Effect of solvent in radical polymerization of butadiene 1-carboxylic acid

The radical polymerization and copolymerization of butadiene 1-carboxylic acid (Bu-1-Acid) were studied in a variety of the electron-donor solvents such as dimethylformamide (DMF), tetrahydrofuran (THF), methyl ethyl ketone (MEK), acetonitrile (ACN), and benzene (BZ) using AIBN as an initiator at 50°C. Under these conditions, the polymerization rate of Bu-1-Acid increased in the order, DMF < THF < MEK < ACN < BZ in the various solvents. In copolymerization with styrene [M₂] and acrylonitrile [M₂], the monomer reactivity ratio r₁ increased and r₂ decreased in the same order. Moreover, it was found that Alfrey-Price Q-e value of Bu-1-Acid increased depending on solvent in the order DMF < THF < MEK < ACN < BZ. These variations were correlated to the electron-donating power (Δvcm^?) of the solvents used and are discussed on the basis of the solvation of Bu-1-Acid into the solvent. Also, it was found that the microstructures of these polymers were always trans-1,4 and did not change with the solvent used.     

Effect of pH on radical polymerization of butadiene 1-carboxylic acid in aqueous solutions

Radical polymerization of butadiene 1-carboxylic acid (Bu-1-Acid) was carried out in aqueous solutions at 50°C with ammonium persulfate (APS) as an initiator. Kinetic studies led to the rate equation, R_p = k[APS]^1/2 [Bu-1-Acid]¹ at pH 6.8. The overall activation energy for the polymerization was 16.0 kcal/mole. The polymerization rate R_p of Bu-1-Acid decreased with an increase of pH in the range 2.4–6.8 and increased with an increase of pH in the range 6.8–8.4. Moreover, in the pH range 8.4–13, the rate of polymerization was not affected by the pH of the system. In copolymerization with acrylonitrile, the trends of changes in the monomer reactivity ratios r₁, r₂ and Q-e values caused by changes in pH were similar to trends found in homopolymerization described above. In addition, it was observed that the resultant polymer was extended in alkaline solution and contracted in acidic solution.     

Radical-initiated homo- and copolymerizations of methacryloyl fluoride

The kinetics of methacryloyl fluoride (MAF) homopolymerization was investigated in methyl ethyl ketone (MEK) with azobis(isobutyronitrile) as initiator. The rate of polymerization (R_p) followed the expression R_p = k[AIBN]^0.55[MAF]^1.18. The overall activation energy was calculated as 74.4 kJ/mol. The relative reactivity ratios of MAF(M₂) copolymerization with styrene (r₁ = 0.083, r₂ = 0.14), and methyl methacrylate (r₁ = 0.48, r₂ = 0.81) in methyl ethyl ketone were obtained. Application of the Q–e scheme (in styrene copolymerization) led to Q = 2.22 and e = 1.31. The glass transition temperature (T_g) of poly(MAF) was 90°C by thermomechanical analysis. Thermogravimetry of poly(MAF) showed a 10% weight loss of 228°C in air.     

Silyl enol ethers as monomer. III. Radical polymerization and copolymerizations of 2-trimethylsilyloxy-1,3-butadiene and desilylation of the resulting polymers

2-Trimethylsilyloxy-1,3-butadiene (TMSBD), the silyl enol ether of methyl vinyl ketone, was homopolymerized with a radical initiator to afford polymers with a molecular weight of ca. 10⁴. Radical copolymerizations of TMSBD with styrene (ST) and acrylonitrile (AN) in bulk or dioxane at 60°C gave the following monomer reactivity ratios: r₁ = 0.64 and r₂ = 1.20 for the ST (M₁)–TMSBD (M₂) system and r₁ = 0.036 and r₂ = 0.065 for the AN (M₁)–TMSBD (M₂) system. The Q and e values of TMSBD determined from the reactivity ratios for the former copolymerization system were 2.34 and ?1.31, respectively. The resulting polymer and copolymers were readily desilylated with hydrochloric acid or tetrabutylammonium fluoride as catalyst to yield analogous polymers having carbonyl groups in the polymer chains.     

