Ru/CNTs-Al2O3氨合成催化剂的制备与表征

采用H₂O₂、HNO₃和空气等氧化剂(ox)对碳纳米管-氧化铝(CNTs-alumina)复合材料进行纯化改性处理, 制备了Ru/CNTs-alumina-ox系列催化剂. 透射电镜(TEM), 热重(TG), X射线衍射(XRD)和傅里叶变换红外(FTIR)光谱分析结果表明, CNTs-alumina-H₂O₂复合载体中碳管结晶度最好, 且部分碳管被打断, 长度变短, 使其表面的羟基、羧基和羰基的含量明显提高. 电感偶合等离子体发射光谱(ICP)分析结果还表明, 经HNO₃处理时CNTs-alumina-HNO₃复合载体中有Al的溶出, 溶液中Al含量为49.98 mg·g^-1. 经三种氧化剂处理后所得到的催化剂, 其结构和表面化学性质存在明显的差别, 影响了氨合成催化剂的活性, 其中以CNTs-alumina-H₂O₂复合载体制备的催化剂氨合成活性最高, 在10 MPa、425 °C、10000 h^-1条件下, Ru/CNTs-alumina-H₂O₂催化剂氨合成反应速率达到39.8 mmol·g^-1·h^-1.     

纳米SO42-/ZrO2的合成及其在酯交换反应中的催化性能

采用两步晶化-后浸渍法合成了纳米SO₄^2-/ZrO₂固体酸催化剂,并考察了其在植物油与甲醇酯交换反应中的催化性能。XRD、N₂吸附-脱附和TEM等结果表明,经过600℃焙烧,催化剂仍保持单一四方相,粒径大小为5~10 nm,比表面积为137 m²·g^-1,孔径为3.6 nm。NH₃-TPD结果表明,随着焙烧温度升高,催化剂表面的酸含量和酸强度逐渐增加,超强酸含量的增加,更有利于反应在温和条件下进行。在酯交换反应中,当醇油物质的量之比为20：1,反应温度为135℃,反应时间为6 h,600℃焙烧后催化剂用量为5%（w/w）时,植物油能够完全转化为脂肪酸甲酯。与传统的SO₄^2-/ZrO₂催化剂相比,该催化剂在低温反应条件下具有更高的催化性能和良好的重复使用性。     

单核钌催化剂化学催化和光催化水氧化反应

合成了一系列含有不同对位取代基团的吡啶轴向配体的单核钌化合物Ru(bda)(pic)₂ (H₂bda=2,2''-联吡啶-6,6''-二羧酸; pic=对甲基吡啶),对化合物的结构进行了核磁、质谱和X射线单晶衍射表征,并在中性和酸性条件下研究了这些化合物的电化学性质.以硝酸铈铵为氧化剂,对催化剂的催化活性进行了测试,并以[Ru(bpy)₃]²⁺为光敏剂,S₂O₈^2-为电子牺牲剂,在三组分体系中考察了这些化合物的光催化活性.研究发现,在化学法水氧化反应中,化合物1由于其轴向配体4,4''-联吡啶在酸性条件下能够发生质子化,从而增强了吸电子效应,因此表现出最高的催化活性,催化循环数达到4000.在光催化水氧化反应中,化合物2因其轴向配体具有最强的吸电子能力而表现出最高的催化活性,反应2h的催化循环数达到270.结果表明,轴向配体的吸电子能力明显提高了这类Ru催化剂催化水氧化反应活性.     

焙烧温度对MnOx-CeO2-WO3-ZrO2催化剂上NH3选择性还原NO的影响

采用共沉淀法制备了MnO_x-CeO₂-WO₃-ZrO₂催化剂,考察了催化剂焙烧温度对O₂和H₂O存在下NH₃选择性催化还原（NH₃-SCR） NO的影响,并利用低温N₂吸附、X射线衍射（XRD）、透射电镜（TEM）、X射线光电子能谱（XPS）、NH₃程序升温脱附（NH₃-TPD）和CO脉冲反应对催化剂进行了表征. 结果表明在NH₃-SCR反应中,催化剂的低温活性随焙烧温度的提高而降低,这是由于催化剂表面化学吸附氧和酸性位减少引起的;催化剂的高温活性随焙烧温度的提高先增加后减小,这与催化剂表面最易释放氧数量的变化趋势相反. 700 ℃焙烧的催化剂具有良好的低温活性和最宽的反应温度窗口,在空速为90000 h^-1的条件下,该催化剂的起燃温度（50% NO转化率）为189 ℃,且反应温度在218-431 ℃范围内,NO转化率可达到80%-100%.     

