Determination of avilamycin in poultry feeds by liquid chromatography.

Avilamycin was extracted from feed with acetonitrile. Isolation of avilamycin factors from feed matrix interference was accomplished by normal-phase solid-phase extraction with silica as sorbent. Reversed-phase liquid chromatography was subsequently used to separate and quantitate the primary biologically active factors A and B for determination of chemical potency. This method combines specificity for avilamycins A and B in poultry feeds with simple sample preparation that removes matrix interferences. Recoveries of factor A ranged from 93.29 to 97.26%, with precision (relative standard deviation) ranging from 1.1 to 3.4%. Avilamycin factors in feed samples tested ranged from 4.45 to 17.82 micrograms/g for factor A and from 0.80 to 3.18 micrograms/g for factor B.     

Determination of nicarbazin in feeds using liquid chromatography-electrospray mass spectrometry

A method is presented for the determination of the 4,4'-dinitrocarbanilide component of the coccidiostat nicarbazin in animal feeds. Samples are extracted by shaking with methanol and analysed, without further clean-up, using liquid chromatography-electrospray mass spectrometry. A deuterated form of the analyte is employed as internal standard to improve the repeatability of the method. The method has been validated at levels between 0.1 and 100 mg kg-1 with internal standard corrected recoveries between 88 and 101% and RSD values < 8%.     

Determination of clopidol residues in chicken tissues by liquid chromatography: collaborative study

Eighteen laboratories participated in a collaborative study on the determination of clopidol residues in chicken muscle tissues by liquid chromatography. Of these, results from 16 laboratories which rigorously followed the method were subjected to statistical analysis. The method performance was assessed by all participants using 14 samples of chicken muscle fortified at concentrations ranging from 0.1 to 5.0 mg/kg. In addition, 9 participants each reported results for 6 clopidol-incurred samples in chicken muscle. Test portions were extracted with acetonitrile, and the extracts were purified with alumina and anion exchange resin solid-phase extraction cartridges in sequence. Clopidol was separated by reversed-phase liquid chromatography and quantified at 270 nm. Average recoveries ranged from 81.8 to 85.4%, reproducibility relative standard deviation (RSDR) ranged from 11.9 to 22.6%, and repeatability relative standard deviation (RSDr) ranged from 9.9 to 15.1%. For clopidol-incurred samples at concentrations of 0.100-0.687 mg/kg, the mean determination value range was 0.099-0.659 mg/kg; RSDR was 12.6-19.8%, RSDr was 3.1-8.5%; and HORRAT values were 0.7-1.1. The accuracy and precision of the method are in conformity with the requirements specified by AOAC INTERNATIONAL. The method was adopted Official First Action in April 2003.     

液相色谱-电喷雾串联质谱法测定禽类产品中克球酚的残留

建立了禽类产品中克球酚残留的液相色谱-电喷雾串联质谱(LC-ESI-MS/MS)检测方法。用甲醇对样品进行提取,提取液用正己烷萃取去油脂,然后用LC-18柱和阴离子交换柱净化,LC-ESI-MS/MS测定。利用基质校正曲线对克球酚准确定量。在2,5,10,20 μg/kg 4个添加水平下,克球酚的平均回收率稳定在55.38%～132.44%之间,日内精密度小于9.54%,日间精密度小于15.27%。在1～40 μg/kg范围内色谱峰面积与克球酚含量呈良好的线性关系,检出限为0.5 μg/kg,定量限为2.0 μg/kg。该方法选择性好,抗干扰能力强,可作为禽类产品中克球酚残留检测的确证方法。     

Determination of tylosin in feeds by liquid chromatography with solid-phase extraction

A method was developed for the determination of tylosin in feeds. The method involves extraction of tylosin with methanol, concentration under a stream of nitrogen, and cleanup using Phenomenex C18 solid-phase extraction cartridge. Analyte separation and quantitation were achieved by gradient reversed-phase liquid chromatography and UV absorbance at 285 nm with a reference wavelength of 320 nm with column temperature of 45 degrees C. Average spike recoveries for samples prepared at 4 spiking levels (22.7, 181, 907, and 1000 g/ton) were 111.0, 94.9, 96.2, and 98.6%, respectively. The overall method precision at each of the 4 spiking levels was < or = 7.85% relative standard deviation. The limits of detection and quantitation (g/ton) were 2.16 and 7.20 g/ton, respectively.     

Determination of clopidol residues in chicken tissues by liquid chromatography: part II. Distribution and depletion of clopidol in chicken tissues

A study was made of the distribution and depletion of clopidol residues at different tissue locations in chickens fed with feeds incurred with clopidol. Experiments showed that the residue levels were not identical at 5 different tissue locations in each chicken. The sequence of residue levels from high to low was livers, kidneys, upper breast, lower breast, and leg meat. The maximum residue values after suspension of the drug for 8 h were (mg/kg): livers, 4.600; kidneys, 3.619; upper breast, 1.742; lower breast, 1.641; leg meat, 1.525. The averages were taken after values for 10 chickens were determined. After suspension of the drug for 3 days, >80% residue clopidol was depleted, and the depletion was nearly completed within 7 days. The speed of depletion varied at different tissue locations in each chicken, with the sequence from fast to slow being equivalent to that of the residue levels. Analytical results of 350 samples during 7 days showed that the proposed method is specific for determination of clopidol in chickens.     

