Study on adsorption and reaction mechanism of preparation of TiO2/SiO2 by adsorption phase reactor technique

This paper approaches the evolution of adsorption layer with temperature under different water concentrations. EDX and X-ray diffraction (XRD) indicated that under low water concentration (LWC), there was a sharp decrease in TiO₂ quantity curve and grain size curve between 40 °C and 60 °C. But under high water concentration (HWC), TiO₂ quantity and grain size both rose continually. In transmission electron microscopy (TEM) picture, the characteristic of samples of LWC and HWC at low temperature were similar, whereas they became quite different at high temperature. These phenomena manifest that the effects of adsorption and reaction alter at different conditions. Under LWC, adsorption mechanism dominates the process. Under HWC, the chief mechanism at low temperature was similar to that of LWC and at high temperature the major reaction region switches from adsorption to alcohol bulk. Based on the characteristics of adsorption on silica surface, the phenomenology theory dealt with formation of adsorption layer and its evolution with temperature was proposed.     

SnO2/TiO2 mixed oxide particles synthesized in doped premixed H2/O2/Ar flames

SnO₂/TiO₂ mixed oxides with primary particle size ranging between 5 nm d_p 12 nm were synthesized by doping a H₂/O₂/Ar flame with Sn(CH₃)₄ and Ti(OC₃H₇)₄ co-currently. The effects of “flow coordinate,” concentration and flame configurations were investigated with respect to particle size and morphology of the generated mixed oxides. In situ characterization of the mixed oxides was performed using the particle mass spectrometer (PMS), while XRD, TEM, BET and UV–Vis were performed ex situ. Results obtained showed that primary particle size of mixed oxides can be controlled by varying experimental parameters. The mixed oxides have interesting properties compared to those of the pure oxides of TiO₂ and SnO₂, which were also synthesized in flames earlier. Band gap tuning opportunities are possible using mixed oxides.     

Effect of TiO2/Al2O3 film coated diamond abrasive particles by sol-gel technique

The diamond abrasive particles were coated with the TiO₂/Al₂O₃ film by the sol-gel technique. Compared with the uncoated diamonds, the TiO₂/Al₂O₃ film was excellent material for the protection of the diamonds. The results showed that the incipient oxidation temperature of the TiO₂/Al₂O₃ film coated diamonds in air atmosphere was 775 °C, which was higher 175 °C than that of the uncoated diamonds. And the coated diamonds also had better the diamond's single particle compressive strength and the impact toughness than that of uncoated diamonds after sintering at 750 °C. For the vitrified bond grinding wheels, replacing the uncoated diamonds with the TiO₂/Al₂O₃ film coated diamonds, the volume expansion of the grinding wheels decreased from 6.2% to 3.4%, the porosity decreased from 35.7% to 25.7%, the hardness increased from 61.2H_RC to 66.5H_RC and the grinding ratio of the vitrified bond grinding wheels to carbide alloy (YG8) increased from 11.5 to 19.1.     

Structural phase transitions in brookite-type TiO2 under high pressure

We have studied polycrystalline brookite TiO₂ using energy-dispersive X-ray diffraction at pressures up to 27.8 GPa and derived an ambient-pressure bulk modulus of 255 GPa using Birch-Murnaghan's equations of state with a fixed value of 4 as its first derivative. The transition from brookite-type to baddeleyite-type was observed to start at 15.8 GPa and finished at 22.8 GPa. Upon decompression, the α-PbO₂ structure appeared at 3.5 GPa and the baddeleyite-type structure remained down to 1.6 GPa, the lowest pressure in the present work.     

热处理对爆轰合成的纳米TiO_2混晶的结构相变的影响

采用爆轰法制备了纳米TiO2混晶体,初步研究了不同煅烧温度(600℃和720℃)和不同煅烧时间(1 h,2 h,3.5 h和5 h)对其微结构和结构相变行为的影响,并应用热动力学理论讨论了从锐钛矿相到金红石相的结构相变过程和相变机理.研究表明:随着煅烧温度的升高和煅烧时间的增加,纳米TiO2的粒径逐渐增大,混晶中金红石相的含量逐渐提高.与常规方法制备的纳米TiO2不同的是,在相同煅烧温度和煅烧时间下金红石相的平均生长速率明显低于锐钛矿相.锐钛矿相完全相变为金红石的温度也明显低于常规方法报道的相变温度.该研究会对控制纳米TiO2晶体尺寸和批量合成提供一定的理论和实验指导.     

