脂肪族水性聚氨酯的力学性能研究

考察了软段的种类、分子量大小、混合软段的组成对产物力学性能的影响作用。同时还研究了二羟甲基丙酸(DMPA)用量以及中和剂的影响作用．实验结果表明。软段结构对脂肪族水性聚氨酯成膜的力学性能影响很大，聚酯型产物具有较高的模量和拉伸强度。聚醚型产物则具有较高的伸长率．混合软段对产物力学性能的影响较为复杂，随着软段中聚醚含量的升高，产物的硬度和模量均大幅度下降，但拉伸强度和伸长率的变化并不是一个线性关系．产物的模量随软段分子量的提高而降低，但伸长率和拉伸强度却有所提高．当DMPA用量较高时。产物的模量和拉伸强度均较高：当DMPA用量较低时，产物则具有较高的伸长率．中和剂的种类对产物力学性能的影响明显，当以NaOH为中和剂时，产物具有较高的硬度、模量、拉伸强度：以三乙胺为中和剂时，产物具有较高的伸长率．     

单组分聚氨酯清漆的制备与性能研究

不同的聚碳酸酯二元醇、聚四亚甲基醚二醇(PTMG)与二苯甲烷二异氰酸酯(MDI)、小分子二元醇反应,制得聚醚、聚碳酸酯型聚氨酯清漆。通过红外光谱分析结合其机械力学性能、耐水性等的测试结果,探讨聚碳酸酯型聚氨酯清漆的结构对形态和性能的影响。结果表明：随着硬段含量的增加,树脂涂膜的微相分离程度增加,机械性能提高;组分摩尔比例相同时,软段分子量的降低有利于提高树脂的软硬段相容性,增加树脂涂膜的物理机械性能;组分摩尔比例相同时聚酯型聚氨酯树脂的微相分离程度低于聚醚型聚氨酯树脂;MDI基溶剂型聚氨酯树脂的物理机械性能较好。     

聚氨酯弹性体相分离程度的研究

热塑型聚氨酯弹性体(TPUE)的动态力学性能和热性能研究已有许多报导,但多集中于弹性体的链结构及其组成等方面,本文则侧重于研究聚醚氨酯(ET)和聚酯氨酯的相分离过程及其程度,考察硬段含量(W_h)和软段分子量(M_(n·3)等因素对微相结构的影响。     

微相分离及链结构对聚酯-聚醚嵌段共聚物分子运动的影响

本文首先研究了成型方法和热处理对聚对苯二甲酸乙二酯与聚氧四亚甲基嵌段共聚物动态力学温度谱的影响,结合应力-应变曲线讨论了微相分离与力学性能的关系。其次,比较了三种不同链结构的聚酯-聚醚嵌段共聚物在不同温控程序下的动态力学温度谱,讨论了链结构对软链段结晶的影响。最后观察了聚氨酯-聚醚嵌段共聚物双重玻璃化转变现象并作了解释。     

聚醚聚氨酯-聚醚聚酰亚胺合金相结构的研究

通过不同分子量的对－氨基苯甲酸酯封端的聚（四次亚甲基）醚和均苯甲甲酸二酐反应,合成了聚醚聚酰胺酸;然后以不同重量比将聚醚聚氨酯和聚醚聚酰胺酸溶液混合反应亚胺化,制备了一系列不同硬段含量的聚醚聚氨酯－聚醚聚酰亚胺合金。用傅立叶变换红外光谱、动态力学分析、示差扫描量热、广角Ｘ－衍射、应力应变试验等分析测试方法对合金进行了研究,结果表明聚醚聚氨酯－聚醚聚酰亚胺合金具有很好的相分离结构,是一类新型耐高温、有韧性的热塑性弹性体。聚醚分子量相同的聚氨酯和聚酰亚胺形成的合金软段相容,合金具有两相结构;聚醚分子量不同的聚氨酯和聚酰亚胺形成的合金软段存在相分离,合金具有三相结构,表现在材料外观上分别为透明不透明的韧性膜,少量聚酰亚胺的掺入,能大大增加材料的耐热性能,而合金的材料力学性能没有明显变化。     

含有二个聚醚软链段的聚醚聚酯嵌段共聚物的合成及其血液相容性的研究

本文报道了一类新的具有二种聚醚软链段(PTMGT和PEGT)和一种聚酯硬链段(PET)的混合聚醚-聚酯嵌段共聚物(MPEE)的合成和它的血液相容性,并与具有相同软、硬链段比及相同软链段组成比(PTMGT/PEGT)的二种聚醚聚酯嵌段共聚物(PTMGT-PET和PEGT-PET)的共混物(BPEE)的性质进行了比较,结果表明:(1)聚醚聚酯嵌段共聚物的血液相容性可以通过引入亲水性好的PEGT组分而得到提高;(2)在多数的组成比下,共聚型的MPEE具有比共混型的BPEE优良的血液相容性;(3)特定的组成比:PTMGT/PEGT=60/40(mol),共混型的BPEE:(60/40)呈现最好的血液相容性以及最佳的力学性质。研究中发现材料的微相分离结构同血液相容性有关,细微的相分离结构可导致优良的血液相容性。     