Determination of decoquinate in animal feeds by liquid chromatography: collaborative study

The performance characteristics of a liquid chromatographic (LC) method for the analysis of decoquinate (DEC) in supplements, premixes, and complete animal feeds at medicating and trace levels were collaboratively studied. DEC is extracted from ground feed samples with 1% calcium chloride-methanol solution using mechanical agitation for 90 min. After centrifugation for 5 min and dilution (if necessary), an aliquot of the extract is diluted with water. The diluted extracts are filtered and analyzed by reversed-phase LC with fluorescence detection. Suspect positive trace-level samples are confirmed by using an alternate excitation wavelength. Fourteen test samples of medicated feeds, supplement, and medicated premix, along with 8 test samples for trace-level analysis, were sent to 13 collaborators (one in Canada, 4 in Europe, and 8 in the United States). Test samples were analyzed as blind duplicates. Acceptable results were received from 12 laboratories for the medicated test samples and from 13 laboratories for the trace-level samples. Repeatability relative standard deviation estimates ranged from 1.3 to 5.6%. Reproducibility relative standard deviations estimates ranged from 2.8 to 6.1%, and HorRat values ranged from 0.22 to 0.74.     

Determination of penicillin G in feeds by liquid chromatography with solid-phase extraction

A liquid chromatographic method was developed for the determination of penicillin G in feeds. The method involves extraction of penicillin G with methanol, concentration under a stream of nitrogen, and cleanup using Phenomenex Strata-X solid-phase extraction cartridge. Analyte separation and quantification were achieved by gradient reversed-phase liquid chromatography and ultraviolet absorbance at 230 nm. Average spike recoveries for samples prepared at 3 spiking levels (25, 50, and 200 g/ton) were 96.3, 92.1, and 88.6%, respectively. The overall method precision at each of the 3 spiking levels was < or = 5.39% relative standard deviation. The limits of detection and quantititation (g/ton formulation) were 3.89 and 13.0 g/ton, respectively.     

Liquid chromatographic determination of nicarbazin in feeds

A new liquid chromatographic method has been developed for determination of nicarbazin in feeds. Approximately 40 g feed is extracted with 200 mL acetonitrile-water (80 + 20, v/v). An aliquot of the extract is filtered and assayed using a reversed-phase isocratic method that measures the 4,4'-dinitrocarbanilide moiety of nicarbazin at a wavelength of 340 nm. For medicated feeds, the method uses a standard linear range of 5 to 100 microg/mL. For lower levels, a linear range of 50 to 150 ng/mL can be used. The method has a limit of detection of 250 ng/g and a limit of quantitation of 500 ng/g in a 40 g feed sample. Recovery was 99.1%, with a range of 95.2 to 101.8%. In the typical U.S. dosing range of 27 to 113.5 g/ton, the precision of the method based on one analyst, one day, and 2 weighings ranged from 2.8% (113.5 g/ton) to 4.7% (27 g/ton).     

固相萃取-高效液相色谱测定饲料中新橙皮苷二氢查耳酮和柚皮苷二氢查耳酮

建立了固相萃取-高效液相色谱检测饲料中新橙皮苷二氢查耳酮（NHDC）和柚皮苷二氢查耳酮（Naringin DC）的方法。采用纯甲醇溶液进行超声辅助萃取样品，经HLB固相萃取柱净化后在XB-C₁₈（150 mm×4.6 mm，5 μm）色谱柱上分离，用甲醇/水作为流动相进行梯度洗脱，光电二极管阵列检测器进行检测。结果表明，新橙皮苷二氢查耳酮和柚皮苷二氢查耳酮在0.2~49.0 mg/L范围内具有良好的线性关系，相关系数均>0.999，定量限分别为0.02和0.01 mg/kg。日内和日间精密度分别为0.7%~4.1%和0.9%~6.0%。方法的加标回收率为86.2%~105.0%，相对标准偏差（RSDs）为1.0%~6.3%（n=3）。该方法能有效降低饲料基体成分的干扰，灵敏度高，重现性好，适用于饲料中新橙皮苷二氢查耳酮和柚皮苷二氢查耳酮的定量检测。     

Determination of lasalocid sodium in animal feeds and premixes by reversed-phase liquid chromatography: collaborative study

