Improvement of high-voltage cycling behavior of Li(Ni1/3Co1/3Mn1/3)O2 cathodes by Mg, Cr, and Al substitution

To improve the electrochemical properties of Li[Ni_1/3Co_1/3Mn_1/3]O₂ at high charge end voltage (4.6 V), a series of the mixed transition metal compounds, Li(Ni_1/3Co_{1/3 − x} Mn_1/3M _x )O₂ (M = Mg, Cr, Al; x = 0.05), were synthesized via hydroxide coprecipitation method. The effects of doping Mg, Cr, and Al on the structure and the electrochemical performances of Li[Ni_1/3Co_1/3Mn_1/3]O₂ were compared by means of X-ray diffraction (XRD), scanning electron microscopy (SEM), galvanostatic charge–discharge tests, and electrochemical impedance spectroscopy. The XRD results show that all the samples keep layered structures with R3m space group as the Li[Ni_1/3Co_1/3Mn_1/3]O₂. SEM images show that all the compounds have spherical shapes and the Cr-doped sample has the largest particle size. Furthermore, galvanostatic charge–discharge tests confirm that the Cr-doped electrode shows improved cycling performance than the undoped material. The capacity retention of Li(Ni_1/3Co_{1/3 − 0.05}Mn_1/3Cr_0.05)O₂ is 97% during 50 cycles at 2.8∼4.6 V. The improved cycling performance at high voltage can be attributed to the larger particle size and the prevention of charge transfer resistance (R _ct) increase during cycling.     

Influence of Li source on tap density and high rate cycling performance of spherical Li[Ni<Subscript>1/3</Subscript>Co<Subscript>1/3</Subscript>Mn<Subscript>1/3</Subscript>]O<Subscript>2</Subscript> for advanced lithium-ion batteries

Spherical Li[Ni_1/3Co_1/3Mn_1/3]O₂ cathode materials with different microstructure have been prepared by a continuous carbonate co-precipitation method using LiOH⋅H₂O, Li₂CO₃, CH₃COOLi⋅2H₂O and LiNO₃ as lithium source. The effects of Li source on the physical and electrochemical properties of Li[Ni_1/3Co_1/3Mn_1/3]O₂ are investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM) and electrochemical measurements. The results show that the morphology, tap density and high rate cycling performance of Li[Ni_1/3Co_1/3Mn_1/3]O₂ spherical particles are strongly affected by Li source. Among the four Li sources used in this study, LiOH⋅H₂O is beneficial to enhance the tap density of Li[Ni_1/3Co_1/3Mn_1/3]O₂, and the tap density of as-prepared sample reaches 2.32 g cm⁻³. Meanwhile, Li₂CO₃ is preferable when preparing the Li[Ni_1/3Co_1/3Mn_1/3]O₂ with high rate cycling performance, upon extended cycling at 1 and 5C rates, 97.5% and 92% of the initial discharge capacity can be maintained after 100 cycles.     

Synthesis and characterization of LiCo<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>Mn<Subscript>2−<Emphasis Type="Italic">x</Emphasis></Subscript>O<Subscript>4</Subscript> powder by a novel CAM microwave-assisted sol–gel method for Li ion battery

LiMn₂O₄-based spinels are of great interest as positive electrode materials for lithium ion batteries. LiCo _x Mn_2−x O₄ (x = 0.0, 0.1, 0.2, 0.3, and 0.4) spinel phases have been synthesized by novel citric acid-modified microwave-assisted sol–gel method. The structural properties of the synthesized products have been investigated by X-ray powder diffraction and scanning electron microscopy. To improve the recharge capacity of Li/LiCo _x Mn_2−x O₄ cells, the electrochemical features of LiCo _x Mn_2−x O₄ compounds have been evaluated as positive electrode materials. The structural properties of Co-doped oxides are very similar to LiMn₂O₄ electrode. Techniques like cyclic voltammetry, charge–discharge and cycle life are also used to characterize the LiCo _x Mn_2−x O₄ (x = 0.0, 0.1, 0.2, 0.3, and 0.4) electrodes.     

