A photoelectrochemical (PEC) aptasensor for the highly sensitive and specific detection of thrombin is described. This aptasensor is based on an indium tin oxide (ITO) support that is covered with carbon quantum dot (CQD)-sensitized TiO2 and acts as a photoactive matrix. The ITO/TiO2/CQD electrode was prepared by impregnation assembly. It displays an enhanced and steady photocurrent response under irradiation by visible light. A carboxyl-functionalized thrombin-binding aptamer was covalently immobilized on the modified ITO to obtain a PEC aptasensor whose photocurrent decreases with increasing concentration of thrombin. Under 420 nm irradiation at a bias voltage of 0 V, the aptasensor has a linear response in the 1.0 to 250 pM thrombin concentration range, with a 0.83 pM detection limit. Conceivably, this approach can be extended to numerous other PEC aptasensors for the detection of targets for which appropriate aptamers are available.
Graphical abstract Schematic of a PEC aptasensor for thrombin. It is based on the use of CQD as the sensitizer, TiO2/CQDs as the photoactive matrix, and the thrombin aptamer as the recognition element.
An electrochemical microsensor for chloramphenicol (CAP) was fabricated by introducing magnetic Fe3O4 nanoparticles (NPs) onto the surface of activated carbon fibers. This microsensor exhibited increased electrochemical response toward CAP because of the synergetic effect of the Fe3O4 NPs and the carbon fibers. Cyclic voltammograms were acquired and displayed three stable and irreversible redox peaks in pH 7.0 solution. Under optimized conditions, the cathodic current peaks at ?0.67 V (vs. Ag/AgCl). The calibration plot is linear in the 40 pM to 1 μM CAP concentration range, with a 17 pM detection limit (at a signal-to-noise ratio of 3). The sensor was applied to the determination of CAP in spiked sediment samples. In our perception, this electrocatalytic platform provided a useful tool for fast, portable, and sensitive analysis of chloramphenicol.
Graphical abstract A sensitive carbon fiber microsensor modified with Fe3O4 nanoparticles is found to display two cathodic peaks when detecting chloramphenicol at 100 mV·s?1 and at pH 7.0. The sensor was applied to the determination of chloramphenicol in sediment samples.
The article describes a method for determination of tannic acid in extracts of medicinal plants. Tannic acid (TA) is an antioxidant and has anticancer and antimicrobial properties. Titanium dioxide nanoparticles (TiO2) were co-sensitized with 5-methylphenazinium methosulfate (PMS) and carboxy-functionalized cadmium telluride quantum dots (CdTe QDs), and immobilized on a fluorine-doped tin oxide electrode. The surface morphology and electrochemical properties of the modified electrode were investigated by scanning electron microscopy and amperometry, respectively. A composite consisting of TiO2, PMS and CdTe QDs in a nafion film has a response to TA under LED light higher than that observed for each separate component. Under optimized experimental conditions and at an applied voltage of +0.4 V vs Ag/AgCl, the photoelectrochemical sensor has a linear response in the 0.2 to 200 μmol L?1 TA concentration range and a detection limit of 60 nmol L?1. The sensor was successfully applied to the determination of TA in spiked extracts from three medicinal plants, with recovery values between 98.3 and 103.9 %.
Graphical abstract Schematic diagram for photoelectrochemical detection of tannic acid based on a fluorine doped tin oxide electrode modified with titanium oxide, 5-methylphenazinium methosulfate and carboxy-functionalized cadmium telluride quantum dots
A novel photoelectrochemical (PEC) aptasensor with graphitic-phase carbon nitride quantum dots (g-C3N4; QDs) and reduced graphene oxide (rGO) was fabricated. The g-C3N4 QDs possess enhanced emission quantum yield (with an emission peak at 450 nm), improved charge separation ability and effective optical absorption, while rGO has excellent electron transfer capability. Altogether, this results in improved PEC performance. The method is making use of an aptamer against sulfadimethoxine (SDM) that was immobilized on electrode through π stacking interaction. Changes of the photocurrent occur because SDM as a photogenerated hole acceptor can further accelerate the separation of photoexcited carriers. Under optimized conditions and at an applied potential of +0.2 V, the aptasensor has a linear response in the 0.5 nM to 80 nM SDM concentration range, with a 0.1 nM detection limit (at S/N =?3). The method was successfully applied to the analysis of SDM in tap, lake and waste water samples.
