Peak tailoring concept in gas chromatographic analysis of volatile organic pollutants in the atmosphere

An automated gas chromatographic system aiming at performing unattended analysis of volatile organic compounds (VOCs) was developed in laboratory. To encompass VOCs of a wide range of volatility, two different designs of enrichment and separation methods were adopted and compared with performance in analyzing ozone precursors of C3-C12. In the dual-trap dual-column design, lower boiling species (C3-C6) are enriched and separated by one set of trap and column (porous layer open tubular (PLOT)), whereas the enrichment and separation for the higher boiling species (C6-C12) are performed by the other set (wall-coated open tubular (WCOT)). Undesired peaks also inevitably appear on both chromatograms often causing annoyances. To reduce complexity of both the apparatus and the resulting chromatograms, the heart-cut technique was adopted as a base for developing a system, which only uses one trap and one flame ionization detector for constructing two-dimensional GC with PLOT and DB-1. Methods were developed to allow the auxiliary flow pressure in the heart-cut device to be programmed to create dual effects, which not only can perform regular heart-cut actions but can also temporally hold up species in the precolumn for prescribed time intervals. Because it is characteristic for PLOT chromatograms to have reproducible blank retention time windows, segments of a DB-1 trace are produced by the auxiliary flow program aligning perfectly in time with the gaps of the PLOT trace. Subsequently, the two column flows are merged and channeled into single flame ionization detector to produce a very condensed "tailored" chromatogram which is equivalent to overlaying a PLOT and a DB-1 chromatogram on top of each other, except that no peaks are overlapped. This innovative "peak tailoring" concept based on the heart-cut technique is simple in design, easy to build, and extremely rugged for long-term continuous operation as fewer moving parts are involved, which is beneficial for deploying in remote monitoring stations.     

Simultaneous analysis of atmospheric halocarbons and non-methane hydrocarbons using two-dimensional gas chromatography

A gas chromatographic system was constructed to simultaneously measure ambient non-methane hydrocarbons (NMHCs) and halocarbons, which play significant roles in tropospheric ozone formation and stratospheric ozone loss, respectively. A heart-cut device based on a Deans switch was connected to two capillary columns to cover the full range of NMHCs and halocarbons. Analytes more volatile than C₆ NMHCs and the halocarbon CFC-113 were separated with a PLOT column, while the remaining less volatile compounds were separated with a DB-1 column. Merge-and-split of the flows at the end of the two columns allowed the NMHCs and halocarbons to be observed simultaneously by electron capture detection (ECD) and flame ionization detection (FID). To avoid peak-overlap from the two columns while merging, programmed pressures were incorporated to control the Deans switch. In addition to the advantage of measuring two important classes of compounds in the atmosphere at the same time, this method has the additional benefit of using the homogeneity of atmospheric CFC-113 as an “intrinsic” internal reference. Thus, better data continuity, less consumption of gas standards, and real-time quality control can all be achieved.     

Gas chromatography for in situ analysis of a cometary nucleus III. Multi-capillary column system for the cometary sampling and composition experiment of the Rosetta lander probe

The cometary sampling and composition (COSAC) experiment is one of the principal experiments of the surface lander probe of the European Space Agency Rosetta mission to be launched in January 2003. The instrument is designed for the in situ chemical analysis of a cometary nucleus as the details of the nucleus composition are of primary importance for understanding both the formation of the solar system, and the origin of life on Earth. The COSAC experiment consists of an evaporation/pyrolysis device and two analytical systems: a multi-column gas chromatograph and a high-resolution time-of-flight mass spectrometer which may either be operated alone or in a coupled mode. The gas chromatograph includes five general purpose chromatographic columns and three chiral ones, all mounted in parallel. Taking into account the chemical species potentially present in the cometary nucleus as well as the space constraints, a set of five complementary columns was selected to perform the separation and identification of the compounds present in the cometary nucleus. This set of columns includes a carbon molecular sieve porous-layer open tubular (PLOT) column used for the separation of both the noble and other permanent gases, and the C1-C2 hydrocarbons. A second PLOT column uses a divinylbenzene-ethylene glycol-dimethylacrylate porous polymer as stationary phase for the analysis of a wide range of C1-C2 organic molecules, Two complementary wall-coated open tubular (WCOT) columns with polydimethylsiloxane (PDMS) liquid stationary phases, one containing cyanopropyl-phenylsiloxane and the other diphenylsiloxane groups, are designed to target the same range of organic compounds (C3-C7) which could be representative of the widest range of cometary compounds. A third WCOT column with an apolar stationary phase made of non-substituted PDMS is used for the separation and identification of higher-molecular-mass compounds (up to C10) and aromatic species (monoaromatic and polyaromatic). This paper describes these five general-purpose capillary PLOT and WCOT columns, selected to be used in the COSAC GC system. The analytical capabilities are examined with a special emphasis on the exobiological and planetological implications.     