正极材料Li(Ni0.5Mn0.5)1-xMxO2 (M=Ti，Al；x=0，0.02)电化学行为的比较研究

0IntroductionMany efforts have been made to develop newmaterials as an alternative to LiCoO2due to the rela-tively high cost and toxicity of Co.Much attention hasbeen paid to layered structure cathode materials suchas LiMnO2and LiNiO2due to their lower co…     

Synthesis and electrochemical properties of Li-rich Li[Ni<Subscript>0.5</Subscript>Co<Subscript>0.2</Subscript>Mn<Subscript>0.3</Subscript>]O<Subscript>2</Subscript> for pouch-typed cell

Layered transition metal oxide LiNi _x Co _y MnzO₂ cathode materials with different Li amount were successfully synthesized via co-precipitation method. Monodispersed Li[Ni_0.5Co_0.2Mn_0.3]O₂ and Li-rich Li_1.1[Ni_0.5Co_0.2Mn_0.3]O₂ spherical agglomeration consisted of secondary particles, which is favorable for the higher tap-density of materials, can be easily obtained. The pouch-typed cells with obtained materials were assembled to investigate electrochemical performance at level of full-cell. The results show that the assembled pouch-typed full-cells with Li-rich sample present higher capacity, better rate capability and cycle life.     

Thermal behaviour and fragility of Sb<Subscript>2</Subscript>O<Subscript>3</Subscript>-containing zinc borophosphate glasses

Thermal behaviour of the glass series (100-x)[50ZnO-10B₂O₃-40P₂O₅]·xSb₂O₃ (x=0-42 mol%) and (100-y)[60ZnO-10B₂O₃-30P₂O₅]·ySb₂O₃ (y=0-28 mol%) was investigated by DSC and TMA. The addition of Sb₂O₃ results in a decrease of the glass transition temperature and crystallization temperature in both compositional series. All glasses crystallize on heating in the temperature range of 522–632°C. Thermal expansion coefficient of the glasses monotonously increases with increasing Sb₂O₃ content in both series and varies within the range of 6.6–11.7 ppm °C⁻¹. From changes of thermal capacity within the glass transition region it was concluded that with increasing Sb₂O₃ content the ‘fragility’ of the studied glasses increases.     

LiNi<Subscript>0.8</Subscript>Co<Subscript>0.2−x</Subscript>Ti<Subscript>x</Subscript>O<Subscript>2</Subscript> nanoparticles: synthesis,structure, and evaluation of electrochemical properties for lithium ion cell application

Layered Ti-doped lithiated nickel cobaltate, LiNi_0.8Co_{0.2 − x}Ti_xO₂ (where x = 0.01, 0.03, and 0.05) nanopowders were prepared by wet-chemistry technique. The structural properties of synthesized materials were characterized by X-ray diffraction (XRD) and thermo-gravimetric/differential thermal analysis (TG/DTA). The morphological changes brought about by the changes in composition of LiNi_0.8Co_{0.2 − x}Ti_xO₂ particles were examined through surface examination techniques such as scanning electron microscopy (SEM) and transmission electron microscopy (TEM) analyses. Electrochemical studies were carried out using 2016-type coin cell in the voltage range of 3.0–4.5 V (vs carbon) using 1 M LiClO₄ in ethylene carbonate and diethyl carbonate as the electrolyte. Among the various concentrations of Ti-doped lithiated nickel cobaltate materials, C/LiNi_0.8Co_0.17Ti_0.03O₂ cell gives stable charge–discharge features.     

Synthesis of LiNi<Subscript>1/3</Subscript>Co<Subscript>1/3</Subscript>Mn<Subscript>1/3</Subscript>O<Subscript>2</Subscript> nanoparticles by modified Pechini method and their enhanced rate capability

Layered LiNi_1/3Co_1/3Mn_1/3O₂ nanoparticles were prepared by modified Pechini method and used as cathode materials for Li-ion batteries. The pyrolytic behaviors of the foamed precursors were analyzed by use of simultaneous thermogravimetric and differential thermal analysis (TG-DTA). Structure, morphology and electrochemical performance characterization of the samples were investigated by X-ray diffraction (XRD), field emission scanning electron macroscopy(SEM), Brunauer-Emmett-Teller (BET) specific surface area and charge–discharge tests. The results showed that the samples prepared by modified Pechini method caclined at 900 °C for 10 h were indexed to pure LiNi_1/3Co_1/3Mn_1/3O₂ with well hexagonal structure. The particle size was in a range of 100–300 nm. The specific surface area was larger than that of the as-obtained sample by Pechini method. Initial discharge capacity of 163.8 mAh/g in the range 2.8–4.4 V (vs. Li/Li⁺) and at 0.1C for LiNi_1/3Co_1/3Mn_1/3O₂ prepared by modified Pechini method was obtained, higher than that of the sample prepared by Pechini method (143.5 mAh/g). Moreover, the comparison of electrochemical results at different current rates indicated that the sample prepared by modified Pechini method exhibited improved rate capability.     

