MMTCA recognition by molecular imprinting in interpenetrating polymer network hydrogels based on poly(acrylic acid) and poly(vinyl alcohol)

A novel IPN hydrogel designed to recognize MMTCA is prepared by applying the molecular-imprinting method. The IPN is characterized by FT-IR, DSC, and SEM. Langmuir analysis shows that an equal class of adsorption is formed in the hydrogel. The adsorption equilibrium constant and the maximum adsorption capacity are evaluated, and the effect of the pH on MMTCA adsorption is discussed. The selectivity of the imprinted polymer for MMTCA is studied in aqueous solutions of MMTCA/aspirin/riboflavin. The results suggest that the MMTCA-imprinted polymer shows superior selectivity for MMTCA as compared to riboflavin and aspirin. The reproducibility of the imprinted polymer to MMTCA is also studied.     

Pervaporation of alcohol-toluene mixtures through polymer blend membranes of poly(acrylic acid) and poly(vinyl alcohol)

Homogeneous membranes were prepared by blending poly(acrylic acid) with poly(vinyl alcohol). These blend membranes were evaluated for the selective separation of alcohols from toluene by pervaporation. The flux and selectivity of the membranes were determined both as a function of the blend composition and of the feed mixture composition. The results showed that a polymer blending method could be very useful to develop new membranes with improved permselectivity. The pervaporation properties could be optimized by adjusting the blend composition. All the blend membranes tested showed a decrease in flux with increasing poly(vinyl alcohol) content for both methanol—toluene and ethanol—toluene liquid mixtures. The alcohols permeated preferentially through all tested blend membranes, and the selectivity values increased with increasing poly(vinyl alcohol) content. The pervaporation characteristics of the blend membranes were also strongly influenced by the feed mixture composition. The fluxes increased exponentially with increasing alcohol concentration in the feed mixtures, whereas the selectivities decreased for both liquid mixtures.     

一种高电导率PVA聚合物电解质的制备与表征

A type of polymer-in-salt electrolyte composed of poly( vinyl alcohol), KOH and water was prepared by a solution casting method. X-ray diffraction proves that the high concentration of KOH in the electrolyte is in an amorphous state. The ionic conductivities of the PVA-KOH-H2O electrolytes increased as the concentration of KOH increased, and the alkaline electrolyte with PVA/KOH 1/3 (mass ratio) exhibited the highest ionic conductivity of 0. 15 S/cm at room temperature, as measured by electrochemical impedance spectroscopy. The temperature dependence of the conductivity is found to be in agreement with the Arrhenius equation. The potential stability window at the metal/electrolyte interface was of 1.4 V for the nickel electrode determined by cyclic voltammetry.     

High-performance membranes for pervaporation II. Crosslinked poly(vinyl alcohol)–poly(acrylic acid) blends

Dense membranes made by crosslinking of poly(vinyl alcohol) (PVA) with poly(acrylic acid) (PAA) were prepared and tested in pervaporation and differential permeation of water–alcohol mixtures. Instead of a decrease of permeation flux as generally observed with most crosslinking agents, an increase in the permeability was observed with PAA crosslinked membranes at low PAA contents. The permeation flux increases with PAA contents in the polymer with no selectivity reduction for membranes containing less than 15 wt. % PAA. The membranes show good performances to water–2-propanol and water–ethanol mixtures, i.e. high fluxes and high selectivities to pure water. The membranes were stable and highly permeable to water. The enhancement of the permeability of PVA can be explained by a reduced crystallinity and an improved diffusivity due to the presence of PAA.     

Preparation of poly(vinyl alcohol) hydrogels with radiation grafted citric and succinic acid groups

Ternary mixtures of PVA/Citric acid (CA)/water and PVA/Succinic acid (SA)/water were gamma irradiated to various doses in air at ambient temperature. Gelation % vs dose curves were constructed and swelling behavior of gels with maximum conversions was studied. In maximum gelled systems 80% of CA used in the feed composition was retained in the gel structure whereas this was only 20% for SA. The volume of swelling of ionic PVA gels increased from 230% to 530% for PVA/CA systems when pH was increased from 2.6 to 7.5. Less significant increase in swelling was observed for PVA/SA gels, from 250% to 330% in the same pH interval. The incorporation of SA and CA groups onto PVA networks improved remarkably the affinity of these structures for Co²⁺ and Ni²⁺ ion uptake.     