碱性CeO2载体对Ru/CeO2催化剂氨合成活性的影响

钌基催化剂因其在低温低压下具有比常规的铁基催化剂更具活性的特点成为合成氨催化剂的理想选择.我们研究了CeO₂载体表面碱性对Ru基合成氨催化剂的影响.通过调节KOH沉淀剂的量来制备具有不同碱性位点的CeO₂载体（pH=10/11/12）,证明了催化剂适当碱性位点密度提高了合成氨催化活性.催化性能测试结果表明,1.25% Ru/CeO₂-11催化剂在3.8 MPa,450℃,H₂/N₂=3（60 mL·min^-1）下表现出优异的氨合成活性（7040 μmol·g^-1·h^-1）.CeO₂-11的碱性位点增强了载体的电子给予能力,这有利于电子向活性金属Ru转移,从而促进了N₂的活化.碱金属和碱土金属的引入提高了活性金属Ru的还原能力.4% Cs-1.25% Ru/CeO₂-11（12 000 μmol·g^-1·h^-1）催化剂具有更多的氧空位,这增加了Ru周围的电子密度并促进了N≡N的裂解.通过XRD,BET,SEM,CO₂-TPD,H₂-TPR和XPS分析了不同碱性CeO₂载体对合成氨催化反应的影响.     

NO2对Cu/SAPO-34分子筛催化剂上NH3选择性催化还原NO性能的影响

主要考察了NO₂对Cu/SAPO-34 分子筛催化剂在整个温度范围内（100-500 ℃）NH₃选择性催化还原（SCR）NO性能的影响. 研究所使用样品为新鲜Cu/SAPO-34 催化剂在750 ℃下水热处理4 h 的稳定期样品.通过X射线衍射（XRD）和扫描电子显微镜（SEM）对样品的结构以及形貌进行表征,采用SCR活性评价、动力学实验以及原位漫反射傅里叶变换红外光谱（in situ-DRIFTS）表征催化剂的性能以及催化剂表面物种的变化. 活性评价实验结果表明,NO₂会抑制催化剂的低温（100-280 ℃）活性,但其存在会提高催化剂的高温（280 ℃以上）活性. 与此同时,随着反应物中NO/NO₂的摩尔比例减少,由于NH₄NO₃物种的分解,副产物（N₂2O）的浓度增大. 动力学结果表明,Cu/SAPO-34 催化剂上快速SCR反应的表观活化能（E_a=64.02 kJ·mol^-1）比标准SCR反应的表观活化能（E_a=48.00 kJ·mol^-1）更大. In situ-DRIFTS实验结果表明NO比NO₂更容易在催化剂表面形成硝酸盐,并且NO₂更容易与吸附在Brønsted 酸性位上的NH₃物种反应生成NH₄NO₃. 低温下,催化剂表面的NH₄NO₃物种会覆盖SCR反应的活性位,造成活性降低,但在高温时,形成的NH₄NO₃物种一部分会被NO还原为N2,而另一部分会直接热分解为N₂O,造成催化剂的选择性降低.     

介孔炭的孔结构对其负载的Ru基氨合成催化剂性能的影响

采用模板法合成了介孔炭(MC),研究了其孔结构对其负载的Ru基氨合成催化剂Ba-Ru-K/MC性能的影响,采用N₂吸附脱附、扫描电镜和透射电镜等手段对介孔炭的孔结构进行了表征.研究发现,介孔炭载体的孔结构取决于模板剂的用量,当SiO₂/C质量比为1.0时,所制介孔炭比表面积最大.介孔炭负载的Ba-Ru-K催化剂活性与其介孔比表面积相关.在425℃,10MPa和10000h^-1条件下,合成氨的反应速率为139mmol/(g_cat·h).     