Sn-doped Li<Subscript>1.2</Subscript>Mn<Subscript>0.54</Subscript>Ni<Subscript>0.13</Subscript>Co<Subscript>0.13</Subscript>O<Subscript>2</Subscript> cathode materials for lithium-ion batteries with enhanced electrochemical performance

Sn-doped Li-rich layered oxides of Li_1.2Mn_0.54-x Ni_0.13Co_0.13Sn _x O₂ have been synthesized via a sol-gel method, and their microstructure and electrochemical performance have been studied. The addition of Sn⁴⁺ ions has no distinct influence on the crystal structure of the materials. After doped with an appropriate amount of Sn⁴⁺, the electrochemical performance of Li_1.2Mn_0.54-x Ni_0.13Co_0.13Sn _x O₂ cathode materials is significantly enhanced. The optimal electrochemical performance is obtained at x = 0.01. The Li_1.2Mn_0.53Ni_0.13Co_0.13Sn_0.01O₂ electrode delivers a high initial discharge capacity of 268.9 mAh g^?1 with an initial coulombic efficiency of 76.5% and a reversible capacity of 199.8 mAh g^?1 at 0.1 C with capacity retention of 75.2% after 100 cycles. In addition, the Li_1.2Mn_0.53Ni_0.13Co_0.13Sn_0.01O₂ electrode exhibits the superior rate capability with discharge capacities of 239.8, 198.6, 164.4, 133.4, and 88.8 mAh g^?1 at 0.2, 0.5, 1, 2, and 5 C, respectively, which are much higher than those of Li_1.2Mn_0.54Ni_0.13Co_0.13O₂ (196.2, 153.5, 117.5, 92.7, and 43.8 mAh g^?1 at 0.2, 0.5, 1, 2, and 5 C, respectively). The substitution of Sn⁴⁺ for Mn⁴⁺ enlarges the Li⁺ diffusion channels due to its larger ionic radius compared to Mn⁴⁺ and enhances the structural stability of Li-rich oxides, leading to the improved electrochemical performance in the Sn-doped Li_1.2Mn_0.54Ni_0.13Co_0.13O₂ cathode materials.     

Effect of lithium boron oxide glass coating on the electrochemical performance of LiNi<Subscript>1/3</Subscript>Co<Subscript>1/3</Subscript>Mn<Subscript>1/3</Subscript>O<Subscript>2</Subscript>

The effect of the lithium boron oxide glass coating on the electrochemical performance of LiNi_1/3Co_1/3Mn_1/3O₂ has been investigated via solution method. The morphology, structure, and electrochemical properties of the bare and coated LiNi_1/3Co_1/3Mn_1/3O₂ are characterized by scanning electron microscopy, X-ray diffraction, electrochemical impedance spectroscopy, and charge–discharge tests. The results showed that the lattice structure of LiNi_1/3Co_1/3Mn_1/3O₂ is not changed after coating. The coating sample shows good high-rate discharge performance (148 mAh g⁻¹ at 5.0 C rate) and cycling stability even at high temperature (with the capacities retention about 99% and 87% at room and elevated temperature after 50 cycles). The Li⁺ diffusion coefficient is also largely improved, while the charge transfer resistance, side reactions within cell, and the erosion of Hydrofluoric Acid all reduced. Consequently, the good electrochemical performances are obtained.     