Silyl enol ethers as monomer. I. Radical copolymerizability of α-trimethylsilyloxystyrene

α-Trimethylsilyloxystyrene (TMSST), the silyl enol ether of acetophenone, was not homopolymerized either by a radical or a cationic initiator. Radical copolymerization of TMSST with styrene (ST) and acrylonitrile (AN) in bulk and the terpolymerization of TMSST, ST, and maleic anhydride (MA) in dioxane were studied at 60°C and the polymerization parameters of TMSST were estimated. The rate of copolymerization decreased with increased amounts of TMSST for both systems. Monomer reactivity ratios were found as follows: r₁ = 1.48 and r₂ = 0 for the ST (M₁)–TMSST (M₂) system and r₁ = 0.050 and r₂ = 0 for the AN (M₁)–TMSST (M₂) system. The terpolymerization of ST (M₁), TMSST (M₂), and MA (M₃) gave a terpolymer containing ca. 50 mol % of MA units with a varying ratio of TMSST to ST units and the ratio of rate constants of propagation, k₃₂/k₃₁, was found to be 0.39. Q and e values of TMSST were determined using the values shown above to be 0.88 and ?1.13, respectively. Attempted desilylation by an acid catalyst for the copolymer of TMSST with ST afforded polystyrene partially substituted with hydroxyl groups at the α-position.     

Emulsion polymerization and copolymerization of vinyl benzoate

Emulsion polymerization of vinyl benzoate and its copolymerization with vinyl acetate or styrene are described. The effect of the potassium persulfate initiator, and the sodium lauryl sulfate emulsifier concentration on the rate of vinyl benzote homopolymerization and the molecular weight of the polymers was determined. In copolymerization with vinyl benzoate, both comonomers, vinyl acetate and styrene, decrease the initial polymerization rate. With increasing amounts of styrene in the comonomer mixture the polymerization rate increases but with vinyl acetate an opposite effect is observed. Reactivity ratios of copolymerizations were determined. For the vinyl benzoate [M₁]-styrene [M₂] comonomer system a r₁ = 0.03 and a r₂ = 29.58 and for vinyl benzoate [M₁]-vinyl acetate [M₂], a r₁ = 1.93 and a r₂ = 0.20 was obtained. From the vinyl benzoate-styrene reactivity ratios the Qe parameters were calculated.     

Radical-initiated homo- and copolymerization of cyanomethyl methacrylate

The kinetics of cyanomethyl methacrylate (CyMA) homopolymerization was investigated in acetonitrile with azobisisobutyronitrile as initiator. The rate of polymerization R_p was expressed by R_p = k[AIBN]^0.49[CyMA]^1.2 and the overall activation energy was calculated as 72.3 kJ/mol. Kinetic constants for CyMA polymerization were obtained as follows: k_p/k = 0.10 L^1/2s^?1/2; 2fk_d = 1.57 × 10^?5s^?. The relative reactivity ratios of CyMA(M₂) copolymerization with styrene (r₁ = 0.15, r₂ = 0.29) and methyl methacrylate (r₁ = 0.43, r₂ = 0.75) in acetonitrile were obtained. Applying the Q-e scheme (in styrene copolymerization) led to Q = 1.64 and e = 0.98. The glass transition temperature T_g of poly(CyMA) was observed to be 91°C by thermomechanical analysis. Thermogravimetry of poly(CyMA) showed a 10% weight loss at 265°C in air.     

Radical and cationic polymerizations of 3‐ethyl‐3‐methacryloyloxymethyloxetane

3‐Ethyl‐3‐methacryloyloxymethyloxetane (EMO) was easily polymerized by dimethyl 2,2′‐azobisisobutyrate (MAIB) as the radical initiator through the opening of the vinyl group. The initial polymerization rate (R_p) at 50 °C in benzene was given by R_p = k[MAIB]^0.55 [EMO]^1.2. The overall activation energy of the polymerization was estimated to be 87 kJ/mol. The number‐average molecular weight (M?_n) of the resulting poly(EMO)s was in the range of 1–3.3 × 10⁵. The polymerization system was found to involve electron spin resonance (ESR) observable propagating poly(EMO) radicals under practical polymerization conditions. ESR‐determined rate constants of propagation (k_p) and termination (k_t) at 60 °C are 120 and 2.41 × 10⁵ L/mol s, respectively—much lower than those of the usual methacrylate esters such as methyl methacrylate and glycidyl methacrylate. The radical copolymerization of EMO (M₁) with styrene (M₂) at 60 °C gave the following copolymerization parameters: r₁ = 0.53, r₂ = 0.43, Q₁ = 0.87, and e₁ = +0.42. EMO was also observed to be polymerized by BF₃OEt₂ as the cationic initiator through the opening of the oxetane ring. The M?_n of the resulting polymer was in the range of 650–3100. The cationic polymerization of radically formed poly(EMO) provided a crosslinked polymer showing distinguishably different thermal behaviors from those of the radical and cationic poly(EMO)s. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 1269–1279, 2001     

Effect of Solvent on the Radical Copolymerizability of Styrene with Acrylonitrile

Radical copolymerization of styrene (St, M₁) with acrylonitrile (AN, M₂) has been carried out using azobisisobutylonitrile as an initiator in benzene, dimethylsulfoxide, acetonitrile, and ethanol at 60 and 80°C. Good linear correlationships were obtained by plotting the values of log r₁, log r₂, Q₂, and e₂ against those of vC[dbnd]N and vC[dbnd]C determined in the solvents: the increase in the interaction between AN and the solvent was found to decrease the values of log r₁ and e₂ but to increase those of log r₂ and Q₂. The results are discussed in terms of the solvation both in the ground state and in the transition state.     

