The authors report on a disposable sensor for the differential pulse anodic stripping voltammetric (DPASV) determination of the ions Zn(II), Pb(II) and Cu(II). Simultaneous detection is accomplished by using a screen-printed carbon electrode (SPCE) co-modified with an in-situ plated bismuth (Bi)) film and gold nanoparticles (AuNPs). The synergistic effect of the Bi film, and the large surface and good electrical conductivity of the AuNPs strongly assist in the co-deposition of the three ions. Four well-defined and fully separated anodic stripping peaks, at 540 mV for Zn(II), 50 mV for Pb(II), 140 mV for Bi(III) and 295 mV for Cu(II), all vs. Ag/AgCl, can be seen. The modified SPCE was characterized by scanning electron microscopy, X-ray diffraction, cyclic voltammetry and electrochemical impedance spectroscopy. Under the optimized conditions, the sensor has a good response to these ions. The detection limits (at an S/N ratio of 3) are 50 ng·L?1 for Zn(II), 20 ng·L?1 for Pb(II), and 30 ng·L?1 for Cu(II). The method was applied to the determination of the 3 ions in spiked lake water samples.
Graphical abstract Schematic of screen-printed carbon electrode (SPCE) co-modified with a bismuth film and gold nanoparticles for electrochemical simultaneous determination of Zn(II), Pb(II) and Cu(II) by differential pulse anodic stripping voltammetric (DPASV).
A conducting polymer composite was prepared from nano-sized hydroxyaptite (nHAp) doped into poly(3,4-ethylenedioxythiophene) (PEDOT) and then electrodeposited on a glassy carbon electrode (GCE). The nHAp carries carboxy groups and therefore is negatively charged at moderate pH value. When doped into PEDOT (PEDOT-nHAp), it forms a uniform and stable film that exhibits low electrochemical impedance, a large specific surface, and high activity toward the electrochemical oxidation of nitrite. Under optimized conditions and at a relatively low working potential of 0.78 V (vs. SCE), the modified GCE exhibited a linear amperometric response in the 0.25 μM to 1.05 mM nitrite concentration range, and the limit of detection is as low as 83 nM.
Graphical abstract A highly sensitive nitrite sensor was developed based on conducting polymer poly(3,4-ethylenedioxythiophene) (PEDOT) doped with carboxyl group functionalized hydroxyapatite nanoparticles, which exhibited a large surface area and good conductivity and stability.
The authors describe an electrochemical immunoassay for the core antigen of hepatitis C virus (HCV). The method is based on the use of a screen-printed carbon electrode (SPCE) that was modified with a Nafion@TiO2 nanocomposite and loaded with secondary antibody (Ab2) to entrap Celestine Blue (CB). The material has architecture of the type CB/Ab2/Nafion@TiO2. A nanocomposite consisting of graphene, ionic liquid and fullerene was deposited on the SPCE first, and rhodium nanoparticles (RhNPs) were then deposited on the surface of modified electrode in order to immobilize primary antibody (Ab1). The antigen and CB/Ab2/Nafion@TiO2 were conjugated one by one to form a sandwich-type immunocomplex. The signal was obtained by differential pulse voltammetry whose intensity is related to the concentration of the antigen. The assay, if operated at a working voltage of typically 0.35 V (vs. Ag/AgCl) has a response that is linear in the 0.1 to 250 pg?mL?1 HCV core antigen concentration range, and the limit of detection is as low as 25 fg?mL?1. The assay was applied to the determination of the HCV core antigen in spiked human serum samples. In our perception, the method represents a promising platform for the detection of various antigens if appropriate antibodies are available.
Graphical abstract An electrochemical immunoassay for the core antigen of Hepatitis C virus was studied. A nanocomposite consisting of graphene, ionic liquid and fullerene was deposited on the SPCE and rhodium nanoparticles were deposited on the surface of modified electrode in order to immobilize primary antibody. Nafion@TiO2 was loaded with secondary antibody to entrap Celestine Blue.