Improving rate performance of cathode material Li<Subscript>1.2</Subscript>Mn<Subscript>0.54</Subscript>Co<Subscript>0.13</Subscript>Ni<Subscript>0.13</Subscript>O<Subscript>2</Subscript> via niobium doping

As a promising Li-ion battery cathode active material, lithium-rich manganese-based layer-structured oxides suffer from inferior cycle performance and poor rate capability. Herein, Nb-doped Li_1.2Mn_0.54Ni_0.13Co_0.13O₂ is prepared by a sol-gel method, and the effects of Nb doping on its electrochemical performance are investigated. It is concluded that the Nb-doped Li_1.2Mn_0.54Ni_0.13Co_0.13O₂, has a good layered structure along c-axis independent on the amount of Nb dopant and little cationic mixing. Nb doping for Li_1.2Mn_0.54Ni_0.13Co_0.13O₂ has no obvious influence on its morphology. It is found that Nb doping can enhance the electrochemical activity of Li_1.2Mn_0.54Ni_0.13Co_0.13O₂, such as improved rate performance and cycle performance under high rate conditions. Li_1.2Mn_0.54Ni_0.13Co_0.13O₂ doped with 0.015 Nb shows the best cycle performance under the high rate with the capacity maintenance of 95.4% after 100 cycles under 5 C rate, which is higher than that of the undoped one by 10.5%.

Open image in new window

Graphical abstract Rate performance of Li_1.2Mn_0.54-xCo_0.13Ni_0.13Nb _x O₂ materials

     

Interaction between two double-layers for FeCl<Subscript>3</Subscript> and Na<Subscript>3</Subscript>PO<Subscript>4</Subscript> type electrolytes in case the signs of potentials on two plates are opposite

The interaction energies between two double layers for FeCl₃ or Na₃PO₄ type electrolytes at y ₀ > 0 >y _d>—y ₀ were calculated with the aid of 7n parameter methods and the accurate numeral results were given when the dimensionless surface potential of two double layers changes from -20 to +20. When ∣y _d∣ > 5, the absolute value of the interaction energies, ∣V’∣, for FeCl₃ type electrolytes at y ₀= 1 stops to increase. When y ₀> 8, the ∣V’∣ for FeCl₃ type electrolytes at y _d= -1 ceases to change. The influence of y _d on ∣V’∣ for FeCl₃ type electrolytes is more significant than the influence of y ₀. The variation of ∣V’∣ with y _d and y ₀ for Na₃PO₄ type electrolytes is opposite to that for FeCl₃ type electrolytes. The interaction energies between two dissimilar double layers for Na₂SO₄, CaCl₂, NaCl, Na₃PO₄ and FeCl₃ type electrolytes at y ₀= 1 and y _d = -10 are compared and the results indicate that the interaction energies close to each other for FeCl₃ and CaCl₂ type electrolytes and for Na₃PO₄ and Na₂SO₄ type electrolytes, respectively. ∣V’∣ increases with the raises of y ₀ or ∣y _d∣, but decreases with the raises of z ₊ or z _-.     

Nano-composites SnO(VO<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>) as anodes for lithium ion batteries

Nano-composites of SnO(V₂O₃) _x (x = 0, 0.25, and 0.5) and SnO(VO)_0.5 are prepared from SnO and V₂O₃/VO by high-energy ball milling (HEB) and are characterized by X-ray diffraction (XRD), scanning electron microscopy, and high-resolution transmission electron microscopy techniques. Interestingly, SnO and SnO(VO)_0.5 are unstable to HEB and disproportionate to Sn and SnO₂, whereas HEB of SnO(V₂O₃) _x gives rise to SnO₂.VO _x . Galvanostatic cycling of the phases is carried out at 60 mA g⁻¹ (0.12 C) in the voltage range 0.005–0.8 V vs. Li. The nano-SnO(V₂O₃)_0.5 showed a first-charge capacity of 435 (±5) mAh g⁻¹ which stabilized to 380 (±5) mAh g⁻¹ with no noticeable fading in the range of 10–60 cycles. Under similar cycling conditions, nano-SnO (x = 0), nano-SnO(V₂O₃)_0.25, and nano-SnO(VO)_0.5 showed initial reversible capacities between 630 and 390 (±5) mAh g⁻¹. Between 10 and 50 cycles, nano-SnO showed a capacity fade as high as 59%, whereas the above two VO _x -containing composites showed capacity fade ranging from 10% to 28%. In all the nano-composites, the average discharge potential is 0.2–0.3 V and average charge potential is 0.5–0.6 V vs. Li, and the coulombic efficiency is 96–98% after 10 cycles. The observed galvanostatic cycling, cyclic voltammetry, and ex situ XRD data are interpreted in terms of the alloying–de-alloying reaction of Sn in the nano-composite “Sn-VO _x -Li₂O” with VO _x acting as an electronically conducting matrix.     