A liquid chromatographic (LC) method for the analysis of lasalocid sodium in premixes, complete animal feeds, and trace-level feeds was collaboratively studied. The method employs a 0.5% HCI acidified methanol extraction followed by 20 min sonication in a water bath heated to 40 degrees C. Samples are then shaken on a mechanical shaker for 1 h and stored overnight, followed by an additional 10 min shaking the following morning. Sample extracts are diluted if necessary with extractant, filtered, and injected onto an LC system. Determination of all lasalocid homologs is by reversed-phase LC with fluorescence detection at 314 nm excitation and 418 nm emission. Eight samples of drug premixes, medicated feeds, and mineral supplements, along with 2 samples for trace-level analysis were sent to 20 collaborators in the United States, Canada, and The Netherlands. Study data were returned by 17 laboratories. Two additional supplemental trace-level samples and a blank feed were provided to 15 of the collaborating laboratories, and test data were received from all 15 participants. For the drug premixes, medicated feeds, and mineral supplements, RSDr values (within-laboratory repeatability) ranged from 1.2 to 19.9%, RSDR values (among-laboratory reproducibility) ranged from 3.4 to 32.3%, and HorRat values ranged from 0.35 to 3.73. For the trace-level samples, only lasalocid A, the predominant homolog comprising > 90% of the sum of all homolog peak area, was quantified. All laboratories correctly identified the analyte. Although some instrument response was reported by a number of laboratories for the blank feed, all but one laboratory's results were well below the 1 mg/kg limit of quantification. RSDr values for the initial 2 trace-level samples were excessive, ranging from 51.6 to 64.4%. RSDR values ranged from 51.6 to 75.7%, and HorRat values ranged from 3.6 to 4.0. Data for the initial trace-level samples indicated that the test samples were improperly prepared to ensure homogeneity, and a new set of supplemental samples was provided to collaborators, with significantly improved results. RSDr values for the 2 supplemental trace-level samples ranged from 1.6 to 2.5%, RSDR values ranged from 5.6 to 9.2%, and HorRat values ranged from 0.43 to 0.62.     

Determination of clopidol residues in chicken tissues by high-performance liquid chromatography-mass spectrometry

A high-performance liquid chromatographic-mass spectrometric (HPLC-MS) method has been developed for determination of clopidol residues in chicken tissues. Samples are extracted with acetonitrile. The extracts are cleaned up on an alumina column followed by an anion-exchange column. The clopidol is separated on a column (150 cmx4.6 mm) of Intertsil by using acetonitrile-water (20:80) as mobile phase. The clopidol was qualitatively identified by molecule mass and determined quantitatively by selected ion monitoring mode at 190 m/z. The recoveries with RSDs ranged from 91.6+/-10.1 to 97.3+/-5.7 at 0.010 to 10.0 mg/kg by spiking three matrices (chicken muscle, liver, and kidney). The limit of detection was 0.005 mg/kg, and the limit of quantification was 0.010 mg/kg.     

Determination of methylbenzoquate in premixes and animal feeds using liquid chromatography with fluorescence detection

A rapid analytical procedure was developed and tested for routine identification and quantification of methylbenzoquate in feeds by liquid chromatography (LC). The ground feed samples were extracted using methanol-water (80 + 20, v/v) at 65 degrees-70 degrees C in a water bath for premixes and in dichloromethane at 45 degrees C in a water bath for final feeds, respectively. The extract of final feeds was cleaned using solid-phase extraction on silica columns. Both the final feed and premix extracts were analyzed by reversed-phase LC on a NovaPak C18 column (3.9 x 150 mm; 4 microm) with methanol-acetonitrile-water-phosphoric acid (340 + 350 + 308 + 2, v/v) as mobile phase. Fluorescence detection was performed at excitation and emission wavelengths of 265 and 390 nm, respectively. Alternatively, post-column addition of sulfuric acid solution was used to decrease the determination limit. The recovery of methylbenzoquate, in a concentration range of 0.5-10 mg/kg, was 105.0 +/- 7.3%. The limit of quantitation, based on a signal-to-noise ratio of 10:1, was 48 microg/kg. The developed LC method was tested in an interlaboratory study. The interlaboratory repeatibility for both samples ranged from 7.1 to 10.6%; the interlaboratory reproducibility ranged from 11.7 to 15.2%. With the post-column addition of sulfuric acid, the limit of quantification was decreased by a factor of 50. Overall, the developed method is highly selective and can be used in routine analysis.     

液相色谱串联质谱测定畜禽肉中黄霉素A的残留量

建立了高效液相色谱串联质谱法测定畜禽肉中黄霉素A残留量的方法,样品中残留的黄霉素A经提取,HLB柱净化后,以Agilent Ecillps C18色谱柱为分析柱,乙腈-10 mmol/L的乙酸铵为梯度洗脱液,经串联四极杆质谱多反应监测模式检测,黄霉素A得到了很好的分离。线性范围为10～1000μg/kg。黄霉素A的定量限为10μg/kg。添加浓度在10～50μg/kg时,回收率在70%～100%之间,变异系数在4.6%～8.8%之间。方法适合出口畜禽肉及组织中黄霉素A残留量的测定。