A voltammetric sensor is described for the quantitation of propyl gallate (PG). A screen-printed carbon electrode (SPCE) was modified with reduced graphene sheets that were decorated with cobalt diselenide nanoparticles (CoSe2@rGO). The material was hydrothermally prepared and characterized by several spectroscopic techniques. The modified SPCE displays excellent electrocatalytic ability towards PG. Differential pulse voltammetry, with a peak voltage at 0.34 V (vs. Ag/AgCl) has a sensitivity of 12.84 μA·μM?1·cm?2 and a detection limit as low as 16 nM. The method is reproducible, selective, and practical. This method was applied to the determination of PG in spiked meat samples, and the result showed an adequate recovery.
We describe a chemical exfoliation method for the preparation of MoS2 nanosheets. The nanosheets were incorporated into poly(3,4-ethylenedioxythiophene) (PEDOT) by electrodeposition on a glassy carbon electrode (GCE) to form a nanocomposite. The modified GCE is shown to enable simultaneous determination of ascorbic acid (AA), dopamine (DA) and uric acid (UA). Due to the synergistic effect of MoS2 and PEDOT, this electrode displays better properties in terms of electrocatalytic oxidation of AA, DA and UA than pure PEDOT, which is illustrated by cyclic voltammetry and differential pulse voltammetry (DPV). Under optimum conditions and at pH 7.4, the respective sensitivities and best working potentials are as follows: AA: 1.20 A?mM?1?m?2, 30 mV; DA: 36.40 A?mM?1?m?2, 210 mV; UA: 105.17 A?mM?1?m?2, 350 mV. The calculated detection limits for AA, DA and UA are 5.83 μM, 0.52 μM and 0.95 μM, respectively. The modified electrode was applied to the detection of the three species in human urine samples and gave satisfactory results.
Graphical abstract MoS2 nanosheets were prepared by a facile chemical exfoliation method. MoS2 and poly(3,4-ethylenedioxythiophene) nanocomposite modified glassy carbon electrodes were fabricated, which are shown to enable simultaneous determination of ascorbic acid, dopamine and uric acid with high sensitivity and selectivity.
Three-dimensional structures comprising polypyrrole nanowires (PPyNWs) and molecularly imprinted polymer (MIP) were prepared by electropolymerization on the surfaces of a glassy carbon electrode (GCE). The modified GCE possesses both large surface area and good electrocatalytic activity for oxidizing dopamine (DA), and this leads to high sensitivity. The electropolymerized MIP has a large number of accessible surface imprints, and this makes the GCE more selective. Under optimal conditions and at a working voltage of typically 0.23 V (vs. SCE), the calibration plot is linear in the 50 nM to 100 μM DA concentration range, and the limit of detection is 33 nM. The sensor has been successfully applied to the analysis of DA in injections.
Graphical abstract Schematic of a three-dimensional nanocomposite based dopamine sensing platform based on the use of a molecularly imprinted polymer and poly(pyrrole) nanowires. The modified polypyrrole nanowires and molecularly imprinted polymer endowed high electrocatalytic capacity and good selectivity for dopamine recognition, respectively.
A voltammetric analytical assay for the selective quantification of vanillin is described. It is based on the use of a gold nanoparticle-modified screen-printed carbon electrode (SPCE) modified with graphene quantum dots (GQD) in a Nafion matrix. The GQD were synthesized by an acidic thermal method and characterized by UV-Vis, photoluminescence, and FTIR spectroscopy. The modified SPCE displays a strongly enhanced response to vanillin. Linear sweep voltammetry (LSV) and differential pulse voltammetry (DPV) were applied to optimize the methods. The analytical assay has linear responses in the 13 to 660 μM and 0.66 to 33 μM vanillin concentration ranges. The detection limits are 3.9 μM and 0.32 μM when using LSV and DPV, respectively. The analytical assay is selective and stable. It was applied to the determination of vanillin in several food samples with satisfactory results. Recoveries from spiked samples ranged between 92.1 and 113.0%.
Graphical abstract The selective and sensitive quantification of vanillin is carried out by the use of a gold nanoparticle-modified screen-printed carbon electrode modified with graphene quantum dots in a Nafion matrix.