Graphical abstract Graphitic-phase carbon nitride (g-C3N4) quantum dots (QDs) and reduced graphene oxide (rGO) were used to modify fluorine-doped SnO2 (FTO) electrodes for use in a photoelectrochemical (PEC) aptasensor. SDM oxidized by the hole on valance band (VB) of g-C3N4 QDs promote the separation of electron in the conductive band (CB), which made the changes of photocurrent signal.
The authors describe a dye-sensitized photoelectrochemical immunoassay for the tumor marker carcinoembryonic antigen (CEA). The method employs the rhodamine dye Rh123 with red color and absorption maximum at 500 nm for spectral sensitization, and a 3D nanocomposite prepared from graphene oxide and MoS2 acting as the photoelectric conversion layer. The nanocomposite with flower-like 3D architectures was characterized by transmission electron microscopy, scanning electron microscopy, X-ray powder diffraction, and UV-vis diffuse reflectometry. A photoelectrochemical sandwich immunoassay was developed that is based on the use of the nanocomposite and based on the specific binding of antibody and antigen, and by using a secondary antibody labeled with Rh123 and CdS (Ab2-Rh123@CdS). Under optimal conditions and at a typical working voltage of 0 V (vs. Hg/HgCl2), the photocurrent increases linearly 10 pg mL?1 to 80 ng mL?1 CEA concentration range, with a 3.2 pg mL?1 detection limit.
Graphical abstract Flower-like GO-MoS2 complex with high efficiency of electron transport was synthesized to construct photoelectrochemical platform. The sandwich-type immunoassay was built on this platform based on specific binding of antigen and antibody. Carcinoembryonic antigen in sample was detected sensitively by using sensitization of rhodamine dye Rh123 as signal amplification strategy.
The authors describe an ethylene glycol assisted precipitation method for synthesis of Er(III)/Yb(III)-doped BiF3 nanoparticles (NPs) at room temperature. Under 980-nm light irradiation, the NPs emit upconversion (UC) emission of Er(III) ions as a result of a two-photon absorption process. The temperature-dependent green emissions (peaking at 525 and 545 nm) are used to establish an unambiguous relationship between the ratio of fluorescence intensities and temperature. The NPs have a maximum sensitivity of 6.5?×?10?3 K?1 at 619 K and can be applied over the 291–691 K temperature range. The results indicate that these NPs are a promising candidate for optical thermometry.
Graphical abstract Schematic of the room-temperature preparation of Er(III)/Yb(III)-doped BiF3 nanoparticles with strongly temperature-dependent upconversion emission.
This review (with (318) refs) describes progress made in the design and synthesis of morphologically different metal oxide nanoparticles made from iron, manganese, titanium, copper, zinc, zirconium, cobalt, nickel, tungsten, silver, and vanadium. It also covers respective composites and their function and application in the field of electrochemical and photoelectrochemical sensing of chemical and biochemical species. The proper incorporation of chemical functionalities into these nanomaterials warrants effective detection of target molecules including DNA hybridization and sensing of DNA or the formation of antigen/antibody complexes. Significant data are summarized in tables. The review concludes with a discussion or current challenge and future perspectives.
Tungsten disulfide (WS2) nanosheets were obtained by exfoliating WS2 bulk crystals in N-methylpyrrolidone by ultrasonication. Gold nanoparticles (GNPs) were synthesized by in-situ ultrasonication of sodium citrate and HAuCl4 while fabricating the WS2 nanosheets. In this way, the GNPs were self-assembled on WS2 nanosheets to form a GNPs/WS2 nanocomposite through interaction between sulfur and gold atoms. The photoelectrochemical response of WS2 nanosheets is significantly enhanced after integration of the GNPs. The GNPs/WS2 nanocomposite was coated onto a glassy carbon electrode (GCE) to construct a sensing interface which then was modified with an antibody against the carcinoembryonic antigen (CEA) to obtain a photoelectrochemical immunosensor for CEA. Under optimized conditions, the decline in relative photocurrent is linearly related to the logarithm of the CEA concentration in the range from 0.001 to 40 ng mL?1. The detection limit is 0.5 pg mL?1 (at S/N =?3). The assay is sensitive, selective, stable and reproducible. It was applied to the determination of CEA in clinical serum samples.