聚醚氨酯的微区形态

<正> 聚醚氨酯热塑弹性体是属于(AB)n类型的线型多嵌段共聚物,包括交替的硬段和软段单元.自从1966年Cooper和Tobolsky首先提出聚氨酯具有微相分离的本体结构之假设以后,至今已有大量文献报道了这类材料结构形态与性能关系的研究结果. Wilkes和Koberstein等使用SAXS研究了聚氨酯体系的形态特征.一般认为,聚氨酯材料的微相结构包括一个叠层状或类似叠层状形态,由相分离的软段和硬段组成,平均尺寸为100A的数量级,在软硬段微区之间还存在一相混合的过渡区,其厚度可以从几个埃至几十个埃.然而,SAXS虽然能够高分辨地给出多相体系相分离情况的定     

含有二个聚醚软链段的聚醚聚酯嵌段共聚物的合成及其血液相容性的研究

 本文报道了一类新的具有二种聚醚软链段(PTMGT和PEGT)和一种聚酯硬链段(PET)的混合聚醚-聚酯嵌段共聚物(MPEE)的合成和它的血液相容性,并与具有相同软、硬链段比及相同软链段组成比(PTMGT/PEGT)的二种聚醚聚酯嵌段共聚物(PTMGT-PET和PEGT-PET)的共混物(BPEE)的性质进行了比较,结果表明:(1)聚醚聚酯嵌段共聚物的血液相容性可以通过引入亲水性好的PEGT组分而得到提高;(2)在多数的组成比下,共聚型的MPEE具有比共混型的BPEE优良的血液相容性;(3)特定的组成比:PTMGT/PEGT=60/40(mol),共混型的BPEE:(60/40)呈现最好的血液相容性以及最佳的力学性质。研究中发现材料的微相分离结构同血液相容性有关,细微的相分离结构可导致优良的血液相容性。     

交联密度对脂肪族聚氨酯弹性体结构与性能的影响

采用异佛尔酮二异氰酸酯(IPDI)与聚醚二元醇、三羟甲基丙烷(TMP)和1,4-丁二醇反应制备了具有不同交联密度的脂肪族聚氨酯弹性体.研究结果表明,当聚氨酯弹性体的硬段含量为40 wt%时,随着TMP含量的增加,聚氨酯弹性体的交联密度线性增加.随着聚氨酯弹性体交联密度的提高,聚氨酯中硬段相的玻璃化转变温度由32℃降为2...     

用正电子湮没谱研究聚酯型聚氨酯的微观结构和自由体积特性

用正电子湮没谱研究了两类分别由聚己二酸丁二醇酯多元醇和聚ε 己内酯多元醇合成的线型聚酯型聚氨酯 (PBU和PCU)在 140～ 36 0K温度范围内的结构转变和自由体积特性 .研究结果表明 ,两类聚氨酯(PU)在 140～ 36 0K温度范围内 ,都存在三个转变点 ,其中较低温度的转变 (约 2 0 0K)对应于PU中软段的玻璃化转变温度 (Tg) ,2 75K处的转变可能与样品吸附少量水分有关 ,较高温度的转变 (约 310K) ,对于PBU而言对应于软段结晶的熔点 ,而对于PCU则与在无序的硬段中混入一定量的软段后形成的相容区的Tg 有关 .当温度低于PU软段的Tg 时 ,两类PU的自由体积尺寸和浓度都随温度升高而增大 .当温度高于软段的Tg 但低于2 75K时 ,自由体积尺寸较快地增加 ,而自由体积浓度保持不变 .温度高于 2 75K并低于软段的熔点或硬段 软段相容区的Tg 时 ,自由体积尺寸增加速度最快 ,自由体积浓度却保持同样的数值 .当温度进一步升高时 ,自由体积尺寸和浓度都随温度增大而增加 .最后研究了这两类PU的自由体积分布与温度的关系 .所有这些实验现象均与大分子链的运动有关 ,并与通过DSC和WAXD表征的材料的形态一致     