Novel composite polymer electrolytes based on poly(ether-urethane) network polymer and modified montmorillonite

Novel composite solid polymer electrolytes (CSPEs) and composite gel polymer electrolytes (CGPEs) have been prepared. CSPE consists of poly(ether-urethane) network polymer, which is superior to poly(ethylene oxide) in mechanical stability due to its cross-linked structure, modified montmorillonite (MMMT) and LiClO₄, and CGPE with good mechanical strength comprises of the CSPE and LiClO₄–PC (propylene carbonate) solution. The ionic conductivity can be enhanced after the addition of MMMT, and CGPE exhibits ionic conductivity in the order of 10⁻³ S/cm at room temperature. The temperature dependence of the ionic conductivity of the CSPE follows the Vogel–Tamman–Fulcher (VTF) equation. The effects of MMMT on the interactions in these systems and the possible conduction mechanisms are also discussed.     

Preparation of poly(vinyl pivalate) microspheres by dispersion polymerization in an ionic liquid and saponification for the preparation of poly(vinyl alcohol) with high syndiotacticity

We report here a successful free-radical dispersion polymerization of vinyl pivalate (VPi) in an ionic liquid, 1-butyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide ([bmim][TFSI]) using poly(vinyl pyrrolidone) (PVP) as a stabilizer. Morphological analysis by FE-SEM revealed that poly(vinyl pivalate) (PVPi) obtained from dispersion polymerizations were in the form of spherical particles. Micron-sized, PVPi particles with a number-average molecular weight (M_n) of 166,400 g/mol could be obtained using 5% stabilizer (w/w to monomer) at 65 °C for 20 h. The effects of varying concentration of stabilizer, initiator and monomer upon polymer yield, molecular weight, and morphology of PVPi were also investigated. Analogous polymerizations in dimethyl sulfoxide (DMSO) and bulk served as references. In addition, the preparation of poly(vinyl alcohol) (PVA) by saponification of the resultant PVPi was described.     

Effects of ceramic filler in poly(vinyl chloride)/poly(ethyl methacrylate) based polymer blend electrolytes

Effects of nano-ceramic filler titanium oxide (TiO₂) have been investigated on the ionic conductance of polymeric complexes consisting of poly(vinyl chloride) (PVC)/poly(ethyl methacrylate) (PEMA), and lithium perchlorate (LiClO₄). The composite polymer blend electrolytes were prepared by solvent casting technique. The TiO₂ nanofillers were homogeneously dispersed in the polymer electrolyte matrix and exhibited excellent interconnection with PVC/PEMA/PC/LiClO₄ polymer electrolyte. The addition of TiO₂ nanofillers improved the ionic conductivity of the polymer electrolyte to some extent when the content of TiO₂ is 15 wt%. The addition of TiO₂ also enhanced the thermal stability of the electrolyte. The changes in the structural and complex formation properties of the materials are studied by X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR) techniques. The scanning electronmicroscope image of nano-composite polymer electrolyte membrane confirms that the TiO₂ nanoparticles were distributed uniformly in the polymer matrix.     

Electrospinning and characterization of medium-molecular-weight poly(vinyl alcohol)/high-molecular-weight poly(vinyl alcohol)/montmorillonite nanofibers

Submicron fibers of medium-molecular-weight poly(vinyl alcohol) (MMW-PVA), high-molecular-weight poly(vinyl alcohol) (HMW-PVA), and montmorillonite clay (MMT) in aqueous solutions were prepared by electrospinning technique. The effect of HMW-PVA and MMT on the morphology and mechanical properties of the MMW-PVA/HMW-PVA/MMT nanofibers were investigated for the first time. Scanning electron microscopy, viscometer, tensile strength testing machine, thermal gravimetric analyzer (TGA), and transmission electron microscopy (TEM) were utilized to characterize the PVA/MMT nanofibers morphology and properties. The MMW-PVA/HMW-PVA ratios and MMT concentration played important roles in nanofiber's properties. TEM data demonstrated that exfoliated MMT layers were well distributed within nanofibers. It was also found that the mechanical property and thermal stability were increased with HMW-PVA and MMT contents.     