An electrochemical quercetin (QR) sensor is described that is based on the use of magnetic reduced graphene oxide (MrGO) incorporated into a molecularly imprinted polymer (MIP) on the surface of a screen-printed electrode (SPE). The MrGO consists of reduced graphene oxide (rGO), magnetite (Fe3O4) and silver nanoparticles (Ag). The analyte (QR) is electrostatically adsorbed on the surface of the MrGO. Finally, the MIP was deposited via in-situ polymerization. The composite was characterized by X-ray diffraction, Fourier transform infrared spectroscopy and Vibrating sample magnetometry. The morphologies and electrochemical properties of different electrodes were characterized by Field emission scanning electron microscopy, Electrochemical impedance spectroscopy and differential pulse voltammetry. Under optimal conditions, the modified electrode has a linear response in the 20 nM to 250 μM QR concentration range. The limit of detection is 13 nM (at an S/N ratio of 3). The electrode is selective, stable, regenerable and reliable. It was applied to the determination of QR in spiked pharmaceutical samples and gave satisfactory results.
Graphical abstract Schematic presentation of a method for sensing quercetin. It is based on the use of screen printed electrode modified with magnetized reduced graphene oxide and a molecularly imprinted polymer.
A reagentless third generation electrochemical glucose biosensor was fabricated based on wiring the template enzyme glucose oxidase (GOx) with graphene nanoribbons (GN) in order to create direct electron transfer between the co-factor (flavin adenine dinucleotide, FAD) and the electrode. The strategy involved: (i) isolation of the apo-enzyme by separating it from its co-enzyme; (ii) preparation of graphene nanoribbons (GN) by oxidative unzipping of multi-walled carbon nanotubes; (iii) adsorptive immobilization of GNs on the surface of a screen printed carbon electrode (SPCE); (iv) covalent attachment of FAD to the nanoribbons; (v) recombination of the apo-enzyme with the covalently bound FAD to the holoenzyme; and (vi) stabilization of the bio-layer with a thin membrane of Nafion. The biosensor (referred to as GN/FAD/apo-GOx/Nafion/SPCE) is operated at a potential of +0.475 V vs Ag/AgCl/{3 M KCl} in flow-injection mode with an oxygen-free phosphate buffer (pH 7.5) acting as a carrier. The signals are linearly proportional to the concentration of glucose in the range from 50 to 2000 mg?L?1 with a detection limit of 20 mg?L?1. The repeatability (10 measurements, at 1000 mg?L?1 glucose) is ±1.4% and the reproducibility (5 sensors, 1000 mg?L?1 glucose) is ±1.8%. The biosensor was applied to the determination of glucose in human serum.
Graphical abstract Wiring of the apo-enzyme of glucose oxidase (apo-GOx) with graphene nanoribbons (GN) bound to FAD at a screen-printed carbon electrode (SPCE). Cyclic voltammetric and amperometric responses to various glucose concentrations.
The authors report on a ratiometric electrochemical sensor for paracetamol (PR) which was fabricated by successively electropolymerizing a layer of Prussian blue (PB) and a layer of molecularly imprinted polypyrrole (MIP) on the surface of a glassy carbon electrode (GCE). The binding of PR molecules to the MIP has two effects: The first is an increase of the oxidation current for PR at 0.42 V (vs. SCE), and the second is a decrease in the current for PB (at 0.18 V) due to partial blocking of the channels which results in reduced electron transmissivity. Both currents, and in particular their ratio, can serve as analytical information. Under optimized conditions, the sensor displays enhanced sensitivity for PR in the 1.0 nM to 0.1 mM concentration range and a 0.53 nM lower limit of detection. The sensor was applied to the determination of PR in tablets and urines where it gave recoveries in the range between 94.6 and 104.9 %. This dual-signal (ratiometric) detection scheme (using electropolymerized Prussian Blue and analyte-specific MIP) in our perception has a wide scope in that it may be applied to numerous other electroactive species for which specific MIP can be made available.