Structure and composition of secondary phase particles in cobalt-doped TiO2 films

The microstructural properties of secondary phase particles formed in epitaxial Co_xTi_1−xO₂ anatase thin films grown on (0 0 1)LaAlO₃ by a reactive RF magnetron co-sputter deposition are examined. These films exhibit ferromagnetic behavior in magnetization measurements, showing a M–H loop at room temperature with a saturation magnetization on the order of 0.7 μ_B /Co. X-ray photoemission spectrometry indicates that the Co cations are in the Co²⁺ valence state. Cross-section electron microscopy reveals that a significant fraction of the cobalt segregates into Co–Ti–O secondary phase particles. Selected area electron diffraction shows that the secondary phase particles are cobalt-rich anatase. While the cobalt is concentrated in the segregated particles, local energy dispersive spectrometry indicates some Co throughout the film.     

Surface roughness analysis of hydrophilic SiO2/TiO2/glass nano bilayers by the level crossing approach

The effect of etching time on the statistical properties of hydrophilic surfaces of SiO₂/TiO₂/glass nano bilayers has been studied using atomic force microscopy (AFM) and a stochastic approach based on a level crossing analysis. We have created rough surfaces of the hydrophilic SiO₂/TiO₂ nano bilayer system by using 26% potassium hydroxide (KOH) solution. Measuring the average apparent contact angle allowed us to assess the degree of hydrophilicity, and the optimum condition was determined to be 10 min etching time. A level crossing analysis based on AFM images provided deeper insight into the microscopic details of the surface topography. With different etching times, it has been shown that the average frequency of visiting a height with positive slope behaves in a Gaussian manner for heights near the mean value and obeys a power law for heights far away from the mean value. Finally, by applying the generalized total number of crossings with positive slope, it was found that the both high heights and deep valleys of the surface have a great effect on the hydrophilic degree of the SiO₂/TiO₂/glass nano bilayer investigated system.     

Ellipsometric studies on TiO2 thin films synthesized by spray pyrolysis technique

TiO₂ thin films were synthesized on quartz substrates at substrate temperatures of 350 °C and 450 °C by thermal spray pyrolysis technique using titanium oxy-acetyl acetonate as a precursor. The optical properties of the thin films were characterized by a Spectroscopic Ellipsometer (SE). The surface morphology of the thin films was studied using Atomic Force Microscopy (AFM). The surface roughness values obtained using AFM and SE was compared. The refractive indices of the films were computed using a point by point ellipsometric data extraction procedure. The porosity of the films were modeled from the optical data by effective medium approximation and corroborated from empirical relations. Using Forouhi-Bloomer optical dispersion model, further treatment of SE data was carried out. The experimental investigations and modeling of the data were directed towards optical benchmarking of spray pyrolyzed titania thin films.     

Effect of annealing on TiO2 nanoparticles

TiO₂ nanoparticles have been prepared by simple chemical precipitation method and annealed at different temperatures. The as-prepared TiO₂ are amorphous, and they transform into anatase phase on annealing at 450 °C, and rutile phase on annealing at 900 °C. The X-ray diffraction results showed that TiO₂ nanoparticles with grain size in the range of 21–24 nm for anatase phase and 69–74 nm for rutile phase have been obtained. FESEM images show the formation of TiO₂ nanoparticles with small size in structure. The FTIR and Raman spectra exhibited peaks corresponding to the anatase and rutile structure phases of TiO₂. Optical absorption studies reveal that the absorption edge shifts towards longer wavelength (red shift) with increase of annealing temperature.     

Effect of thermal annealing on the structure and microstructure of TiO2 thin films

Nanostructured TiO₂ thin films have been prepared through chemical route using sol-gel and spin coating techniques. The deposited films were annealed in the temperature range 400–1000°C for 1 h. The structure and microstructure of the annealed films were characterized by GAXRD, micro-Raman spectroscopy and AFM. The as-deposited TiO₂ thin films are found to be amorphous. Micro-Raman and GAXRD results confirm the presence of the anatase phase and absence of the rutile phase for films annealed up to 700°C. The diffraction pattern of the film annealed at 800 to 1000°C contains peaks of both anatase and rutile reflections. The intensity of all peaks in micro-Raman and GAXRD patterns increased and their width (FWHM) decreased with increasing annealing temperature, demonstrating the improvement in the crystallinity of the annealed films. Phase transformation at higher annealing temperature involves a competition among three events such as: grain growth of anatase phase, conversion of anatase to rutile and grain growth of rutile phase. AFM image of the asdeposited films and annealed films indicated exponential grain growth at higher temperature.      