Evaluation of the separation characteristics of application-specific (volatile organic compounds) open-tubular columns for gas chromatography

The solvation parameter model is used to characterize the separation characteristics of two application-specific open-tubular columns (Rtx-Volatiles and Rtx-VGC) and a general purpose column for the separation of volatile organic compounds (DB-WAXetr) at five equally spaced temperatures over the range 60-140 degrees C. System constant differences and retention factor correlation plots are then used to determine selectivity differences between the above columns and their closest neighbors in a large database of system constants and retention factors for forty-four open-tubular columns. The Rtx-Volatiles column is shown to have separation characteristics predicted for a poly(dimethyldiphenylsiloxane) stationary phase containing about 16% diphenylsiloxane monomer. The Rtx-VGC column has separation properties similar to the poly(cyanopropylphenyldimethylsiloxane) stationary phase containing 14% cyanopropylphenylsiloxane monomer DB-1701 for non-polar and dipolar/polarizable compounds but significantly different characteristics for the separation of hydrogen-bond acids. For all practical purposes the DB-WAXetr column is shown to be selectivity equivalent to poly(ethylene glycol) columns prepared using different chemistries for bonding and immobilizing the stationary phase. Principal component analysis and cluster analysis are then used to classify the system constants for the above columns and a sub-database of eleven open-tubular columns (DB-1, HP-5, DB-VRX, Rtx-20, DB-35, Rtx-50, Rtx-65, DB-1301, DB-1701, DB-200, and DB-624) commonly used for the separation of volatile organic compounds. A rationale basis for column selection based on differences in intermolecular interactions is presented as an aid to method development for the separation of volatile organic compounds.     

Rapid analysis of hydrocarbons and inert gases by a multidimensional gas chromatograph

A combination of a pressure switching system with multiple columns and photoionization detectors makes possible rapid analysis of a mixture of inorganic gases and hydrocarbons. Hydrocarbons are separated by a narrow bore capillary column. An alumina PLOT column is used for the separation of lower molecular weight hydrocarbons, especially C4 isomers, while a combination of a micro-packed column with Porapak N and a PLOT capillary column with Molecular Sieve 5A is used for the fast separation of inorganic gases. A photoionization detector is a powerful additional tool for organic gas analysis.     

Gas chromatographic separation of PF3 substituted group 6 metal carbonyl complexes using serially-coupled capillary columns

The retention of group 6 metal trifluorophosphine carbonyl compounds in serially-coupled gas capillary columns has been studied as a function of different column configurations. For the trifluorophosphine-substituted Mo, W, and Cr carbonyls, as well as the analogous Fe compounds, it was observed that the maximum resolution achievable by the coupled column technique was dependent on the order in which the nonpolar (DB-1) and moderately polar (DB-1701) columns were connected. The optimum configuration was different, however, for each series M(PF₃)_x(CO)_6?x(M = Cr, Mo, or W) or Fe(PF₃)_x(CO)_5?x. It was also observed that the use of coupled columns of dissimilar polarity can, in some cases, actually decrease resolution relative to that obtained by coupled identical columns (i. e. DB-1 + DB-1, or DB-1701 + DB-1701).     