Graphical abstract Schematic presentation of the fabrication of Au/WS2 nanocomposites by in-situ ultrasonication and the procedure for the CEA photoelectrochemical immunosensor preparation, and the photocurrent response towards the carcinoembryonic antigen.
A voltammetric sensor is described for the quantitation of propyl gallate (PG). A screen-printed carbon electrode (SPCE) was modified with reduced graphene sheets that were decorated with cobalt diselenide nanoparticles (CoSe2@rGO). The material was hydrothermally prepared and characterized by several spectroscopic techniques. The modified SPCE displays excellent electrocatalytic ability towards PG. Differential pulse voltammetry, with a peak voltage at 0.34 V (vs. Ag/AgCl) has a sensitivity of 12.84 μA·μM?1·cm?2 and a detection limit as low as 16 nM. The method is reproducible, selective, and practical. This method was applied to the determination of PG in spiked meat samples, and the result showed an adequate recovery.
The authors describe an amperometric sensor for dopamine (DA) by employing olive-like Fe2O3 microspheres (OFMs) as the electrocatalyst for DA oxidization. The OFMs were prepared by using a protein templated method. The structure and properties of the OFMs were characterized by scanning electron microscopy, X-ray powder diffraction, energy dispersive x-ray spectroscopy, cyclic voltammetry and electrochemical impedance spectroscopy. The OFMs possess excellent catalytic activity towards DA oxidization due to their unique morphology. The sensor responds to DA within less than 5 s. The sensor, best operated at a voltage of +0.2 V (vs. SCE) responds linearly in the 0.2 to 115 μM DA concentration range and has a 30 nM detection limit. The selectivity, reproducibility and long-term stability of the sensor are acceptable. It performs well when applied to spiked human urine samples.
Graphical abstract Olive-like Fe2O3 microspheres (OFMs), synthesized using egg white as template, display excellent catalytic activity towards dopamine (DA) oxidization due to their unique morphology. They were applied for DA detection using the amperometric technique. The electrochemical sensor exhibited a high sensitivity and a 30 nM detection limit. DAQ: dopaquinone.
Ionic liquid coated nanoparticles (IL-NPs) consisting of zero-valent iron are shown to display intrinsic peroxidase-like activity with enhanced potential to catalyze the oxidation of the chromogenic substrate 3,3′,5,5′-tetramethylbenzidine (TMB) in the presence of hydrogen peroxide. This results in the formation of a blue green colored product that can be detected with bare eyes and quantified by photometry at 652 nm. The IL-NPs were further doped with bismuth to enhance its catalytic properties. The Bi-doped IL-NPs were characterized by FTIR, X-ray diffraction and scanning electron microscopy. A colorimetric assay was worked out for hydrogen peroxide that is simple, sensitive and selective. Response is linear in the 30–300 μM H2O2 concentration range, and the detection limit is 0.15 μM.
Graphical abstract Schematic of ionic liquid coated iron nanoparticles that display intrinsic peroxidase-like activity. They are capable of oxidizing the chromogenic substrate 3,3′,5,5′-tetramethylbenzidine (TMB) in the presence of hydrogen peroxide. This catalytic oxidation generated blue-green color can be measured by colorimetry. Response is linear in the range of 30–300 μM H2O2 concentration, and the detection limit is 0.15 μM.
A method is described for the fluorometric determination of hypochlorite. It is making use of molybdenum disulfide quantum dots (MoS2 QDs) as a fluorescent probe. The QDs are prepared by hydrothermal reaction of sodium molybdate with glutathione. They possess diameters typically ranging from 1.4 to 3.8 nm, excellent stability in water, and blue photoluminescence (with excitation/emission peaks located at 315/412 nm and a quantum yield of 3.7%). The fluorescence of the QDs is statically quenched by hypochlorite, and the Stern-Volmer plot is linear. Hypochlorite can be detected in the 5–500 μM concentration range with a 0.5 μM detection limit. The method has been successfully applied to the determination of hypochlorite in spiked samples of tap water, lake water, and commercial disinfectants.