Graphical Abstract Prussian blue (PB) and molecularly imprinted polymer (MIP) were combined to fabricate an electrochemical sensor for paracetamol (PR) detection. The ratio of both currents, increase of PR current and decrease of PB current, was employed for PR selective detection with enhanced sensitivity.
Stable copper nanoclusters (CuNCs) were prepared by utilizing D-penicillamine as both the stabilizer and reductant. The emission of the CuNCs (with excitation/emission peaks at 390/645 nm) is largely stabilized by coating with poly(sodium-p-styrenesulfonate) (PSS). Cytochrome c (Cyt c) quenches the fluorescence of the PSS-coated CuNCs, and this effect was exploited to design a quenchometric fluorometric assay for Cyt c. If trypsin is added to the loaded CuNCs, it will hydrolyze Cyt c to form peptide fragments, and fluorescence is gradually restored. A highly sensitive and fluorometric turn-off-on assay was constructed for sequential detection of Cyt c and trypsin. The linear ranges for Cyt c and trypsin are from 8.0 nM to 680 nM, and from 0.1 to 6.0 μg mL?1, and the lower detection limits are 0.83 nM and 20 ng mL?1 for Cyt c and trypsin, respectively.
Graphical abstract Schematic illustration of the fluorometric assay for trypsin based on the electron transfer between poly(p-styrenesulfonate)-protected copper nanoclusters (PSS-CuNCs) and cytochrome c (Cyt c).
A simple method is described for the determination of copper(II) ions based on the cathodic electrochemiluminescence (ECL) of lucigenin which is quenched by Cu(II). The blue ECL is best induced at ?0.45 V (vs. Ag/AgCl) at a scan rate of 50 mV·s?1. Under optimum conditions, the calibration plot is linear in the 3.0 to 1000 nM Cu(II) concentration range. The limit of detection is 2.1 nM at a signal-to-noise ratio of 3. Compared to other analytical methods, the one presented here is simple, fast, selective and cost-effective. It has been successfully applied in the analysis of copper ions in spiked tap water samples with recoveries ranging from 93.0% (at 50 nM concentration) to 105.7% (at 150 nM).
Graphical abstract The inhibitory effect of Cu(II) on the cathodic electrochemiluminescence of lucigenin enables determination of Cu(II) with a 2.1 nM detection limit.
A method is described for the synthesis of a nanocomposite containing FeOOH and N-doped carbon nanosheets. The nanocomposite was synthesized by a hydrothermal method using a Fe3O4/chitosan nanocomposite as the precursor. The nanocomposite displays peroxidase-like activity and catalyzes the oxidation of 3,3′,5,5′-tetramethylbenzidine (TMB) by H2O2. This results in the formation of a blue colored product with an absorption maximum at 652 nm in the UV-vis spectra. Based on these findings, colorimetric assays were worked out for both hydrogen peroxide and glucose. The H2O2 assay works in the 5 to 19 μM concentration range, and the limit of detection is 5 nM. The glucose assay works in the 8 μM to 0.8 mM concentration range and has a 0.2 μM detection limit. The method was successfully applied to the determination of glucose in human urine.
Graphical abstract Schematic of the hydrothermal synthesis of a FeOOH/N-doped carbon nanocomposite. It was used to replace peroxidase enzyme for the catalytic oxidation of 3,3′,5,5′-tetramethylbenzidine (TMB) in a visual colorimetric test for glucose in human urine.
The authors describe a disposable electrochemical immunosensor strip for the detection of the Japanese encephalitis virus (JEV). The assay is based on the use of a screen printed carbon electrode (SPCE) modified with carbon nanoparticles (CNPs) that were prepared from starch nanoparticles and deposited on the SPCE working electrode whose surface was functionalized with 3-aminopropyl triethoxysilane. Next, antibody of JEV was immobilized on the surfaces of the CNPs. The analytical performance of immunosensor strip was characterized using cyclic voltammetry (with hexacyanoferrate as the redox probe) and electrochemical impedance spectroscopy. The deposition of CNPs enhances the electron transfer kinetics and current intensity of the SPCE by 63% compared to an unmodified SPCE. Under optimized conditions, the calibration plot is linear within the 5–20 ng·mL?1 JEV concentration range, the limit of detection being 2 ng·mL?1 (at an S/N ratio of 3), and the assay time is 20 min. This immunosensor strip was successfully applied to the detection of JEV in human serum samples. It represents a cost-effective alternative to conventional diagnostic tests for JEV.