纳米TiO2薄膜的低温等离子体制备技术

以四氯化钛为源物质,氩气为载气,氧气为反应气体,利用低温等离子体增强化学气相沉积在硅基表面制备出了TiO2薄膜。使用场发射扫描电子显微镜、X射线衍射仪等检测分析表征TiO2薄膜的性能与性质,并探讨了工艺条件如基片材料、沉积时间和基片温度对薄膜性能的影响。结果表明：制备的薄膜表面光滑均匀,结构致密,最小晶粒尺寸约15 nm;薄膜的晶型主要依赖于沉积温度,低于300 ℃沉积的薄膜是无定形的,300 ℃之上沉积的薄膜是锐钛矿结构。     

Raman spectra of TiO2-II,TiO2-III,SnO2, and GeO2 at high pressure

Raman spectra of the orthorhombic (II) and high pressure (III) phases of titanium dioxide at pressures to 372 kbar and effects of temperature and hydrostatic pressure on Raman spectra of the tetagonal cassiterite-like phases of TiO₂, GeO₂ and SnO₂ are described. At room temperature, the TiO₂ II–III transition is sluggish, and metastable coexistence was observed from 200 to 300 kbar. The Raman spectra of TiO₂-III imply that its primitive cell contains at least four formula units; however, the structure could not be established from the Raman spectra and available powder X-ray diffraction patterns.The temperature and pressure dependences of the spectrum of the tetragonal MO₂ phases together with bulk moduli and thermal expansion data were used to evaluate the pure-volume and pure-temperature contributions to the isobaric temperature dependence of the Raman frequencies. Large anharmonicities in TiO₂ are attributed to hybridization of the oxygen p states with the d states of the Ti ion. GeO₂, where p-electron bonding is involved, is much less Enharmonic.     

Probing reaction mechanisms in mixed phase TiO2 by EPR

Charge separation processes in mixed phase TiO₂ photocatalysts are investigated by electron paramagnetic resonance (EPR) spectroscopy. The mechanisms of interfacial electron transfer, subsequent charge migration and recombination at surface sites, and other interfacial effects on chlorophenol/TiO₂ chemistry have been probed. Distorted interfacial sites have been observed and are proposed as catalytically reactive hot spots. This detailed knowledge of charge transfer processes is critical to the nanoscale design of catalysts and subsequent improvement of catalytic efficiency.     

Photocatalytic activity of dc magnetron sputter deposited amorphous TiO2 thin films

For photocatalytic thin film applications TiO₂ is one of the most important materials. The most studied TiO₂ crystal phase is anatase, though also rutile and brookite show good photoactivity. Usually anatase or a mixture of rutile and anatase is applied for powder or thin film catalysts. It has been claimed that amorphous films do not exhibit any or only a very low photocatalytic activity.We have deposited amorphous thin films by dc magnetron sputtering from sub-stoichiometric TiO_2−x targets. The coatings are transparent and show a photocatalytic activity half of that of a thin layer of spin-coated reference photocatalyst powder. Annealing the thin films to yield anatase crystallization more than doubles their photocatalytic activity. At the same film thickness these thin films show the same activity as a commercially available photocatalytic coating.The dependence of the photocatalytic activity on deposition parameters like gas pressure and sputter power is discussed. A decrease in film density, as deduced from the refractive index and the microstructure, resulted in an increase in photocatalytic activity. Film thickness has a marked influence on the photocatalytic activity, showing a strong increase up to 300-400 nm, followed by a much shallower slope.     

Effect of hydrostatic pressure on the Raman spectrum of anatase (TiO2)

Raman spectra of anatase have been investigated under pressures up to 60 kbar and at room temperature. A pressure-induced phase transition is observed at pressures above 25.6 kbar. The 197 cm^-1 mode (at 1 atm.) of six Raman active modes exhibits anomalous pressure dependence in which the frequency decreases with increasing pressure. This mode may be significant in the phase transition. The remaining modes show usual behavior.     