Mechanisms for the formation of layered A<Subscript>4</Subscript>B<Subscript>3</Subscript>O<Subscript>12</Subscript> compounds from coprecipitated hydroxocarbonate and hydroxide systems

We have established and analyzed the sequences of phase transitions in synthesis of layered compounds in the A_nB_n–1O_3n family ( \textA₃^\textII\textLnB₃^\textV\textO₁₂ {\text{A}}_3^{\text{II}}{\text{LnB}}_3^{\text{V}}{{\text{O}}_{{12}}} (A^II = Ba, Sr, Ln = La, Nd, B^V = Nb, Ta) and La₄Ti₃O₁₂ with n = 4) from coprecipitated hydroxocarbonate and hydroxide systems, including steps involving the formation, solid-phase reaction, or structural rearrangement of intermediates.     

Synthesis and characterization of Mn-, La-Mn- and La-Ca-Mn-citrates as precursors for LaMnO<Subscript>3</Subscript> and La<Subscript>1−x</Subscript>Ca<Subscript>x</Subscript>MnO<Subscript>3</Subscript>

Mn-, LaMn- and LaCaMn-citrates were synthesized at 60–120°C in ethylene glycol medium using chlorides or nitrates as metal sources. Their composition, IR spectra and thermal decomposition were studied. Equimolar La/Mn ratio has been established in the complex, prepared from chloride solution with the same initial composition of the metals. In the isolated three-metallic complex the molar ratio of the metals deviates from the composition in the initial solution. The final products of the heating of Mn- and mixed-metal LaMn-citrates at 1000°C are phase-homogeneous Mn₃O₄ (hausmannite) and LaMnO₃ respectively. Parasitic phase(s) are observed in La_xCa_1−xMn_yO₃, produced from LaCaMn-citrate.     

Synthesis, Crystal Structure, and Magnetic Properties of Quasi-One-Dimensional Oxides Ca3CuMnO6 and Ca3Co1+xMn1−xO6

Synthesis conditions, crystal structures, and magnetic properties of quasi-one-dimensional complex oxides Ca₃CuMnO₆ (space group P-1, z=4, triclinic cell) and Ca₃Co_1+xMn_1−xO₆ with x=0, 0.25, 1.0 (structural type K₄CdCl₆, space group R-3c, z=6) are presented. The crystal structures of Ca₃CoMnO₆ and Ca₃CuMnO₆ were refined using neutron and combined X-ray and neutron diffraction analysis, respectively. The interatomic distances in oxygen polyhedra were found. In contrast to ferromagnetic Ca₃Co₂O₆ (T_c=24 K), manganese-containing phases Ca₃Co_1+xMn_1−xO₆ are characterized by antiferromagnetic interactions with Neel temperatures 18 K (x=0.25) and 13 K (x=0). For Ca₃CuMnO₆T_N was established to be 6 K.     

Mixed conductivity and stability of A-site-deficient Sr(Fe,Ti)O<Subscript>3–δ</Subscript> perovskites