Graphical abstract A disposable carbon nanoparticles modified screen printed carbon electrode (SPCE) immunosensor strip for Japanese encephalitis virus (JEV) detection is described. A limit of detection of 2 ng·mL?1 and an assay time of 20 min were achieved.
A voltammetric sensor is described for the determination the antibiotic sulfamethoxazole (SMZ). It is based on the use of a glassy carbon electrode (GCE) modified with a nanocomposite prepared from graphitic carbon nitride and zinc oxide (g-C3N4/ZnO). The nanorod-like ZnO nanostructure were synthesized sonochemically. The g-C3N4/ZnO nanocomposite was then prepared by mixing g-C3N4 with ZnO, followed by ultrasonication. The morphology and structure of the nanocomposite were characterized by X-ray diffraction, Fourier-transform infrared spectroscopy and transmission electron microscopy. Under the optimal conditions, the response of the electrode, typically measured between 0.8 and 0.9 V (vs. Ag/AgCl), increases linearly in the 20 nM to 1.1 mM SMZ concentration range, and the lower detection limit is 6.6 nM. This is better than that of many previously reported sensors for SMZ. The modified electrode is highly selective, well reproducible and maintains its activity for at least 4 weeks. It was applied to the determination of SMZ in spiked human blood serum samples in with satisfactory results.
Graphical abstract Schematic presentation of the voltammetric sensor for sulfamethoxazole. It consists of a glassy carbon electrode modified with a nanocomposite prepared from graphitic carbon nitride (g-C3N4/ZnO) that was supported with zinc oxide nanorods.
We have developed a nonenzymatic sensor for hydrogen peroxide (HP) that is based on a new kind of nanocomposite consisting of silver nanoparticles (AgNPs) electrodeposited on a basic film of a poly(ionic liquid) containing graphene. The nanocomposite was characterized by scanning electron microscopy, energy dispersive X-ray studies, cyclic voltammetry, and chronoamperometry. The AgNPs on the basic composite film provide the electrode with enhanced sensitivity in that the signal obtained for HP is 10-fold improved in the best case. The sensor exhibits good linear response in the 0.1 μM to 2.2 mM HP concentration range, and the detection limit is 0.05 μM (at S/N?=?3). 相似文献
A binary nanocomposite of type copper tungstate and polyaniline (CuWO4@PANI) is described that was obtained by single step polymerization on the surface of a glassy carbon electrode (GCE). The resulting electrode is shown to be a viable tool for voltammetric sensing of quercetin (Qn) in blood, urine and certain food samples. The nanocomposite was characterized by UV-visible absorption spectroscopy, Fourier-transform infrared spectroscopy, thermogravimetric analysis, X-ray diffraction and high-resolution transmission electron microscopy. Differential pulse voltammetry was applied to quantify Qn, typically at the relatively low working potential of 0.15 V (vs. Ag/AgCl). The modified GCE has a wide analytical range (0.001–0.500 μM) and a low detection limit (1.2 nM). The sensor is reproducible, selective and stable. This makes it suitable for determination of Qn in real samples without complicated sample pretreatment.
Graphical abstract Schematic of a copper tungstate and polyaniline nanocomposite modified glassy carbon electrode for voltammetric determination of quercetin in real samples.