Kinetic study of the radical polymerization behavior of N‐(1‐phenylethylaminocarbonyl)methacrylamide

Polymerization of N‐(1‐phenylethylaminocarbonyl)methacrylamide (PEACMA) with dimethyl 2,2′‐azobisisobutyrate (MAIB) was kinetically studied in dimethyl sulfoxide (DMSO). The overall activation energy of the polymerization was estimated to be 84 kJ/mol. The initial polymerization rate (R_p) is given by R_p = k[MAIB]^0.6[PEACMA]^0.9 at 60 °C, being similar to that of the conventional radical polymerization. The polymerization system involved electron spin resonance (ESR) spectroscopically observable propagating poly(PEACMA) radical under the actual polymerization conditions. ESR‐determined rate constants of propagation and termination were 140 L/mol s and 3.4 × 10⁴ L/mol s at 60 °C, respectively. The addition of LiCl accelerated the polymerization in N,N‐dimethylformamide but did not in DMSO. The copolymerization of PEACMA(M₁) and styrene(M₂) with MAIB in DMSO at 60 °C gave the following copolymerization parameters; r₁ = 0.20, r₂ = 0.51, Q₁ = 0.59, and e₁ = +0.70. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 2013–2020, 2005     

Polymerization of 1,3‐dienes with functional groups. II. Free‐radical polymerization of N‐(2‐methylene‐3‐butenoyl)piperidine

The free‐radical homopolymerization and copolymerization behavior of N‐(2‐methylene‐3‐butenoyl)piperidine was investigated. When the monomer was heated in bulk at 60 °C for 25 h without an initiator, about 30% of the monomer was consumed by the thermal polymerization and the Diels–Alder reaction. No such side reaction was observed when the polymerization was carried out in a benzene solution with 1 mol % 2,2′‐azobisisobutylonitrile (AIBN) as an initiator. The polymerization rate equation was found to be R_p ∝ [AIBN]^0.507[M]^1.04, and the overall activation energy of polymerization was calculated to be 89.5 kJ/mol. The microstructure of the resulting polymer was exclusively a 1,4‐structure that included both 1,4‐E and 1,4‐Z configurations. The copolymerizations of this monomer with styrene and/or chloroprene as comonomers were carried out in benzene solutions at 60 °C with AIBN as an initiator. In the copolymerization with styrene, the monomer reactivity ratios were r₁ = 6.10 and r₂ = 0.03, and the Q and e values were calculated to be 10.8 and 0.45, respectively. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1545–1552, 2003     

Polymerization of N-acryloyl pyrrolidone and synthesis of graft copolymer by using the mechanism of initiation of anionic ring-opening polymerization

N-acryloyl pyrrolidone (NAP) was synthesized by reaction of pyrrolidone with acryloyl chloride. First, the polymerization of NAP and copolymerization of NAP with styrene (St) were carried out at 60°C, using 2,2′-azobisisobutyronitrile (AIBN) as an initiator. Kinetic studies showed that the rate of polymerization (R_p) could be expressed by R_p = K [AIBN]^0.5 [NAP]^1.0. The reactivity of NAP was found to be larger than that of N-methacryloyl pyrrolidone. The overall activation energy was calculated to be 24.3 kcal mole^?1. The following monomer reactivity ratio and Q and e values were obtained. NAP(M₁)—St(M₂): r₁ = 1.50, r₂ = 0.35, Q₁ = 0.42, and e₁ = 1.60. Second, graft copolymers were synthesized by reacting pyrrolidone, in the presence of a catalytic amount of its potassium salt, with poly(NAP-co-St).     