Deficiency in the A sublattice of perovskite-type Sr_{1– y} Fe_0.8Ti_0.2O_3–δ (y=0–0.06) leads to suppression of oxygen-vacancy ordering and to increasing oxygen ionic conductivity, unit cell volume, thermal expansion, and stability in CO₂-containing atmospheres. The total electrical conductivity, predominantly p-type electronic in air, decreases with increasing A-site deficiency at 300–700 K and is essentially independent of the cation vacancy concentration at higher temperatures. Oxygen ion transference numbers for Sr_{1– y} Fe_0.8Ti_0.2O_3–δ in air, estimated from the faradaic efficiency and oxygen permeation data, vary in the range from 0.002 to 0.015 at 1073–1223 K, increasing with temperature. The maximum ionic conductivity was observed for Sr_0.97Fe_0.8Ti_0.2O_3–δ ceramics. In the system Sr_0.97Fe_{1– x} Ti _x O_3–δ (x=0.1–0.6), thermal expansion and electron-hole conductivity both decrease with x. Moderate additions of titanium (up to 20%) in Sr_0.97(Fe,Ti)O_3–δ result in higher ionic conductivity and lower activation energy for ionic transport, owing to disordering in the oxygen sublattice; further doping decreases the ionic conduction. It was shown that time degradation of the oxygen permeability, characteristic of Sr(Fe,Ti)O_3–δ membranes and resulting from partial ordering processes, can be reduced by cycling of the oxygen pressure at the membrane permeate side. Thermal expansion coefficients of Sr_{1– y} Ti_{1– x} Fe _x O_3–δ (x=0.10–0.60, y=0–0.06) in air are in the range (11.7–16.5)×10^–6 K^–1 at 350–750 K and (16.6–31.1)×10^–6 K^–1 at 750–1050 K. Electronic Publication     

Influence of ZnO coating on the structure,morphology and electrochemical performances for LiNi<Subscript>1/3</Subscript>Co<Subscript>1/3</Subscript>Mn<Subscript>1/3</Subscript>O<Subscript>2</Subscript> material

In this paper, ZnO was applied to modify the surface of LiNi_1/3Co_1/3Mn_1/3O₂ cathode material by a simple method. Powder X-ray diffraction (XRD) results show that both of the pristine material and the modified material were well crystallized and closely similar to each other. The crystal parameters of pristine material increased by modified measure. Scan electron microscope (SEM) pictures exhibit that the quasispherical pristine material was modified to the squareness one. Transmission electron microscope (TEM) image clearly elucidates that ZnO (several nanometers to 20 nm) was successful coated on surface of LiNi_1/3Co_1/3Mn_1/3O₂. X-ray photo-electron spectrometry (XPS) is used to characterize the composite of the coating layer on the surface of modified material. Electrochemical performance results present that the ZnO coating layer decrease the initial capacities of LiNi_1/3Co_1/3Mn_1/3O₂ by increasing the surface layer resistances. However, the cycling performance of LiNi_1/3Co_1/3Mn_1/3O₂ was effectively improved by the ZnO coating layer.     

Recent advances in layered LiNi x CoyMn1−x−y O2 cathode materials for lithium ion batteries

Lithium cobalt oxide, LiCoO₂, has been the most widely used cathode material in commercial lithium ion batteries. Nevertheless, cobalt has economic and environmental problems that leave the door open to exploit alternative cathode materials, among which LiNi _x Co_yMn_{1 − x − y} O₂ may have improved performances, such as thermal stability, due to the synergistic effect of the three ions. Recently, intensive effort has been directed towards the development of LiNi _x Co _y Mn_{1 − x − y} O₂ as a possible replacement for LiCoO₂. Recent advances in layered LiNi _x Co_yMn_{1 − x − y} O₂ cathode materials are summarized in this paper. The preparation and the performance are reviewed, and the future promising cathode materials are also prospected.     

Thermal behaviour and properties of Na<Subscript>2</Subscript>O-TiO<Subscript>2</Subscript>-P<Subscript>2</Subscript>O<Subscript>5</Subscript> glasses

Differential scanning calorimetry (DSC) and thermomechanical analysis (TMA) were used to study the thermal behaviour of (50-x)Na₂O-xTiO₂-50P₂O₅ and 45Na₂O-yTiO₂-(55-y)P₂O₅ glasses. The addition of TiO₂ to the starting glasses (x=0 and y=5 mol% TiO₂) resulted in a nonlinear increase of glass transition temperature and dilatation softening temperature, whereas the thermal expansion coefficient decreased. All prepared glasses crystallize under heating within the temperature range of 300–610°C. The contribution of the surface crystallization mechanism over the internal one increases with increasing TiO₂ content. With increasing TiO₂ content the temperature of maximum nucleation rate is also gradually shifted from a value close to the glass transition temperature towards the crystallization temperature. X-ray diffraction measurements showed that the major compounds formed by glass crystallization were NaPO₃, TiP₂O₇ and NaTi₂(PO₄)₃. The chemical durability of the glasses without titanium oxide is very poor, but with the replacement of Na₂O or P₂O₅ by TiO₂, it increases sharply.