Graphical abstract Schematic of a method for the fluorometric determination of hypochlorite using MoS2 quantum dots as a fluorescent probe. It has been applied to hypochlorite assay in spiked samples of tap water, lake water, and commercial disinfectants.
A magnetic sorbent was fabricated by coating the magnetized graphene oxide with polystyrene (PS) to obtain a sorbent of the type GO-Fe3O4@PS. The chemical composition and morphology of the sorbent were characterized. The sorbent was employed for the enrichment of polycyclic aromatic hydrocarbons (PAHs) from water samples. Various parameters affecting the enrichment were investigated. The PAHs were then quantified by gas chromatography with flame ionization detection. Linear responses were found in the range of 0.03–100 ng mL?1 for naphthalene and 2-methylnaphthalene, and of 0.01–100 ng mL?1 for fluorene and anthracene. The detection limits (at an S/N ratio of 3) range between 3 and 10 pg mL?1. The relative standard deviations (RSDs) for five replicates at three concentration levels (0.05, 5 and 50 ng mL?1) of analytes ranged from 4.9 to 7.4%. The method was applied to the analysis of spiked real water samples. Relative recoveries are between 95.8 and 99.5%, and RSD% are <8.4%.
Graphical abstract A magnetic sorbent was fabricated by polystyrene coated on the magnetic graphene oxide for the extraction and preconcentration of PAHs in water samples prior to their determination by gas chromatography with flame ionization detection.
A method is described for the determination of the activity of alkaline phosphatase (ALP). It is based on the reversible modulation of the fluorescence of WS2 quantum dots (QDs). The fluorescence of the QDs is quenched by Cr(VI) but restored by free ascorbic acid (AA). The detection scheme relies on the fact that ALP hydrolyzes the substrate ascorbic acid 2-phosphate to produce AA, and that enzymatically generated AA can restore the fluorescence of the QDs. The signal (best measured at excitation/emission peak wavelengths of 365/440 nm) increases linearly in the 0.5 to 10 U·L?1 ALP activity range, with a detection limit of 0.2 U·L?1. The method was applied to the determination of ALP activity in human serum samples and demonstrated satisfactory results.
Graphical abstract The fluorescence of chromate-loaded tungsten disulfide quantum dots (QDs) is quenched but restored after reaction with ascorbic acid that is formed by the catalytic action of alkaline phosphatase (ALP) on ascorbic acid 2-phosphate (AAP). The increase in fluorescence can be related to the activity of ALP.
CdSe:Eu nanocrystals were successfully synthesized and characterized by transmission electron microscopy, X-ray powder diffraction, and X-ray photoelectric spectroscopy. The CdSe:Eu nanocrystals showed enhanced green electrochemiluminescence (ECL) intensity when compared to pure CdSe nanocrystals. Further, the nanocrystals were used to design an ECL immunosensor for the detection of carcinoembryonic antigen (CEA) that has a linear response over the 1.0 fg·mL?1 to 100 ng·mL?1 CEA concentration range with a 0.4 fg·mL?1 detection limit. The assay was applied to the determination of CEA in human serum samples.
Graphical abstract Schematic of the assay: GCE-glassy-carbon electrode, Ab- Antibody, BSA- Bovine serum albumin, Ag- Antigen. CdSe:Eu nanocrystals were used to design an ECL immunosensor for the detection of carcinoembryonic antigen.
The authors describe a microsensor for the determination of biochemical oxygen demand. Different from established BOD detection schemes that incorporate a film of immobilized microbes, the sensitive element of this BOD microsensor consists of magnetite-functionalized Bacillus subtilis that can be immobilized and regenerated on an ultramicroelectrode array (UMEA). Modification and regeneration are magnetically controlled. The oxygen consumed is amperometrically quantified by using an UMEA modified with palladium nanoparticles and reduced carboxy graphene. The assay can be performed within 5 min owing to the fast mass transfer of the magnetite-functionalized microbes on the surface of the UMEA. The calibration plot, best acquired at a voltage of -0.4 V vs. Ag/AgCl, is linear in the 2 to 15 mg?L?1 BOD concentration range. A critical comparison with other BOD sensor shows the sensitivity of this sensor to be largely improved. It was successful applied to the determination of BOD in spiked water samples.