Ni-Cu双金属催化剂上乙醇水蒸气重整制氢研究—制备方法对催化性能的影响

我们采用分步浸渍法和共浸渍法制备了一系列的Ni-Cu/mSiO₂催化剂.运用XRD、N₂吸附-脱附、H₂-TPR、SEM、TG-DTG等表征手段对催化剂反应前后的物理化学性质进行分析,催化剂对乙醇水蒸气重整（ESR）反应的催化性能通过常压固定床反应器进行评价.结果表明：催化剂的催化性能与载体上的活性组分分散有关,而活性金属的分散性与制备方法有关.共浸渍法制备的催化剂Ni₁₄-Cu/mSiO₂活性组分分散度较高,抗积碳能力与稳定性更好.在质量空速为2.7 h^-1,水醇摩尔比为9,反应温度为550℃的条件下进行稳定性测试,催化剂Ni₁₄-Cu/mSiO₂测试25 h没有出现失活现象,乙醇转化率保持在100%,H₂的选择性保持在70%以上,反应后的积碳含量仅为5.52%.     

Pt/TiO2催化剂上CO氧化反应动力学研究

利用沉积沉淀法制备了Pt/TiO₂催化剂, 将其在不同温度下焙烧, 以得到不同颗粒尺寸的Pt. 并将这些样品用于CO催化氧化反应以及反应动力学研究. 结果表明: 焙烧温度对催化剂有明显影响, Pt 颗粒尺寸随着焙烧温度的升高而增加; 与此同时, CO催化活性随焙烧温度的升高呈先增加后降低的趋势, 其中, 400℃焙烧的样品表现出最高的催化活性. 反应动力学结果表明, 催化剂上CO氧化反应表观速率方程为r=5.4×10^-7p_CO^0.17p_O2^0.36,说明在该催化剂上CO氧化遵循Langmuir-Hinshelwood机理. 同时, 对催化剂进行了CO化学吸附红外光谱和O₂化学吸附表征. 结果表明, 随着焙烧温度的升高, 催化剂上CO和O₂吸附量均呈现先升高后降低的趋势, 这与反应结果和反应动力学方程一致, 说明反应受到催化剂表面上CO和O₂吸附浓度的影响. 而在400℃焙烧的催化剂上, CO和O₂吸附量均最高, 因此其反应活性也最好. 这可能是焙烧过程影响了Pt 和TiO₂之间的相互作用引起的.     

高比表面介孔LaNiO3负载纳米Au催化剂的研究

分别采用纳米铸型法和溶胶-凝胶法制备了系列LaNiO₃载体,并用沉积-沉淀法制备了系列Au/LaNiO₃催化剂.对催化剂进行了XRD、BET、AAS、TEM和XPS等表征,测试了其对CO催化氧化活性.实验结果表明,纳米铸型法得到的LaNiO₃-NCM具有介孔结构,且比表面积可达126 m²·g^-1,以其为载体制备的Au/LaNiO₃-NCM催化剂在30℃条件下将CO完全转化,活性远高于以传统溶胶-凝胶法制备的LaNiO₃-SG为载体的金催化剂.XPS结果表明该Au/LaNiO₃-NCM催化剂表面存在较多的氧化态Au^δ+（0 < δ < 3）和晶格氧,且活性组分Au含量也较高,说明高比表面介孔LaNiO₃载体有利于提高活性组分Au的负载量,从而提高催化剂催化活性.     

费托合成CeO2助Co/SiO2催化剂的失活

在固定床反应器上考察了原粒度(1～3mm)CeO2助Co/SiO2催化剂的费托反应性能,提出了催化剂失活的机理,并采用程序升温还原、X射线衍射和X射线光电子能谱对催化剂进行了表征.结果表明,在1.5MPa,488K和400h-1条件下进行的300h稳定性实验中,原粒度CeO2助Co/SiO2催化剂上的CO平均转化率达到41%,液态烃选择性达到85%,液态烃中C10 烃的质量含量占88%以上.反应器出口的催化剂中有少量的CoO和Co2SiO4生成.催化剂的失活过程受动力学控制而非热力学控制,催化剂的失活机理为:高分散的纳米Co离子在反应器出口高水蒸气压力的作用下,以CoO为中间物种,与水合SiO2作用生成Co2SiO4,即Co H2O→CoO H2,SiO2 H2O→OSi(OH)2,2CoO OSi(OH)2→Co2SiO4 H2O.     