聚酯型脂肪族和芳香族聚氨酯硬段结晶特性对比

本文利用DSC、IR、WAXD、PLM和SALS等实验手段,探讨了具有相同软段的聚酯型脂肪族和芳香族聚氨酯硬段结晶特性的差异,发现脂肪族聚氨酯的相分离速率极快,氢键主要在硬段间形成,因而对硬段的结晶过程影响不大;而芳香族聚氨酯的相分离速率较慢,软硬段间又能形成氢键,因而对硬段的结晶起了阻碍作用。     

Phase morphology of hydrolysable polyurethanes derived from aqueous dispersions

Biodegradable polyurethanes are an interesting alternative to many applications that involve plastics since they can minimize environmental problems caused by the low rates of natural degradation of synthetic polymers. In addition, since waterborne polyurethanes are based on aqueous dispersions, they restrict the use of organic solvents during processing and application of the polymer, thus contributing furthermore to reduce environmental damage. In this work, aqueous anionic polyurethane dispersions (PUD) with tailorable susceptibility for hydrolysis were synthesized by progressively replacing polypropylene glycol (PPG) with a biodegradable polycaprolactone diol (PCL) as soft segments. The hard segments were formed by extending isophorone diisocyanate (IPDI) with hydrazine (HZ). Dimethylol propionic acid (DMPA) was used as ionic center and triethyl amine (TEA) as neutralizer. The degree of phase separation was evaluated mainly by infrared spectroscopy (FTIR) and small angle X-ray scattering (SAXS). The results indicated that phase separation between hard and soft segments of poly(ester-urethane) is more significant than that of poly(ether-urethane). Data obtained from SAXS experiments indicated that phase separation within soft domains can also be present in samples containing both polyester and polyether soft segments. Hydrolytic degradation of the polymers in buffer solution of pH 7.4 and alkaline solution was performed as an initial test. The results showed that the fraction of polyester soft segments in the polyurethanes can be used to tailor the susceptibility of the materials to hydrolytic attack. Polyurethanes having higher contents of polyester were more promptly hydrolytically degraded than polyurethanes containing only polyether segments.     

聚硅氧烷聚脲多嵌段共聚物中氢键的研究

采用多种手段研究了聚硅氧烷与聚脲嵌段共聚物中所存在的各类氢键．特别探讨在聚硅氧烷软段中引入极性氰丙基对体系成氢键能力的影响和两相间相互作用力的情况结果表明，在软段分子中引入极性氰丙基有利于增加聚硅氧烷分子与聚脲链段的相互作用，这一相间作用力使两相间界面层厚度随着硬段分子量的增加而加宽，并发现在聚硅氧烷聚脲嵌段共聚物中硬段的聚集形态随溶液浓度改变变化不大，其中氢键随着温度升高而下降．     

Structure-property relationships in polycaprolactone-polyurethanes

The structure-property relationships of polycaprolactone-based segmented polyurethanes were studied using differential scanning calorimetry (DSC), small-angle x-ray scattering (SAXS), wide-angle x-ray diffraction (WAXD), dynamic mechanical, and stress-strain testing. The materials studied varied in hard-segment type [4,4′-diphenylmethane diisocyanate/butanediol (MDI/BD) or 4,4′-dicyclohexyl methane diisocyanate/butanediol (H₁₂MDI/BD)], soft-segment molecular weight (830 or 2000 MW polycaprolactone), hard-segment content (23–77% by weight), and thermal history. The materials with aromatic (MDI/BD) hard segments had semicrystalline hard-segment domains, while the materials with aliphatic (H₁₂MDI/BD) hard segment had mostly amorphous domains. Materials with the shorter polycaprolactone soft segment (830 MW) exhibited thermal and mechanical behavior which indicated a considerable degree of hard- and soft-segment compatibility. The materials which contained a 2000-MW polycaprolactone soft segment exhibited better-defined microphase separation. SAXS was used to characterize the microphase structure of each system. The effects of hard-segment content and soft-segment molecular weight were similar for the aromatic (MDI) and aliphatic (H₁₂MDI) hard-segment-based block copolymers. Changing the hard segment from aromatic to aliphatic gave materials with larger interfacial area and slightly higher tensile strength. A range of morphologies between isolated hard domains in a rubbery matrix and isolated rubbery domains in a hard matrix was observed.     

STUDIES ON THE SPHERULITE FORMATION IN MELT CAST POLYCAPROLACTONE BASED POLYURETHANES

A series of PCL/MDI/BDO segmented polyurethanes have been synthesized by two-step method in solution.The hard segment content ranges from 10% to 48% by weight, and the molecular weight of PCL diols is 1500. Hard segment spherulites have been observed in compression molded specimens of all of the samples except the one of the lowest hard segment content. The difficulty in sphernlite formation was explained as only in a small temperature range,the microphase separation rate may be faster than the crystallization rate and all these processes are very slow due to the hydrogen bonding between hard and soft segments and the interactions between hard segments themselves. PCL soft segments of molecular weight 1500 is still crystallizable and may form different crystalline superstructures.     

