detection limit of a direct injection system, which is decreased from 10 to 0.25 μM by using a preconcentration volume of 3.0 mL and 50 μL of 75% acetonitrile in water as the eluent. Precision was estimated as 2.9% relative standard deviation (n = 20) for a 0.25 μM (0.070 mg·L^− 1) sodium docecylsulfate standard.     

Determination of hydrogen peroxide by using a flow injection system with immobilized peroxidase and long pathlength capillary spectrophotometry

The development of a highly sensitive method for the determination of nanomolar concentrations of hydrogen peroxide in the liquid phase is described. This paper demonstrates for the first time a flow injection analysis (FIA) system with immobilized enzyme reactor combined with a total internal reflective cell (a liquid waveguide capillary cell (LWCC)) and spectrophotometric detection, for the development of an improved procedure for the determination of hydrogen peroxide. Moreover, the newly synthesized 4-aminopyrazolone derivative, 4-amino-5-(p-aminophenyl)-1-methyl-2-phenyl-pyrazol-3-one (DAP), is used as a color coupler in its oxidative condensation with the sodium salt of N-ethyl-N-sulphopropylaniline sodium salt (ALPS) which acts as a hydrogen donor. Immobilization of peroxidase is achieved by coupling the periodate-treated enzyme to aminopropyl controlled-pore glass (CPG) beads. The determination of hydrogen peroxide is carried out in a 0.1 M phosphate buffer and the product is monitored at 590 nm with a charge-coupled device (CCD) detector equipped with fiber optics in a fully computerized system. The interference of different species, mainly ionic, was investigated.The method permits detection down to 4 nmol l⁻¹ hydrogen peroxide (signal-to-noise ratio=3). A linear calibration graph was obtained over the range 20-700 nmol l⁻¹. The relative standard deviation (R.S.D.) at 300 nmol l⁻¹ H₂O₂ is 1.7% (n=7). The method was successfully applied for the determination of hydrogen peroxide in samples from a vat-cleaning process.     

Sensitive and ultra-fast determination of arsenic(III) by gas-diffusion flow injection analysis with chemiluminescence detection

A novel chemiluminescence gas-diffusion flow injection system for the determination of arsenic(III) in aqueous samples is described. The analytical procedure involves injection of arsenic(III) samples and standards into a 0.3 mol L⁻¹ hydrochloric acid carrier stream which is merged with a reagent stream containing 0.2% (w/v) sodium borohydride and 0.015 mol L⁻¹ sodium hydroxide. Arsine, generated in the combined carrier/reagent donor stream, diffuses across the hydrophobic Teflon membrane of the gas-diffusion cell into an argon acceptor stream and then reacts with ozone in the flow-through chemiluminescence measuring cell of the flow system. Under optimal conditions, the method is characterized by a wide linear calibration range from 0.6 μg L⁻¹ to 25 mg L⁻¹, a detection limit of 0.6 μg L⁻¹ and a sample throughput of 300 samples per hour at 25 mg L⁻¹ and 450 samples per hour at 25 μg L⁻¹.     

Simultaneous chemiluminescent determination of carbaryl and 1-naphthol in soils using a flow-injection system

A flow-injection method coupled with the luminol chemiluminescence (CL) detection was developed for the simultaneous determination of carbaryl and 1-naphthol in soils. The method is based on the inhibition of luminol oxidation by the presence of 1-naphthol with the consequent reduction in the CL intensity. The conversion of carbaryl into 1-naphthol was made by the alkaline hydrolysis with NaOH. Under the optimised conditions, the method permits the determination of carbaryl and 1-naphthol over the range 25–400 ng mL^?1 with high determination coefficient using both peak area and height, and high sample throughput (40 h^?1). The detection limits applying the International Unión of Pure and Applied Chemistry (IUPAC) criteria were 65 ng g^?1 and 123.5 ng g^?1 for peak height and area, respectively. A simple extraction procedure employing chloroform as the solvent and sonication was effective for the complete extraction of the analytes present in soils. The method was validated by the analysis of spiked samples, with recoveries between 88.7 and 103.1%. The Flow Injection-Chemiluminescence (FI-CL) method has proven to be simple, fast and accurate for the quantification of carbaryl and its main degradation product in soils.     

Decomposition of organoarsenic compounds by using a microwave oven and subsequent determination by flow injection-hydride generation-atomic absorption spectrometry

Environmentally important organoarsenicals such as arsenobetaine, arsenocholine and tetramethylarsonium ion do not form volatile hydrides under the commonly used analytical conditions on treatment with borohydride and it has been difficult to determine their concentrations without further derivatization. This paper describes a rapid method which completely decomposes and oxidizes these arsenicals to arsenate by using potassium persulphate and sodium hydroxide with the aid of microwave energy. The quantitative decomposition of these species permits their determination at low nanogram levels, by hydride generation atomic absorption spectromety (HG AA). A new hydride generator which has high efficiency and minimum dead volume and therefore is suitable for flow injection analysis (FIA) is also described. A system combining flow injection analysis, online microwave oven digestion, and hydride generation followed by atomic absorption measurement, is developed. This system is capable of performing analysis at a sample throughput of 100-120 per hour. Calibration curves were linear from 10 to 200 ng cm^?3 of arsenic and the detection limit was 5 ng cm^?3 for a 100-μ injection or 0.5 ng of arsenic. All ten organoarsenic compounds studied gave arsenate as the decomposition product, which was confirmed by using molybdenum blue photometric measurement.