Aqueous-Phase Nitrile Hydration Catalyzed by an In Situ Generated Air-Stable Ruthenium Catalyst

RuCl₂(PTA)₄ (PTA=1,3,5-triaza-7-phosphaadamantane) is an active, recyclable, air-stable, aqueous-phase nitrile hydration catalyst. The development of an in situ generated aqueous-phase nitrile hydration catalyst (RuCl₃⋅3 H₂O+6 equivalents PTA) is reported. The activity of the in situ catalyst is comparable to RuCl₂(PTA)₄. The effects of [PTA] on the activity of the reaction were investigated: the catalytic activity, in general, increases as the pH goes up, which shows a positive correlation with [PTA]. The pH effects were further explored for both the in situ and RuCl₂(PTA)₄ catalyzed reaction in phosphate buffer solutions with particular attention given to pH 6.8 buffer. Increased catalytic activity was observed at pH 6.8 versus water for both systems with turnover frequency (TOF) up to 135 h⁻¹ observed for RuCl₂(PTA)₄ and 64 h⁻¹ for the in situ catalyst. Catalyst loading down to 0.001 mol % was examined with turnover numbers as high as 22 000 reported. Similar to the preformed catalyst, RuCl₂(PTA)₄, the in situ catalyst could be recycled more than five times without significant loss of activity from either water or pH 6.8 buffer.     

Study of activated carbon supported iron catalysts for the Fischer-Tropsch synthesis

Summary Characterization (BET and TPD) and reaction studies were conducted with activated carbon supported iron catalysts (Fe/AC) used for the Fischer-Tropsch synthesis (FTS). The TPD study showed that there existed interactions between metals and the AC surface. Greater association of Cu and K promoters with the AC surface resulted in stronger promoter to surface interaction, which enhanced the H₂ desorption ability of the Cu and K promoted Fe/AC catalyst prepared under vacuum impregnation (VI). Catalytic behavior of a Fe/AC catalyst (VI-15 Fe/2 Cu/2 K/81 AC, in parts per weight) was studied in a 1-liter slurry phase continuous stirred tank reactor. The catalyst presented moderate syngas conversion (44.3-60.6%) and high gaseous selectivity (CH₄, 12.8-15.1% and C₂-C₄, 42.4-46.1%) under 304^oC, 3.0 MPa, 1.1 L(STP)/g-cat/h, and H₂/CO = 2.0 during 166 h of testing. Detectable hydrocarbons up to C₁₈ were formed on the Fe/AC catalyst.     

Enhancement of distillate selectivity in Fischer-Tropsch synthesis by using iron and cobalt catalysts in a novel dual-bed reactor ?

Summary An integrated process for producing liquid fuels from synthesis gas via a two-stage Fischer-Tropsch (FT) reaction is disclosed. An iron catalyst was used in the first bed of a fixed-bed reactor followed by a ruthenium promoted cobalt catalyst in the second bed. The activity and selectivity of the dual-bed system were assessed and compared with those using catalysts in a single bed system, separately. The methane selectivity in the dual-bed reactor was about 11% less compared to that of the single-bed system. The C₅⁺ selectivity for the dual-bed reactor was 19.7% higher than that of the single-bed system.     

Mo 和 Cu 助剂对 FeK/SiO2 催化剂费托合成性能的影响

 研究了 Mo 和 Cu 助剂对 FeK/SiO₂ 催化剂的性质及费托 (F-T) 合成性能的影响. 采用 N₂ 物理吸附、H₂ 程序升温还原、X 射线衍射、穆斯堡尔谱和 X 射线光电子能谱技术对催化剂进行了表征. 结果表明, Mo 加入后与 Fe 产生了较强的相互作用, 抑制了催化剂的还原和碳化; Cu 助剂的加入促进了催化剂的还原和碳化; 当 Mo 和 Cu 共同加入后, 催化剂的还原和碳化行为与单独加入 Cu 助剂时相似. 催化剂 F-T 合成性能在固定床上于 280 ^oC, 1.5 MPa, 2 000 h^-1, H₂/CO = 2.0 的合成气中测试. 结果表明, Mo 的加入降低了催化剂活性, 但提高了重质烃 (C₅₊) 的选择性; Cu 的添加提高了催化剂的活性, 但对稳定 C₅₊选择性作用不明显. Mo 和 Cu 共同加入后, 催化剂既表现出较为稳定的 C₅₊选择性, 同时其活性也没有降低.     