顶空气相色谱-质谱法测定玩具中的10种挥发性有机物

建立了检测玩具中10种挥发性有机物(VOC)残留量的顶空气相色谱-质谱(HS-GC-MS)方法。样品经140 ℃、45 min静态顶空后,通过DB-624色谱柱分离和质谱检测,外标法定量。该方法对于不同VOC的定量限(LOQ)均在0.66 mg/kg以下,线性范围为0.001～2.0 μg,平均回收率在79%～106%之间,相对标准偏差(RSD)在0.4%～5.6%之间。该方法具有准确灵敏、简单快速等特点,将其应用于实际玩具样品的检测取得了良好效果。     

The fabrication of poly (polyethylene glycol diacrylate) monolithic porous layer open tubular (mono‐PLOT) columns and applications in hydrophilic interaction chromatography and capillary gas chromatography for small molecules

The easy shrinkage and swelling of polymer monolithic column when exposed to mobile phase with different polarity is a problem that cannot be ignored. To overcome this drawback, a convenient aqueous two‐phase polymerization approach was used to prepare poly (polyethylene glycol diacrylate, PEGDA) monolithic porous layer open tubular (mono‐PLOT) columns (150 μm). The poly(PEGDA) mono‐PLOT column with homogeneous polymer porous layer was synthesized successfully. A maximum plate number of 41,500 plates per meter for allyl thiourea was obtained under a velocity of 1.8 mm/s. Several kinds of polar molecule were separated on the proposed mono‐PLOT column and a typical hydrophilic interaction retention mechanism was observed. High speed separation of benzoic acids was also carried out, baseline separation of five benzoic acids was successfully achieved within 5 min with a 70 cm mono‐PLOT column at 50°C. Furthermore, the resulting PLOT column was also successfully applied to separate standard analytes of three DNA oxidative damage products and RNA‐modified nucleosides and four chlorophenols. At last, the column could separate alcohols, alkanes, and aromatic isomers via GC. It had more than 20,000 plates per meter for butanol – higher than commercial coatings open tubular columns.     

Separation of intact proteins on porous layer open tubular (PLOT) columns

Porous layer open tubular (PLOT) polystyrene divinylbenzene columns have been used for separating intact proteins with gradient elution. The 10 μm I.D. × 3 m columns were easily coupled to standard liquid chromatography–mass spectrometry (LC–MS) instrumentation with commercially available fittings. Standard proteins separated on PLOT columns appeared as narrow and symmetrical peaks with good resolution. Average peak width increased linearly with gradient time (t_G) from 0.14 to 0.33 min (t_G 20 and 120 min, respectively) using a 3 m column. With shorter columns, peak widths were larger and increased more steeply with gradient time. Theoretical peak capacity (n_c) increased with column length (tested up to 3 m). The n_c increased with t_G until a plateau was reached. The highest peak capacity achieved (n_c = 185) was obtained with a 3 m column, where a plateau was reached with t_G 90 min. The within- and between column retention time repeatabilities were below 0.6% and below 2.5% (relative standard deviation, RSD), respectively. The carry-over following injection of 0.5 ng per protein was less than 1.1%. The retention time dependence on column temperature was investigated in the range 20–50 °C. Proteins in a skimmed milk sample were separated using the method.     

基于微机电系统的高深宽比气相微色谱柱

色谱柱的微型化是实现气相色谱仪微小型化必须要解决的关键问题之一。该文基于微机电系统技术设计制作了一种具有高深宽比微沟道的气相微色谱柱。通过COMSOL软件进行仿真分析,得出气相微色谱柱具有均匀的流速场分布。测试结果表明,该气相微色谱柱成功分离了烷烃类气体混合物及苯系物,其理论塔板数可达14028 plates/m,C7~C8的分离度最高,为10.82。这种气相微色谱柱由于具有体积小、能耗低、分离性能好等优点,可望在微小型气相色谱仪上获得应用。     

Stainless steel capillary columns for high temperature gas chromatography

A layer of elemental silicon has been deposited on the surface of stainless steel tubing by means of chemical vapor deposition (CVD). Two kinds of capillary column were prepared from the deactivated tubing: cross-linked, silanol-terminated polydime-thylsiloxane wall coated open tubular (WCOT) columns and molecular sieve 13X porous layer open tubular (PLOT) columns. Unlike fused silica capillary columns, stainless steel WCOT and PLOT columns can be operated at temperatures in excess of 400°C. High temperature simulated distillation has been performed successfully with a macro bore WCOT column and rapid PNA (paraffin, naphthene, and aromatic) analysis with a multidimensional gas solid chromatographic (GSC) system using PLOT columns.     