Polymerization of 1,3‐dienes with functional groups. III. Free‐radical polymerization of N,N‐diethyl‐2‐methylene‐3‐butenamide

Free‐radical homo‐ and copolymerization behavior of N,N‐diethyl‐2‐methylene‐3‐butenamide (DEA) was investigated. When the monomer was heated in bulk at 60 °C for 25 h without initiator, rubbery, solid gel was formed by the thermal polymerization. No such reaction was observed when the polymerization was carried out in 2 mol/L of benzene solution with with 1 mol % of azobisisobutyronitrile (AIBN) as an initiator. The polymerization rate (R_p) equation was R_p ∝ [DEA]^1.1[AIBN]^0.51, and the overall activation energy of polymerization was calculated 84.1 kJ/mol. The microstructure of the resulting polymer was exclusively a 1,4‐structure where both 1,4‐E and 1,4‐Z structures were included. From the product analysis of the telomerization with tert‐butylmercaptan as a telogen, the modes of monomer addition were estimated to be both 1,4‐ and 4,1‐addition. The copolymerizations of this monomer with styrene and/or chloroprene as comonomers were also carried out in benzene solution at 60 °C. In the copolymerization with styrene, the monomer reactivity ratios obtained were r₁ = 5.83 and r₂ = 0.05, and the Q and e values were Q = 8.4 and e = 0.33, respectively. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 999–1007, 2004     

Copolymerization of trialkylvinylgermane

The polymerization of trimethylvinylgermane (TMGeV) with the use of γ-ray, radical, and ionic initiator was attempted, but homopolymer was not obtained. This monomer did not undergo polymerization by itself, but polymerized with high concentration of n-BuLi. Copolymerization of TMGeV with styrene (St) and methyl methacrylate (MMA) was carried out by using radical initiator. From the results obtained by the copolymerization, monomer reactivity ratios and Q–e values were obtained as follows: for the system St(M₁)–TMGeV (M₂), r₁ = 24.4, r₂ = 0.009, Q₂, = 0.0049, e₂ = 0.43; for the system MMA (M₁)–TMGeV (M₂), r₁ = 19.98, r₂ = 0.05; Q₂ = 0.037, e₂ = 0.43., The polymerizability of TMGeV is discussed on the basis of the Q and e values obtained.     

Copolymerization of 4-cyclopentene-1,3-dione with p-chlorostyrene and vinylidene chloride

The copolymerization of 4-cyclopentene-1,3-dione (M₂) with p-chlorostyrene and vinylidene chloride is reported. The copolymers were prepared in sealed tubes under nitrogen with azobisisobutyronitrile initiator. Infrared absorption bands at 1580 cm.^?1 revealed the presence of a highly enolic β-diketone and indicated that copolymerization had occurred. The copolymer compositions were determined from the chlorine analyses and the reactivity ratios were evaluated. The copolymerization with p-chlorostyrene (M₁) was highly alternating and provided the reactivity ratios r₁ = 0.32 ± 0.06, r₂ = 0.02 ± 0.01. Copolymerization with vinylidene chloride (M₁) afforded the reactivity ratios r₁ = 2.4 ± 0.6, r₂ = 0.15 ± 0.05. The Q and e values for the dione (Q = 0.13, e = 1.37), as evaluated from the results of the vinylidene chloride case, agree closely with the previously reported results of copolymerization with methyl methacrylate and acrylonitrile and confirm the general low reactivity of 4-cyclopentene-1,3-dione in nonalternating systems.     

Radical-initiated homo- and copolymerization of α-methylene-γ-butyrolactone

The kinetics of α-methylene-γ-butyrolactone (α-MBL) homopolymerization was investigated in N,N-dimethylformamide (DMF) with azobis(isobutyronitrile) as initiator. The rate of polymerization (R_p) was expresed by R_p = k[AIBN]^0.54[α-MBL]^1.1 and the overall activation energy was calculated as 76.1 kJ/mol. Kinetic constants for α-MBL polymerization were obtained as follows: k_p/k_t^1/2 = 0.161 L^1/2 mol^?1/2·s^?1/2; 2fk_d = 2.18 × 10^?5 s^?1. The relative reactivity ratios of α-MBL(M₂) copolymerization with styrene (r₁ = 0.14, r₂ = 0.87) were obtained. Applying the Q–e scheme led to Q = 2.2 and e = 0.65. These Q and e values for α-MBL are higher than those for MMA     