Iron-based catalysts encapsulated by nitrogen-doped graphitic carbon for selective synthesis of liquid fuels through the Fischer-Tropsch process

Fischer-Tropsch synthesis (FTS) has the potential to be a powerful strategy for producing liquid fuels from syngas if highly selective catalysts can be developed. Herein, a series of iron nanoparticle catalysts encapsulated by nitrogen-doped graphitic carbon were prepared by a one-step pyrolysis of a ferric L-glutamic acid complex. The FeC-800 catalyst pyrolyzed at 800 °C showed excellent catalytic activity (239.4 μmol_CO g_Fe^–1 s^–1), high C₅–C₁₁ selectivity (49%), and good stability in FTS. The high dispersion of ferric species combined with a well-encapsulated structure can effectively inhibit the migration of iron nanoparticles during the reaction process, which is beneficial for high activity and good stability. The nitrogen-doped graphitic carbon shell can act as an electron donor to the iron particles, thus promoting CO activation and expediting the formation of Fe₅C₂, which is the key factor for obtaining high C₅–C₁₁ selectivity.     

TiO2 supported cobalt-manganese nano catalysts for light olefins production from syngas

Cobalt-manganese nano catalysts were prepared by sol-gel method. This research investigated the effects of different cobalt-manganese (Co/Mn = 1/1) loading, pH and calcination conditions on the catalytic performance of Co-Mn/TiO₂ catalysts for Fischer-Tropsch synthesis (FTS) in a fixed bed reactor. It was found that the catalyst containing 30wt%(Co-Mn)/TiO₂ was an optimal catalyst for the conversion of synthesis gas to light olefins especially propylene. The activity and selectivity of optimal catalyst were studied under different operational conditions. The results showed that the best operational conditions were H₂/CO= 1/1 molar feed ratio at 250 °C and GHSV= 1300 h^?1 under atmospheric pressure. Characterization of catalysts was carried out by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), N₂ adsorption-desorption measurements.     

Fuzzy model prediction of Co (III)Al2O3 catalytic behavior in Fischer-Tropsch synthesis

The application of Co(Ⅲ)/Al2O3 catalyst in Fischer-Tropsch synthesis(FTS)was studied in a wide range of synthesis gas conversions and compared with Fuzzy Simulation results.Present study applies fuzzy model to predicting the product composition of CH4,CO2 and CO in Fischer-Tropsch process for natural gas synthesis,in which the input vector was 4-dimension including four variables(operating pressure, operating temperature,time and CO/H2 ratio)of 70 different experiments and the output product is a composition of CO2,CO and CH4. The Mamdani algorithm has been applied to the training of the fuzzy system and the test set was used to evaluate the performance of the system including R2,ARE,AARE and SD.The results demonstrated that the predicted values from the model were in good consistency with the experimental data.The work indicates how fuzzy inference system(FIS),as a promising predicting technique,would be effectively used in FTS.     

Catalytic Activity of Thermolyzed [Co(NH3)6][Fe(CN)6] in CO Hydrogenation Reaction

Currently, the processes of obtaining synthetic liquid hydrocarbons and oxygenates are very relevant. Fischer-Tropsch synthesis (FTS) is the most important step in these processes. The products of thermal destruction in argon of the mixture [Co(NH₃)₆][Fe(CN)₆] and Al(OH)₃ were used as catalysts for CO hydrogenation. The resulting compositions were studied using powder X-ray diffraction, IR spectroscopy, elemental analysis, SEM micrographs. The specific surface area, pore and particle size distributions were determined. It was determined that the DCS-based catalysts were active in the high-temperature Fischer-Tropsch synthesis. The effect of aluminum in the catalyst composition on the distribution of reaction products was revealed.     

XPS and ISS analysis of Fischer-Tropsch catalysts

Summary The surface compositions of K and Cu containing Fe/Mn oxide catalysts for Fischer-Tropsch synthesis were investigated by XPS and ISS. The surface species after calcination are identified as Fe₂O₃, Mn₂O₃, MnO₂, CuO and most likely KO₂, and after in situ reduction at 723 K Fe⁰, Cu⁰, Fe²⁺ and Fe³⁺ oxides, MnO and KOH. Mn and K are enriched on the surfaces after calcination and reduction; the Cu surface content is approximately equal to the bulk concentration. The K enrichment is especially strong and ISS indicates that potassium is mainly confined to the uppermost layers. The degree of reduction of Fe is strongly dependent on the amount of Cu or K. The change in surface composition during Fischer-Tropsch reaction in the XPS equipment can be correlated to the activity of the catalysts. The pure and Cu containing samples show a constant activity and only a small increase in carbon surface concentration. The K containing catalysts deactivate after a short time and are then totally covered by carbon. On all catalyst surfaces a small amount of carbonate is formed.

---

XPS- and ISS-Analyse von Fischer-Tropsch-Katalysatoren