Characterization of TiO2/Au/TiO2 films deposited by magnetron sputtering on polycarbonate substrates

Transparent and conducting TiO₂/Au/TiO₂ (TAuT) films were deposited by reactive magnetron sputtering on polycarbonate substrates to investigate the effect of the Au interlayer on the optical, electrical, and structural properties of the films. In TAuT films, the Au interlayer thickness was kept at 5 nm. Although total thickness was maintained at 100 nm, the stack structure was varied as 50/5/45, 70/5/25, and 90/5/5 nm.In XRD pattern, the intermediate Au films were crystallized, while all TAuT films did not show any diffraction peaks for TiO₂ films with regardless of stack structure. The optical and electrical properties were dependent on the stack structure of the films. The lowest sheet resistance of 23 Ω/□ and highest optical transmittance of 76% at 550 nm were obtained from TiO₂ 90 nm/Au 5 nm/TiO₂ 5 nm films. The work function was dependent on the film stack. The highest work function (4.8 eV) was observed with the TiO₂ 90 nm/Au 5 nm/TiO₂ 5 nm film stack. The TAuT film stack of TiO₂ 90 nm/Au 5 nm/TiO₂ 5 nm films is an optimized stack that may be an alternative candidate for transparent electrodes in flat panel displays.     

Characteristics of N-doped TiO2 thin films grown on unheated glass substrate by inductively coupled plasma assisted dc reactive magnetron sputtering

N-doped TiO₂ thin films have been deposited on unheated glass substrates by an inductively coupled plasma (ICP) assisted direct current (dc) reactive magnetron sputtering. All films were produced in the metallic mode of sputtering in order to achieve a high deposition rate. The structures and properties of the N-doped TiO₂ films were studied by X-ray diffraction, X-ray photoelectron spectroscopy, transmission electron microscopy, field emission scanning electron microscopy and UV–Vis spectrophotometer. Experimental results show that we can obtain well crystallized N-doped anatase phase TiO₂ thin films at low deposition temperature and at high deposition rate by using the ICP assisted dc reactive magnetron sputtering process. The doping of nitrogen into TiO₂ lattices leads to a smooth shift of the absorption band toward visible light regions.     

Characterization of nanosized TiO2 synthesized inside a porous glass-ceramic monolith by metallo-organic decomposition process

This work reports the preparation of TiO₂ by decomposition of a metallo-organic precursor (MOD process) in the pores of an α-NbPO₅ glass-ceramic monolith (PGC-NbP) and the study of the TiO₂ anatase-rutile transition phase. The impregnation of titanium di-(propoxy)-di-(2-ethylhexanoate) in the PGC-NbP was confirmed by diffuse reflectance infrared spectroscopy. In the restrictive porous environment the decomposition of the metallo-organic compound exhibits a lower initial decomposition temperature but a higher final decomposition temperature, in comparison to the free precursor. The pure TiO₂ rutile phase is formed only above 700 °C when the titanium precursor is decomposed outside the pores. The TiO₂ anatase obtained inside the PGC-NbP was stabilized up to 750 °C and exhibits a smaller average crystallite size in comparison with the MOD process performed without PGC-NbP. Furthemore, the temperature of the TiO₂ anatase-rutile transformation depends on crystallite size, which was provided by XRD and Raman spectroscopy. The precursor impregnation-decomposition cycle revealed a linear mass increment inside PGC-NbP. Micro-Raman spectroscopy shows the presence of a gradient concentration of the TiO₂ inside the PGC-NbP. The use of the MOD process in the PGC-NbP pores has several advantages: control of the amount and the nature of the phase formed and preservation of the pore structure of PGC-NbP for subsequent treatments and reactions.     

Formation of nanotubes TiO2 from layered titanate particles by a soft chemical process

Nanotubes TiO₂ were synthesized from layered titanate Na₂Ti₃O₇ particles by a soft chemical process. These nanotubes have a hollow structure with an opening end. The wall of nanotubes is very well crystallized multi-wall structure. The inner diameters of nanotubes are ca. 30-40 nm and the length up to several hundreds nanometers. XRD results show that TiO₂ phase was formed during the procedure of exfoliating Na₂Ti₃O₇ particles into nanosheets. Based on our experimental results, an exfoliating-rolling model was proposed for formation of nanotube structure.