Radical polymerization behavior of trimethoxyvinylsilane

Trimethoxyvinylsilane (TMVS) was quantitatively polymerized at 130 °C in bulk, using dicumyl peroxide (DCPO) as initiator. The polymerization of TMVS with DCPO was kinetically studied in dioxane by Fourier transform near‐infrared spectroscopy. The overall activation energy of the bulk polymerization was estimated to be 112 kJ/mol. The initial polymerization rate (R_p) was expressed by R_p = k[DCPO]^0.6[TMVS]^1.0 at 120 °C, being closely similar to that of the conventional radical polymerization involving bimolecular termination. The polymerization system involved electron spin resonance (ESR) spectroscopically observable polymer radicals under the actual polymerization conditions. ESR‐determined apparent rate constants of propagation and termination were 13 L/mol s and 3.1 × 10⁴ L/mol s at 120 °C, respectively. The molecular weight of the resulting poly(TMVS)s was low (M_n = 2.0–4.4 × 10³), because of the high chain transfer constant (C_mtr = 4.2 × 10^?2 at 120 °C) to the monomer. The bulk copolymerization of TMVS (M₁) and vinyl acetate (M₂) at 120 °C gave the following copolymerization parameters: r_l = 1.4, r₂ = 0.24, Q₁ = 0.084, and e₁ = +0.80. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 5864–5871, 2005     

Radical polymerization of ortho-(1,3-dioxolan-2-yl)phenyl ethyl fumarate involving intramolecular hydrogen abstraction and ring opening of cyclic acetal

The polymerization of o-(1,3-dioxolan-2-yl)phenyl ethyl fumarate (DOPEF) initiated with dimethyl 2,2′-azobisiso-butyrate (MAIB) was studied kinetically in benzene. The polymerization rate (R_p) at 60°C was given by R_p = k [MAIB]^0.76 [DOPEF]^0.71. The overall activation energy of polymerization was calculated to be 98.3 kJ/mol. The number-average molecular weight of resulting poly(DOPEF) was in the range of 1000–3100. ¹H- and ¹³C-NMR spectra of resulting polymers revealed that the radical polymerization of DOPEF proceeds in a complicated manner involving vinyl addition, intramolecular hydrogen abstraction, and further ring opening of the cyclic acetal at higher temperatures. From the copolymerization of DOPEF (M₁) and styrene (St) (M₂) at 60°C, the monomer reactivity ratios were obtained to be r₁ = 0.02 and r₂ = 0.20, the values of which are similar to those of the copolymerization of ethyl o-formylphenyl fumarate and St. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 563–572, 1998     

Kinetic study on the radical polymerization of 2‐methacryloyloxyethyl phosphorylcholine

Polymerization of 2‐methacryloyloxyethyl phosphorylcholine (MPC) was kinetically investigated in ethanol using dimethyl 2,2′‐azobisisobutyrate (MAIB) as initiator. The overall activation energy of the homogeneous polymerization was calculated to be 71 kJ/mol. The polymerization rate (R_p) was expressed by R_p = k[MAIB]^0.54±0.05 [MPC]^1.8±0.1. The higher dependence of R_p on the monomer concentration comes from acceleration of propagation due to monomer aggregation and also from retardation of termination due to viscosity effect of the MPC monomer. Rate constants of propagation (k_p) and termination (k_t) of MPC were estimated by means of ESR to be k_p = 180 L/mol · s and k_t = 2.8 × 10⁴ L/mol · s at 60 °C, respectively. Because of much slower termination, R_p of MPC in ethanol was found at 60 °C to be 8 times that of methyl methacrylate (MMA) in benzene, though the different solvents were used for MPC and MMA. Polymerization of MPC with MAIB in ethanol was accelerated by the presence of water and retarded by the presence of benzene or acetonitrile. Poly(MPC) showed a peculiar solubility behavior; although poly(MPC) was highly soluble in ethanol and in water, it was insoluble in aqueous ethanol of water content of 7.4–39.8 vol %. The radical copolymerization of MPC (M₁) and styrene (St) (M₂) in ethanol at 50 °C gave the following copolymerization parameters similar to those of the copolymerization of MMA and St; r₁ = 0.39, r₂ = 0.46, Q₁ = 0.76, and e₁ = +0.51. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 509–515, 2000     

Quantitative Determination of the Contribution of Charge‐Transfer Complex in the Microemulsion Copolymerization of N‐Butyl Maleimide and Styrene

By using sodium dodecyl sulfate (SDS) and pentanol (PTL) as emulsifiers, the oil‐in‐water microemulsion containing N‐butyl maleimide (NBMI, M₁) and styrene (St, M₂) was prepared. The microemulsion copolymerization using potassium persulfate (KPS) as an initiator was investigated. On the basis of kinetic model proposed by SHAN Guo‐Rong, the reactivity ratios of free monomers and the charge‐transfer complex (CTC) in the copolymerization were found to be r₁₂ = 0.0420, r₂₁ = 0.0644, r_1C = 0.00576 and r_2C = 0.00785, respectively. A kinetic treatment based on this model was used to quantitatively estimate the contribution of CTC to the total copolymerization rate in the NBMI/St copolymerization. It was about 17.0–20.0% for a wide range of monomer feed ratios.