Graphical Abstract Schematic presentation of the novel biochemical oxygen demand (BOD) microsensor. The sensitive element can be modified and renewed on ultramicroelectrode array by using a magnet. The response time and the sensitivity of the microsensor are largely improved.
Thin films of La2O3 were deposited onto glass substrates by ultrasonic spray pyrolysis. Their structural and morphological properties were characterized by X-ray diffraction, Fourier transform Raman spectroscopy, scanning electron microscopy, transmission electron microscopy, X-ray photo-electron spectroscopy, Brunauer-Emmett-Teller and optical absorption techniques. The sensor displays superior CO2 gas sensing performance at a low operating temperature of 498 K. The signal change on exposure to 300 ppm of CO2 is about 75%, and the signal only drops to 91% after 30 days of operation.
Graphical abstract Schematic diagram of the CO2 gas sensing mechanism of an interconnected web-like La2O3 nanostructure in presence of 300 ppm of CO2 gas and at an operating temperature of 498 K.
The authors describe a novel assay for the detection of methylated DNA site. Rolling circle amplification and CdSe/ZnS quantum dots with high fluorescence efficiency are applied in this method. The CdSe/ZnS quantum dots act as electron donors, and hemin and oxygen (derived from hydrogen peroxide act as acceptors in photoinduced electron transfer. The assay, best performed at excitation/emission peaks of 450/620 nm, is sensitive and specific. Fluorometric response is linear in the 1 pM to 100 nM DNA concentration range, and the lowest detectable concentration of methylated DNA is 142 fM (S/N =?3). The method is capable of recognizing 0.01% methylated DNA in a mixture of methylated/unmethylated DNA.
Graphical abstract A novel method for methylated sites detection in DNA is established. Rolling circle amplification and photoinduced electron transfer. CdSe/ZnS quantum dots with high fluorescence efficiency act as the electron donor, while G-quadruplex/hemin and hydrogen peroxide derived oxygen act as electron acceptor. It presents a linear response towards 1 pM to 100 nM methylated DNA with a correlation coefficient of 0.9968, and the lowest detectable concentration of methylated DNA was 142 fM, with selectivity significantly superior to other methods.
Hetero-dimeric magnetic nanoparticles of the type Au-Fe3O4 have been synthesised from separately prepared, differently shaped (spheres and cubes), monodisperse nanoparticles. This synthesis was achieved by the following steps: (a) Mono-functionalising each type of nanoparticles with aldehyde functional groups through a solid support approach, where nanoparticle decorated silica nanoparticles were fabricated as an intermediate step; (b) Derivatising the functional faces with complementary functionalities (e.g. amines and carboxylic acids); (c) Dimerising the two types of particles via amide bond formation. The resulting hetero-dimers were characterised by high-resolution TEM, Fourier transform IR spectroscopy and other appropriate methods.
Graphical Abstract Nano-LEGO: Assembling two types of separately prepared nanoparticles into a hetero-dimer is the first step towards complex nano-architectures. This study shows a solid support approach to combine a gold and a magnetite nanocrystal.
Under visible-light irradiation, a cathodic photoelectrochemical (PEC) sensor is presented for highly sensitive determination of Cr(VI) at a potential of ?0.25 V (vs SCE). PbS quantum dots (QDs) were capped with mercaptoacetic acid and assembled on the surface of an indium tin oxide (ITO) electrode via the linker poly(diallyl dimethyl ammonium chloride) providing a photoactive sensor. Cr(VI) accepts the photoelectrons generated by the PbS QDs. This promotes the separation of electron holes and enhances the cathodic photocurrent generated by a 470-nm LED. The sensor has 10 pM detection limit and a linear working range from 0.02 nM to 2 μM of chromate. The method was successfully applied to the determination of Cr(VI) and total chromium in spiked environmental water samples.
Graphical abstract Schematic illustration of the photocurrent enhancement response of ITO/PbS toward chromium(VI). In the presence of Cr(VI) (red line), Cr(VI) accepts the photoelectrons generated by the PbS QDs under 470-nm LED irradiation, resulting in improved photocurrent of ITO/PbS.