A composite material consisting of multiwalled carbon nanotubes and palladium containing particles was synthesized and applied to the preparation of bulk-modified screen-printed carbon electrodes (Pd-MWCNT-SPCE) and surface-modified screen-printed carbon electrodes (Pd-MWCNT/SPCE). They were characterized by cyclic voltammetry and hydrodynamic chronoamperometry in solution of pH 7.5. Both electrodes were then modified with glucose oxidase (GOx) by drop-coating a solution of GOx and Nafion® on their surface. Glucose can be determined via enzymatically formed H2O2. In an alternative approach, gold nanoparticles (5 nm) were incorporated into the biolayer of the electrodes. The resulting electrodes of type GOx/Pd-MWCNT-SPCE and GOx-Au/Pd-MWCNT-SPCE showed acceptable analytical performance at working potentials between ?0.20 V and ?0.50 V in case of hydrodynamic chronoamperometry. Both electrodes can be operated best at a working potential of ?0.40 V vs SCE, with acceptable linearity of the methods in sub mM concentration ranges and with LOQs of 0.14 mM and 0.07 mM for glucose for the GOx/Pd-MWCNT-SPCE and GOx-Au/Pd-MWCNT-SPCE, respectively. Incorporation of gold nanoparticles prolongs the operational lifetime of the electrodes by two weeks. The GOx/Pd-MWCNT-SPCE based method was applied to the determination of glucose in multifloral honey, and the GOx-Au/Pd-MWCNT-SPCE method to the determination of glucose in blood serum. In both cases there was a good agreement with the results obtained by commercially available equipment for determination of glucose.
Graphical abstract Schematic of a screen printed carbon biosensor based on the use of multiwalled carbon nanotubes modified with palladium-containing particles and glucose oxidase. It can be applied to the amperometric determination of glucose in blood serum and multifloral honey
The authors demonstrate the exploitation of reduced graphene oxide (RGO) as a template for immobilizing zeolitic imidazolate framework-8 (ZIF-8) crystals loaded with the electrochemical probe Methylene Blue (MB). The framework was deposited on the surface of RGO in a one-pot process. Transmission electron microscopy, scanning electron microscopy and X-ray diffraction were employed to characterize the nanocomposite. The electrochemical behavior of rutin at a glassy carbon electrode (GCE) modified with the nanocomposite was investigated by cyclic voltammetry and differential pulse voltammetry. The modified GCE displays high electrocatalytic activity toward rutin oxidation at a relatively low working potential (0.4 V vs. Ag/AgCl). Under the optimal conditions, the sensor has an amperometric response that is linear in the 0.1 to 100 μM rutin concentration range, with a 20 nM detection limit (at an S/N ratio of 3). The method was successfully applied to the determination of rutin in tablets and urine samples.
Graphical abstract The zeolitic imidazolate framework ZIF-8 was loaded with Methylene Blue and deposited on the surface of reduced graphene oxide. A glassy carbon electrode was modified with the nanocomposite and then used for the determination of rutin with a 20 nM detection limit and a linear range from 0.1 to 100 μM.
The authors describe a screen-printed and disposable electrode for the nonenzymatic determination of hydrogen peroxide (H2O2). It is based on the controllable synthesis and deposition of silver nanoparticles (AgNPs) of different sizes on a nanocomposite consisting of reduced graphene oxide and cerium (IV) oxide (rGO@CeO2) that was placed on a screen-printed electrode (SPE). X-ray powder diffractometry and Fourier transform infrared spectroscopy were used to characterize the composition of the hybrid nanomaterials. Electrochemical impedance spectroscopy and scanning electron microscopy were employed to study the interfacial properties and morphologies of different electrodes. The sensor was investigated by cyclic voltammetry and chronoamperometry (i-t plots). After optimization, the modified SPE showed a good performance towards the electrocatalytic reduction of H2O2, best at a working potential of ?0.3 V (vs. Ag/AgCl). Features of merit include a broad linear analytical range extending from 0.5 μM to 12 mM, and a limit of detection as low as 0.21 μM (at an S/N ratio of 3). The sensor is simple, quick, stable and reliable. It was applied to the determination of H2O2 in (spiked) contact lens care solutions with good accuracy and recovery.
Graphical abstract An enhanced sensing platform for nonenzymatic hydrogen peroxide (H2O2) based on controllable synthesis of differently sized silver nanoparticles (AgNPs) loaded on reduced graphene oxide and cerium(IV) oxide (rGO@CeO2) nanocomposites to sensitize screen-printed electrode (SPE) was fabricated.
