流动注射-氢化物发生-原子吸收光谱法测定雪中的微量铅

建立了测定雪中微量铅的流动注射-氢化物发生-原子吸收光谱法。在优化条件下。测定铅的线性范围为0～52．0ng／mL，线性回归方程为A=0．018c 0．016，相关系数r=0．9995，检出限为0．2ng／mL。用于雪中微量铅的测定，加标回收率为94．2％～107．3％，相对标准偏差为1．47％～3．22％。该方法的测定结果与标准加入法基本一致。     

顶空进样气质联用法测定涂料中12种卤代烃和苯系物

采用顶空进样气质联用法测定涂料中12种卤代烃和苯系物，选用硅油作母液制备一系列标准样品，对采样温度、平衡时间以及色谱条件进行了讨论。方法也适用于溶剂型涂料和水性涂料。操作简单，定性定量准确可靠，线性范围为1-1000mg／L，最低检测浓度为0．05-0．1mg/L，方法回收率为73．4％-113．3％，相对标准偏差为2．27％-8．69％，并对实际样品进行了测定，取得满意结果。     

火焰原子吸收光谱法直接测定食用菌中的铅和镉

采用火焰原子吸收法直接测定了食用菌中铅和镉的含量。方法灵敏、准确，测定时无须富集、萃取，操作简便，快速，铅和镉的相对标准偏差分别在3．3％～7．3％和3．1％～7．5％之间。回收率在94％～106％和95％～105％之间；检出限为0．016mg/L和0．008mg/L。     

ICP-AES法测定锡精矿中锡、铜、铅、铁的含量

建立了过氧化钠熔融分解样品、电感耦合等离子发射光谱法（ICP-AES）测定锡精矿中锡、铜、铅、铁的新方法。对试样分解方法、过氧化钠用量、元素分析谱线等进行了讨论。选择过氧化钠用量为2．0g,样品熔融温度为850~C,锡、铜、铅、铁分析谱线分别为189．991,324．754,220．353,259．940nm。将该方法应用于标准样品（BY0107—1）中Sn,Cu,Pb,Fe的测定,待测元素的回收率在92．0％-101．6％之间,检出限为分别为0．006,0．002,0．005,0．001μg／mL,测定结果的相对标准偏差为0．16％～2．11％（n=5）。     

ICP-AES法同时测定锰矿石中铁、铝、钛、钙、镁、磷、钡、铅的含量

锰矿石样品用HNO3-HF-HClO4酸溶除硅后,对采用ICP-AES法测定其中的铁、铝、钛、钙、镁、磷时,同时测定钡、铅的相关条件进行了试验。主要对酸溶样能否分解重晶石或天青石等含钡矿物进行了探讨,测定了3个国家级标准样品。测定结果与标准值吻合。用标准加入法测得的钡和铅的回收率分别为96．0％-100．5％,97．1％～100．0％。用该法对含钡量较高的澳大利亚锰矿进行分析,测定结果的相对标准偏差为0-82％,并将测定结果与X荧光光谱法测定结果进行了比对。     

乙酰丙酮分光光度法测定水性涂料及胶粘剂中的甲醛含量

建立测定水性涂料和胶粘剂中甲醛含量的乙酰丙酮分光光度法。测定甲醛的线性范围为0．00～80.29μg,相关系数为0．9999,水性涂料和胶粘剂样品中甲醛含量测定结果的相对标准偏差分别为3．2％、2.8％,回收率分别为89％～93％、90％～96％。     

微波增压溶样-石墨炉原子吸收光谱法同时测定植物性样品中微量铅镉

使用微波增压溶样法，将样品用HNO3—HClO4溶解后，用石墨炉原子吸收光谱法同时测定植物性样品中铅和镉。以磷酸二氢铵—硝酸镁作为基体改进剂，可使灰化温度大大提高，克服了基体的干扰。铅和镉的回收率分别为95．3％—104．8％和96．2％—105．5％，RSD分别为4．8％-7．2％和4．3％-7．6％。     

线性扫描阳极溶出伏安法测定酒中的铅

采用线性扫描阳极溶出伏安法测定酒中铅的含量，在0．1mol/L盐酸底液中，铅的加标回收率为97．4％～101．3％，测定结果的相对标准偏差为0．76％～3．32％，线性范围为0．02～1．10mg／L。     

生物样品中Se的荧光测定方法

运用微波消化系统处理生物样品，以2，3-二氨基萘为荧光试剂建立了一种测定生物样品中Se的荧光分光光度法。方法的最低检出限为1．6ng／mL，线性范围0～0．600μg／mL，回收率92．22％～99．78％，连续10次测定样品变异系数（CV）为0．4％（n=10），隔213重复实验变异系数为1．54％。该法具有灵敏、稳定、可靠等优点，适用于生物样品中Se含量的测定。     

电感耦合等离子炬-原子发射光谱法测定铅及铅合金中的铜、银、砷

采用硝酸、酒石酸溶解样品,用电感耦合等离子炬-原子发射光谱法直接测定铅及铅合金中的铜、银、砷。该法测定速度快,测量结果的相对标准偏差为0．34％-0.49％,铜、银、砷的回收率分别为99．2％～116．7％、93．3％～101．1％、98．3％～116．O％。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.