西兰花中13种有机含磷农药在不同色谱柱上的色谱保留行为

应用Agilent GC 6890气相色谱仪(附FPD检测器)对13种残留于西兰花中的有机含磷农药(OPP′s)在4种不同极性的毛细管色谱柱(即DB-1、DB-5、DB-1701及DB-35MS)上的保留行为作了研究。结果表明:采用由DB-5及DB-1701串联组成的色谱柱单元,西兰花中13种残留OPP′s可达到有效分离和测定。     

In-situ Preparation of Integrated Polymeric Pora-U PLOT Columns and their Applications in Gas Chromatography

Summary A new method is described to prepare polymeric porous-layer open-tubular (PLOT) columns by using a two-step in-situ polymerization technology. The integrated method involves a straightforward in-situ polymerization of the monomer. By using -(trimethoxysilyl)propyl methacrylate as a bridge, the porous polymer is bonded to the columns inner wall, and this polymer is crosslinked so the whole polymer looks like a single moleculer. The new column avoids the defects of traditional polymer PLOT columns where particles are easily released and swept through the column, causing blockage or a spiking detection signal. The new type of PLOT column is coated with a divinylbenzene and ethylene glycol dimethyl acrylate copolymer and has an increased polarity when compared to a conventional polymer Q-type PLOT column. The retention characteristics of the new column were evaluated and found to be comparable with the commercially available HP PLOT-U column. The inertness of the porous polymer allows the elution of a range of apolar and polar compounds: even most active and polar compounds such as H₂O and H₂S eluted symmetrically. The new column possesses high stability and can withstand temperatures up to 210 °C. With this new type of capillary columns, significantly better mechanical stability, temperature endurance, reproducibility, strong separation power and good inertness are obtained in combination with short analysis times.     

A new look at light hydrocarbon separations on commercial alumina PLOT columns: Column selectivity and separation

Alumina-coated porous layer open tubular (PLOT) columns are widely used for analyses of light hydrocarbons (C₁ to C₆). There is, however, a need for improved selectivity for complex analyses such as the determination of impurities in high purity petrochemical products. Some commercial alumina PLOT columns do not have sufficient selectivity for such analyses. The selectivity of four commercial alumina PLOT columns is evaluated for analyses of propylene and ethylene, and differences in column selectivity discussed. Requirements of column selectivity and retention are presented for several applications including the analysis of refinery gas, transformer oil gas, and fuel gas.     

Evaluation of fused-silica capillary columns for GC/ECD analysis of chlorinated hydrocarbons listed in EPA method 8120

Four mega-bore, one wide-bore, and one narrow-bore fused-silica capillary columns were evaluated for their applicability to the GC/ECD analysis of 22 chlorinated hydrocarbons, some of which are currently targeted by EPA Method 8120. No one column can resolve all 22 compounds investigated here. Four compounds (two pairs) are coeluting on the SPB-35, DB-210, DB-WAX, and DB-519 fused-silica capillary columns, five compounds (two groups) are coeluting on the DB-1301 fused-silica capillary column, and ten compounds (five pairs) are coeluting on the SPB-5 fused-silica capillary column. The analysis time varies between 30 and 50 min. The order of elution of the chlorinated benzenes seems to depend on their boiling points rather than on the polarity of the liquid phase. The retention times of an additional nine chlorinated toluenes, eight chlorinated xylenes, and five chlorinated naphthalenes are also reported. Electron capture detector linearity is reported for the DB-210 fused-silica capillary column. Five brominated compounds were investigated as possible internal standards for Method 8120.     