Preparation and Characterization of Interpenetrating Polymer Hydrogels Based on Poly(acrylic acid) and Poly(vinyl alcohol)

Interpenetrating polymer hydrogels (IPHs) of Poly (vinyl alcohol) (PVA) and Poly (acrylic acid) (PAAc) have been prepared by a sequential method: crosslinked PAAc chains were formed in aqueous solution by crosslinking copolymerization of acrylic acid and N, N′-methylenebisacrylamide in the presence of PVA. The application of freezing-thawing cycles (F-T cycles) leads to the formation of a PVA hydrogel within the synthesized PAAc hydrogel. The swelling and the viscoelastic properties of the prepared IPHs were evaluated on the basis of the structural features obtained from solid state ¹³C-NMR spectroscopy.     

Preparation and characterization of poly(acrylic acid)-based nanoparticles

The present investigation describes the synthesis and characterization of nanoparticles based on poly(acrylic acid) (PAA) intramolecularly cross-linked with diamine, 2,2′-(ethylenedioxy)bis(ethylamine), using water-soluble carbodiimide. The aqueous colloid dispersions of nanoparticles were clear or mildly opalescent depending on the ratio of cross-linking, pH of the solution, and the molecular weight of PAA, finding consistent with values of transmittance between 3% and 99%. The structure was determined by nuclear magnetic resonance spectroscopy, and the particle size was identified by dynamic light scattering (DLS) and transmission electron microscopy (TEM) measurements. It was found that particle size depends on the pH, and at a given pH, it was caused by the ratio of cross-linking and the molecular weight of PAA. Particle size measured by TEM varied in the range of 20 and 80 nm. In the swollen state, the average size of the particles measured by DLS was in the range of 35–160 nm.     

Alkaline Zn-air and Al-air cells based on novel solid PVA/PAA polymer electrolyte membranes

High ionic conducting solid polymer electrolyte membranes (SPEM) had been successfully prepared from poly(vinyl alcohol) (PVA) and poly(acrylic acid) (PAA). The solution casting method yielded highly hydrophilic membranes with uniform structure that were suitable for electrochemical applications. The room temperature ionic conductivity of the alkaline PVA/PAA polymer electrolyte membranes was in the range of 0.142–0.301 S cm⁻¹ depending on the composition. The cyclic voltammetry analysis was carried out using Zn|SPEM|Zn and Al|SPEM|Al cells. The analysis results revealed the excellent electrochemical stability of these newly developed alkaline solid PVA/PAA polymer electrolyte membranes. Metal-air fuel cells were also prepared from the alkaline solid PVA/PAA polymer electrolyte membranes. The electrochemical cell performance was evaluated based on Zn-air and Al-air cells at C/10 and C/5 discharge rates. The experimental results exhibited high percent of utilization for metal powders at room temperature. It was up to 90% for Zn-air cell when assembled with PVA:PAA = 10:7.5 polymer electrolyte membrane and discharged at C/10 rate. The power density could be as high as 50 mW cm⁻² at room temperature. However, the cell percent utilization was reduced to 73% with the same composition electrolyte membrane when C/5 discharge rate was tested.     

The synthesis and characterization of monodisperse poly(acrylic acid) and poly(methacrylic acid)

A number of polyacrylic (PAA) and polymethacrylic (PMAA) acids have been synthesized by living anionic polymerization of the monomeric tert-butyl esters followed by subsequent hydrolysis of the corresponding polyesters. The necessary precautions were taken in order to assure good molecular weight control, as well as high yields in the polymerization reactions. The intermediate and final polymers were characterized by gel permeation chromatography and NMR-H¹ spectrometry.     