The degradation and biocompatibility of waterborne biodegradable polyurethanes for tissue engineering

To better investigate the degradation and biocompatibility of waterborne biodegradable polyurethanes for tissue engineering, a series of new waterborne biodegradable polyurethanes (PEGPUs) with low degree of crosslinking was synthesized using IPDI, BDO and L-lysine as hard segments, PCL and PEG as soft segment. The bulk structures and properties of the prepared polyurethanes were characterized by Fourier transform infrared spectroscopy (FTIR), differential scanning calorimetry (DSC), tensile mechanical tests and water contact angle (WCA) measurements. The degree of microphase separation was slightly improved because of the lowered crosslinking degree of these PEGPUs in comparison with the high cross-linking degree samples, leading to good mechanical properties, as indicated by DSC and stress-strain data. Moreover, biodegradability of the polyurethanes was evaluated in phosphate buffer solutions (PBS) under different pH values and enzymatic solution at pH 7.4 through weight loss monitoring. The results suggested that the degradation of these PEGPUs was closely related to their bulk and surface properties. And the degradation products didn’t show apparent inhibition effect against fibroblasts in vitro. These studies demonstrated that the waterborne biodegradable polyurethanes could find potential use in soft tissue engineering and tissue regeneration.     

聚乙二醇型聚氨酯软硬段对其相变储热性能的影响

以不同分子量的聚乙二醇(PEG)为软段,MDI-BDO为硬段,采用两步法溶液聚合合成一种具有固-固相变储热性能的聚氨酯材料.通过DSC,WAXD等测试手段对体系的软硬段结晶性,微相分离,相变可逆性及循环热稳定性进行研究,结果表明,聚氨酯中硬段的存在对软段结晶有着很大的影响,当软段分子量达到2000或以上时,软段才具有较大的结晶度和熔融相变焓,且硬段含量必须高于一定值才能形成较为完善的物理交联网络以保证材料在发生相变时维持固体状态.同时符合这两个条件的试样能具有较好的固-固相变储热性能.就软段PEG含量及分子量对材料储热性能的影响进行了研究,通过调节软段含量与分子量得到一系列具有不同相变焓和相变温度的聚氨酯固-固相变储热材料.经测试还发现,该材料具备很好的相变可逆性和循环热稳定性,是一类很有开发前景的相变储热材料.     

不同软段结构的双离子型聚氨酯离聚体

本文讨论了以聚环氧乙烷(PEO)、聚环氧丙烷(PPO)以及聚丁二烯(PBD)为软段,以4,4’-二异氰酸二苯甲烷(MDI)和N,N-二羟乙基甲胺(MDEA)为硬段的链段型聚氨酯的合成。并通过MDEA中的第三胺与Υ-丙磺内酯反应,转化为双离子型离聚体。用差示扫描量热、红外光谱、动态力学性能以及应力-应变等实验方法研究了化学组成和氨磺化程度对材料相分离程度,力学性能和形态结构的影响。结果表明,离子化后的材料力学性能有很大的改善。对PBD为软段的材料,离子化只能提高硬段“微区”的内聚能,而对PEO、PPO为软段的材料,还能大大提高软、硬相的相分离程度。     

Effect of Chain Extender on Hydrogen Bond and Microphase Structure of Biodegradable Thermoplastic Polyurethanes

Thermomechanical properties of polyurethanes (PUs) strongly depend on the molecular interactions and microphase structure.In this work,two chain extenders with different ratios,flexile 1,4-butanediol (BDO) and branched trimethylolpropane mono allyl ether (TMPAE),are used to tune the molecular interactions and microphase structures of a series of biodegradable thermoplastic polyurethanes (TPUs).In TPUs,the biodegradable polycaprolactone (PCL,Mn of 2000) is used as soft segment while 1,6-diisocyanatohexane (HDI) and chain extenders are used as hard segment.Fourier transform infrared spectroscopy (FTIR),proton nuclear magnetic resonance spectroscppy (1H-NMR),gel permeation chromatography (GPC),differential scanning calorimetry (DSC),dynamic mechanical analysis (DMA) and mechanical tests were performed to characterize the bulk structure and properties of TPUs.Compared with BDO,the steric bulk of TMPAE is larger.The increment of TMPAE can help to increase the hydrogen bond content,microphase separation,and the elastic modulus ratio (R),which would strongly affect the thermomechanical property of the TPUs.The results of this work verify the importance of the structure of chain extender on the properties of TPUs.It provides valuable information for further understanding the structure-property relationships of these polyurethanes.