Devising an adjustable splitter for dual-column gas chromatography

A flow controlled adjustable splitter was configured from a Deans switch and employed in an automated dual column gas chromatographic (GC) system for analyzing mono-aromatic compounds. Volatile organic compounds (VOCs), thermally desorbed from the sorbent trap, were split by the adjustable splitter onto two columns of different phases for separation and then detection by flame ionization detection (FID). Unlike regular splitters in which the split ratio is passively determined by the diameter and/or length of the connecting columns or tubing, the split ratio in our adjustable splitter is controlled by the auxiliary flow in the Deans switch. The auxiliary flow serves as a gas plug on either side of the column for decreasing the sample flow in one transfer line, but increasing the flow in the other. By adjusting the auxiliary flow and therefore the size of the gas plug, the split ratio can be easily varied and favorable to the side of no auxiliary gas. As an illustration, two columns, DB-1 and Cyclodex-B, were employed in this study for separating benzene, toluene, ethylbenzene, xylenes, denoted as BTEX, in particular the structural isomers of o-, m-, p-xylenes. This configuration demonstrates that BTEX cannot be fully separated with either column, but can be deconvoluted by simple algebra if dual columns are used with a splitter. The applicability of the proposed concept was tested by analyzing a gas standard containing BTEX at different split ratios and with various sample sizes, all leading to a constant ratio of m-xylene versus p-xylene.     

二维毛细管柱气相法测定大气中的挥发性烃类

 用二维毛细管柱气相法测定了大气中的挥发性烃类 (VHCs)C3 ～C10 共 5 7种化合物。采用吸附 /两级热解吸预富集样品。采用双柱 (PLOT柱 :5 0m× 0 32mmi d × 8μm ,Al2 O3 /Na2 SO4 ;HP 1柱 :5 0m× 0 2 2mmi d × 0 5 μm ,methylsilicone) /双FID系统进行样品分析。方法的定性稳定性好 ,峰面积的相对标准偏差小于 2 0 % ,用外标法定量 ,线性相关系数r2 分别为 0 9990和 0 9997。分析周期为 48min。通过对江苏常熟生态站 182个农田大气样品中VHCs的含量测定 ,表明方法准确 ,快速 ,可取得满意的结果。     

Two-dimensional strong cation exchange/porous layer open tubular/mass spectrometry for ultratrace proteomic analysis using a 10 microm id poly(styrene- divinylbenzene) porous layer open tubular column with an on-line triphasic trapping column

This study expands the capabilities for ultratrace proteomic analysis of our previous work by incorporating on-line sample desalting using a triphasic (RP/strong cation exchange (SCX)/micro-SPE) trapping column connected to a 3.2 m x 10 microm id poly(styrene-divinylbenzene) (PS-DVB) porous layer open tubular (PLOT) column. To minimize extra sample handling steps, C18 RP packing was incorporated in the capillary tubing upstream of the SCX column for the on-line desalting. For the micro-SPE column, a 50 microm id PS-DVB monolithic column was positioned downstream of the SCX column. High-performance separation was achieved on the PLOT column at a mobile phase flow rate of 20 nL/min. The sensitivity and high resolution capability of the new multidimensional platform was evaluated using an in-gel tryptic digested sample of a cervical cancer (SiHa) cell line. For the injected amount of 1200 cells ( approximately 500 ng), over 2700 peptides covering greater than 850 unique proteins were identified from the triphasic SCX/PLOT/MS analysis of a single SDS gel section (>40 kDa). The 2-D LC/MS platform demonstrated good separation performance, such that more than 85% of the identified peptides were detected from only one salt fraction. In a triplicate analysis of the above >40 kDa gel section, 4497 peptides and 1209 unique proteins were identified when applying stringent filtering criteria, with a false-positive rate of 2.4%. When all three SDS-PAGE gel sections of the lysed SiHa cells were analyzed, 5047 peptides and 1857 unique proteins (false-positive rate 1.8%), including cancer-related proteins such as MAP kinases, were identified.     

Assessment of the selectivity equivalence of DB-608 and DB-624 open-tubular columns for gas chromatography

The solvation parameter model is used to characterize the selectivity of DB-608 and DB-624 open-tubular columns at five equally spaced temperatures over the range 60 to 140 degrees C. The system constants for the DB-608 and DB-624 columns were used as selectivity parameters to search a database of open-tubular columns to identify columns with similar selectivity. The search was refined using the absolute deviation of the system constants and retention factor regression models for varied compounds. For method development it is shown that the selectivity of the poly(cyanopropylphenyldimethylsiloxane) stationary phase containing 6% cyanopropylphenylsiloxane monomer (DB-1301) is equivalent to DB-624 and the poly(dimethyldiphenylsiloxane) stationary phases containing either 50 or 65% diphenylsiloxane monomer (Rtx-50 and Rtx-65) are suitable choices for DB-608.