聚乙烯醇/聚乙烯吡咯烷酮碱性复合膜的制备及其性能

通过在不同浓度KOH溶液中进行掺杂,制备出了聚乙烯醇/聚乙烯吡咯烷酮(PVA/PVP)碱性聚合物电解质膜.详尽考察了膜的组成、微观结构、热稳定性、离子电导率和甲醇吸收率.结果表明,PVA与PVP两者具有较好的相容性,当m(PVA)∶m(PVP)=1∶0.5时,膜断面致密、均匀,未发生大尺度相分离.PVP的混入可以极大提高复合膜的电导率和热稳定性.当m(PVA)∶m(PVP)=1∶1时,复合膜的电导率可达2.01×10-3 S.cm-1.PVA/PVP/KOH膜的甲醇吸收率随温度的升高没有明显变化,100℃时其甲醇吸收率仅为同条件下Nafion 115膜的1/4.这表明该复合膜有望作为一种新型的碱性直接甲醇燃料电池用固体电解质膜且可提高膜的使用温度.     

Preparation of alkaline anion exchange membranes based on functional poly(ether-imide) polymers for potential fuel cell applications

A novel poly(ether-imide)-based alkaline anion exchange membrane with no free base has been prepared and characterized for its ionic conductivity in water, which is a critical metric of its applicability in a liquid-fed direct methanol fuel cell. The poly(ether-imide)-based membranes were prepared by chloromethylation, quaternization and alkalization of commercial poly(ether-imide) and the derivatives were characterized by NMR. The chemical and thermal stabilities were investigated by measuring changes of ionic conductivities when the membranes were placed in various alkaline concentrations and temperatures for 24 h. The membranes were stable at all concentrations of KOH at room temperature, but not at elevated temperatures. The membranes were stable in 1.0 M KOH solution up to 80 °C without losing membrane integrity. The measured conductivity of the formed membrane ranged from 2.28 to 3.51 × 10⁻³ S/cm at room temperature. This preliminary study indicates that functionalized poly(ether-imide) has suitable conductivity suggesting that it can be used as an alkaline anion exchange membrane in fuel cell applications.     

Poly(vinyl alcohol)/cellulose nanocrystal barrier membranes

In this study, barrier membranes were prepared from poly(vinyl alcohol) (PVOH) with different amounts of cellulose nanocrystals (CNXLs) as filler. Poly(acrylic acid) (PAA) was used as a crosslinking agent to provide water resistance to PVOH. The membranes were heat treated at various temperatures to optimize the crosslinking density. Heat treatment at 170 °C for 45 min resulted in membranes with improved water resistance without polymer degradation. Infrared spectroscopy indicated ester bond formation with heat treatment. Mechanical tests showed that membranes with 10% CNXLs/10% PAA/80% PVOH were synergistic and had the highest tensile strength, tensile modulus and toughness of all the membranes studied. Polarized optical microscopy showed agglomeration of CNXLs at filler loadings greater than 10%. Differential thermogravimetric analysis (DTGA) showed a highly synergistic effect with 10% CNXL/10% PAA/80% PVOH and supported the tensile test results.Transport properties were studied, including water vapor transport rate and the transport of trichloroethylene, a representative industrial toxic material. Water vapor transmission indicated that all the membranes allowed moisture to pass. However, moisture transport was reduced by the presence of both CNXLs and PAA crosslinking agent. A standard time lag diffusion test utilizing permeation cups was used to study the chemical barrier properties. The membranes containing ≥10% CNXLs or PAA showed significantly reduced flux compared to the control. The CNXLs were then modified by surface carboxylation in order to better understand the mechanism of transport reduction. While barrier performance improvements were minimal, the chemical modification improved the dispersion of the modified CNXLs which led to improved performance. Of special note was an increase in the initial degradation temperatures of both modified and unmodified systems, with the modified system showing an initial degradation temperature >100 °C higher than the cellulose alone. This may reflect more extensive crosslinking in the modified composite.     

Interpenetrating polymer network (IPN) nanogels based on gelatin and poly(acrylic acid) by inverse miniemulsion technique: synthesis and characterization

Novel interpenetrating polymer network (IPN) nanogels composed of poly(acrylic acid) and gelatin were synthesised by one pot inverse miniemulsion (IME) technique. This is based on the concept of nanoreactor and cross-checked from template polymerization technique. Acrylic acid (AA) monomer stabilized around the gelatin macromolecules in each droplet was polymerized using ammonium persulfate (APS) and tetramethyl ethylene diamine (TEMED) in 1:5 molar ratio and cross-linked with N,N-methylene bisacrylamide (BIS) to form semi-IPN (sIPN) nanogels, which were sequentially cross-linked using glutaraldehyde (Glu) to form IPNs. Span 20, an FDA approved surfactant was employed for the formation of homopolymer, sIPN and IPN nanogels. Formation of stable gelatin-AA droplets were observed at 2% surfactant concentration. Dynamic light scattering (DLS) and scanning electron microscopy (SEM) studies of purified nanogels showed small, spherical IPN nanogels with an average diameter of 255 nm. In contrast, sIPN prepared using the same method gave nanogels of larger size. Fourier-transform infrared (FT-IR) spectroscopy, SEM, DLS, X-ray photoelectron spectroscopy (XPS) and zeta potential studies confirm the interpenetration of the two networks. Leaching of free PAA chains in sIPN upon dialysis against distilled water leads to porous nanogels. The non-uniform surface of IPN nanogels seen in transmission electron microscopy (TEM) images suggests the phase separation of two polymer networks. An increase of N/C ratio from 0.07 to 0.17 (from PAA gel to IPN) and O/C ratio from 0.22 to 0.37 (from gelatin gel to IPN) of the nanogels by XPS measurements showed that both polymer components at the nanogel surface are interpenetrated. These nanogels have tailoring properties in order to use them as high potential drug delivery vehicles for cancer targeting.     

Raman spectral study of solid and dissolved poly(vinyl alcohol) and ethylene-vinyl alcohol copolymer

We have measured the Raman spectra of ethylene-vinyl alcohol copolymer (EVOH) and poly(vinyl alcohol) (PVOH). Spectra of 88% hydrolyzed PVOH were examined from the partially crystalline solid, from PVOH dissolved in both H₂O and D₂O, and from films precipitated from these solutions. The spectrum in H₂O differs from that of the starting material by disappearance of sharp bands having Raman shift values of 1146 and 1093 cm^?1, strengthening of a band near 915 cm^?1, decrease in frequency of bands at 480, 1356, and 1441 cm^?1, and increase in frequency of bands at 369, 413, 1023, 1371, and 2910 cm^?1. The spectrum of the film shows partial reversal of these trends. With D₂O as the solvent, the band shifts are slightly different from those listed above and new bands appear. These changes are indicative of loss of crystallinity, change in stereochemistry, and partial deuteration of hydroxyl during dissolution of this PVOH sample at room temperature. © 1994 John Wiley & Sons, Inc.     

Morphology and structure of highly elastic poly(vinyl alcohol) hydrogel prepared by repeated freezing-and-melting

Morphology and structure of poly(vinyl alcohol) (PVA) hydrogel prepared by the repeated freezing-and-melting method have been investigated by X-ray diffraction, scanning electron microscopy, light-optical microscopy, and simple tension test. The PVA aqueous solution gelled highly by using this method to show rubber-like elasticity, reflecting the gel network in which the amorphous chains are physically cross-linked by the crystallites. The gel morphology was characterized by the porous structure, which was originated from the gelation of continuous PVA-rich solution phase segregated around copious ice crystal phases formed upon freezing. The high gelling ability involved in this method was closely related to the segregation mechanism.     

CE of poly(amidoamine) succinamic acid dendrimers using a poly(vinyl alcohol)-coated capillary

Various generations (G1-G8) of negatively charged poly(amidoamine) (PAMAM) succinamic acid dendrimers (PAMAM-SAH) were analyzed by CE using a poly(vinyl alcohol)-coated capillary. Due to its excellent stability and osmotic flow-shielding effect, highly reproducible migration times were achieved for all generations of dendrimer (e.g., RSD for the migration times of G5 dendrimer was 0.6%). We also observed a reverse trend in migration times for the PAMAM-SAH dendrimers (i.e., higher generations migrated faster than lower generation dendrimers) compared to amine-terminated PAMAM dendrimers reported in the literature. This reversal in migration times was attributed to the difference in counterion binding around these negatively charged dendrimers. This reverse trend allowed a generational separation for lower generation (G1-G3) dendrimers. However, a sufficient resolution for the migration peaks of higher generations (G4-G5) in a mixture could not be achieved. This could be due to their nearly identical charge/mass ratio and dense molecular conformations. In addition, we show that dye-functionalized PAMAM-SAH dendrimers can also be analyzed with high reproducibility using this method.